Electrical/Battery/Mechanical Protocols – Beauty Care
Contents
1. Turnaround time 7 working day Sample size 3 pieces Testing charge Sample size Basic charge USD 350 Additional charge DG EA051 US 80 USD exclude chemical test 12 pieces Chemical amp Energy Efficiency test for all Subject to actual sample Subject to actual sample electrical items to California DG EA065 US Remark Additional samples and tests may be necessary subjected to the review by Intertek upon receipt of the sample Technical information and related recommendations listed in this specification are proprietary information of Intertek Testing Services Copying is prohibited without permission of Intertek in written document This specification does not purport to include all the necessary provisions nor address all of the safety concerns if any associated with its use Compliance with this specification does not of itself confer immunity from legal obligations BV Lab Number Technician Name Test Date Reviewed By Date Page 1 of 6 DOLLAR GENERAL CORPORATION TEST PROTOCOL FOR DGEN 02045 US HAIR ACCESSORIES HAIR BOBBY PINS CLIPS ADULT V7 Evaluation Citation Method Noe Criteria VT Rating Samples SUPPLEMENTAL PROTOCOLS S O SUPPLEMENTAL PROTOCOLS The sample should be reviewed against the California Proposition 65 o A i requirements of California Proposition 65 to determine if additional testing or labeling is required LABELING Bas Time ee se2. Electrical rating Date Code Other markings required by standard The cautionary or warning marking intended to inform the user of a potential risk of fire electrical shock or injury to persons shall be provided 5 User Manual UL 859 Cls 62 66 Instructions and warnings shall be provided in the user manual Important Safety identifying reasonable foreseeable uses or misuses of the Instructions product It shall also include instructions regarding the Assembly Instructions installation use safety and maintenance All accessories shall be described in the user s manual and provided with instructions for proper use 6 Parts Inventory Shall meet label claims 7 FCC Part 15 rules Document Check FCC part 15 report shall be provided for verification if the operating frequency gt 9kHz for AC or operating frequency gt 1 705MHz for Battery operated product 8 FCC Part 15 marking Visual Marking shall include and instruction This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Instruction manual shall include Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE Th
3. Temperature Teston UL 1028 Cls 37 Under normal operating conditions handle grasped for lifting or Accessible Parts holding and other accessible surfaces shall not attain excessive temperature as follows Outer surface 257 F 125 C 21 Drop Test for Hand In house method Functional shall operate as intended after the unit is dropped Held Unit from 3 feet onto a hard wooden surface 3 times Fitness for Use DAW 4 Ell lw VU BU 22 Functional Check Actual Use All the major features shall be matched with the installation and use instructions and claims made on the packaging with no inaccurate or misleading statements about the product or any other user friendliness problems 23 Ease of Installation Follow directions for Report relative ease of installation Report if instructions installation in Instruction pertaining to installation are complete and understandable manual Parts shall be provided as claimed 24 Ease of Cleaning Follow Instructions or Follow the cleaning instruction Removable parts shall be Wipe Gently with Damp replaced easily and not causing any safety hazards Cloth d sod e 25 With Child Appealing DG EA051 Shall meet the requirements in DG EA051 Features 26 Chemical amp Energy DG EA065 Shall meet the requirements in DG EA065 Efficiency test for all e All products containing CA Prop 65 warning label will be electrical items to reported as FAILED California 27 Dollar General Client require
4. NA Not Applicable NT Not Tested Rating Key Incomplete INCOMPLETE PPT Rating Only Complete PPT COMPLETE Rating Only GOOD Good UNSAT Unsatisfactory No Of Samples Required for Complete Testing oo Client Approval OCTOBER 24 2012 No Of Fully Packed Cartons For Transit Testing Creation Dat Pees 2010 A reation Date No Of Working Days For Complete Testing Last Revision Date OCTOBER 30 2012 Pricing Review Date Technical Review Date
