Fusion 150 - Prolight Concepts
Contents
1. 0000 www prolight co uk Fusion 150 User Manual 3 EQUINOX Technical specifications O1 LED display O5 Enter button 09 DMX in In the box 1 x fixture 02 Menu button 06 Power out socket 10 On off switch PA bag amp 03 Down button 07 Power in socket 11 DMX out 1x user manual 04 Up button 08 Fuse 5A 250V www prolight co uk Fusion 150 User Manual 4 EQUINOX Operating instructions DMX channel selection Operating in DMX control mode gives the user the greatest flexibility when it comes to customising or creating a show In this mode you will be able to control each individual trait of the fixture and each fixture independently To access the DMX channel mode press the MODE button on the font of the unit to show LHnd on the LED display Now press the ENTER button and the channel mode will be displayed Use the UP and DOWN buttons to choose one of the 1 4 7 or 10 DMX channel modes Press the ENTER button again this will set the DMX channel The display will now display Addr To exit out of any of the above options press the MODE button 1 channel mode 1 Blackout 8 127 Auto run ATO1 128 255 Sound active 128 low sensitivity 255 high sensitivity www prolight co uk Fusion 150 User Manual 5 EQUINOX 4 channel mode 2 fo 2 fo ra GN EE C Blackout 201 255 255 erme 201 slow TN 255 fast Te 7 channel mod2. EQUINOX Fusion 150 12 x 12W Moving Head User Manual Order code EQLEDOO5 EQU NOX Safety advice WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP e Before your initial start up please make sure that there is no damage caused during transportation e Should there be any damage consult your dealer and do not use the equipment e To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual e Please note that damages caused by user modifications to this equipment are not subject to warranty CAUTION CAUTION TAKE CARE USING KEEP THIS EQUIPMENT THIS EQUIPMENT AWAY FROM RAIN MOISTURE AND LIQUIDS HIGH VOLTAGE RISK OF ELECTRIC SHOCK IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment e Never let the power cable come into contact with other If the equipment is dropped or damaged disconnect the cables Handle the power cable and all mains voltage mains power supply immediately and have a qualified connections with particular caution engineer inspect the equipment before operating again e Never remove warning or informative labels from the unit If the equipment has been exposed to drastic Do not open the equipme
3. XLR socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal 5 pin XLR socket 3 pin XLR socket Pin 1 GND screen Pin 1 GND screen 0 5 Pin 2 Signal Pin 2 Signal Pin 3 Signal Pin 3 Signal Pin 4 N C Pin 5 N C www prolight co uk Fusion 150 User Manual 10 EQUINOX WEEE notice Correct Disposal of this Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries SS with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed of with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal CE f www prolight co uk Fusion 150 User Manual 11 EQUINOX www prolight co uk Fusion 150 User Manual 12
4. correct operation may lead to danger e g short circuit burns and electric shocks etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and or property www prolight co uk Fusion 150 User Manual 2 EQUINOX Product overview amp technical specifications Fusion 150 Housing 12 x 12W quad colour LEDs the Equinox Fusion 150 moving head wash gives smooth colour mixing from rich saturated hues to subtle pastel shades The compact and lightweight design allows for easy transportation and installation The 4 push button LED menu allows for easy access to the functions including DMX auto sound active and master slave modes Loaded with advanced internal programming by Equinox the sound active and auto modes deliver stunning light shows e 12 x 12W quad colour LEDs e Beam angle 40 e Pan 540 Tilt 180 e DMX channels 1 4 7 or 10 selectable Auto sound active strobe and master slave modes e 0 100 dimming e 4 push button menu with LED display e IEC in out sockets e 3 pin XLR in out socket e Fan cooled e Supplied with hanging bracket Tema 0000 45 Lux 850 280 100 40 16 Specifications Fusion 150 Power consumption 180W u SEN Power supply 100 240V 50 60Hz ed EEE Dimensions 288 x 222 x 190mm ee M ee Weight 3 6kg Order code EQLED005 Om im 2m 3m 4m 5m 222mm 190mm NE WW88C
5. e Function 0 255 Pan adjustment 0 255 Tilt adjustment 0 255 0 100 dimming 0 low brightness 255 high brightness 0 255 Green 0 low brightness 255 high brightness 0 255 Blue 0 low brightness 255 high brightness 0 255 White 0 low brightness 255 high brightness a 0 255 Red 0 low brightness 255 high brightness www prolight co uk Fusion 150 User Manual 6 EQUINOX Operating instructions 10 channel mode 0 255 Red 0 low brightness 255 high brightness 0 255 Green 0 low brightness 255 high brightness 0 255 White 0 low brightness 255 high brightness lu a lo 2 lo 8 lo 4 jo 514 fred o O 45 54 cyan ite ite ite ite Pastle red red amp white Colour change 201 slow change 255 fast change 0 255 0 100 dimming 0 low brightness 255 high brightness 95 104 Pastle green green amp white hi i i Changing the address To access the address menu press the MODE button on the front of the unit to show Ad dr is displayed Press the ENTER button the unit should now display HUG 1 Use the UP and DOWN buttons to select AOO through AS IZ Press the ENTER button again this will set the address To exit out of any of the above options press the MODE button www prolight co uk Fusion 150 User Manual 7 EQUINOX Operating instructions Slave mode To access slave mode press MODE until the displa
