10/100Base-TX to 100Base-FX Fast Ethernet Converter Module
Contents
1. 00Base TX to 100Base FX Converter Module Bidi SC Single Mode 40Km 1310nm MFCR100B55 60 10 100Base TX to 100Base FX Converter Module Bidi SC Single Mode 60Km 1550nm MFCR100BS3 60 10 100Base TX to 100Base FX Converter Module Bidi SC Single Mode 60Km 1310nm Model Description 10 100Base TX to 100Base FX MECRIOOSC Converter Module SC Multi Mode 10 100Base TX to 100Base FX MFCRIOOST Converter Module ST Multi Mode 1 4 DIP Switch Setting Converter AUTO FORCE selectable Bit 1 of S1 TP Port a AUTO 10 100 Nway default 100TP b FORCE 100 FDX LFP TP FORCE ON SI AA TP AUTO LFP OFF Fig 2 S1 Bit 1 2 Configuration and Setting S1 1 TP port mode AUTO default or FORCE S1 2 LFP function LFP OFF default or ON 5 Installing the Converter Note Converter modules are hot swappable Wear a grounding device for electrostatic discharge Unscrew and remove the cover plate from the converter chassis Verify the converter module is the right model and conforms to the chassis slot gt Slide the module along the two guides in the slot and fasten the thumb knob be sure the converter module is properly seated on the slot socket connector gt Install the media cable for network connection gt Repeat the above steps as needed for each module to be installed into slot s Fibre Port TP Port Defaul2. 10 100Base TX to 100Base FX Fast Ethernet Converter Module User s Manual 620 123 1 000 1 Overview The MFCR100 Series is designed to convert between 10 100Base TX and 100Base FX Fibre Ethernet The converter module is designed to be installed into the MCR12 Managed Media Converter Chassis 2 Checklist Before you start installing the Converter verify that the package contains the following The TP Fibre Converter Module This User s Manual Please notify your sales representative immediately if any of the aforementioned items is missing or damaged Fig 1 Converter Module Front Panel 3 Model Description MFCR1O00SC 05 10 100Base TX to 100Base FX Converter Module SC Single Mode 5Km MFCR100SC 20 10 100Base TX to 100Base FX Converter Module SC Single Mode 20Km Converter LFP function selectable Bit 2 of S1 LFP a LFP function OFF default Function b LFP function ON MFCR100SC 40 10 100Base TX to 100Base FX Converter Module SC Single Mode 40Km MFCR100SC 60 10 100Base TX to 100Base FX Converter Module SC Single Mode 60Km MFCR100B55 20 10 100Base TX to 100Base FX Converter Module Bidi SC Single Mode 20Km 1550nm MFCR100BS3 20 10 100Base TX to 100Base FX Converter Module Bidi SC Single Mode 20Km 1310nm MFCR100B55 40 10 100Base TX to 100Base FX Converter Module Bidi SC Single Mode 40Km 1550nm MFCR1O00BS3 40 10 1
3. Fiber Technical Specifications e Standards EEE802 3u 10 100Base TX 100Base FX e Management Support remote access remote monitor and loopback test functions through TS 1000 specification e UTP Cable Cat 5 cable and above up to 100m e Fibre Cable 9 125 yam single mode 2 62 5 125am 50 1254 multi mode LED Indicators PWR FX LINK ACT TP LINK ACT SPEED Data Transfer Rate Speed Forwarding Rate 100Mbps 148 800 PPS 1OMbps 14 880 PPS e TP 10 100FDX HDX with NWay auto negotiation Fibre 100FDX HDX e Power Requirement 0 464 3 3VDC e Ambient Temperature 0 to 40 C e Humidity 5 to 90 e PCB Dimensions 86 L 60 W mm 11 TS 1000 TS 1000 function performs the loopback test between central and remote converter the indication frames would inform its status when central or remote side has any change Note The TS 1000 function will be performed entirely only when the central and remote TS 1000 converters are supplied by the same vender
4. t 100FDX Attach the fibre cable The Tx Rx fibre cable must be paired at both ends Attach TP cable to TP port Mode 10 100Mbps with NWay 6 Link Fault Pass Through Link Fault Pass Through allows the link fault of one device to be passed through to the connecting device If the copper or fibre port of one converter fails then both the copper and fibre ports on the connecting media converter will also fail This can be used as a means of determining network faults 7 LED Description LED Color Function POWER G FX LINK ACT G TP LINK ACT Gi Lit when fibre connection is good Blinks when any traffic is present Lit when TP connection is good Blinks when any traffic is present N Lit when 100Base TX is active TP SPEED OFF when 10Base T is active TS 1000 100FX Fibre Network 100Mbps NWay TP Network Fig 3 Fast Ethernet Converter Network Connection 1 Lit when 5V power is coming up 10 100Mbps NWay 10 100Mbps NWay TP Network TP Network TS 1000 TS 1000 10 100 TP to 100 FX 10 100 TP to 100 FX 1310 nm Single Fiber TX 1310 nm RX 1550 nm n lt gt RX 1550 nm Fig 4 Fast Ethernet Converter Network Connection 2 8 Cable Connection Parameter TP Cable Limitations Cat 5 and above up to 100m Fibre Cable Limitations Single mode fibre 9 125um and up to 60Km Multi mode fibre 62 5 125um 50 125um and up to 2Km 10 TP
Download Pdf Manuals
Related Search