User manual
Contents
1. User manual SS the cable into the HDMI socket on the receiver and the other end into the matching socket on your television In this case you do not have to make audio connections because the HDMI connector can output stereo audio or Dolby digital audio 2 Connect one end of SCART cable to the TV SCART jack on the back of the receiver and the other end to a SCART jack on your TV 3 Connect one end of RCA cable to the RCA jack on the back of the receiver and the other end to a RCA jack on your TV Finally connect the coaxial cable from the operator to the RF IN jack on the receiver NOTE Receiver may be equipped with one of two RF IN jacks e Connector IEC 169 24 type picture A colloquially called F This connector provide constant solid connection between signal cable and receiver e Connector IEC 169 24 type picture B If receiver is equipped in connector from picture A and signal cable is prepared to fit to connector from picture B use adaptor attached to receiver s set picture C Screw it on to RF IN connector and then connect signal cable connector With External Audio Hi Fi System To connect any external Audio Hi Fi system the receiver has been provided with two RCA connectors at the back of the receiver marked with Audio L and R Connect an RCA stereo cable from the AUDIO L R jacks on the back of the receiver to the LINE AUX SPARE OR EXTRA input jacks on your Hi Fi System 102. User manual 9 Basic operations 9 1 TurnonSTB First press the O POWER to turn on the unit When the STB is first used there will play the first channel from the default Channel List If the STB is not first used STB will play the same channel as last time before turning off Frequently Asked Question Q The power of my STB has been turned on and not in Standby mode but the TV screen showed nothing A Make sure the TV set has been set to the correct video input not the TV channels For example if you have connected the unit with the Video1 input of the TV set the TV set has to be switched to Video 1 Q The power of my STB has been turn on and not in Standby mode but the TV screen showed nothing except popup window with No Signal information A That means the channel which you select is no signal Check connection of signal cable or contact operator 9 2 1 Press O POWER Key can enter the Standby state Power 2 In Standby state press O POWER Key again can call back the unit and go on play the previous channel 3 User can also disconnect the device s main power to end the Standby state 9 3 In full screen press 1 4 to change channel Channel Up Channel Down 9 4 Volume Up Volume Down In full screen press lt gt to adjust volume 9 5 Number In full screen use number key and press OK on the Remote Control Unit to change channel 9 6 Mute 1 Press L
3. RaDio Receiver switches between TV and Radio mode ZOOM Press Q key select zoom times from X1 to X16 PREVIOUS Return to the previous menu or status d aubio Audio channels setup to select audio mode Left Right Stereo TV RCV Receiver switches between TV and receive mode 1 INFORMATION To display channel status or various program information of current service EPG Electronic Program Guide Display the Programs guide on screen when available MENU Displays the Main Menu on the screen or return to the previous menu or status EXIT Cancel the user selection and return to the viewing mode from a menu OK To select menu option or to updated on entry lt KEYS To adjust volume level or to move cursor left or right in the menu TN KEYS To change channels or to move cursor up or down in the menu P P To move up the cursor to the next or previous page in the menu or channel list RED KEY Has different functions per menu GREEN KEY Shows teletext information of the current channel supports vetLow KEY Subtitle Display BLUE KEY Has different functions per menu UHF In case your TV is connected through RF Modulator UHF select output channel number between CH21 and CH69 with up and down key optional FIND Use to prompt find channels sort by character SLEEP Press sleep key to switch between Sleep Timer Off 10 30 60 90 120 minutes P N WHITE KEY Press P
4. button to Fast Backward or Fast Forward 6 You can press I or Il button to Slow Backward or Slow Forward 7 Press lt or gt button to jump to different position then press OK button to confirm 8 Press W button to stop the recording 9 26 Exit Press EXIT key can exit the current menu to last menu or close the window User manual 10 Menu Service When you press Menu key to enter menu there will display the picture like below 1 Press T key to select menu pages among Service Installation Preference System Game Conditional Access USB and Internet optional 2 Press OK key to enter the selected item Game 3 Conditional Access In Service menu 1 Press T key to select menu items among Organizing Services and Organizing Favourites 2 Press OK key to enter the selected item 10 1 Organizing Services When you enter to Organizing Services menu there will display the screen like below 1You can move highlight by press T J keys to preview the current highlighted program in the right side preview window 2 You can press P P keys to implement the Page Up Page Down function 3 You can use lt gt key to switch between list of channels and list of channel edit functions Move Lock Delete Rename Skip 4 Press color key can implement the corresponding function Group Options Find 5You can press Exit key
5. Max 12W 5 C 45 C 10 C 70 C 5 95 RH non condensing lt 1 5Kg 220 W x 160 D x 40 H mm 4Digits IEC 169 24 Female optional IEC 169 2 Female IEC 169 2 Male 9 pin D Rs232 DCE serial port TV CVBS RGB Composite Video CVBS Audio left Audio right coaxial Digital Audio Output 1 slot USB 2 0 VER 1 2 Type A RJ45 Weight and dimensions are not absolutely exact values Specifications are subject to change by manufacturer without notice 31 User manual SS 20 Declaration of conformity The manufacturer herewith declares the conformity of that product with the following directives and standards Low Voltage Directive 2006 95 EC EN 60065 2002 A1 2006 EMC Directive 2004 108 EC EN 55 013 2001 A1 2003 A2 2006 EN 55 020 2007 EN 61 000 3 2 2006 EN 61 000 3 3 2008 Model Digital Cable Receiver DVB C CE 32
