24-P + 2-SFP Gigabit Ethernet Switch User Manual V1.0
Contents
1. Interface 24x10 100 1000Mbps RJ 45 ports 2xMini GBIC open slots 1x IEEE802 3az push button Cable Connections RJ 45 10BASE T Category 3 4 5 UTP STP RJ 45 100BASE TX Category 5 UTP STP RJ 45 1000BASE T Category 5e 6 UTP STP Fiber depend on Mini GBIC types Network Data Rate 10 100 1000 Mbps Auto negotiation Transmission Mode 10 100Mbps Full duplex Half duplex 1000Mbps Full duplex LED System Power Indications Ports Link ACT 8K MAC entries Memory 4 1M bit buffer memory Jumbo Frame 10K bytes Temperature Operating 0 50 C 32 122 F Humidity Operating 10 90 non condensing Power Supply Internal power supply EMC FCC CE Class A Safety LVD EN60950 1 102. 24 P 2 SFP Gigabit Ethernet Switch User Manual V1 0 FCC Certifications FC This Equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CE Mark Warning This equipment complies with the requirements relating to the EMC Directive 2004 108 EC the Low Voltage Directive 2006 95 EC and the RoHS Directive 2011 65 EU Company has an on going policy of upgrading its products and it may be possible that information in this document is not up to date Please check with your local distributors for the latest information No part of this document can be
3. can change transceivers while the switch is operating and wuse different transceivers to connect to Ethernet switches with different types of fiber optic or even copper cable connectors The SFP modules is a hot pluggable transceiver and specified by a multi source agreement MSA See the SFF committee s INF 8074i specification Rev 1 0 for details 802 3az ON OFF button The IEEE802 3az ON OFF button helps reducing the power consumption of switch This button allows users to keep the best performance without transmission impacted or to have the green support of Energy Efficient Ethernet mode with the simple push of a button Rear Panel The three pronged power receptacle is located on the rear panel of the switch The rear panel of the switch is shown as below Power Receptacle To be compatible with the electric service standards around the world the switch is designed to afford the power supply in the range from 100 to 240VAC 50 60Hz Please make sure that your outlet standard to be within this range To power on the switch connect one end of the supplied power cord to the power receptacle on the back of the switch and the other end to the appropriate power source After the power cord installation please check if the power LED is illuminated for a normal power status 6 Installation This switch can be placed on your desktop directly or mounted in a rack The install
4. copied or reproduced in any form without written consent from the company Trademarks All trade names and trademarks are the properties of their respective companies Copyright 2014 All Rights Reserved Unpacking Information Thank you for purchasing this product Before installation please verify that your package contains the following items 1 One 24 Port Gigabit Ethernet switch with 2 SFP ports 2 One AC power cord 3 Rack mount bracket x2 4 Rubber foot x4 and screws 5 One user manual Introduction Easily boost your networking throughput the rack mountable switch provides you 24 10 100 1000Mbps ports that lead you to a real Gigabit connection Users are now able to transfer large and high bandwidth needed files faster and hence get a real efficiency improvement In addition to the cooper ports 2 ports support fiber connection with the 2 equipped Mini GBIC ports for obtaining long distance communication The switch offers users with fast and reliable network The store and forward architecture filters errors and forwards packets in a non blocking environment Flow control ensures the correctness of data transmitting The 802 3x and backpressure flow control mechanisms work respectively for full and half duplex modes The switch features with easy installation and maintenance It supports N Way auto negotiation protocol which detects the networking speed either 10 100 1
5. 000 Mbps and the duplex modes Full or Half duplex mode automatically and do an immediately adjustment to advance the capability and performance Auto MDI MDI X function alleviates the effort to use crossover cables Users need not to prepare crossover cables for equipment connectivity Also rich diagnostic LEDs are provided for users to get real time information of the connection status that helps to do quick response and correction Key Feature Complies with 10BASE T specifications of the IEEE802 3 standard Complies with 100BASE TX specifications of the IEEE802 3u standard Complies with 1000BASE T specifications of the IEEE802 3ab standard Complies with 1000BASE X specifications of the IEEE802 3z standard Complies with IEEE802 3az Energy Efficient Ethernet Complies with IEEE 802 1p Cos Supports back pressure half duplex and flow control IEEE 802 3x Supports N Way protocol for speed 10 100 1000Mbps and duplex mode Half Full auto detection Supports MDI MDI X auto crossover and polarity correction Store and forward architecture filters fragment amp CRC error packets Push on off button to enable disable IEEE802 3az Provides 2 SFP ports for optional fiber connection Supports 8K entries MAC address Support 4 1M bit buffer memory Support 10K bytes jumbo frames Supports extensive LED indicators for network diagnostics Rack mountable Internal power supply 100 24
