/X11C X11 - RC Helicopters
Contents
1. MAIN PARAMETER Length of fuselage 152mm Width of fuselage 152mm Height of fuselage 37mm Battery 3 7V 200mAh Code of main engine 6X15 coreless motor VERIFIED SPECIFICATIONS AND COLORS OF CONTENTS MAY VARY FROM PHOTO The company has the right of final interpretation of this instruction manual statement 112. it by pressing under top fine tuning button When the quad copter keeps flying to left right side you can correct it by pressing the right left fine tuning button When the quad copter keeps rotating to left right you can correct it by pressing the left right fine tuning button FLIGHT CONTROL Low Speed Press the High Low speed switch for one time the buzz will send out one sound High Speed Please press High Low speed switch once again the buzz will send out two sounds 3D EVERSION AND THROWING FLIGHT INSTRUCTIONS 1 When you are familiar with the basic operation you can play some awesome amp thrilling stunt operation 2 First of all fly the four axial aircraft CIS Cup to the height of more than 3 meters 224 2 a press the 3D Eversion switch on the right above of the transmitter then push the right rudder in any direction and then you can make 360 degree 3D tumbling operation in any direction and make successive tumbling stunt performance as well 2 Using 6 axis gyroscope quad copter bring you more fun Throw out the quad copter or push up throttle lever when it rolling the quad copter could hover smoothly in the sky BATTERY CHARGING Battery charging Take out the USB charging wire connect one end to the quad copter then insert the USB port of the USB charging wire to the USB port of the computer or the USB port of the power adapter to charge the battery During the time of cha
3. turn the two levers to the lower right corner as left image for seconds when indicator keep light up it finishes auto level calibration ILLUSTRATION ON CONTROLLING THE QUAD COPTER MODE 1 DEFAULTED MODE WHEN STARTING Operating direction Push the throttle up or down the quadcopter flies upward or downward Push the direction lever up or down the quadcopter flies forward or backward Pull the direction lever left or right the quadcopter flies to left side or right side Pull the throttle left or right the quadcopter turns to left or right Fine tuning operation When the quad copter keeps flying forward backward you can correct it by pressing under top fine tuning button When the quad copter keeps flying to left right side you can correct it by pressing the right left fine tuning button When the quad copter keeps rotating to left right you can correct it by pressing the left right fine tuning button ILLUSTRATION ON HOW TO CONTROL THE QUAD COPTER MODE 2 Operating direction Push the throttle up or down the quadcopter flies upward or downward Push the direction lever up or down the quadcopter flies forward or backward Pull the direction lever left or right the quadcopter flies to left side or right side Pull the throttle left or right the quadcopter turns to left or right Fine tuning operation When the quad copter keeps flying forward backward you can correct
4. when Matching freguency deus kindly check Pade3 overing or ti ter i etails please kindly check Page flying to one jest uicina Adjusting of Flying Resetting side not reset 3 Level calibration X11A PARTS OPTIONAL Below are the parts available for your kindly selection In order to facilitate our customers for placing an order we specially offer all kinds of parts for your kindly selection You can buy these parts via our local agent as well 11 01 X11 01B X11 01C X11 02 Fuselage red Fuselage white Fuselage black Protecting frames X11A 03 X11 06 Blades Motor A X11 07 X11 08 X11 09 Motor B Battery Circuit board X11 11 Transmitter X11C PARTS OPTIONAL Below are the parts available for your kindly selection In order to facilitate our customers for placing an order we specially offer all kinds of parts for your kindly selection You can buy these parts via our local agent as well X11C 01A X11C 01B X11C 01C X110 02 Fuselage red Fuselage white Fuselage black Protecting frames X11C0 03 Blades X11C 07 Motor B X11C 11 Camera PCB box BREAKDOWN amp DIAGRAM X110 04 Motor holder X11C 08 Battery X11C 12 Reader X116 05 Gear X116 09 Circuit board X110 13 Transmitter X11C0 06 Motor A X116 10 USB Code Description Code Metal shatter 02 Reversing blade 2 08 1 Protecting Rotating motor 2 fT L o
