User`s Manual
Contents
1. Part 99185 Rev C ECO B469 TABLE OF CONTENTS CHAPTER 1 INTRODUCTION About This Manual Typographical Conventions Your Next Step CHAPTER 2 PREREQUISITES CHAPTER 3 GETTING STARTED Unpacking Your Cabinet Storage Cabinet Components Setting Up Your Cabinet Component Identification Standard Base Storage Cabinets Acid Storage Cabinets Solvent Storage Cabinets Vacuum Pump Storage Cabinets Installation Cabinet Leveling All Cabinets Vent Installation Acid Storage Cabinet Solvent Storage Cabinet Filler Panel All Cabinets SpillStopper Work Surface Electrical Ground Connection Solvent Storage Cabinet Acid Storage Cabinet Shelf Liner Adjustable Shelf Solvent Storage Cabinet Junction Box Connection Vacuum Pump Cabinet Environmental Conditions CHAPTER 4 USING YOUR CABINETS Normal Operation CHAPTER 5 MAINTAINING YOUR CABINETS BR RU 10 10 12 13 13 15 17 19 21 21 22 22 23 24 25 27 28 28 28 29 31 31 33 APPENDIX A CABINET DIMENSIONS APPENDIX B CABINET REPLACEMENT PARTS APPENDIX C CABINET ACCESSORIES APPENDIX D QUICK REFERENCE STORAGE CABINETS DECLARATION OF CONFORMITY 35 41 43 47 48 CHAPTER 1 INTRODUCTION Congratulations on your purchase of a Protector Storage Cabinet Labconco manufacturers four types of Storage Cabinets Acid Solvent Standard Base and Vacuum Pump Protector Acid Storage Cabinets have been engineered2. STORAGE CABINET After the Storage Cabinet has been installed as detailed in Chapter 3 Getting Started you are ready to begin using it Read this chapter to learn how to e Properly store and vent chemicals e Operate it in a safe manner Normal Operation Although the Storage Cabinet is engineered to maintain the optimum in operator safety caution should always be used while working with it Good general housekeeping procedures with the following specific recommendations should allow you to operate your cabinet safely for years to come e Properly vent your storage cabinet to the outside atmosphere e It is not recommended to store solvents and acids in the same storage cabinet For best results use two separate storage cabinets to safeguard or protect these materials 31 Chapter 4 Using Your Storage Cabinet Do not block open the door assembly on the solvent storage cabinet This is an unsafe practice should a fire occur Do not store flammable material in excess of the individual Solvent Storage Cabinet rating Ratings are located on the nameplate of each Solvent Storage Cabinet Do not block either vent connection as it will alter the airflow pattern in the cabinet and could interfere with ventilation of the cabinet Always clean up spills immediately to prolong the life of your Storage Cabinet CHAPTER 5 MAINTAINING YOUR STORAGE CABINETS Under normal conditions the Storage Cabinet
3. barrel plugs 1 used with your vent connections should it become necessary to isolate the cabinet from the vent connection as ducted 23 Chapter 3 Getting Started Filler Panel All Cabinets One 8 0 filler panel and filler panel angle has been supplied with your cabinet to close off the plumbing access Attach the filler panel angle directly to the back wall of the cabinet structure using the four 8 sheet metal screws that hold the back panel in position Next attach the filler panel to this angle by the three 8 sheet metal screws provided SIE ER Different filler panel depths are available refer to Appendix C Storage Cabinet Accessories for filler panel selection Filler Panel Filler Panel Angle Back of Cabinet 24 SpillStopper Work Surface Once your cabinet has been properly leveled vented optional and filler panel installed place the epoxy work surface directly on top of the cabinet It is not necessary to attach the work surface to the cabinet It is held in place both by its own weight and the weight of the fume hood and other equipment on top of it Align the work surface on top of the cabinet before making plumbing or electrical connections through the work surface itself Normally the work surface is aligned flush with the top front of the cabinet and overhangs the back of the cabinet WARNING Never use screws and or bolts to fasten the epoxy molded work surface
