1000E - Cleveland Time Clock
Contents
1. Rating of AC adapter I P AC 120V 60Hz O P AC 15 0V 1300mA NOTICE Use only the supplied AC adapter 28 MANUFACTURER S WARRANTY Limited One Year Warranty Lathem warrants the model 1000E hardware product against defects in material and workmanship for a period of one year from date of original purchase The conditions of this warranty and the extent of the responsibility of Lathem Time Corporation Lathem under this warranty are listed below 1 This warranty will become void when service performed by anyone other than an approved Lathem warranty service dealer results in damage to the product 2 This warranty does not apply to any product which has been subject to abuse neglect or accident or which has had the serial number altered or removed or which has been connected installed adjusted or repaired other than in accordance with instructions furnished by Lathem 3 This warranty does not cover dealer labor cost for removing and reinstalling the machine for repair or any expendable parts that are readily replaced due to normal use 4 The sole responsibility of Lathem under this warranty shall be limited to repair of this product or replacement thereof at the sole discretion of Lathem 5 If it becomes necessary to send the product or any defective part to Lathem or any authorized service dealer the product must be shipped in its original carton or equivalent fully insured with shipping charges prepaid Lathem2. Siep 3 Change the Date Press the CHANGE button to set at 21 and then press the SET button Step 4 After you finish setting the date press the SET button once again Now the date setting has been completed Replace the cover and lock IMPORTANT If you do not complete Step 4 the clock will not print SETTING THE 12 24 HOUR Example Change the hour format to 24 hour HOUR Step 1 l Press the SELECT button and position the A mark at the HOUR At that moment the flashing digit SELECT CHANGE SET indicates Order Options of the hour format The flashing means it can be changed Order Options Display 12 hour PM 3 00 2 24 hour 15 00 HOUR HOUR a In case of the example press the CHANGE button to set at 2 And then press the SET button SELECT CHANGE SET Step 2 MO TU WE TH FR SA SU a After you finish setting the 12 24 hour 2L110N g the SET button once again ii i g press i IL L Now the 12 24 hour setting has been completed Replace the cover and lock IMPORTANT If you do not complete Step 2 the clock will not print SETTING THE PRINT ORDER Example Change the print order to Month Date Year Hour Minute ORDER Step 1 A 5 V Press the SELECT button and position the n a mark at the PRINT ORDER ES At that moment the flashing d
3. D S T START At that moment the Year flashes The flashing means it can be changed Next press the SET button At that moment the flashing changes from Year to Month Step 2 Press the CHANGE button to set at e e And then press the SET button At that moment the flashing changes from Month to Date Step 3 Press the SET button again At that moment the flashing changes from 25 to ee Step 4 Press the SET button once again Now the D S T deleting has been completed Replace the cover and lock IMPORTANT If you do not complete Step 4 the clock will not print SETTING THE PASSWORD When the password is set you are asked to enter it If the password you entered does not coincide with the setting you cannot change the setting values You may set a password by any 4 digit number from 0001 to 9998 Note a number 0000 and 9999 cannot be used as a password REGISTERING THE PASSWORD Example Set the password 1234 ee NN NN Ul UL vw 7 PASSWORD SELECT CHANGE SET IF 1 nr uu v PASSWORD SELECT CHANGE SET ED IL v PASSWORD SELECT CHANGE SET MO TU WE TH FR SA SU Step 1 Press the SELECT button and position the A mark at the PASSWORD At that moment first two digits flash The flashing means it can be changed In case of the