5. AGES 14 Mit XII CHE E 2 46 REMOTE CONTROL QUADCOPTER f S60 EMERSON b INSTRUCTION MANUAL IMPLEMENT STANDARD GB T26701 2011 Main characteristics e Four axis structure is applied which makes the quadcopter more flexible and rapid when flying It has the characteristics of wind resistant and can be flied indoor or outdoor e Built in 6 axis gyroscope for precise hovering in the sky e Modular design structure is applied more simple for assembly and convenient for maintenance e With 360 3D eversion function and throwing flight function The materials and specification mentioned in this instruction manual or the parts inside this package is for reference only Our company won t be responsible for any adaption of the outer package Nor shall we keep our customers informed in advance Any information updates or changes please be subject to our website PREFACE Dear customers Hello Thank you for purchasing our flying model Please read this instruction manual carefully in order to master the skill required quickly and operate this product more safely In the mean time please well keep the original of this instruction manual for future reference IMPORTANT INSTRUCTION 1 This product is not a toy but one precisive equipment that integrating mechanics and electronics with expertise of aerodynamics and high frequency transmitting It requires to be correctly assembled and debugged so as to preve
6. Use this product correctly and avoid operating by your own 4 Keep it far away from the high speed rotating part and heat source 5 Please conform to the sequence of power ON OFF As the picture below shown incorrect sequence of power ON OFF may cause this product out of control and affect your own safety or others Please form a good habit of switching on or switching off this product correctly ABOUT CONTENTS Product included following contents e Quadcopter e 2 4G Remote controller __ i e USB charging wire __ e Instruction manual Reader e Blade 4 pieces GET TO KNOW YOUR TRANSMITTER Introduction of transmitter Remote control Installing the battery High Low ON OFF speed switch power and indicator M 3D Eversion Left Right control control lever lever Trimming Forward and amp resetting backward trimmer Battery Cover IIl E TT Mode switch Left Fine tuning Right Fine tuning Open the back cover at the back of the transmitter Load 4PCS AA alkaline batteries correctly into the battery compartment as per the correct polarity shown on the battery compartment Step 2 Insert the power line into the quad copter and place it on the level ground Step 1 First of all press the ON OFF power switch Step 3 Push the throttle lever to the highest position and then pull it back to the lowest position this time there will be one clear sound sendi
7. d pull left lever up and down to connect signal between quodcopter and transmitter 2 Take Photo Make sure camera normally work when push the button C up camera will take a photo after a beep from transmitter and the GREEN indicator on camera will be RED and flash on time Take Video Make sure camera normally work when pull the button C down camera starts to take video after a beep from transmitter and the GREEN indicator on camera will change to RED than keep flashing Press the button C slightly again another beep from transmitter means video stopped and the RED flashing light on camera will be GREEN and keep light on TROUBLE SHOOTING 1 Re Matching First of all switch on the power of the transmitter then switch on No response 1 Matching freguency is not successfully the power of the aircraft and place it on from the made ue e T BH rottle lever to the highest and then aircraft 2 Insufficient power with the aircraft or pull it back to the st arin g position transmitter 2 Replace the battery of the transmitter or charge the aircraft The reaction 1 Replace the batteries inside the of aircraft is w not smart or 1 Insufficient power with the transmitter iranemitier rue 2 Antenna of the aircraft is snapped off 2 Re welding the antenna 1 The aircraft is not placed on the level 1 Re Matching freguency The aircraft 2 Reset the trimmer key on the transmitter ES not ground
8. ed if you do not remove it from the charger for a long time the battery may discharge automatically which may cause battery exhaustion When the battery voltage that the charger has tested is lower than the rated voltage the charger will re charge the battery until it is fully charged Charging or discharging too often or repeated charging or discharging may reduce the using life of the batteries BATTERY REPAIR amp MAINTENANCE 1 Battery should be put in the dried or ventilated place with environment temperature about 18 25 C 2 In order to enhance the using life of the battery please avoid repeat charging or excessive discharging 3 When the battery needs to be stored for a long time please charge the battery first That is to say charge the battery for about 50 60 of the volume and then well store it 4 f you do not use it for more than 1 months it s highly recommended that you need to check the battery voltage every month so as to make sure the voltage no less than 3V Otherwise please do by following No 3 mentioned PHOTOGRAPHY VIDEO INSTRUCTIONS 1 Methods Turn the quadcopter power on the camera works normally when the RED indicator change form flashing to green and keep light on If the RED indicator just light on and light off seconds later it means the SD card is not in the camera Please insert the SD card than the indicator light on GREEN 2 Get to know take photo and video Turn on the transmitter an