4. directly to the cabinet as this can damage the work surface Chapter 3 Getting Started 25 Chapter 3 Getting Started SpillStopper Work Surface Installation Detail 419 5900 4800 INSIDE ES 125 320 HOLD THIS DIMENSION FOR PROPER AIRFLOW 3575 i SECTIONAL SIDE VIEW Dimensions Shown in Inches Hood Internal Filler Panel Hood Depth Depth Depth Work Surface lt B gt p p gt Depth 33 19 24 8 30 39 19 30 14 36 45 19 36 20 42 26 Electrical Ground Connection Solvent Storage Cabinet Use the grounding screw located in the lower right hand corner on the back panel of your solvent storage cabinet to properly ground the cabinet structure Remove the grounding screw and attach a grounding wire directly to the back of the cabinet at this point Make sure you have a tight bond when you retighten the grounding screw Electrical Ground Connection Chapter 3 Getting Started 27 Chapter 3 Getting Started Shelf Liner Acid Storage Cabinet Polyethylene liner trays have been included in your Acid Storage Cabinet for added chemical resistance Place a shelf liner in the cabinet floor The watertight tray collects spills and drips from bottles and containers stored within the cabinet Adjustable Shelf Solvent Storage Cabinet Remove the four shelf brackets included with the cabi
5. requirements Then go to Chapter 3 Getting Started for instructions on how to install the Storage Cabinet and make all of the necessary connections For information on the operational characteristics of the Storage Cabinet go to Chapter 4 Using Your Storage Cabinet Chapter 1 Introduction If the Storage Cabinet is installed and you need to perform routine maintenance on the Storage Cabinet proceed to Chapter 5 Maintaining Your Storage Cabinet For information on the dimensions of the Storage Cabinet proceed to Appendix A For replacement parts on the Storage Cabinet proceed to Appendix B To find information for Accessories for the Storage Cabinet proceed to Appendix C For a quick reference of all Cabinets refer to Appendix D Chapter 1 Introduction CHAPTER 2 PREREQUISITES Before you install your Storage Cabinet you need to prepare your site for installation Carefully examine the location where you intend to install the Storage Cabinet You must be certain that the area is level and of solid construction In addition your Storage Cabinet should be adjacent to a vent connection to allow for venting to the exterior of the building 1f so desired Otherwise it is typical to vent the Storage Cabinet through the work surface and fume hood which is supported by the Storage Cabinet Space Requirements Refer to Appendix A Storage Cabinet Dimensions for complete Storage Cabinet dimensio
6. to efficiently store and ventilate corrosive materials and include an interior plastic liner to protect the metal from corrosion Protector Solvent Storage Cabinets are designed to efficiently store flammable materials and includes a 1 1 2 double wall construction for fire protection Protector Standard Base Storage Cabinets are utilized for general storage and are not recommended for corrosive or flammable materials Protector Vacuum Pump Storage Cabinets are utilized for vacuum pump storage All cabinets feature 18 gauge steel construction with epoxy coated paint to give you both a durable and chemically resistant finish that ensures many years of quality service The Labconco Protector Storage Cabinets has been engineered in accordance with NFPA 30 OSHA 1910 62 and all pertinent SEFA regulations The cabinets Chapter 1 Introduction are available in several configurations to meet your various requirements All Protector Storage Cabinets are designed with provisions for venting to the exterior of your laboratory Vent connections are located on the back wall of the cabinet and can be used at the discretion of the customer The vent connection on the Solvent Storage Cabinet is supplied with a closure plug on both sides and is diametrically opposed on the back wall of the cabinet for optimum airflow throughout its interior The vent connection on the Acid Cabinet and Standard Base Cabinet is l
7. 0 ADA Acid Storage Cabinet 9902000 thru 9902400 Solvent Storage Cabinet 9903000 thru 9903400 Self Closing Solvent Storage Cabinet 9906000 thru 9906100 ADA Solvent Storage Cabinet 9906200 thru 9906300 ADA Self Closing Solvent Storage Cabinet 9907000 thru 9907100 Vacuum Pump Cabinet Serial No Various See Individual Declaration Year of Manufacture 1999 and Subsequent I the undersigned hereby declare that the equipment specified above conforms to the above Directive s and Standard s See individual Declaration of Conformity which will be signed by the importer for your country Signature Full Name Position An individual version of this declaration is included with your shipping customs documentation Labconco P N 36960 19 REV A ECO B296 48 For more information please contact us E mail sales expotechusa com Website www ExpotechUSA com