4. Manual Print direction Print activation Step 1 N K Press the SELECT button and position the a A mark at the PRINT DIRECTION I aba v PRINT ACTIVATION PRINT DIRECTION At that moment the flashing digit at the PRINT ACTIVATION left indicates Order Options of the print SELECT CHANGE SET direction The flashing means it can be changed Change the Print Direction Order Options Right 2 Left Liez In case of the example press the m l CHANGE button to set at 2 And then a press the SET button ana At that moment the flashing changes PRINT DIRECTION from the Print Direction to the Print PRINT ACTIVATION Activation SELECT CHANGE SET 14 Change the Print Activation Step 2 Order Options Automatic 2 Semi automatic 3 Manual eta v PRINT DIRECTION PRINT ACTIVATION SELECT CHANGE SET MO TU WE TH _ FR SA SU A A a 6 0 09 Automatic will allow the clock to print by simply inserting a card or sheet of paper Semi automatic will allow the clock to print by pressing the push bar only when a card or piece of paper is inserted Manual will allow the clock to print by pressing the push bar In case of the example press the CHANGE button to set at 3 And then press the SET b
5. Select desired setting mode by pressing the SELECT button Then make settings as explained CANCELING THE PASSWORD The code 00 00 must be entered to cancel the password Example Cancel the password 1234 99 99 SELECT CHANGE SET N v4 IL y SELECT CHANGE SET i FY SELECT CHANGE SET TIME A es ogo IT n AM d ga 7 SELECT CHANGE SET Step 1 Press the SELECT button at that moment 99 99 is displayed and first two digits flashes The flashing means it can be changed In case of the example press the CHANGE button to set at 12 And then press the SET button At that moment the flashing changes to last two digits Step 2 In case of the example press the CHANGE button to set at 34 And then press the SET button At that moment the a mark indicates the TIME 21 eH ee REE PASSWORD SELECT CHANGE SET N 7 nr J LILI v as PASSWORD SELECT CHANGE SET 2 m LI 3 a m C C C v a Pee PASSWORD SELECT CHANGE SET MO TU WE TH_FR_SA SU mnno c 10 09 22 Step 3 Press the SELECT button and position the amp mark at the PASSWORD At that moment first two digits 12 flashes Th
6. At that moment the flashing changes a from Month to Date SELECT une s SET MO TU WE TH FR su Step 3 qm Change the Date 4 25 Press the CHANGE button to set at 25 And then press the SET button r Step 4 SELECT CHANGE SET ey eee After you finish setting the starting date of x D S T press the SET button once again 2 m n Now the starting date of D S T setting has AM ILI LI been completed Go on to the SETTING THE ENDING DATE OF DAYLIGHT SAVING 16 TIME SETTING THE ENDING DATE OF DAYLIGHT SAVING TIME Example Daylight saving time ends on Sunday October 28 2001 MO TU I TH SU Ar wo a o I w v D S T END SELECT CHANGE SET MO TU WE TH_FR_SA SU LiF i m7 ay t e ap o ap a Z v D S T END SELECT CHANGE SET MO TU WE TH FR SA SU vw x D S T END SELECT CHANGE SET MO TU WE TH FR SU 1 Gi Ww an ILI _ v D S T END SELECT CHANGE SET MO TU WE TH_ FR SA SU A A l Tl 5 Og Step 1 Press the SELECT button and position the a mark at the D S T END At that moment the Year flashes The flashing means it can be changed Change the Year In case of the example press the CHANGE button to set at 01 And then press the SET butto
7. the example press the CHANGE DE button to set at 2 And then press the SET SA7 button l At that moment the flashing changes from Hour to Minute ZOS SELECT CHANGE SET Step 2 Change the Minute Order Options Print Example Order Options Print Example 1 1 60 Min JAN 31 AM12 10 3 1 20 Min 5 100 Min JAN 31 AM12 15 2 1 100 Min JAN 31 AM12 17 4 1 10 Min JAN 31 AM12 1 HOUR MIN A In case of the example press the CHANGE button to set at 2 And then m press the SET button tae SELECT CHANGE SET Step 3 MO TU WE TH FR SA su After you finish setting the hour minute T press the SET button once again 21N AM Now the hour minute setting has been ez I Ly a Ly g completed Replace the cover and lock IMPORTANT If you do not complete Step 3 the clock will not print 10 SETTING THE LEADING ZERO Example Change the leading zero to ZERO Disabled ZERO Step 1 Press the SELECT button and position K the a mark at the LEADING ZERO 71 At that moment the flashing digit SELECT CHANGE SET indicates Order Options of the leading zero The flashing means it can be changed Order Options Print Example ZERO Disabled JAN 1 PM3 00 2 ZERO Enabled JAN 01 PM03 00 LEADING ZERO a In