6. N button to switch the display mode among AUTO PAL PAL M PAL N NTSC HDMI 576i50 HDMI 480160 HDMI 576p50 and HDMI 480p60 FAV FAVORITE To set receiver to the favorite list mode display actual favorite channel list a ARCHIVE Press this button to enter the File Manager File list menu directly TMS Time Shift Press this button to display Time Shift info bar User manual SSS IA P Play To play the JPEG or recording file E Stop To stop JPEG player recording file Time Shift or playback Il PAUSE Used to select the freeze function Press once to freeze the screen picture Record To start recording 4 Fast Backward To start Fast Backward function PP Fast Forward To start Fast Forward function all Slow Backward To start Slow Backward function l Slow Forward To start Slow Forward function F1 Reserve 6 Front panel Card Slots Display POWER To switch the receiver power on stand by MENU KEY To enter into the main menu E gt To adjust volume level or to move cursor left or right in the menu Y y To change channels or to move cursor up or down in the menu OK KEY To see TV Radio channel list or to confirm in the menu Remote Sensor Detects infrared signal from remote control unit Power Led Lights up while the receiver is power on Signal Led When receiving signal is strong the signal led is lighted LED Display Indicates operating status of receive
7. The level of Signal strength is low No sound RCA cable is connected incorrectly The Volume level is low Muting function is active No display on the LED Display The power cord is not plugged in correctly Panel optional No picture on the screen Receiver is in Standby mode RCA Jack is not connected firmly to the video output port of television Incorrect channel or video output is selected on television Brightness level of your TV set is incorrectly defined 30 User manual 19 Specifications General System standard Frequency Range Signal Level Bandwidth Demodulation Constellations Input Symbol Rate A V Mode Video format Audio format Aspect Ratio Audio sampling rate Audio Type Graphic display Microprocessor amp Memories Main processor Flash memory RAM memory Power amp Environment Condition Supply Voltage Supply Power Operating temp Storage temperature Storage Humidity Physical Specification Weight Dimensions LED display Connection RF input RF OUT RS232 Scart Video Audio S PDIF USB HDMI Ethernet Optional Fully MPEG4 H 264 DVB C HD Compliant 47 862MHZ 20dBMV to 20dBMV 8MHz QAM 16 32 64 128 256 1 5 7 Ms s MPEG II Main profile Main level MPEG II layer 18 11 AC3 16 9 4 3 LB 4 3 PS 32 44 1 48kHz Mono Dual Mono Stereo Joint stereo 720x576 PAL 720x480 NTSC 1280 720 1920 1080 HDTV 396 MHz 32 Mbit 1024Mbit 100 250V AC 50 60Hz
8. a period of 3 hours after the last active use In practice this means that if during this time the receiver will not be given any command by using the remote control or keypad on the front panel the receiver turns off Turning off the receiver will be preceded 2 minutes previous by a relevant message appears on the TV screen Please also note that this feature is enabled by default but at Your own request You can disable it using the appropriate functions in the receiver menu 3 2 Working with external USB drive only for receivers with USB connector e During the selection and operation with USB drive hard drive flash memory user should pay attention on e Drive is compliant with USB 2 0 and have the appropriate parameters of read and write speed e Drive contain single partition formatted in a supported format e If necessary especially for USB hard drives which are characterized by a high power consumption drive should be supplied from an external power supply e Do not disconnect during a write read data operation e Do not use very full or fragmented drive Mismatch above recommendations may result in incorrect operation of the devices and in extreme cases can cause damage The manufacturer takes no responsibility for any damages directly or indirectly caused by loss of recorded or edited data stored on an external USB drive which was connected to the receiver and gives no warranty for any other data on the USB drive
9. key to enter full screen playing mode 12 2 Parental Control You can set a password for anyone who wishes to operate in the Installation menu And you can also set the password for the lock channels How to set the lock channel please refer to LOCK Here will show you how to setting and how to revising the password 1 In Parental Control function press OK key there will pop an dialogue for you to input the password When you input the correct password you will see a screen like below 2 Menu Lock determining that when user wish to enter Installation menu whether have to input Password or not If the setting of Menu Lock is Yes which means user have to key in password set No means unlock 3 Channel Lock determining that when user wish to play the lock channels whether have to input the password or not lf the setting is Yes play the channels with lock mark will show up a dialogue on the screen and ask for the password If the setting of Channel Lock is No the Lock function will invalid 4 New Password is used for revising password you can input the new password in this item by using number keys directly After you filled in 4 digital numbers the highlight will auto skip to Confirm Password and ask you to input the new password again If the password is correct the screen will show up a message of Change password successfully 5 You can pre
10. to enter full screen playing mode 10 1 1 Move You can reorder and move the service to the preferred position Mark the desired services using OK button use gt button to choose Move mode and press OK button then useT Y buttons to move and press OK button to confirm 10 1 2 Lock You can restrain and lock the services Mark the desired services using OK button use button to choose Lock mode and press OK button to confirm 10 1 3 Delete You can delete the services Mark the desired services using OK button use gt button to choose Delete mode and press OK button to confirm User manual 10 1 4 Rename Mark the service you want to rename use gt button to select Rename item and press OK button to display keyboard and rename it After renaming it press OK button on keyboard to save 10 1 5 Skip You can restrain and Skip hide the services Mark the desired services using OK button use gt button to choose Skip mode and press OK button to confirm 10 1 6 Group RED It is very useful to select services with different Groups 10 1 7 Options GREEN It is very convenient function to Mark the desired services with different options 10 1 8 Find Q It is an item to locate certain service by name button to display the Find submenu use keyboard to enter service name and quickly Press press button again to select the desired se
11. ways 4 Press GREEN key to recall shortcut to EPG actual event details 13 User manual ROT PA HOROSK oP AUTO 01 02 9 18 Subtitle 1 Press veow KEY key in full screen you can switch subtitle on or off Cudedie 4 Subttle_Languaga OFF 0001 2ITV T 0002 ZJTV 0002 2DF 0004 ZDFinfokaral 0005 ZDFdokukanal 0006 ZD0Fthemercaral 1 Press 4irinoy key in full screen can open the Find window You can press E Channel Up Channel Down Volume Up Volume Down key to move highlight and press OK key to input the selected symbol or letter into the dialogue 2 After input each character the program list on the left will search the channel according your input and list the matched channel 3 Move highlight to OK and press OK key can close Find window and you can select channel from the channels list directly 9 20 Zoom 1 The A zoom key allows you to magnify a certain area on the images 2 Press A zoom key again the image will enlarge rotate as x1 x2 x4 x6 x8 x12 x16 3 In x2 x16 mode using 11 keys to move the image center area you want to see 4 In zoom mode press EXIT to close Zoom window 9 21 TV RCV 1 Press Tv rcv key can switch between TV mode and STB mode 9 22 Menu 1 Press MENU key can open the menu exit the current menu to last menu or close the window 9 23 Video Format 1 Press P N WHITE KEY key unde