8. 19104 12 9919105 43 Appendix C Storage Cabinet Accessories Work Surfaces 9727500 4 Work Surface Only 30 Depth 9727501 S Work Surface Only 30 Depth 9727502 6 Work Surface Only 30 Depth 9727503 8 Work Surface Only 30 Depth B 9727504 10 Work Surface Only 30 Depth Two Piece 9727505 12 Work Surface Only 30 Depth Two Piece 9727506 16 Work Surface Only 30 Depth Three Piece 9727507 4 Work Surface Only 36 Depth 9727508 5 Work Surface Only 36 Depth 9727509 6 Work Surface Only 36 Depth 9727510 8 Work Surface Only 36 Depth 9727311 10 Work Surface Only 36 Depth Two Piece 9727512 12 Work Surface Only 36 Depth Two Piece 9727513 16 Work Surface Only 36 Depth Three Piece 9727514 4 Work Surface Only 42 Depth 9727515 5 Work Surface Only 42 Depth 9727516 6 Work Surface Only 42 Depth 9727517 8 Work Surface Only 42 Depth 9727518 10 Work Surface Only 42 Depth Two Piece 9727519 12 Work Surface Only 42 Depth Three Piece 9727520 16 Work Surface Only 42 Depth Three Piece 9732000 4 HOPEC Work Surface 9732001 5 HOPEC Work Surface 9732002 6 HOPEC Work Surface 9732003 8 HOPEC Work Surface 9732004 4 HOPEC Work Surface with 1 cupsink cutout 9732005 5 HOPEC Work Surface with 1 cupsink cutout 9732006 6 HOPEC Work Surface with 1 cupsink cutout 9732007 8 HOPEC Work Surface with 1 cupsink cutout Other Work Surfaces with cutout options are a
9. 300 24 ADA Standard Base Cabinet Left Hinged 9904400 18 ADA Standard Base Cabinet Left Hinged 9904500 12 ADA Standard Base Cabinet Left Hinged 9901000 48 Acid Cabinet 9901100 36 Acid Cabinet 9901200 30 Acid Cabinet 9901300 24 Acid Cabinet Right Hinged 9901400 18 Acid Cabinet Right Hinged 9901500 24 Acid Cabinet Left Hinged 9901600 18 Acid Cabinet Left Hinged 9905000 24 ADA Acid Cabinet Right Hinged 9905100 18 ADA Acid Cabinet Right Hinged 9905200 24 ADA Acid Cabinet Left Hinged 9905300 18 ADA Acid Cabinet Left Hinged 9902000 48 Solvent Cabinet 9902100 36 Solvent Cabinet 9902200 30 Solvent Cabinet 9902300 24 Solvent Cabinet Right Hinged 9902400 24 Solvent Cabinet Left Hinged 9903000 48 Self Closing Solvent Cabinet 9903100 36 Self Closing Solvent Cabinet 9903200 30 Self Closing Solvent Cabinet 9903300 24 Self Closing Solvent Cabinet Right Hinged 9903400 24 Self Closing Solvent Cabinet Left Hinged 9906000 24 ADA Solvent Cabinet Right Hinged 9906100 24 ADA Solvent Cabinet Left Hinged 9906200 24 ADA Self Closing Solvent Cabinet Right Hinged 9906300 24 ADA Self Closing Solvent Cabinet Left Hinged 9907000 18 Vacuum Pump Cabinet Right Hinged 9907100 18 Vacuum Pump Cabinet Left Hinged 11 Chapter 3 Getting Started 12 Plus the Following Part Component Description 9920301 Panel Filler Standard f
10. ET WITHOUT THE PRIOR AUTHORIZATION OF LABCONCO UNAUTHORIZED RETURNS WILL NOT BE ACCEPTED S IF YOUR STORAGE CABINET WAS DAMAGED IN TRANSIT YOU MUST FILE A CLAIM DIRECTLY WITH THE FREIGHT CARRIER LABCONCO CORPORATION AND ITS DEALERS ARE NOT RESPONSIBLE FOR SHIPPING DAMAGE Do not discard the carton or packing material for your Storage Cabinet until you have checked all of the components installed and tested the Storage Cabinet Storage Cabinet Components As previously mentioned Labconco manufactures four types of Storage Cabinets Acid Solvent Standard Base and Vacuum Pump The different Storage Cabinet models require different assembly components Locate the model of Storage Cabinet you received in the following tables Verify that the components listed are present and undamaged Chapter 3 Getting Started Model Number Description 9900000 48 Standard Base Cabinet 9900100 36 Standard Base Cabinet 9900200 30 Standard Base Cabinet 9900300 24 Standard Base Cabinet Right Hinged 9900400 18 Standard Base Cabinet Right Hinged 9900500 12 Standard Base Cabinet Right Hinged 9900600 24 Standard Base Cabinet Left Hinged 9900700 18 Standard Base Cabinet Left Hinged 9900800 12 Standard Base Cabinet Left Hinged 9904000 24 ADA Standard Base Cabinet Right Hinged 9904100 18 ADA Standard Base Cabinet Right Hinged 9904200 12 ADA Standard Base Cabinet Right Hinged 9904