8. will not assume any responsibility for any loss or damage incurred in shipping 6 WARRANTY DISCLAIMER Limitation of Liability Except in only the limited express warranty set forth above there are no expressed or implied warranties of merchantability and fitness for a particular purpose In no event will Lathem be liable for any direct special or consequential damages arising out of or in connection with the delivery use or inability to use or performance of this product 7 Proof of date of purchase is required for warranty service on this product 8 This Warranty grants specific legal rights Additional legal rights which may vary by locale may also apply 9 Should any difficulties arise with the performance of this product during warranty or with any Lathem authorized service centers contact Lathem Time at the address below Lathem Time Corporation 200 Selig Drive SW Atlanta Georgia 30336 800 241 4990 www lathem com
9. 13 CMPL D A A A A A A A A T a Ea Gl GEE Gl gt Bai li l i li LANGUAGE lt lt gt a lt gt aD 1 ENGLISH l fi fi 2 FRENCH AMPM Gund o Gum 3 SPANISH 4 PORTUGUESE PASSWORD DST BST PANT DIRECTION aor END START PRINT ACTIVATION 2 Lett AEE CG Print Activation IMON iT CC Date LAitomatig SELECT DAYLIGHT SET automatic 5 SAVING 3 Manual TIME D A Control buttons Function of 3 control buttons Program modes SELECT You can select the desired program setting mode by pressing this SELECT button Selected program setting mode is indicated by the a mark on the display CHANGE When you press the CHANGE button you can increment the set value SET You can set the value selected on the display by pressing the SET button Thereafter you press this SET button again you can return the clock to the normal operation mode SETTING THE DISPLAY FORMAT SETTING THE TIME Example Change the time from 10 08 to 10 09 Hour Minute TIME Step 1 45 1 08 SELECT CHANGE SET TIME SELECT CHANGE SET MO TU WE TH_FR_ SA SU ri amp 0 09 Press the SELECT button and position the mark at the TIME At that moment the Hour flashes The flashing means it can be changed Change the Hour In case of the example press the SET button becaus
10. 1OOOE User s Manual Lathem Time Corporation WARNING This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense Caution Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS A LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS AS SET OUT IN THE RADIO INTERFERENCE REGULATIONS OF THE CANADIAN DEPARTMENT OF COMMUNICATIONS LE PRESENT APPAREIL NUMERIQUE N EMET PAS DE BRUITS RADIOELECTRIQUES DEPASSANT LES LIMITES APPLICABLES AUX APPAREILS NUMERIQUES DE CLASSE A PRESCRITES DANS LE REGLEMENT SUR LE BROUILLAGE RADIOELECTRIQUE EDICTE PAR LE MINISTERE DES COMMUNICATIONS DU CANADA 1 The details of this User s Manual are subject to change even without previous notification 2 This User s Manual has be
11. TICE Remove the PROTECTION PAD before you plug the AC adapter into the AC outlet To setup your time clock follow next steps Step 1 Step 2 Unlock the key and remove the cover Remove the PROTECTIONPAD and plug the AC adapter into the time clock Step 4 Plug the AC adapter into the AC outlet and insert a card Replace the cover and lock HOW TO PROGRAM THE CLOCK To enter the program setting mode you should plug the AC adapter into the AC outlet and remove the cover Thereafter press the SELECT button once Then the clock goes into the program mode showing the a on the display positioned at the TIME L C D PRINT ORDER ij A Y Year 1 M D H Min 10 M D Gg M Month 2 0 M H Min 11 DOW D M Y RABBLE D Date 3 M D YH Min 12 C M D Y B DOW Day ofthe week 4 D M Y H Min 13 C D M Y yyy H Hour 5 M D H Min 14 C Y M D Mba Min Minute 6 M D H Min S 15 M D Y C for programming S Second 7 D H Min 16 D M Y C WY yy C Comment 8 DOW D H Min 17 Y M D C G YY 9 M D 18 C D H Min DISPLAY PRINT STYLE AA Sec AA Year 1 12hour 1 2Digits BB Hour 1 ZERO 1 RCVD BB Hour 8B Month 2 24hour 2 4Digits 1 12hour Disabled 2 SENT CC Min CC Date 2 24hour 2 ZERO 3 1N Enabled 4 0UT CC Minute 5 CFMD 1 1 60 6 FILED 2 1 100 7 PAID 3 1 20 8 USED 4 110 9 FAXED PRINT YEAR HOUR LEADING 10 VOID TIME DATE HOUR ORDER DIGIT MIN ZERO COMMENT 11 0RIGN Mol puf we TH FR fsa su 12 APR D