5. horizontal softwood surface covered with two layers of white tissue paper and operated until constant temperatures are attained During this test both the heating element and the blower are to be operating The position of the dryer is to be such considering the possibilities of actual service that the maximum temperature will be produced on the paper covered supporting surface The temperature rise on the paper shall not exceed 125 C 225 F Technical information and related recommendations listed in this specification are proprietary information of Intertek Testing Services Copying is prohibited without permission of Intertek in written document This specification does not purport to include all the necessary provisions nor address all of the safety concerns if any associated with its use Compliance with this specification does not of itself confer immunity from legal obligations Product Spec DG EA069 US Hair d Intertek vaision d Date August 10 2011 Page 3 of 3 Test requirements Reference Method 23 Drop Test for Hand In house method Functional shall operate as intended after the unit is dropped Held Unit from 3 feet onto a hard wooden surface 3 times Fitness for Use a eae a ee eel 24 Functional Check Actual Use All the major features shall be matched with the installation and use instructions and claims made on the packaging with no inaccurate or misleading statements about the product or any o
6. tests MTHD Actual use Materials used features tested consumables method etc Must withstand 4 2 in 1 with no failure Modification 4 2 in lb and expanded scope to other products Durability claspin CPSD HL 01058 Adequate for use no failure after repeated use y ping MTHD Actual use 100 times cycling open close Torque test for removal of ASTM F963 07 section components 8 8 modified BV Lab Number Technician Name Test Date Reviewed By Date Page 5 of 6 DGEN 02045 US HAIR ACCESSORIES HAIR BOBBY PINS CLIPS ADULT V7 Samples Tension Test For Removal of ASTM F963 07 section Must withstand 15 lbf for 10 s with no failure ee kee ed re COLORFASTNESS DRY Colorfastness to crocking AATCC 8 1 Class 4 0 Miniimum WET Colorfastness to crocking AATCC 8 1 Class 3 0 Minimum DRY Colorfastness to rotary crocking AATCC 116 1 Class 4 0 Minimum WET Colorfastness to rotary crocking AATCC 116 1 Class 3 0 Minimum All Colors Colorfastness to perspiration AATCC 15 07 1 Class 3 0 Minimum Colorfastness to water AATCC 107 1 Textile Class 4 0 minimum Remark PPR Pre Production Review VT Verification Test Key 5 Additional Charge For This Test a Mandatory Requirement By Request Only Result Key C Claimed R Recorded BV Lab Number Technician Name Test Date Reviewed By Date Page 6 of 6 M Meets NM Does Not Meet
7. to California DG EA065 US Subject to actual sample Subject to actual sample Remark Additional samples and tests may be necessary subjected to the review by Intertek upon receipt of the sample Technical information and related recommendations listed in this specification are proprietary information of Intertek Testing Services Copying is prohibited without permission of Intertek in written document This specification does not purport to include all the necessary provisions nor address all of the safety concerns if any associated with its use Compliance with this specification does not of itself confer immunity from legal obligations Product Spec DG EA069 US Hair dryer Intertek Version 2 Date August 10 2011 Page 1 of 3 Test requirements Reference Method Document Review E EEEEE s 1 Labelling Packaging Uniform Labelling Distributors Name amp Address City State amp Zip or product Regulation 2 Country of origin NAFTA amp FTCA Sect 5 Country Of Origin If Imported marking If imported Mark directory with the sample s listing number and model number 4 General amp Cautionary UL 859 Cls 60 61 The following markings shall be legible and readily visible during Markings use Manufacturer s name trademark or etc Model number type reference or etc