11. User s Manua Protector Storage Cabinets Standard Acid Solvent and Vacuum Pump Models 9900000 9901000 9902000 9903000 9904000 9900100 9901100 9902100 9903100 9904100 9900200 9901200 9902200 9903200 9904200 9900300 9901300 9902300 9903300 9904300 9900400 9901400 9902400 9903400 9904400 9900500 9901500 9904500 9900600 9901600 9900700 9900800 9905000 9906000 9907000 9905100 9906100 9907100 9905200 9906200 9905300 9906300 Labconco s Mascot Labby the LABster Protecting your laboratory environment R aZ LABCONCO For more information please contact us E mail sales expotechusa com Website www ExpotechUSA com The information contained in this manual and the accompanying product are copyrighted and all rights are reserved by Labconco Corporation Labconco Corporation reserves the right to make periodic design changes without obligation to notify any person or entity of such change Protector is a registered trademark of Labconco Corporation Warranty Labconco provides a warranty on all parts and factory workmanship The warranty includes areas of defective material and workmanship provided such defect results from normal and proper use of the equipment The warranty for all Labconco products will expire one year from date of installation or two years from date of shipment from Labconco whichever is sooner except the following e Purifier Delta Series Biological Safety Cabinets carry a thre
12. andard Base and Vacuum Pump Cabinets Chapter 1 Introduction EE sl 5 Typographical Conventions Recognizing the following typographical conventions will help you understand and use this manual e Book chapter and section titles are shown in italic type e g Chapter 3 Getting Started e Steps required to perform a task are presented in a numbered format e Comments located in the margins provide suggestions reminders and references e Critical information is presented in boldface type in paragraphs that are preceded by the exclamation icon Failure to comply with the information following an exclamation icon may result in injury to the user or permanent damage to the Storage Cabinet e Important information is presented in capitalized type in paragraphs that are preceded by the pointer icon It is imperative that the information contained in these paragraphs be thoroughly read and understood by the user e Information that is specific to a particular model of Storage Cabinet The A icon indicates text specific to the Acid Storage Cabinet the S icon indicates text specific to the Solvent Storage Cabinet the B icon indicates text specific to the Standard Base Storage Cabinet and the V icon indicates text specific to the Vacuum Pump Storage Cabinet Your Next Step If your Storage Cabinet needs to be installed proceed to Chapter 2 Prerequisites to ensure your installation site meets all of the
13. andle Solvent Rotary Catch Door Latch Shelf Support Clip Solvent 48 Adjusting Solvent Shelf 36 Adjusting Solvent Shelf 30 Adjusting Solvent Shelf 24 Adjusting Solvent Shelf Bushing Nylon Door Hinge Support Lower Hinge Assembly Right Lower Hinge Assembly Left Upper Hinge Pin 48 Lower Acid Polyethylene Tray 36 Lower Acid Polyethylene Tray 30 Lower Acid Polyethylene Tray 24 Lower Acid Polyethylene Tray 18 Lower Acid Polyethylene Tray Cabinet Type All All All but Solvent Solvent Only All but Solvent Solvent Only Solvent Only Solvent Only Solvent Only Solvent Only All All All All Acid Only Acid Only Acid Only Acid Only Acid Only 41 Appendix B Storage Cabinet Replacement Parts 42 APPENDIX C STORAGE ABINET ACCESSORIES The following accessories are available for the Storage Cabinets Vent Kit Part No 3591100 Vent Kit includes one PVC adapter one PVC 90 A V elbow locknut and one section of 2 diameter PVC pipe for venting the cabinet through a Protector SpillStopper Work Surface and into a fume hood Shelf Kits for Acid Storage Cabinets These kits provide additional shelf polyethylene A tray and mounting hardware 48 9919000 36 9919001 30 9919002 24 9919003 18 9919004 Shelf Kits for Standard Base Cabinets These kits provide additional shelf and mounting hardware 48 9919100 36 9919101 30 9919102 24 9919103 18 99
14. dard Base Storage Cabinet properly first decide which of the two vent connections in the back of the cabinet that you intend to use The lower vent connection should be B used for heavier than air vapors and the upper vent connection should be used for lighter than air vapors to obtain the best results within the cabinet structure Vent Kit P N 35911 allows the Acid Storage Cabinet or Standard Base Cabinet to be vented directly into a Protector Laboratory Hood Run the vent line through either the work surface and fume hood or connect through separate duct system to the outside The vent is sized for 2 diameter nominal PVC pipe FRE PRE OUT TO DESAT LEKGTH rar 22 Chapter 3 Getting Started Vent Installation Solvent Storage Cabinet