Fitting Instructions - Rhino-Rack
Contents
1. di Make sure that the upper clamp assembly does not interfere with the crossbar legs as shown e 3 Assemble fairing as shown only insert one bolt assembly for the moment so it Il be easy to mount onto the crossbar Do not tighten fully keep it loose Page 5 of 6 Rhino Rack Fairing RF1 RF2 RF3 RF4 5 Tighten M6 bolts evenly across the upper clamp assembly Ensure that the fairing is mounted centrally on the crossbar Ensure that the load does not damage the plastic clamp brackets sits above the dotted line as shown Regularly inspect and replace if necessary Page 6 of 62. to the weight of the crossbars and legs WARNING Important Load Carrying Instructions With utility vehicles the cabin and the canopy move independently Roofracks and vehicle can be damaged if the item transported is rigidly fixed at points on both the cabin and canopy Instead rigidly fix to either the cabin roofracks or the canopy roofracks Page 2 of 6 Rhino Rack Fairing RF1 RF2 RF3 RF4 Parts List tem componentName wIRFN GW RF2 RFS RFA Paro a rm ton Head Screw Be mo tata oo oo Pea IT TT St CT E CCS Pe Fame ST Pes CT ET DE O Pes IT TC NET CS CS GP estere CI 8 ca e mene ST Fitting Instruction Tools Required MAX width 90mm Security Allen key provided in kit MIN width N A MAX height 33mm MIN height 22mm RF1 Parts List Upper clamp comes pre assembled Page 3 of 6 Rhino Rack Fairing RF1 RF2 RF3 RF4 Fitting instructions RF1 shown here Measure the distance between your rails and your crossbar legs before selecting the appropriate fairing for your vehicle Page 4 of 6 Rhino Rack Fairing RF1 RF2 RF3 RF4 P Make sure that there are sufficient clearances for the fitment of the fairing Ensure that the fairing clears the roof rails on the roof of your vehicle
3. RHINO RACK Rhino Rack Fairing RF1 RF2 RF3 RF4 Important Please read these instructions carefully prior to installation Please refer to your fitting instruction to ensure that the fairing is installed in the correct locations Check the contents of kit before commencing fitment and report any discrepancies Place these instructions in the vehicle s glove box after installation is complete Important Information Recommendations It is essential that all bolt connections be checked after driving a short distance when you first install your cross bars Bolt connections should be checked again at regular intervals probably once a week is enough depending on road conditions usage loads and distances travelled You should also check the cross bars each time they are re fitted Make sure to fasten your load securely Please ensure that all loads are evenly distributed and that the centre of gravity is kept as low as possible Use only non stretch fastening ropes or straps Do not use fairing as a tie off point Always lash around crossbar Sensitivity to cross winds behaviour in curves and braking The handling characteristics of the vehicle changes when you transport a load on the roof For safety reasons we recommend you exercise extreme care when transporting wind resisting loads special consideration must be taken into account when braking Please remove cross bars when putting vehicle through an automatic car wash Clean fairing wit
4. h smooth cloth using water or mild washing liquid Damage to plastic may occur if the washing liquid is too strong or concentrated Raise fairing slightly when cleaning the vehicle roof Rhino Rack do not take responsibility for damage to vehicle paintwork caused by this product The best materials have been selected to minimise the impact of the contact between automotive grade rubber and the paintwork It is the responsibility of the end user to determine the suitability of this product with their vehicle Note for Dealers and Fitters It is your responsibility to ensure instructions are given to the end user or client Rhino Rack 3 Pike Street Rydalmere Document No R286 NSW 2116 Australia Prepared By Andy Wana Issue No 01 Ph 02 9638 4744 Fax 02 9638 4822 Authorised By Chris Murty Issue Date 15 5 2013 These instructions remain the property of Rhino Rack Australia Pty Ltd and may not be used or changed for any other purpose than intended Page 1 of 6 Rhino Rack Fairing RF1 RF2 RF3 RF4 When these roof racks are to be used on a vehicle that is driven off sealed roads the manufacturer FTSE 60kg load rating __30kg load rating maximum roof load rating to be fr Urban road Off road 60kg 2 found in the vehicles User Manual o y should be halved Do not forget to subtract 7 5kg from your maximum carrying capacity due
Download Pdf Manuals
Related Search