12. when case of abnormal function receiver will happened User manual SS 3 3 Battery installation A To install the batteries in the remote control remove the flap protecting the battery C D compartment see Fig A slider type push and o slide B latch type lever the latch and pull the fold If inside the chamber there are used batteries they must be removed Then put new a N batteries inside When installing the battery pay E special attention on the polarity the direction of insertion of both batteries The correct polarity of batteries is drawn on a description inside the y battery compartment in the remote control After NL P4 installing the batteries place protecting flap on its mp original position Service life of batteries e The batteries normally last for about one year despite that it depends on how often and in what way the remote control is operated e If the remote control fails to work even when operated near the DVB receiver replace the batteries e Use size 7 AAA batteries 2 pieces WARNING Do not use rechargeable Ni Cd batteries Do not attempt to recharge short circuit disassemble heat the batteries or throw them into the fire e Do not drop tramp or impact the remote control This may damage the parts and lead to malfunction e Do not mix used battery with new one ever when using e If the remote control shall be spared for a long time remov
13. PES EU OO UE PES OOO OR BR RO O E CO PRO POR OO NESNESE EKES NESNESE VERENNE EWERS NEEE NEEN 31 Declaration of cono Mun a A A AA A A A AA A eaten 32 User manual 1 Safety precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with Warning The exclamation point within an arrowhead symbol within an To reduce the risk of electric shock equilateral triangle is intended to equilateral triangle is intended don t open the cabinet Refer alert the user to important to alert the user to dangerous servicing to qualified personnel only operating and maintenance voltage and to prevent from a servicing risk of electric shock WARNING Do not use this STB where contact with or immersion in water is a possibility Do not use near flower vase washbowls kitchen sinks laundry tubs swimming pools etc WARNING Do not put the candle or lamp stand on the cabinet otherwise there is the danger of fire WARNING The unit should be connected to a power supply only of the type described in the operating instructions or as marked on the unit If you are not sure of the type of power supply for example 120 or 230 V to your home consult your local dealer or local power company WARNING This product install diodes Do not open the cabinet or touch any parts in the inner mechanism Consult your local dealer for technical service if the opening is required Note To ensure proper use of this product ple
14. User manual High Definition Digital Cable Receiver Model ID Cab HD 220 5 2010 jp Contents 1 2 3 ahh teed ES O 00 N O UI ea 12 1 12 2 12 3 12 4 12 5 12 6 12 7 13 13 1 13 2 13 3 13 4 13 5 14 14 1 14 2 15 1 o jiciisinisiianisin ne aaar a ne a a a ERARE KEREKAN RE 1 Environment Protection sorier eesse raserer EEE EE IES ENEE e SEPIE EEEE EEEE EVE EE EEPE ERE EE 3 O 4 Automatic POWEr DOWN iiccomiisiientaiecenn sesh cad veloeatuenescauauteseducauedsaunealscecnadussesdeabsdieasnubs edd ceadedaccnuseddeusasdueensasendeabdderueauasess eataatestely 4 Working with external USB drive only for receivers with USB CONNEctor cccccccccccncnnnnnnnnnnnnnnonnnnnnnnnnnnnnnnnononnnnnnnnnnnnnnnnnininess 4 Battery installation ci ri 5 EU OS ii AAA A AA AA AAA AA AAA AA AA AAA a 6 A A An 7 A nn Ro AAA Pa 8 Rear panel sir L EE E E E E E E E E E E E E E E E E EE E E E E tan 9 CONNECTING YOUF Syste Secdcccecicecdscvcs ccceecovesteectbectincusevaesssccubecteessiscatetocedeusdseesasecewecduedsiseedstseecdoedavesesessbecdosdetessiscieuceandcbestiexsueciantesesseye 9 E AA O 11 TUM OMS VB isc nian atleti 11 POWOM POCO PE RN 11 Channel UNED Want atnicu rare icia 11 Volume Up Vol me DOWN ninia rana ano 11 ALE py 1 ennnen EAE E AEE E ENEA NE ad ese ce ee ee eee 11 MIS ida A AA A AAA EA AA AA E AA 11 PUSO ies 11 A A 11 A cegeatgeneaeadRiacuedsnedeceseeeauteahauslonsetecneaboerecca lee echaauerehcalhe
15. ack by press T W key and modify the audio mode by press lt gt key 3 Mode Left Right Stereo Mono 9 11 Information In full screen press Z inrormarion key can open information screen in the window shows the parameters of current channel 9 12 EPG 1 The STB has an Electronic Program Guide EPG to help you navigate channels through all the possible viewing options The EPG supplies information such as channel listings and starting and ending times for all available channels Press EPG key to display Program Guide 14 00 14 56 LA 3015 00 aL SO 1345 1930 14 00 15 36 0075 MSO COMEDY 0027 HBO Page Select ee A Timer Record 2 Press OK key in each item can see more detail information ES Grange Sport 14 30 1430 16 30 Top Volley Top V Top Volley international meer TVC Amstetveen Dvi Urdewer Veli 47400 Top Volley international mecz TVE Amstetreen cong Unilever Velel A Wedrowcy z Semt 1400 1436 Europese Nagrod 3 Press RED key to open the Group window You can press T J key to move highlight and press OK key to select group of channels 4 Press GREEN key to open Options window You can press T J key to move highlight and press OK key to select EPG events display mode Now EPG Next EPG More Schedule User manual SS 5 Press YELLOW key to enable shortcut to channel parameters edition 6 Press T key
16. ame e EXIT Quit game and draw back to Game menu 17 3 Othello 1 Moving highlight to Setup and press lt gt keys to select the game level degree of difficulty 2 Moving highlight to Start and press OK key to start the game 3 Moving highlight to Cancel keys and press OK key to draw back from the game Start on the game e lt T use these arrow keys to guide chessman e OK set chessman EXIT Quit game and draw back to Game menu User manual I M 18 Trouble shooting If you suspect there is a fault with your receiver please check the following trouble shooting guide before calling authorized service agent Warning Under no circumstances attempt to repair the receiver yourself Tampering with the receiver may result in fatal electric shock and will invalidate your warranty Symptom Possible cause Settings you made in the menu have not The receiver lost power before being able to enter into standby mode change Some of the Settings saved by user can be deleted partly or fully No signal The level of signal is weak The cable is incorrectly Connected short circuit or open circuit Receiver is on but no picture or sound Channel is not available except the following messages NO TV program Channel is scramble Receiver not responding to remote control RCU batteries are dead or inserted incorrectly unit The RCU is pointing toward wrong direction Poor picture Quality