To ventilate the cabinet properly remove both the exterior and interior barrel plugs from the vent connection that you are venting The lower vent connection should be used for heavier than air vapors and the higher vent connection on the back wall should be used for lighter than air vapors to obtain the best fume removal within the cabinet The cabinet vent connections are designed to accept 2 diameter threaded metal pipe material which can be purchased locally Once the connection on the back of the cabinet has been completed remove both the internal and external plugs from the remaining vent connection to allow for proper airflow from the cabinet CAUTION Retain the
15. e year warranty from date of installation or four years from date of shipment from Labconco whichever is sooner Carts carry a lifetime warranty Glassware is not warranted from breakage when dropped or mishandled This limited warranty covers parts and labor but not transportation and insurance charges In the event of a warranty claim contact Labconco Corporation or the dealer who sold you the product If the cause is determined to be a manufacturing fault the dealer or Labconco Corporation will repair or replace all defective parts to restore the unit to operation Under no circumstances shall Labconco Corporation be liable for indirect consequential or special damages of any kind This statement may be altered by a specific published amendment No individual has authorization to alter the provisions of this warranty policy or its amendments Lamps and filters are not covered by this warranty Damage due to corrosion or accidental breakage is also not covered Limitation of Liability The disposal and or emission of substances used in connection with this equipment may be governed by various federal state or local regulations All users of this equipment are required to become familiar with any regulations that apply in the user s area concerning the dumping of waste materials in or upon water land or air and to comply with such regulations Labconco Corporation is held harmless with respect to user s compliance with such regulations
16. ent Kit the cabinet may be vented to the fume hood or directly outside Instructions for venting can be found on page 22 For Acid Vent Kit accessory see page 43 Optional Accessory Shelf Features 16 gauge steel shelf with polyethylene molded tray to hold spills and provides a chemical resistant surface The shelf support kit allows height adjustment Leveling Feet Four individual leveling feet provide adjustability to level the cabinet per the requirements of your laboratory floor Acid Shelf Liners Vacuum formed polyethylene liner trays fit down into both the adjustable shelf and the bottom floor of the cabinet These liner trays give additional chemical resistance to the cabinet interior and are removable for easy cleaning The liners are watertight in construction and will contain any minor spills and or drips from containers stored in the cabinet Interior Liner Interior sides and back are fully lined with polyethylene plastic to provide excellent corrosion resistance Chapter 3 Getting Started 15 Chapter 3 Getting Started Protector Acid Storage Cabinet 4 NOT SHOWN LEVELING FOOT Protector Solvent Storage Cabinets Models 9902000 9902100 9902200 9902300 9902400 9903000 9903100 9903200 9903300 9903400 9906000 9906100 9906200 9906300 1 Double Wall Construction Cabinet features 18 gauge epoxy coated steel exterior and interior liner walls with a 1 1 2 air s
17. f Closing Doors 9903300 9903400 24 ADA 9906000 9906100 9905000 9905200 24 ADA w Self Closing 9906200 9906300 Doors 18 ADA 9905100 9905300 12 ADA STANDARD BASE VACUUM PUMP Size Description Dual Doors Right Hinge Left Hinge Dual Doors Right Hinge Left Hinge 48 9900000 36 9900100 30 9900200 24 9900300 9900600 18 9900400 9900700 9907000 9907100 12 9900500 9900800 48 w Self Closing Doors 36 w Self Closing Doors 30 w Self Closing Doors 24 w Self Closing Doors 24 ADA 9904000 9904300 24 ADA w Self Closing Doors 18 ADA 9904100 9904400 12 ADA 9904200 9904500 47 Declaration of Conformity DECLARATION OF CONFORMITY Application Council Directive s 73 23 EEC 89 336 EEC Standard s to which conformity is declared EN61010 EN55022 EN50082 1 Manufacturer s Name Labconco Corporation Manufacturer s Address 8811 Prospect Avenue Kansas City MO 64132 USA Importer s Name See Shipping Customs Documents Importer s Address See Shipping Customs Documents for your equipment Type of Equipment Laboratory Equipment Storage Cabinets Model No 9900000 thru 9900800 Standard Base Cabinet 9904000 thru 9904500 ADA Standard Base Cabinet 9901000 thru 9901600 Acid Storage Cabinet 9905000 thru 990530