9. ng out from the transmitter this shows that the quad copter has entered into the pre fly state TIPS When matching signal keep the Si quad copter on horizontal position to fast matching and start a stable CAUTIONS 1 When the indicator of the transmitter appears eternal bright however the indicator of the quadcopter appears slow flashing this means that decoding is not successful This time please disconnect the power both of the quad copter and transmitter then repeat the pre flying steps 2 1 the quadcopter is tilting to one side abruptly or spinning while hovering please switch off the power both of the quad copter and transmitter and then repeat the pre flying steps 3 When the indicator of the quad copter keeps flashing slowly it means that the quad copter has entered into the low voltage protection state This time you need to charge the quadcopter FUNCTIONS MODE SWITCH FINE TUNING RESET AND LEVEL CALIBRATION Mode switch function Resetting function Keep pressing the button A then switch on the power Keep pressing the button B then switch on the power of the of the transmitter you can select Mode 1 or Mode 2 transmitter Enter into the Trimming amp Resetting Mode It is highly suggested that the freshman should reset the trimmer first before starting the first flight Level calibration function If quad copter always fly to a side when starting please re match signal and place it on a horizontal plane Than
10. nt the accident from being happened The product owner should operate or control it in safe way Please noted that we won t take any responsibility for any wrong operation as this may result in severe injury or loss of property and we can not control the operating process during the time when the user assemble or use this product 2 This product is suitable to be used by people who has operating experience in flying model or age no less than 14 years old 3 The flying ground we required should be the local field and legal for remote control flying 4 Once this product is sold we won t be responsible for any safety responsibility during the time the user operates or uses or controls this product 5 If there is any problem occurred during the time of using operating or repairing please reach our sales agent for details The sales agent that we authorized will provide you with the technical support and after sale service SAFTY amp CAUTIONS This R C flying model is a high dangerous commodity Please make sure that it should be flied far away from the crowd Please also pay more attention to the phenomenon such as incorrect assembly or damaged model or incorrect connection of electronic control equipment Please also pay attention to the flying safety when operating and know more about the accident that may be happened due to your own negligence 1 Keep it far away from the barrier or crowd 2 Keep it far away from the moisten environment 3
11. rging the red indicator of the USB will be ON When it is fully charged the red indicator will be OFF Caution 1 When using the computer for charging please remember to pull out the charging line before shutting down the computer 2 Please pay attention to aim correctly to the correct polarity when connecting the USB wire with the battery Please make sure the polarityshould not be upside down Charging time about 70 minutes Flying time about 5 minutes CAUTIONS WHEN CHARGING 1 When charging please put this product on the dried or ventilated area and keep it far away from heat source or explosive product 2 When charging please remove the batteries from the quad copter All the charging process should be under the guidance of the adult so as not to cause accident 3 When finish flying please do not charge the battery which surface temperature is still not cooled down Otherwise it may cause swollen battery or even cause fire disaster 4 During the process of battery charging falling down or striking by the outer force should be avoided Otherwise it may cause short circuited within the battery and thus may cause danger 5 In order to make sure safety please make sure that you need to use the original USB charging wire that made from our factory When the battery is used for a long time or appears aging or swollen please replace them timely 6 When the batteries are fully charg
Download Pdf Manuals
Related Search