17. ase read this User manual carefully and retain for further reference Note This product install diodes Do not open the cabinet to avoid the unit direct exposure to radiation Unit Cleaning After the unit power is turned off you can clean the cabinet panel and remote control with a soft cloth lightly moistened with a mild detergent solution Attachments Never add any attachments and or equipment without the manufacturer consent as such additions may result in the risk of fire electric shock or other personal injury User manual SS Locating Slots and openings in the cabinet are provided for ventilation to protect it from overheating Do not block these openings or allow them to be blocked by placing the STB on a bed sofa or other similar surface nor should it be placed over a radiator or heat register Power Cord Protection Place the power supply cord out of the way where it will not be walked on Please take special attentions to cords at plugs convenience receptacles and the point where they exit from the unit Object and Liquid Entry Never put objects of any kind into this STB through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill any liquid on the STB Note Moisture may be formed on the lens In the following conditions when the unit is suddenly moved from a cold environment or an air condition room to a warm place
18. e the batteries Otherwise electrolyte may leak which may lead to malfunction even fire accident when some substance contacts with the electrolyte e Wipe away the electrolyte having leaked inside the remote control and replace with new batteries e If any electrolyte happens to touch some parts of your skin wash it off thoroughly with clean water immediately User manual FE OI II ss 4 Features e MPEG Fully DVB C HD compliant Multilingual menu text support e Fast channel switching e Channel list editing e Favorite channel list editing Electronic Program Guide EPG for on screen channel information e Teletext supported by VBI insertion and software emulation e Subtitle supported e Parental lock facility by channel and program event e HDMI HD Video Audio Output e S PDIF for digital audio or Dolby digital bitstream output a LAN 10 100 Mbps Ethernet optional e Software update via LAN port optional USB 2 0 Host e Time Shift Video Recording e Exciting games embedded User manual SSS 5 Remote control You can power on off the receiver operate on screen menu and use a variety of hot key function Depending on configuration one of two remote controllers may be attached to receivers set O POWER To switch your receiver on from standby or standby to on aK MUTE Used to enable or disable the audio NUMERIC KEYS 0 9 Used to select channels or enter programming parameters EVA rv
19. ed above 2 Aspect Mode is for switching the screen aspect ratio mode Now we provide below options 4 3 PS 4 3 LB 16 9 Auto You can press lt gt key to select each mode circularly 16 9 will provide user pillar box mode it means user use 16 9 TV to display but need to see a 4 3 full display picture System will force press wide screen picture to be narrow and there re black band on left and right site Auto means system won t do any aspect ratio translation 16 9 picture source will be good display on a 16 9 TV but will be too narrow on a User manual 4 3 TV and 4 3 picture source will be too wide in a 16 9 TV but will be good display in a 4 3 TV 3 Video Output Press lt to select CVBS or RGB 4 RF system and RF channel optional are for user to set the TV RF modulator output signal VHF UHF channel and TV system mode If your TV is too old to supports CVBS RGB HDMI you can use TV RF cable to connect STB s TV RF output port to TV Antenna input port optional 5 Digital Audio Out is for setting the both SPDIF and HDMI s digital audio output mode it has LPCM Out Auto Left Right Key to select each mode circularity options You can press LPCM Out means system will decode no matter AC3 or PCM audio track data to be LPCM digital audio decoder or HDMI TV will get LPCM digital audio data Auto means system will detect which the connected HDMI TV can decode and then output that data If HDMI TV ca
20. eesaaaggasss 22 AS O NN 22 M nu Systemi AA PI E PES PUERRO N 23 O E et amud Abe E A dts wale stanae Malian E E dts E A EEE A EEEE 23 Default setting EEE A E EAA E EE E EAEE AAA EENE A 23 SOME upgrade A AE EEEE EAEEREN E E EEEE amin NE E E EAEE AEAEE E EEEE EEE E A EA 24 Upgrade By USB unciis ee dd 24 Back p to USB gare ni dina 25 Menu Conditional ACCESS sass vissscaucsisccunceusaduncsustau neni seninesdscaaycosnaduncnustaunaasnanincsdsaaancassadancnsstaancassankncadsudauenssadancnistdaneusseaancadsudaneaanads 25 CAS CUEING Ciir caidas cde Se oie A A a ad aa iaa n 25 Common Interface Optional icine EAE EAE 26 PS pri AAA en a cea aaa ee em a aera 26 O beet ce Leet ee Lead oat beauties bee dice Lbcent ce lee Goce E A AET 26 Record WANA BOR brida 26 Storage IMormatoN ned ct eens cei redid pac eed ee ee ee EA ae 27 PUR SNE A EKAS EKARTE EKANA EKNE 27 USB Speed TCS Eran ocaniutessaranaensannianssinii derengeni neta anea it aatas aeta aae ai aa ara aesa aaee ii Sanana cent arse aage E aeaio 27 Menu Internet Opt rin AAA AAA RNA AAA AAA 28 Network Local Set tints inniinn annaa duce ued eeu tace A EE N E duoc umedbteutace A REENE N N S NEA TENS 28 Http Upgrade vivacidad ii iii E ETETEA 28 ee eee ee ee ere EEE EEEE EES 28 TEIS si a Ire iii 28 A A o q UnA ue ad mca ee ee ae A 29 AA erg aiu ah E Sry Saag gn Ss Se ag Gag ng ea Pound Soa ay E E anes 29 ToublesSho00 RN A AAA AAA AA AA 30 ha el 1 1018 18 11 APPO PORRO UPRO EU O
21. efault password is 0000 After you input the correct password there will show a warning message to inquiry you The operation will load default and erase all the channels that user added continue User manual ote 146 Peet _ Thie Operation wil load defaut end erase all the channels that user added continue Vee If you select Yes option the all revised parameters of the receiver will reset to default value Please carefully to using this function In step 1 and step 2 press EXIT key can draw back from this item and without saving 2 When you press OK key in the Delete All Channel you will see a screen like below tipies amp be e Are you Sur to Gelete si Yes If you select Yes all channels will be deleted In step 1 and step 2 press EXIT key can exit the function directly without save Frequently Asked Question Q IF incautiously delete all channels what should do A There are two ways to restore To re search all channels in Installation function Use Default Value function to restore all channels in Tools function 13 3 Software upgrade 1 We offer the functions for user to connecting receiver Master to the other receiver Slave via serial interface 2 Connect master receiver to slave receiver via serial interface Enter Software Upgrade menu in master receiver and press 1 keys to switc