6. hoose between LO I EL 15 orF Ade When using the F Ad E function press the ENTER button and use the UP and DOWN buttons to select the desired fade speed between SFO 1 5F4 I Press the ENTER button to confirm the setting To exit out of any of the above options press the MODE button Other settings PAn X motor positive negative move set bil E Y motor positive invert move set I Ed digital display ON OFF set d SP digital display invert EH P5k function test Hatir total fixture run time PF r SEE reset www prolight co uk Fusion 150 User Manual 8 EQUINOX DMX setup Setting the DMX address The DMX mode enables the use of a universal DMX controller Each fixture requires a start address from 1 511 A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address For example a fixture that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 100 would read data from channels 100 101 102 103 104 105 and 106 Choose a start address so that the channels used do not overlap E g the next unit in the chain starts at 107 DMX 512 DMX Digital Multiplex is a universal protocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions form the controller to the fixture DMX data is sent as serial data that travels from fixture to fi
7. nt and do not modify the unit temperature fluctuation e g after transportation do not connect power or switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature Do not connect this equipment to a dimmer pack e Do not switch the equipment on and off in short intervals as this will reduce the system s life e Only use the equipment indoors If your product fails to function correctly stop use Do not expose to flammable sources liquids or gases immediately Pack the unit securely preferably in the e Always disconnect the power from the mains when original packing material and return it to your Pro Light equipment is not in use or before cleaning Only handle dealer for service the power cable by the plug Never pull out the plug by pulling the power cable Repairs servicing and power connection must only be e Make sure that the available voltage is between carried out by a qualified technician THIS UNIT CONTAINS 100 240V 50 60Hz NO USER SERVICEABLE PARTS e Make sure that the power cable is never crimped or WARRANTY One year from date of purchase damaged Check the equipment and the power cable periodically Only use fuses of same type and rating OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void In
8. ure to follow the diagrams below when making your own cables Do not connect the cables shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs outer casing Grounding the shield could cause a short circuit and erratic behaviour common DMX 512 out DMX 512 in 3 pin XLR 3 pin XLR KEN ED ee KE XLR MALE SOCKET XLR FEMALE SOCKET XLR Pin Configuration 2 cold 1 ground 1 ground 2 cold Pin 1 Ground Q Pin 2 Negative 3Hot 3Hot Pin 3 Postive Special note Line termination When longer runs of cable are used Termination reduces signal transmission you may need to use a terminator on problems and interference It is always the last unit to avoid erratic behaviour advisable to connect a DMX terminal resistance 120 Ohm 1 4 W between pin 2 Using a cable terminator will decrease DMX and pin 3 DMX of the last fixture the possibilities of erratic behaviour 3 pin Order ref CABL90 5 pin Order ref CABL89 S pin XLR DMX connectors Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used The diagram below details the correct cable conversion F B A gt 5 pin XLR socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal Pin 4 N C Pin 5 N C 3 pin
9. xture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a data out terminal DMX linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain DATA cable DMX cable requirements for DMX operation This fixture can be controlled via DMX 512 protocol The DMX address is set on the back of the unit Your unit and your DMX controller require a standard 3 pin XLR connector for data input output see image below Further DMX cables can be purchased from all good sound and lighting suppliers or Pro Light Concepts dealers Please quote CABL10 2m CABL11 5m CABL12 10m Note DMX cable must be daisy chained and cannot be split www prolight co uk Fusion 150 User Manual 9 EQUINOX DMX setup Notice Be s
10. y shows 5L nd Press the ENTER button the unit should now display 5L Use the UP and DOWN buttons to select either SL f orSL Press the ENTER button again this will enable your chosen slave mode To exit out of any of the above options press the MODE button Adjusting the sound sensitivity To access the sound sensitivity menu press MODE until the display shows SaLin Press the ENTER button the unit should now display the sensitivity in three digits Use the UP and DOWN buttons to select OG I through IOD Press the ENTER button again this will set the sound sensitivity To exit out of any of the above options press the MODE button Auto mode To access auto mode press MODE until the display shows Hut o Press the ENTER button The unit will now display HE 1 Use the UP and DOWN buttons to select either AE D 1 or Sou I Press the ENTER button again this will enable your chosen auto mode To exit out of any of the above options press the MODE button Please ensure that all slave units are set to the same DMX channel mode as the master unit Static colour mode to use the fixture as an uplighter To access static colour mode press MODE until the display shows Hut a Press the ENTER button and use the UP and DOWN buttons to select either 54 AE Press the ENTER button again this will enable you to c
Download Pdf Manuals
Related Search