12. case of the example press the CHANGE l button to set at 1 And then press the j SET button SELECT CHANGE SET MO TU WE TH_FR_SA SU Step 2 J l l n m T After you finish setting the leading zero I uu AM ly x Lj press the SET button once again Now the leading zero setting has been completed Replace the cover and lock IMPORTANT If you do not complete Step 2 the clock will not print 11 SETTING THE COMMENT Example Change the comment to SENT COMMENT Step 1 A 7 Se l Press the SELECT button and position the a a mark at the COMMENT 7 At that moment the flashing digits indicate SELECT CHANGE SET Order Options of the comment The flashing means it can be changed Order Options Print Example 1 RCVD JAN 31 01 RCVD 2 SENT JAN 31 01 SENT 3 IN JAN 31 01 IN 4 OUT JAN 31 01 OUT 5 CFMD JAN 31 01 CFMD 6 FILED JAN 31 01 FILED 7 PAID JAN 31 01 PAID 8 USED JAN 31 01 USED 9 FAXED JAN 31 01 FAXED 10 VOID JAN 31 01 VOID 11 ORIGN JAN 31 01 ORIGN 12 APR D JAN 31 01 APR D 13 CMPL D JAN 31 01 CMPL D COMMENT A In case of the example press the CHANGE button to set at 2 And then press the SET pe button _ SELECT CHANGE SET MO TU WE TH FR _SA__SU A IN N gi 10 09 12 Step 2 After you finis
13. e flashing means it can be changed Press the CHANGE button to set at 00 And then press the SET button At that moment the flashing changes to last two digits 34 Step 4 Press the CHANGE button to set at 00 And then press the SET button Step 5 After you finish canceling the password press the SET button once again Now the password canceling has been completed Replace the cover and lock IMPORTANT If you do not complete Step 5 the clock will not print RESETTING To return all setting to the factory defaults push the reset switch with a pointed implement NOTICE All your custom settings will be deleted and will revert to the factory defaults when the reset switch is pushed To make new settings please refer to SETTING Reset switch 23 WALL MOUNTING Caution The supplied screws are intended for use on a thick wooden wall or wooden column Do not use them on any other materials The time clock may come off if used on other materials Step 1 Install the supplied wall mount screws into a wall by using the template 9 cm tt by 5 cm apart Be sure to keep about 6 mm of the screw head away from the wall WALL Upper side Step 2 Unlock the key and remove the cover And then hang it on the wall Step 3 Replace the cover and lock 24 REPLACING THE RIBBON CASSETTE Step 1 Unlock the key and remove the cover Step 2 Pick up the cassette and rem
14. e the hour is not to be changed At that moment the flashing changes from Hour to Minute Step 2 Change the Minute Press the CHANGE button to set at 09 and then press the SET button At that moment the Second starts to run from 00 Siep 3 After you finish setting the time press the SET button once again Now the time setting has been completed Replace the cover and lock IMPORTANT If you do not complete Step 3 the clock will not print SETTING THE DATE Example Change the date from October 20 2001 to October 21 2001 Year Month Date DATE a A m i orig 20 SELECT CHANGE SET DATE A gron IUC z SELECT CHANGE SET 7 SELECT CHANGE SET DATE A SELECT CHANGE SET MO TU WE TH_FR_ SA SU m 6 0 09 C3 Step 1 Press the SELECT button and position the a mark at the DATE At that moment the Year flashes The flashing means it can be changed Change the Year In case of the example press the SET button because the year 2001 is not to be changed At that moment the flashing changes from Year to Month Step 2 Change the Month In case of the example press the SET button because the month is not to be changed At that moment the flashing changes from Month to Date