22. et Mask Gateway and DNS options become enabled You have to set these options according to your IP address 16 2 Http Upgrade 1When connected to the Internet receiver can manually or automatically make software update from file from server Note This function depends on connection with external server In case of no software on server this function will not work 17 Menu Game AAA MT A Preference System Tara Candtional Accecs Otneso JEG When you enter Game menu you will see three Games include Tetris Snake and Othello Basic operation statement 17 1 Tetris 1 Moving highlight to Setup and press lt gt key to select the game level speed 2 Moving highlight to Start and press OK key to start the game 3 Moving highlight to Cancel keys and press User manual OK key to draw back from the game 4 Start on the game e lt gt Move shape left or right e Rotate clockwise e J Faster drop e OK Pause Play the game e EXIT Quit game and draw back to Game menu 17 2 Snake 1 Moving highlight to Setup and press lt gt key to select the game level speed 2 Moving highlight to Start and press OK key to start the game 3 Moving highlight to Cancellkeys and press OK key to draw back from the game Start on the game 29 e gt 7 4 use these arrow keys to guide the snake e OK Pause Play g
23. gegcbaneiudedaaeavecsnuadtuee oxtaeqeauaesencalacaeheasneasheataGanaestae 11 A A O O 12 Informatio Minin a ETER EAE TETE E E a bees tae EEEE ATETEA EEEO ETEEN 12 A sens acest ec A E eet A E eames oetieder Geeta 12 TV RADIO iscsi decides A Spud Sa dacs O aE a a mG GU E AE K A aaia 13 A E atte A e agi i ae cee emcees 13 A icc ca ce gcc cae ca a can ck een rd iio 13 A eases ninco ec nn nea eee aa easel ceeded anda Lae ear I 13 O a a aneas 13 A A A AN 14 O A O 14 LODO tE E A E AAA AE DE ALA A AAA A A AAA 14 VOR 14 A ON 14 A 14 A pede sh O E e Un nn E E E 15 A A A Gaya nepeasuuaeeaaseas 15 A A E A 15 A en 16 a coscasicnvededeceeeeuacsauvdeecueevscnadauvesdadievecactiuedeacea E ucatuaueded tue deena sweats sue cdeamenec dean sacdbavececchanveadsecoeansecdee 16 Organizing favorit S ici dd alc deiuucsdeadeedce dvduulsdavdeeldn tossed EAER ELAO EN doce adaacdaebdsdetoativaess see 17 A A 17 Cable sali it 17 Menu Preferentes erscmislctceeniodsics ec scaaselisceavewbeaaiveasdaasanabscaanalsscaaneubucaircassaasneabscaanelsaaseubncaicassaasneabscaanctineaaseaads 18 QING Wa Or ir EE E OE E E ias 18 Parental AT idad liada access 19 PURVES ODUIN o desman cada sdewes dd ewan cosa E E Jeevan coda A A A A A A E E E EEE 19 MMA Cava ren a E E A E E E A A E E E a E E 20 nn E A E N A E cateeceei ce 21 Miscellaneous Settings ccceescccccccccessseeseeeeeeeeeeeaeeeeeeeeeeeeeeeaeeeeeeeeeeeeeeeeaseeeeeeeeeeeeeeesaeeeeeseeeeeesesaeeeaseseeeeesesssueausseeeeee
24. h upgrade mode 3 Upgrade modes include Code Program List User Back Video Back Radio Back DefaultBD Default DB User DB Program Code 4 Moving highlight to Start on master receiver and press OK key to start upgrade 5 Turn on slave receiver and it needn t operate any setting Press EXIT key to draw back 13 4 Upgrade By USB User manual In this menu you can upgrade the software from USB conveniently press OK button to enter ALOOSE 04000250 gisbo Sofware no Channel hat Ts In this menu you can select the Upgrade Mode among Software no channel list Channel list All SW bootloader All SW Channel list You can select the appropriate upgrade file on Upgrade File item After you select the Upgrade Mode and Upgrade File press OK button on Start item the receiver can upgrade automatically NOTE You must put the upgrade file on the ROOT DIRECTORY of the USB storage 13 5 Backup to USB In this menu you can dump the software to the USB equipment In Backup file you can press OK key to edit the file name In Backup to USB you can press OK to start dumping software 14 Menu Conditional Access 1 When you enter to Conditional Access menu you will see a screen like below 14 1 CA Setting Receiver provide one CA slot for user to use Receiver has build in smart card module with CONAX system By using cards in this sys
25. he smart car button Then select the File System between the EAT and the NTFS Press OK button to format of recorded file confirm 15 5 USB Speed Test MED Speed Test Standard speed 120sd 160hd 140 sd tms USB speed 4 Record Type This function enables to choose file 200M Bite s 173M Bits s Current status HD TMS Current support one HD channel record and one HD channel timestyvtt The USB speed wil a ittie slower wth the fies increasing Exit Note If you format the HDD all the files include JPEG and the record files will be deleted from the HDD In USB Speed Test menu you can see the Standard speed and your USB hard disk speed according this information you can know what 2 1f you want to change HDD function between Record Timeshift and REC amp TMS both previous e 27 operation your disk can support User manual 16 Menu Internet optional If you enter to the Internet Menu you will see the picture like the below Ea n razallatron Preference System Condasomal Access You can get a new software from the network via LAN port 16 1 Network Local Setting 182 168 005 192 HA 266 262 000 122 100 005 003 122 100 003 250 192 160 006 249 1 In this menu you may assign a dynamic IP address to the digital receiver To do so select the DHCP On 2 1f you have a static IP address unselect the DHCP Enable then the IP Address Subn
26. immediately after a heater has been turned on ina steamy or very humid room If the moisture forms inside the unit it may not operate properly To correct this problem turn on the power and wait about two hours for the moisture to evaporate Parts Replacement When the unit parts need to be replaced user should make sure the service technician use the replacement parts specified by the manufacturer or having the same characteristics as the original part Unauthorized replacement may put the unit In the risk of fire electric shock or other hazards Safety Check After all the maintenances and repairs are done user is required to request the service technician to conduct the overall safety check to ensure the machine is In the proper condition User manual 2 Environment protection Attention Your product Is marked with this symbol It means that used electrical and electronic products should not be mixed with general household waste There is a separate collection system for these products Information on Disposal for Users private households in the European Union Used electrical and electronic equipment must be treated separately and In accordance with legislation that requires proper treatment recovery and recycling of used electrical and electronic equipment Following the implementation by member states private households within the EU states may return their used electrical and electronic equipment to de