18. nal specifications Your Next Step After you have determined that the location for your Storage Cabinet accommodates the installation you are ready to unpack and install your Storage Cabinet Proceed to Chapter 3 Getting Started Chapter 2 Prerequisites CHAPTER 3 GETTING STARTED Now that the site for your Storage Cabinet is properly prepared you are ready to unpack inspect and install the Storage Cabinet Read this chapter to learn how to Unpack and move the Storage Cabinet Set up the Storage Cabinet Acid Solvent Standard Base and Vacuum Pump Properly level the Storage Cabinet Properly install the accessory work surface Attach the filler panel for additional aesthetics Properly vent the Storage Cabinet Properly ground the Solvent Cabinet Connect the electrical supply source to the Vacuum Pump Cabinet Depending upon which model of Storage Cabinet you are installing you will need common hand tools including a Phillips head screwdriver a flat blade screwdriver a 34 open end wrench and pliers to complete the instructions in this chapter Chapter 3 Getting Started 10 Unpacking Your Storage Cabinets Carefully unpack the Storage Cabinet and inspect it for damage that may have occurred in transit If your Storage Cabinet is damaged notify the delivery carrier immediately and retain the entire shipment intact for inspection by the carrier DO NOT RETURN ANY STORAGE CABIN
19. net s leveling feet and place one bracket in each of the shelf positions located on the interior walls of the cabinet Make sure that the shelf brackets are located at the same height to assure that the shelf will be level when placed in its working position To install simply squeeze the shelf bracket with pliers and place in the shelf positions of your cabinet Junction Box Connection Vacuum Pump Storage Cabinet Connect power to the electrical junction box provided for the vacuum pump through the back panel to the receptacle Chapter 3 Getting Started Environmental Conditions This equipment is designed to be safe under the following conditions Indoor use Altitude up to 6562 Ft 2000m Temperature 41 to 104 F 5 to 40 C Maximum relative humidity 80 for temperatures up to 88 F 31 C decreasing linearly to 50 relative humidity at 104 F 40 C e Main supply voltage fluctuations not to exceed 10 of the nominal voltage e Transient overvoltages according to Installation Categories II Overvoltage Categories per IEC 1010 e Pollution degrees 2 in accordance with IEC 664 normally only non conductive foreign matter solid liquid or gaseous ionized gases that may produce a reduction of dielectric strength or surface resistivity occurs Occasionally however a temporary conductivity caused by condensation must be expected Chapter 3 Getting Started 30 CHAPTER 4 Usina Your
20. ocated on the back wall of the cabinet and does not include a closure plug LEVELING FOOT Chapter 1 Introduction About This Manual This manual will help you learn how to install use and maintain your Storage Cabinet Instructions for performing routine maintenance and for minor modifications to your Storage Cabinet are included Chapter 1 Introduction provides a brief overview of the Storage Cabinets explains the organization of the manual and defines the typographical conventions used in the manual Chapter 2 Prerequisites explains what you need to do to prepare your site before you install the Storage Cabinet Chapter 3 Getting Started contains the information you need to properly unpack inspect and install the Storage Cabinet Chapter 4 Using Your Storage Cabinet discusses the normal operation of the Storage Cabinet Chapter 5 Maintaining Your Storage Cabinet explains how to perform routine maintenance on the Storage Cabinet Appendix A Storage Cabinet Dimensions contains comprehensive diagrams showing the dimensions for the Storage Cabinets Appendix B Storage Cabinet Replacement Parts contains a list of service parts for the Storage Cabinets Appendix C Storage Cabinet Accessories lists the part numbers and descriptions of the accessories available for the Storage Cabinet Appendix D Storage Cabinet Quick Reference lists sizes and part numbers for Solvent Acid St
