RF-A 单门门禁控制器 - Sinolisecurity.com
Contents
1. 1 Modify management password press 0 gt input new management password gt press gt input new management password again gt press Note password is 4 8 digital number 2 Add user card press 1 gt read card gt input 3 digital code for the card gt continually read card gt press Note A card code is within 001 800 and 3 non repeatable digit numbers B Thelst card must be put with code or the card is ie invalid C if need add more than 1 card needn t input code for each card from the 2 card on and just read card one by one finally press button 3 Delete user card A Delete all users card press2 gt press0000 gt press B Delete read card press2 gt read card gt press C Delete lost card press2 gt the card code gt press 4 Set up open mode A Open with reading valid card press 300 gt press B Open with reading valid card and password press 301 gt press C press302 gt press open with reading valid card or password Note Factory setup is 302 5 Set up open time press4 gt X X gt press Note XX is during 00 99 measure unit is second and original is 03 seconds and 0 is added for less than 2 digit 6 Modify user password press 5 gt input 1 group new password with 4 digital number gt press gt input the new password again gt press to save 7 Setup for theftproof alert press 600 gt press to close the output of alert to prevent from disassembling press 602. 1 gt press to trigger the output of alert to prevent from disassembling Note origins setup is 600 with close before delivery 8 Save setup and exit from programming press button to save Note above any setup after completing must be saved within 1 minute by pressing gt Usage 1 open by card Under normal working environment door can be opened with 1 valid card 2 open by card and password Door can be opened if correct password is input within 10 seconds after card is reading 3 open by password Door can be opened by inputting correct user password Attention the door controller supports 3 modes opening by card by password amp card and by password Instruction for Stand alone Single Door Access Controller SL 098 gt Description for setup of jumper wire 1 J1 jumper wire 2 and 3 pin connect PUSH output NO signal 1 and 2 pin connect PUSH output NC signal default 2 J2 jumper wire 2 and 3 pin connect output high electrical level signal default 1 and 2 pin connect output low electric level signal Note On normal condition please don t change the jumper wire setup gt Initialization way for door controller Step 1 switch off power and keep pressing RESET unloosen Step 2 switch on the power and keep pressing RESET for 5s then loosen and initialization is completed Status the door controller goes into working status with 1 sound of buzzer Note 1 In
3. Instruction for Stand alone Single Door Access Controller SL 098 gt Technical Parameters Working voltage DC 12V Unlock current lt 1000mA Static current lt 60mA Capacity of cards 800 pieces Maximum card read distance 5 10cm RF card type EM or EM compatible card Working temperature 40 C 70 C Working moisture 10 90 Size 117x117x21mm Attention 1 Please strictly operate it per user manual 2 Please don t install it with power on Specially pay more attention to positive and negative of power gt How to assemble Unpack cross screw that fixes faceplate and motherboard then take off motherboard and get it assembled on side wall which is at the exit with attention on vertical orientation Warning 1 please ensure to switch off power before connecting lines and switch on power after all lines being connected well Please be sure that power voltage is 12v and that positive and negative are in right place 2 the switch to theftproof is at the left bottom corner Buzzer will keep short ring alert when back cover is open or spring is loose and alert will stop once back cover is closed this function is closed before delivery User can open it according to his specific requirement gt Methods of Programming Original management pass word is 12345 and user pass word is 8888 1 Enter programming Press gt input management pass word gt press 2 Function setup under programming circumstance
4. itialization only change system password into default programming password 12345 and user password 8888 others data will not be changed 2 Under general condition initialization will not be used unless forget the password SB 098 Access Controller gt Wiring Instruction 1 1 pin connect the positive of power 2 pin connect negative of power please pay attention it cannot be wrong connected 2 3 4 pin PUSH is signal line connect with PUSH of power supply 4 pin output 12V signal 3 5 pin and 6 pin connect exit button 4 7 pin and 8 pin connect doorbell Note To keep door controller work steadily please don t connect electric lock directly with controller We suggest you directly connect electric lock and exit button with power supply See the below diagram Exit Button Fail Safe Lock Aiddng mod
Download Pdf Manuals
Related Search