27. l display position of the info bar in full screen mode You can choose bottom or top 3 05D Transparency You can set the transparency of OSD You can press lt gt key to select the values There are 5 levels of transparency 10 22 User manual 20 30 and 40 and off means no transparency function 4 Load OSD Setting Default If you are not satisfy with your setting you can move highlight to this item and press OK key to reset parameters as default value Press EXIT key to draw back from the OSD Setting menu 13 Menu System When you enter to System menu you will see a screen like below In Tools menu 1 Press T W key to select menu items among Information Default Setting Software Upgrade Upgrade by USB Backup to USB 2 Press OK key to enter the selected item 13 1 Information 23 _ _ a MOD EL ID S W VERSION HWW VERSION LOADER VERSION LATEST UPDATE tte N STR O LED Vermon 1 When you enter to Information menu you will see a screen like above The screen displays software loader and hardware information 2 Press EXIT key to draw back to Tools menu 13 2 Default setting 1 When you enter to Default setting menu you will see a screen like below 1 When you press OK key in the Default Value item there will appear a dialogue box for you to enter the password and the d
28. lay like below Wakeup Message Press lt gt key to select reminding message as Birthday Anniversary and General Date You can use number key to input your wakeup date On Time Use number keys to input your wakeup time Once the times up no matter what the system is in standby mode or in playing mode the reminding system will automatically pop a message The message will always display on the screen you can press EXIT key to close it Press EXIT key to exit the current menu 12 5 A V Control When you enter to A V Control menu you will see the screen like below 1 User can switch display resolution in view mode using P N WHITE KEY button Also Display Mode is for switching the system outputting video resolution Move highlight on it and press left or right key it will switch video resolution circularly by the sequence by source lt gt by native TV lt gt 480i lt gt 480P lt gt 576i lt gt 576p lt gt 720P lt gt 1080i By Source means system will set the video output resolution according to the program it s playing different resolution programs switching perhaps will makes TV screen flickering By Native TV means system will be according to the HDMI TV s max supported resolution to set its resolution if system is not connected to a HMDI TV it will set resolution to be default Depending on selected resolutions may be video output available different than list
29. n decode AC3 system just output RAW data if HDMI TV can decode LPCM only system will just decode AC3 or LPCM to be LPCM and then output 6 Press EXIT key to draw back from A V Control menu 12 6 Miscellaneous Settings When you input to OSD Setting menu you will see a screen like below 1 Subtitle Auto You can press lt key to select On or Off If the current channel has subtitle information it will be showed up while this function is On If this function is Off there won t show up subtitle information even if the current channel has subtitle information 2 Auto Power Down Enables to set time of automatic power down of receiver when user not use any front panel and remote controller buttons 3 Panel Power In Standby Enables to decide about front panel in standby mode On will display clock with actual time Off will display only red Power LED 4 Loop Control Enables to activate deactivate loop function of tuner in standby mode 12 7 OSD setting When you input to OSD Setting menu you will see a screen like below 1 0SD Timeout When you switch channels in full screen there will show up some information about current channel on the lower of the screen And the information show up on the screen you can press regarding to duration of these gt key to set the time The range of the duration is 1 10 seconds 2 Position contro
30. numeric button of the RCU 3 You can input the Second Frequency by use the numeric button of the RCU if you set the Scan Mode to Blind Scan 4You can input the Symbol Rate by use the numeric button of the RCU 5You can select the QAM value 16QAM 32QAM 64QAM 128QAM and 256QAM 6 You can turn ON or OFF the NIT Search if you set the Scan Mode to Manual Scan NIT ON makes possible to scan additional frequencies described among by operator in scanned frequency signal 7When you complete your modification press OK button on Search item to enter Scan menu and then press OK button it will begin to scan 12 Menu Preferences When you enter to Preferences menu you will see the screen like below In Preferences menu 1 Press T W key to select menu items among Language Parental Control Time setting Timer A V Control Miscellaneous OSD Setting 2 Press OK key to enter the selected item 12 1 Language When you enter to Language menu you will see the screen like below M Menu Language Enga Frat Audio Secong Aude Audio Pronty CPG Subtdle Language Tebetest 1 Menu Language Press lt gt keys to select OSD menu language 2 First Audio Some channels have more than one audio language for choosing by this function you can set the first audio for this channel If the playing channel has the same audio as the First Audio you set system will play this a
31. o set Timer number and there are 8 timers in total 3 Timer Mode There are several modes for Timer include Off Once Monthly and Yearly to setting Daily Weekly 4 Timer Service There are five options for Timer TV Channel Radio timer setting for channel change and Service include and Channel Wakeup Sleep and Record Radio and Record TV Timer setting for Record the TV or Radio program to USB Hard Disk reminding message and Message 5 When you select Channel timer setting for channel change and wakeup option in Timer Service the screen will display like below Channel Press OK key to enter channel list and select channel that you want to setting 20 User manual Date Use number keys to input your wakeup date On Time Use number keys to input your wakeup time Once the time s up no matter what the system is in standby mode or in playing mode the system will automatically switch to the channel you want and start to play 6 When you select Record option in Timer Service On Time function enables to set time of begin event planned to record Also additional functions become active Duration Enables to set time of duration of event planned to record Standby After Finish Enables to set state of receiver after recording event 7 When you message option in Timer Service the screen select Message reminding will disp