21. or 30 Interior Depth Protector XL Fume Hood or 9920304 Panel Filler ADA for 30 Interior Depth Protector XL Fume Hood 9920400 Angle Filler Panel for 30 Interior Depth Protector XL Fume Hood or 9920401 Angle Filler Panel ADA for 30 Interior Depth Protector XL Fume Hood 1928300 Leveling Feet 4 Different filler panel depths are available refer to Appendix C Storage Cabinet Accessories for filler panel selection If you do not receive one or more of the components listed for your Storage Cabinet or if any of the components are damaged contact Labconco Corporation immediately for further instructions Setting Up Your Storage Cabinet After you verify the Storage Cabinet components listed on the following pages move your Storage Cabinet to the location where you want to install it Then follow the steps for installation Chapter 3 Getting Started Component Identification Protector Standard Base Storage Cabinets Models 9900000 9900100 9900200 9900300 9900400 9900500 9900600 9900700 9900800 9904000 9904100 9904200 9904300 9904400 9904500 1 Cabinet Features 18 gauge steel exterior sidewalls The cabinet shell is epoxy coated to provide a durable chemical resistant surface 2 Door Assembly Cabinet features one or two manual closing non locking doors The doors are 18 gauge epoxy coated steel and feature a strike and latch assembly to hold them in position once clo
22. pace located between them Locking Door Assembly Cabinet features one or two manual closing doors The doors are held in the closed position by the three position locking handles NOTE Some models feature one or two self closing doors Shelf 16 gauge steel shelf features fully welded corners to hold spills and epoxy coated to provide a chemical resistant surface The shelf supports inside the cabinet allows for height adjustment Vent Connection Two vent connections are located on the back wall of the cabinet and are diametrically opposed Each vent connection includes a threaded coupling two flame arrestors and closure plugs Instructions for venting can be found on page 23 Leveling Feet Four individual leveling feet provide adjustability to level the cabinet per the requirements of your laboratory floor Optional Self Closing Doors Some models include a self closing door mechanism to close doors automatically in case of fire Chapter 3 Getting Started 17 Chapter 3 Getting Started Protector Solvent Storage Cabinet 4 VENT CONNECTION ON BACK 5 LEVELING FOOT Chapter 3 Getting Started Protector Vacuum Pump Storage Cabinets Models 9907000 9907100 1 Cabinet Features 18 gauge steel exterior sidewalls The cabinet shell has been epoxy coated to provide a durable chemical resistant surface 2 Door Assembly Cabinet features one man
23. requires little maintenance The following maintenance schedule is recommended As Needed Remove liquid containers from cabinet and clean up spills 33 Chapter 5 Maintaining Your Storage Cabinets 34 APPENDIX A STORAGE CABINET DIMENSIONS The following drawings provide dimensions for the Standard Base Cabinet Acid Storage Cabinet Solvent Storage Cabinet and the Vacuum Pump Cabinet 35 Appendix A Storage Cabinet Dimensions Protector Standard Base Cabinet 3575 DM TO ACHIEVE 37 00 WORKSURFACE 35 50 MIN 3675 MAX HEIGHT 31 50 MIN ADA ADA 31 75 DIM 32 75 MAX ADA TO ACHIEVE 33 00 WORKSURFACE HEIGHT 3 75 MIN FILLER PANEL HULER PANEL FRONT SIDE 1550 STD pf 950 OPT A 2206 21 50 OPT z B PLUMBING ACCESS 700 mm 664 1227 1027 ADA 19 25 1525 ADA 800 VENT CONNECTIONS STANDARD BASE MODEL DIM r DM S EEN a es EE El al 36 Appendix A Storage Cabinet Dimensions Protector Acid Storage Cabinet SE 35 75 DIM TO ACHIEVE 37 00 WORKSURFACE HEIGHT 35 50 MIN 36 75 MAX 31 50 MIN ADA ADA 31 75 DIM 3275 MAX ADA TO ACHIEVE 33 00 WORKSURFACE HEICHT 375 MIN FILLER PANEL FRONT SIDE 1550 STD mer 950 OPT A 22 06 2150 OPT gr 6 00 VENT CONNECTIONS PLUMBING ACCESS 544 Er 10 19 819 ADA 1950 1550 IADA 1200 12 00 BM B 37 Appendix A S
24. sed 3 Vent Connection Cabinet features two vent connections on the back wall of the cabinet The vent openings have been left open and venting is at the discretion of the customer Instructions for venting can be found on page 22 For Base Vent Kit accessory see page 43 4 Optional Accessory Shelf Features 16 gauge steel shelf to provide additional storage Shelf support kit allows height adjustment 5 Leveling Feet Four individual leveling feet provide adjustability to level the cabinet per the requirements of your laboratory floor 13 Chapter 3 Getting Started Protector Standard Base Storage Cabinet 4 NOT SHOWN ine LEVELING FOOT 14 Protector Acid Storage Cabinets Models 9901000 9901100 9901200 9901300 9901400 9901500 9901600 9905000 9905100 9905200 9905300 1 Cabinet Features 18 gauge steel exterior sidewalls The cabinet shell is epoxy coated to provide a durable chemical resistant surface Door Assembly Depending on the width the cabinet features one or two manual closing non locking doors The doors are 18 gauge epoxy coated steel and feature a strike and latch assembly to hold them in position once closed The backs of the doors are lined with polyethylene to provide additional corrosion protection Vent Connection Cabinet features two vent connections located on the back wall of the cabinet These vents are open Using a V