6. 0V AC 50 60Hz universal input EMC FCC CE Class A Safety LVD EN60950 1 Front Panel The front panel of the switch contains the RJ45 ports LEDs 2 SFP ports and an IEEE802 3az EEE ON OFF button For detailed LED definition please refer to the next paragraph The front panel of the switch is shown as below LEDs Definition This switch contains one power LED and Link Act LEDs that shows the activities and information of the ports LED Status Operation Steady Green The switch is powered on Power Off The switch is powered off Steady Green Valid port connection Link Valid port connection and AT Blinking Green there is data transmitting receiving off Port disconnected RJ 45 Ports All the RJ 45 ports in the device are auto negotiating and auto crossover An auto negotiating port can detect and adjust to the optimum Ethernet speed 10 100 1000 Mbps and duplex mode full duplex or half duplex of the connected device An auto crossover auto MDI MDI X port automatically works with a straight through or crossover Ethernet cable Mini GBIC Slots There are two slots for mini GBIC Gigabit Interface Converter transceivers You can plug the SFP port modules into the switch The SPF port modules are to be used with fiber optical transceiver cabling in order to uplink various other networking devices for a gigabit link that may span great distances You
7. ation is a snap Users can use all the features of the switch with simply attaching the cables and turning the power on Before installing the switch we strongly recommend 1 The switch is placed with appropriate ventilation environment A minimum 25mm space around the unit is recommended 2 The switch and the relevant components are away from sources of electrical noise such as radios transmitters and broadband amplifiers 3 The switch is away from environments beyond recommend moisture Desktop Installation 1 Attach the provided rubber feet to the bottom of the switch to keep the switch from slipping The recommend position has been square marked 2 Install the switch on a level surface that can support the weight of the unit and the relevant components 3 Plug the switch with the female end of the provided power cord and plug the male end to the power outlet Rack mount Installation The switch may standalone or may be mounted in a standard 19 rack Rack mounting produces an orderly installation when you have a number of related network devices The switch is supplied with two optional rack mounting brackets and screws which are used for rack mounting the unit Rack mount Installation Requirements 1 Two mounting brackets 2 Six M3 flat head screws Procedures to Rack Mount the switch in the rack 1 First disconnect all the cables from the switch 2 Place the unit the right w
8. ay up on a hard flat surface with the front facing you 3 Locate a mounting bracket over the mounting holes on one side of the unit 4 Insert the screws and fully tighten with a suitable screwdriver 5 Repeat the two previous steps for the other side of the unit 6 Insert the unit into the rack with suitable screws 7 Reconnect all the cables Network Cables 1 Crossover or straight through cable All the ports on the switch support Auto MDI MDI X functionality Both straight through or crossover cables can be used to connect the switch with PCs as well as other devices like switches hubs or router 2 Category 3 4 5 5e 6 UTP STP cable To make a valid connection and obtain the optimal performance Appropriate cables corresponding to different transmitting receiving speed is required To choose a suitable cable please refer to the following table Media aes Wiring 10 Category3 4 5 UTP STP 10 100 1000 Mbps 100 Category 5 UTP STP copper 1000 Category5e 6 UTP STP The cable type differs 1000Mbps from the nin CBIC you Fiber Mini GBIC 1000 purchase Please refer to required the instruction that came with your mini GBIC Product Specifications Standard IEEE802 3 10BASE T IEEE802 3u 100BASE TX IEEE802 3ab 1000BASE T IEEE 802 3z 1000Base xX IEEE802 3x full duplex flow control IEEE 802 3az Energy Efficient Ethernet IEEE 802 1p Cos
Download Pdf Manuals
Related Search