8. 2 Accessibility of Live UL 1028 Cls 10 An opening in an enclosure shall have a minor dimension less Parts than 1 in 25 4 mm and such a part or wire shall not be contacted by the probe illustrated in Figure 10 1 13 Power Cord UL 1028 Cls 13 1 1 9 amp The length of a flexible cord for an appliance configuration 13 1 1 10 shown in Figure 13 2 shall be as specified in Table 13 2 The flexible cord for an appliance configuration shown in Figure 13 2 shall be of a Type as specified in Table 13 2 or shall have properties such that it is at least equally as serviceable for the application 14 Plug UL 1028 Plug shall be 3 wire grounding type or 2 wire polarized attachment plug D ee en ae ee Electrical Safety 15 Component Check Visual If listing safety report provided report any difference of component used in the sample and the listing report Exclude plastic material insulation material or other components without marking 16 Dielectric Strength UL 1028 Cls 39 Appliance heated to its operating temperature and is subjected Test for 1 min to a 60 hertz essentially sinusoidal potential applied between live parts and exposed dead metal parts There shall not be dielectric breakdown Technical information and related recommendations listed in this specification are proprietary information of Intertek Testing Services Copying is prohibited without permission of Intertek in written document This specification does not purport
9. 5 milliampere for a grounded three wire portable appliance and c 0 75 milliampere for a grounded three wire stationary or fixed appliance 18 Power Input Test UL 859 Cls 36 The power input to an appliance shall comply with cls 36 3 and shall be within the inclusive range of 90 110 percent of that rating 19 Strain Relief UL 859 Cls 41 A pull force of 35lbf 155N is to apply to the cord with the conductor terminals disconnected for 1 minute No observable displacement or damage of the cord 20 Temperature Test on UL 859 Cls 37 3 Under normal operating conditions handle grasped for lifting or Accessible Parts holding and other accessible surfaces shall not attain excessive temperature as follows Surface supporting a cord connected appliance 29K Any point exposed to casual contact 60K Functional shall operate as intended after the unit is dropped Held Unit o u 3 feet onto a hard wooden surface e Or Suace Ste times Fitness for Use 22 Functional Check w Use All the ee features shall be matched with the installation and use instructions and claims made on the packaging with no inaccurate or misleading statements about the product or any other user friendliness problems 23 Ease of Installation Follow directions for Report relative ease of installation Report if instructions installation in Instruction pertaining to installation are complete and understandable manual Parts shall be provided as claimed 24
10. Ease of Cleaning Follow Instructions or Follow the cleaning instruction Removable parts shall be Wipe Gently with Damp replaced easily and not causing any safety hazards Cloth gest INIT EF EE WE iN FF E ATE _ AC Or 25 With Child Appealing DG EA051 Shall meet the requirements in DG EA051 Features 26 Chemical amp Energy DG EA065 Shall meet the requirements in DG EA065 Efficiency test for all e All products containing CA Prop 65 warning label will be electrical items to reported as FAILED California 27 Dollar General Client requirement Shall provide signed chopped document Dollar General Toxics Certificate of in Packaging Certificate of Compliance Compliance Toxics in packaging Client requirement 28 Volatile organic GC MS screening US Product with solvent based liquid eg Adhesive paints glues Substances VOC if EPA method 5000 and and etc shall not contain toxic aromatic compounds and hazard applicable 8021B doc review substances GC MS screening or US EPA method 5000 and 8021B In lieu of testing test report can be submitted if dated within 1 year Additional Charge Item Technical information and related recommendations listed in this specification are proprietary information of Intertek Testing Services Copying is prohibited without permission of Intertek in written document This specification does not purport to include all the necessary provisions nor address all of the safety c
11. Electrical Battery Mechanical Protocols Beauty Care Click on BLUE to go directly to page 043 Personal Grooming Appliance Rev 08 15 2011 044 Hair Cutter Rev 08 15 2011 0 ceeeeeeerees 069 Hair Dryer Rev O8 15 2011 ssccisssssscassassnceacsencians 2045 Hair Accessories Rev 11 16 2012 0 0 Product Spec DG EA043 US Personal Grooming Appliance Intertek Version 8 Date August 10 2011 Page 1 of 3 Product includes Hair Dryer Curling Iron and similar appliances Document Review EE SE ene 1 Labelling Packaging Uniform Labelling Distributor s Name amp Address City State amp Zip or product Regulation Product Identification 2 Country of origin NAFTA amp FTCA Sect 5 Country Of Origin If Imported marking If imported Mark directory with the sample s listing number and model number 4 General Markings UL 859 Cls 61 The following markings shall be legible and readily visible during use Manufacturer s name trademark or etc Model number type reference or etc Electrical rating Date Code Other markings required by standard 5 Cautionary Markings UL 859 Cls 61 The cautionary or warning marking intended to inform the user of a potential risk of fire electrical shock or injury to persons shall be provided 6 User Manual UL 859 Cls 62 66 Instructions and warnings shall be provided in the user manual Important Safety identifying reasonable foreseeable uses or mi