15. en prepared with the utmost care to cover all aspects of the time clock s use 3 Be sure to use your time clock after you have fully understood the hardware and software specifications and limits 4 No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means mechanical photocopying recording or otherwise This User s Manual and its contents are copyrighted by LATHEM TIME CORP with all rights reserved Lathem Time Corporation www lathem com 800 241 4990 Thank you for purchasing our time clock For safe and proper operation please carefully read the manual before using the time clock and save it for reference F eatu res Main applications Payroll job cost recorder or time stamp e Quartz time clock gt e12 or 24 hour format e Dot matrix printer Regular minute 1 10 1 60 e Perpetual calendar 1 100 or 5 100 of an hour e Automatic daylight saving time e2 or 4 digit year imprint e 3 way print activation e13 preprogramed comments Automatic Digital LCD display Date Hour Semi automatic Minute Day of the week indication Manual eAdjustable print position e Prints in 4 languages ePrints seconds Cave Avoid placing the unit in environments that are e humid or dusty exposed to direct sunshine e subject to frequent or continuous vibrations e outside the temperature range between 5 and 45 C 25 and 113 F e affected by chemical
16. example press the CHANGE button to set at 12 And then press the SET button At that moment the flashing changes to last two digits Step 2 In case of the example press the CHANGE button to set at 34 And then press the SET button Step 3 After you finish registering the password press the SET button once again Now the password registering has been completed Replace the cover and lock IMPORTANT If you do not complete Step 3 the clock will not print 19 HOW TO CHANGE SETTING WHEN THE PASSWORD IS SET Once the password is set you have to enter the password for changing any setting 99 99 will be displayed when you press the SELECT button before entering Example Password 1234 99 99 SELECT CHANGE SET l Z 7 N SELECT CHANGE SET i FY SELECT CHANGE SET SELECT CHANGE SET 20 Step 1 Press the SELECT button at that moment 99 99 is displayed and first two digits flashes The flashing means it can be changed In the example press the CHANGE button to set at 12 And then press the SET button At that moment the flashing changes to last two digits Step 2 In case of the example press the CHANGE button to set at 34 And then press the SET button At that moment the mark indicates the TIME Step 3
17. h setting the comment press the SET button once again Now the comment setting has been completed Replace the cover and lock IMPORTANT If you do not complete Step 2 the clock will not print SETTING THE LANGUAGE This setting is available if you select Month Day of the week or Comment in previous PRINT ORDER Example Change the print language into French SY _ taneuace Step 1 Press the SELECT button and position the a mark at the LANGUAGE At that moment the flashing digit Aud r x SEET ORANGE TEET indicates Order Options of the print language The flashing means it can be changed Order Options Print Example WE 26 DEC 01 1 ENGLISH OUT 31 AM10 00 ME 26 DEC 01 2 FRENCH SORT 31 AM10 00 MI 26 DIC 01 3 SPANISH SAL 31 AM10 00 4 PORTUGUESE SA E DEAU SAIDA 31 AM10 00 In case of the example press the pa gt tancuace CHANGE button to set at 2 And then press the SET button SELECT CHANGE SET MO TU WE TH_FR_ SA SU mna E 10 89 Step 2 After you finish setting the language press the SET button once again Now the language setting has been completed Replace the cover and lock IMPORTANT If you do not complete Step 2 the clock will not print 13 SETTING THE PRINT METHOD Example Change the print direction to Left and the print activation to
18. igits indicate SELECT CHANGE SET Order Options of the print order The flashing means it can be changed Y Year M Month D Date DOW Day of the week H Hour Min Minute S Second C Comment Order Option Print Example l M D H Min JAN 31 AM10 00 2 D M H Min 31 JAN AM10 00 3 M D Y H Min JAN 31 01 AM10 00 4 D M Y H Min 31 JAN 01 AM10 00 PE Y M D H Min 01 JAN 31 AM10 00 6 Y M D H Min S 01 JAN 31 AM 10 00 00 7 D H Min 31 AM10 00 8 DOW D H Min WE 31 AM10 00 9 Y M D 01 JAN 31 10 M D JAN 31 11 DOW D M Y WE 31 JAN 01 12 C M D Y SENT JAN 31 01 13 C D M Y SENT 31 JAN 01 14 C Y M D SENT 01 JAN 31 15 M D Y C JAN 31 01 SENT 16 D M Y C 31 JAN 01 SENT 17 Y M D C 01 JAN 31 SENT 18 C D H Min SENT 31 AM10 00 PRINT ORDER a In case of the example press the CHANGE button to set at 3 And then press the SET button SELECT CHANGE SET Step 2 MO TU WE TH FR SA SU a After you finish setting the print order ce m q press the SET button once again AM i Lj Now the print order setting has been completed Replace the cover and lock IMPORTANT If you do not complete Step 2 the clock will not print SETTING THE PRINT STYLE SETTING THE YEAR DIGIT Example Change the year imprint to 4 digits bic S