25. torage Cabinet Dimensions Protector Solvent Storage Cabinet SHELF INCLUDED SOLVENT CABINET ONLY Br ef 3575 DIM TO ACHIEVE 37 00 35 50 MIN VE 3675 MAX I 3150 MN ADA ADA 31 75 DIM 3275 MAX ADA TO ACHEVE 33 00 WORKSURFACE HEIGHT Eg TT eee 375 MN i z FILLER PANEL FRONT SIDE EE 950 OPT A 2206 2150 OPT p PLUMBING ACCESS en a 1227 f 1027 ADA 1925 15 25 ADA 800 VENT CONNECTIONS SOLVENT MODEL DM A DM B 48 36 3 24 24 ADA 8 e 158 30 4 4 38 Appendix A Storage Cabinet Dimensions Protector Vacuum Pump Cabinet 7 35 75 DIM TO ACHIEVE 37 00 35 50 MIN WORKSURFACE 36 75 MAX HEIGHT 31 50 MIN ADA ADAI 31 75 DIM 32 75 MAX IADA TO ACHIEVE 33 00 WORKSURFACE HEIGHT Fers 375 MN _ FRONT SIDE CEN A EL 950 OPT 18 00 22 06 21 50 OPT 12 27 10 27 ADA 1925 1525 ADA 8 00 PLUMBING ACCESS VENT CONNECTIONS 39 Appendix A Storage Cabinet Dimensions 40 APPENDIX B STORAGE CABINET REPLACEMENT PARTS The following pages list components that are typical replacement parts If other parts are required contact Product Service Part 1928300 1663600 1928400 3598300 1934500 1930600 9921200 9921201 9921202 9921203 1933400 9917100 9717101 9920700 9922100 9922101 9922102 9922103 9922104 Description Leveling Feet Door Bumpers Handle Acid Lock H
26. ual closing non locking door The door is of 18 gauge epoxy coated steel and features a strike and latch assembly to hold it in position once closed 3 Vent Connection Cabinet features two vent connections on the back wall of the cabinet These vent openings have been left open and venting is left to the discretion of the customer 4 Electrical Connection Cabinet features 115V 60 Hz electrical outlet to provide power for the vacuum pump 5 Leveling Feet Four individual leveling feet provide adjustability to level the cabinet per the requirements of your laboratory floor 19 Chapter 3 Getting Started 20 Protector Vacuum Pump Storage Cabinet LEVELING FOOT Installation Cabinet Leveling All Models Each cabinet is supplied with four independent leveling feet These leveling feet have been packaged separately and must be installed on the bottom of the cabinet before installation Each leveling foot is independently adjustable by turning it by means of a crescent wrench underneath the cabinet All of the leveling feet with exception to the Solvent Storage Cabinet can be adjusted with a flat blade screw driver from inside the cabinet through the access holes in the lower metal pan LEVELING FOOT Chapter 3 Getting Started 21 Chapter 3 Getting Started Vent Installation Acid and Standard Base Cabinet To ventilate the Acid Storage Cabinet and the Stan
27. vailable Contact Labconco Corporation for ordering Self Closing Doors for Solvent Storage Cabinets S 9914700 Self Closing Solvent Left Hinged Door Kit 9914701 Self Closing Solvent Right Hinged Door Kit 9914702 Self Closing Solvent Double Door Kit Appendix C Storage Cabinet Accessories Filler Panel Kits 9920300 Panel Filler 24 for Interior depth Protector XL Fume Hood 9920301 Panel Filler 30 for Interior depth Protector XL Fume Hood AJ 9920302 Panel Filler 36 for Interior depth Protector XL Fume Hood 9920303 Panel Filler ADA 24 for Interior depth Protector XL Fume Hood 9920304 Panel Filler ADA 30 for Interior depth Protector XL Fume Hood 9920305 Panel Filler ADA 36 for Interior depth Protector XL Fume Hood 9920306 Panel Filler Protector Fume Hood 9920307 Panel Filler ADA Protector Fume Hood Individual kits contain one filler panel filler panel angle and mounting screws Appendix C Storage Cabinet Accessories 46 APPENDIX D Quick REFERENCE STORAGE CABINETS SOLVENT ACID 48 9902000 9901000 36 9902100 9901100 30 9902200 9901200 24 9902300 9902400 9901300 9901500 18 9901400 9901600 12 48 w Self Closing Doors 9903000 X 36 w Self Closing Doors 9903100 30 w Self Closing Doors 9903200 24 w Sel
Download Pdf Manuals
Related Search