12. PINS CLIPS ADULT V7 Evaluation Citation Method Ni Criteria VT Rating Samples FLAMMABILITY Shall not exceed the maximum allowable limit of no 7 16 CFR 1500 3 c 6 greater than 0 1 inches per second Flammability of solids vi 16 CFR 1500 44 j If warning statement about flammability is presented on the package provide exhibit photo in report PHYSICAL CHARACTERISTICS CPSD HL 01056 Report overall dimensions shall meet label claims If Dimensions MTHD Standard 1 applicable 0 5 measure CPSD HL 01056 Report overall weight shall meet label claims If Weight average total MTHD Standard 1 applicable 0 5 measure CPSD HL 01057 Report overall number of pieces shall meet label Number of Pieces MTHD Visual 1 claims If applicable 0 5 Parts Inventor CPSD HL 01057 1 Shall meet label claims 7 y MTHD Visual WORKMANSHIP Defects CPSD HL 01057 All Shall have no components missing malformed and MTHD Visual or fractured Shall have no discernible surface degradation CPSD HL 01057 including crazing shivering denting bubbles cracks 1 2 1 al za FPO x Defects stains deformations chips fractures heavy lines MTHD Visual nps OUR waves shear marks scratches scuff marks indentations or blisters PERFORMANCE Shall function as intended as received Actual use functionality not CPSD HL 01058 Report details of evaluation covered by other
13. all current carrying parts when the hand supported unit is immersed in water Electrical Safety ee er ee ene 15 Component Check Visual If listing safety report provided report any difference of component used in the sample and the listing report Exclude plastic material insulation material or other components without marking Technical information and related recommendations listed in this specification are proprietary information of Intertek Testing Services Copying is prohibited without permission of Intertek in written document This specification does not purport to include all the necessary provisions nor address all of the safety concerns if any associated with its use Compliance with this specification does not of itself confer immunity from legal obligations Product Spec DG EA043 US Personal Grooming Appliance Intertek Version 8 Date August 10 2011 Page 2 of 3 16 Dielectric Strength UL 859 Cls 38 Appliance heated to its operating temperature and is subjected Test for 1 min to a 60 hertz essentially sinusoidal potential 1000V applied between live parts and exposed dead metal parts There shall not be dielectric breakdown 17 Leakage Current Test UL 859 Cls 31 The leakage current of a cord connected portable stationary or fixed appliance when tested in accordance with 31 3 31 7 shall be no more than a 0 5 milliampere for an ungrounded two wire portable stationary or fixed appliance b 0
14. g Client requirement BV Lab Number Technician Name Test Date Reviewed By Date Page 2 of 6 DGEN 02045 US HAIR ACCESSORIES HAIR BOBBY PINS CLIPS ADULT V7 Samples ANALYTICAL S O O ANALYTICAL Qualitative Finished products only PD CR 12471 2002 Skin contact Nickel spot test CPSD AN 00013 MTHD i F Skin contact metal components negative test results NOTE Only if claimed nickel free 94 27 EC 2004 96 EC IQPTIQNAL TE By Request Only Nickel rel EN 1811 EN 12472 O t only and f ts onih ickel release CPSD AN 00014 n request only and for components only MTHD Cannot exceed 0 5 micrograms cm 2 per week OPTIONAL TEST By Request Only Applicable components with potential skin contact 2002 6 1 EC 2004 2 1 EC CPSD AN 00015 MTHD CPSD AN 00016 MTHDC CPSD AN 00017 MTHD AZO Colorants GC MS Max 3 colors tested once if positive EA will be tested separately and EA color charged separately BV Lab Number Technician Name Test Date Reviewed By Date Page 3 of 6 DGEN 02045 US HAIR ACCESSORIES HAIR BOBBY PINS CLIPS ADULT V7 Evaluation Citation Method Ni Criteria Rating Samples All accessible surface coatings before and after use and abuse testing on toys intended for children up to age 14 child care articles children s food contact items all jewelries including jewelry making craft kits sha