19. ing mistake Make sure the correct starting and ending date of daylight saving time and enter again E 49 Setting data you entered is not usable Refer to your owner s manual on the page related to the item you want to set and enter again correct setting data OTHER FAILURES The time clock does not operate Ensure the AC adapter is properly plugged into the AC outlet The time clock does not print Ensure the ribbon is installed correctly The card is jammed Press the push bar and try to pull out the card at the same time 27 SPECIFICATIONS Clock accuracy Monthly accuracy 15sec at ordinary temperatures Calendar Year up to 2099 Automatically adjusted to leap years 31 day months and months with thirty or fewer days and the days of the week Printing system Dot matrix imprint Power failure Five years of cumulative power failure hours after the date of shipment compensation Temperature 5 to 45 C 25 to 113 F f Humidity 20 to 80 no condensation Operating F P nvironment The unit operates normally at temperatures of 5 C or below but the print i density reaction of the liquid crystal display and the number of prints at power failure are inferior to those at normal temperature operation Dimension 160 w x 143 h x 172 d mm 6 3 w x 5 63 h x 6 77 d Weight Approx 1 4 kg 2 0 kg with AC adapter Power consumption Approx 13W AC120V 10 60Hz
20. n At that moment the flashing changes from Year to Month Step 2 Change the Month Press the CHANGE button to set at 10 And then press the SET button At that moment the flashing changes from Month to Date Step 3 Change the Date Press the CHANGE button to set at 28 And then press the SET button Step 4 After you finish setting the ending date of D S T press the SET button once again Now the ending date of D S T setting has been completed Replace the cover and lock IMPORTANT If you do not complete Step 4 the clock will not print 17 DELETING THE DAYLIGHT SAVING TIME SETTING To delete and cancel the daylight saving time setting change the display of Month of the starting setting to Example Change March 25 2001 of D S T START and delete daylight saving time setting MO TU y TH A x val ie 25 7 N DST START SELECT CHANGE SET MO TU WE__TH FR SA SU Neal a ni A Li i l 5 x Ne v D S T START SELECT CHANGE SET MO TU WE TH FR_ SA SU y 5 DST START SELECT CHANGE SET MO TU WE TH FR_ SA SU I ml ay I o ap o ap lt 4 v DST START SELECT CHANGE SET MO TU WE TH _ FR SA SU a TI amp 0 09 18 Step 1 Press the SELECT button and position the a mark at the
21. ove it Step 3 Turn the knob of the new cassette in the direction of the arrow to tighten the ribbon Step 4 Place the cassette inside the time clock as shown in the figure Keep on pushing in the cassette until the clasps at both sides catch and you hear a pop sound If it is difficult to insert the cassette try it while turning the knob 25 26 Print head NOTICE Install the cassette so that the ribbon is between the print head and the ribbon mask Printing will not come out properly if the ribbon is placed behind the ribbon mask Ribbon mask Ribbon Step 5 Turn the knob of the cassette in the direction of the arrow to tighten the ribbon Step 6 Replace the cover and lock TROUBLESHOOTING ERROR No APPEARS Refer to the following list for proper operation No Error contents Action E 00 CPU error Contact the store from whom you bought the Time Clock call Lathem Time directly E 01 The remaining life of lithium battery for at 800 241 4990 memory back up is short E 05 The card is not inserted in the clock properly Correctly insert the card E 30 Cannot print Make sure that the ribbon cassette is The printer motor or home position sensor correctly inserted in place is not normal E 38 Cannot print Press the push bar The print head motor or the sensor does not operate properly E 40 Incorrect password Enter the correct password again E 41 D S T sett