32. r Card Slot Smart Card Interface for CONAX cards Insert the smart card chip side up Common Interface Socket for Conditional Access Modules CAM optional User manual 7 Rear panel Please refer to the diagram above for all possible connections of your receiver Do not connect the unit to the mains socket until all other connections have been made and checked RF IN This port is to connect the coaxial cable from Antenna Socket RF OUT This enables the connection of another receiver R L AUDIO OUT These RCA connectors are used to connect any external audio amp or system CVBS This RCA connector is used to connect any external video S PDIF This RCA connector is used to connect external digital audio system TV This is used to connect your TV through SCART cable HDMI Audio and Video output socket for TV set with HDMI Input Jack only USB USB 2 0 Host connect to USB hard disk or flash disk RS 232C This is used to connect your receiver to a computer through a serial cable Ethernet Network port you can get a new software updates from this port Optional POWER To switch ON OFF the receiver power supply 8 Connecting Your system Cable TY Socket BEEBE There are three ways to connect the receiver to your existing TV system We recommend using one of the following cases for the best result 1 If you have a high definition television set you should use a HDMI cable for best result Plug one end of
33. r Full Screen playback for 1 it will show the current system outputting video resolution continuously press User manual this key system will switch its outputting video resolution by sequence by source gt by native TV gt 480i gt 480P gt 576i gt 576p gt 720P gt 1080i 9 24 Time Shift 1 1f you connect the USB HDD and enable the Time Shift function in the menu Main Menu USB PVR Setting Time Shift it will start the Time Shift function automatically after you switch the program and when you press the Tms button the Time Shift info bar will displayed as the following picture 2 You can press IH button to pause the video and can save the picture to flash by press P button when the video is paused 3 You can press 4 or mM button to Fast Backward or Fast Forward 4You can press 4 or IF button to Slow Backward or Slow Forward 5 Press lt or gt button to jump to different position then press OK button to confirm 6 Press button to exit the playback 9 25 Record 1 If you connect the USB HDD You can press 4 button to start record function as following picture 2 Press button to display the record info bar when you recording 3 Press 4 button again to setting the record time 4You can press II button to pause the video and can save the picture to flash by press P button when the video is paused 5You can press 44 or P gt
34. rvices 10 2 Organizing favourites Greup s AR THE oor TWN Doi TWN Dodd TVH wg Tui isdn poGS TWH 2d ja A Dd Marga 34 Bi Tw METEO iM TWA Tue 7 TWN Sys fied O ioe TY TUS hogy Tw Gre 200 Tru jo TV CHOC D m Test i TWA DDC D me When you enter to Organizing favourites menu there will display the screen like below 1 You can move highlight by press keys in the left and right side list window 2 You can press P P keys to implement the Page Up Page Down function 3 You can use lt gt key to switch between list of all channels at the left list of channel in actual selected FAV list at the right and edit functions in the middle of the screen Add Remove Move Rename 4 Press color key to implement the corresponding function Group Options Find described in previous chapter 5 Press FAV FAVORITE key when cursor is active in left window to choose actual FAV list 6 You can press EXIT key to enter full screen playing mode 11 Menu Installation When you enter to Installation menu there will display the screen like below Cable Installation 11 1 17 User manual Cate inet atarion Manual Scan 474 000 ES JAM No Press OK button to enter the selected item 1 You can select the Scan Mode Manual Scan one frequency or Blind Scan band limited by two frequencies 2 You can input the Frequency by use the
35. s MUTE key to mute the sound and the screen will show up mute OSD 2 Press Ls MuTE key again to restore sound 9 7 1 In playing mode press H pause key the picture Pause will be paused but the sound of the channel will still continues 2 Press H PAUSE key again the screen s picture will skip over to the current playing picture and the sound of the channel will corresponding playing 9 8 Recall Press 2 pREvious key will directly switch to the previous channel that you played before current channel 9 9 Favourite 1 In full screen press FAV FAVORITE key it will display a window of Favorite Group on the left of the screen which you can watch like below lt POLSAT gt 0001 Polen HO 0007 Poles 0003 Poma Fiay 0004 Tyu 0005 RT E 0005 frost Sport Extr 0007 A 0005 TY Blznes 0009 Polsat Neme 0010 omar 2 You can press lt gt keys to select different Favorite Group User manual Pressing P P keys can implement the Page up Page down function 3 Press Exit key to exit the current window Frequently Asked Question Q Why the screen displays No Favorite Channel after pressing Fav ravorITE key A It is because that you haven t set any channels as favorite channel Please refer to Favorite 9 10 Audio 1 In full screen press d aupi0 key can open the Audio window on the screen 2You can modify the audio tr
36. signated collection facilities free of charge In some countries your local retailer may also take back your old product free of charge if you purchase a similar new one Please contact your local authority for further details If your used electrical or electronic equipment has batteries or accumulators please dispose of these separately beforehand according to local requirements By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment recovery and recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due to inappropriate waste handling Information on Disposal for Business Users In the European Union If the product is used for business purposes and you want to discard It Please contact your dealer who will inform you about the take back of the product You might be charged for the costs arising from take back and recycling Small products and small amounts might be taken back by your local collection facilities In other Countries outside the EU If you wish to discard of this product please contact your local authorities and ask for the correct method of disposal User manual 3 Operating notes NOTE 3 1 Automatic Power Down In accordance with actual European Union requirements Your receiver is equipped with function Automatic Power Off It works by switching the receiver into standby mode after