22. s or ozone Place the time clock close to the wall outlet so that it is easily accessible to disconnect Do not put a heavy object on the clock or not forcefully press the cover of the clock It may cause mechanism trouble and danger especially when the unit is hung on the wall Replace battery with TOSHIBA part no CR 2450 TVB only Use of another battery may present a risk of fire or explosion For questions about the operation of this time clock or to order supplies and accessories please contact Lathem Time at 800 241 4990 BEFORE USING THE TIME CLOCK Accessories ral User s manual Key Configuration lt Front view gt Cover Key hole Push bar lt Print position adjuster gt The print position from the card edge is adjustable by pressing and sliding the print position button on outside bottom QO Q e WWOS 00 2L Y LE NYE es gt 2z a f N li S i WG WLENWE AC adapter o7 OF 6 6 6 Ribbon cassette Wall mount fittings installed at the factory Screws 2 pcs Template lt Cover off gt Ribbon cassette Wall mount holes Upper side PRINT POSITION ON TIME CARD The print position from the card edge is adjustable by pressing 1 and sliding the print position button located on the right outside bottom of the recorder Maxuim distance from edge of form to print is approximately 1 3 16 30mm QUICK EASY SETUP NO
23. tep 1 Press the SELECT button and position the a mark at the YEAR DIGIT Ay S At that moment the flashing digit SELECT CHANGE SET indicates Order Options of the year imprint The flashing means it can be changed Order Options Print Example 2 Digits JAN 31 01 AM10 00 Di 4 Digits JAN 31 2001 AM10 00 YEAR DIGIT A In case of the example press the CHANGE j button to set at 2 and then press the SET ER button SELECT CHANGE SET Step 2 MO TU WE TH_FR_ SA SU After you finish setting the year digit A Pad l f c M g press the SET button once again am OLS US AM Now the year digit setting has been completed Replace the cover and lock IMPORTANT If you do not complete Step 2 the clock will not print SETTING THE HOUR MIN Example Change the print style of the Hour and Minute to 24 hour and 1 100 min Type of Type of S Cee MINE Minute tep 1 ee Press the SELECT button and position the oo a mark at the HOUR MIN j At that moment the flashing digit at the AN left indicates Order Options of the print SELECT CHANGE SET style of the Hour The flashing means it can be changed Change the Hour Order Options Print Example 1 12 Hour JAN 31 PM3 00 2 24 Hour JAN 31 15 00 HONA In case of
24. utton Step 3 After you finish setting the print method press the SET button once again Now the print method setting has been completed Replace the cover and lock IMPORTANT If you do not complete Step 3 the clock will not print Push bar 15 SETTING THE DAYLIGHT SAVING TIME Example Start date Sunday March 25 2001 End date Sunday October 28 2001 If you set as the above the time clock remembers the start date as the last Sunday of March and the end date as the last Sunday of October Once set the time clock automatically updates the settings every year thereafter No further manual setting is necessary SETTING THE STARTING DATE OF DAYLIGHT SAVING TIME Example Daylight saving time starts on Sunday March 25 2001 er ea Step 1 p SETETE Press the SELECT button and position A the a mark at the D S T START v At that moment the Year flashes DST The flashing means it can be changed START SELECT CHANGE SET Change the Year MO ATU WE TH _FR__SA__SU In case of the example press the m y So Uo CHANGE button to set at 01 And then LI tw oe press the SET button 4 At that moment the flashing changes 7 from Year to Month SELECT CHANGE SET MO TU WE TH FER SA SU Step 2 I a Change the Month g i 4 eae eee Press the CHANGE button to set at 3 And then press the SET button ies dee
Download Pdf Manuals
Related Search