37. ss EXIT key to enter full screen playing mode 12 3 Time setting When you enter to Time Setting menu you will see the screen like below User manual 1 GMT Usage This item is use for open the usage of GMT You can press lt gt keys to switch On Off 2 GMT Offset This item is valid only when the setting of GMT Usage is On You can press gt keys to switch GMT Offset value and the range is 12 00 12 00 increase each half hour progressively 3 Summer You can press lt gt to control Summer time on or off 4 Date and Time items are valid only when the setting of GMT Usage is Off You can press gt 1 keys to move highlight and use number keys to input directly If the current channel provides the correct time information you will see the current time while you enter Time menu If the channel doesn t provide time information you have to input the date and time information manually 5 Time Display This item can control time display on or off on front panel display when full screen play 6 Press EXIT key to draw back from Time Setting menu 12 4 Timer When you enter to Timer menu you will see the screen like below 1 Current time information will display on the first column if the current time is incorrect please modify the time information in Time item 2 Timer Number You can press lt gt keys t
38. t to the receiver this menu is not available 15 1 File List In this menu you can check the files and folders of the USB storage and you can view files from 5 categories Record Image Software All E 1256 1449 015309 IIM No Date Time Channel M0 1256 1449 A OO 18410 1832 Hebei TV 10 06 1401 1821 FujanT 4i 1006 2120 0551 FujanTWi 06 10 14 1830 GTV 2 3 4 5 m j o Telek Delete yr Rename In this menu you can see the record files and you can edit it 1 To Lock the file please press GREEN button 26 User manual ee 2 To Delete the file please press BLUE button press BLUE button 3 To Rename the file please press RED button 15 4 PVR Setting 4 To play the file with small window please press gt button 5 To play the file with full screen please press OK button 15 3 Storage Information Press OK button to enter the HDD Information menu like the below picture in this menu you can see the details information about the HDD 1 Time Shift Enable the Time Shift function 2 Timeshift to Record When this function is turned on when you press the button to record the program it will merge before Timeshifted file with actually recorded file 3 Record as Scrambled When this function is turned on when you play the recorded before scrambled file you must insert the Cl module th t card 1 1f you want to format the HDD press YELLOW and or t
39. tem provided by operators it is possible to watch many scrambled channels coded in this system This menu shows detailed information about card inserted into card reader module It allows inserted according to help messages visible on the bottom of the screen Note All information showed in this menu and submenu are coming from inserted card In case if anything is wrong it could be card problem After inserting User manual the card correctly at any time a message box will show on the screen with message about detecting card info menu all available the card in information will be displayed 14 2 Common Interface Optional We provide one Cl slots for user to use Using different CAM amp cards provided by different CAS Operator you can view many type of scrambled channels In this menu you can see the detail information of the CAM amp cards inserted in the slots You can check all this information according to the help message at the bottom of each menu Note All information showed in this menu and submenu is abstract from CAM amp card In case something is wrong it may be the problem of CAM or card When you insert the CAM correctly at any time a message will show in the screen to tell you that which CAM has been detected by the receiver and is available now 15 Menu USB If you enter to the USB Menu you will see the picture like the below Note If no USB Hard Disk inser
40. to move highlight and press OK key to play the highlighted channel 7 Press P P key to page up and page down 8 Press EXIT key to exit the channel list 9 15 Sleep 1 This function can set sleep timer When you set a sleep timer and the time arrive the system will 5 Press YELLOW key to open Timer window enter to standby automatically User can save a timer as he want More about 2 Press K isien key to switch the mode timers You can read in between Sleep Timer Off 10 30 60 90 120 6 Press REC key to directly add timer for minutes recording event 9 16 Page Up Page Down 7 In EPG menu press EXIT to close EPG screen 1 In Channel list press P P key can page up and 9 13 TV RADIO page down the channel list In TV mode pressing COA tv ravio key can 9 17 TEXT switch to Radio mode In Radio mode press 1 A crv ravio key to switch to TV mode 1 Press TEXT key in full screen you can open teletext page on the channel which has teletext 9 14 Channel List information 1 In full screen press OK key to enter Channel List ry TV Ust 7 Gres Aa So 0151 ESP HD Catch 0192 ESP MO Russian 0169 SESP HD Turk 0165 TVS 01 2n4190 HOTRRO 13k 1 1f the channel has no teletext information it will show No Teletext Data on the screen 2 Press RED key to change channels group 3 Press BLUE key to open the Sort window There are five kinds of sorting
41. udio language as default If the channel hasn t the suited audio language then the system will second audio compare automatically with language 18 User manual 3 Second Audio If the channel has no correspond audio with First Audio but have corresponded audio with Second Audio system will play the second audio language as default If no audio language corresponds with the Second Audio then the default language of current channel will be played automatically The selections of audio languages include English French German Russian Arabic Portuguese Turkish Spanish Polish and Italian 4 Audio Priority You can select the Audio Priority among Dolby and Language If Dolby mode is selected AC3 audio track will be played even if track language not correspond to selected one in above functions First and Second Audio 5 EPG Language Press lt gt keys to select EPG language 6 Subtitle Language It is an item for changing the language of the Subtitle As long as the services support it the Subtitle language is changeable by press vettow KEY on your RCU The supported language can be changed without any notice 7 Teletext Language Press lt gt keys to select TXT language As long as the services support it the Teletext language is changeable by press GREEN KEY ON your RCU The supported language can be changed without any notice 8 You can press EXIT
Download Pdf Manuals
Related Search