15. is equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Technical information and related recommendations listed in this specification are proprietary information of Intertek Testing Services Copying is prohibited without permission of Intertek in written document This specification does not purport to include all the necessary provisions nor address all of the safety concerns if any associated with its use Compliance with this specification does n
16. ll comply with the following limits Antimony Sb 60 mg kg Arsenic As 25 mg kg Barium Ba 1000 mg kg Cadmium Cd 75 mg kg Chromium Cr 60 mg kg Lead Pb 40 mg kg Mercury Hg 60 mg kg Selenium Se 500 mg kg Report actual results or include data table within report Note Children s food contact items mean food contact CPSD AN 00003 articles intended for children up to 14 years of age Soluble heavy metal contents in MTHD CPSD AN For coating on toys intended for children up to age surface coatings 00164 MTHD 14 soluble heavy metal testing is conduct directly Report of ASTM F963 will be issued with note in report Soluble lead Pb requirement is reduced to 40ppm as per client requirement For coating on products other than toys screening of 8 total heavy metals is conduct first and no compositing is allowed If any of the above heavy metal s is are detected exceed the require limit soluble heavy metal testing will be proceed For soluble heavy metal testing test method and reporting rules e g application of correction factor from ASTM F963 08 section 4 3 5 2 and 8 3 are applied Excluding Ride on bicycle wheels tubes and tires stroller wheels tubes and tires writing instrument nibs car seat buckles keyed locks and keys Client requirement BV Lab Number Technician Name Test Date Reviewed By Date Page 4 of 6 DGEN 02045 US HAIR ACCESSORIES HAIR BOBBY
17. me a _ i F P and L Act 16 CFR A a 2 a A a s Name amp ackaging and Labeling Act or a 500 OR NIST Uniform ress City State ip other products Laws and Regulations Uniform Packaging and Labeling Han o 130 Regulations Net quantity of contents shall be expressed in terms of F P and L Act 16 CFR weight or mass measure numerical count or 500 OR NIST Uniform combination so as to give accurate information to Laws and Regulations facilitate consumer comparison U S and metric Handbook 130 units One Time Use Products Fair Packaging and Labeling Act or all other products Uniform Packaging and Labeling Regulations aS n gal EP edL Ac OBER a cite 8 500 OR NIST Uniform other products Laws and Regulations Uniform Packaging and Labeling Handbook 130 Regulations Shall indicate country of origin legibly permanently and in comparable size and close proximity to any si mention of country other than country in which the Panay Qf Origm O E A article was manufactured or produced Must be visible at point of purchase CPSD HL 01057 Use care instructions that are clear and Use labeling MTHD Visual 1 understandable shall be provided in language appropriate to destination countries if applicable Shall provide signed chopped document Dollar CPSD GB 00001 General Toxics in Packaging Certificate of MTHD Client Compliance requirement Dollar General Certificate of Compliance Toxics in packagin
18. ment Shall provide signed chopped document Dollar General Toxics Certificate of in Packaging Certificate of Compliance Compliance Toxics in packaging Client requirement 28 Volatile organic GC MS screening US Product with solvent based liquid eg Adhesive paints glues Substances VOC if EPA method 5000 and and etc shall not contain toxic aromatic compounds and hazard applicable 8021B doc review substances GC MS screening or US EPA method 5000 and 8021B In lieu of testing test report can be submitted if dated within 1 year Additional Charge Item Technical information and related recommendations listed in this specification are proprietary information of Intertek Testing Services Copying is prohibited without permission of Intertek in written document This specification does not purport to include all the necessary provisions nor address all of the safety concerns if any associated with its use Compliance with this specification does not of itself confer immunity from legal obligations Intertek Product Spec DG EA044 US Hair Cutter Version 7 Date August 10 2011 Page 3 of 3 Testing Charge amp Sample Size amp Turnaround Time Turnaround time 7 working day Sample size 3 pieces Testing charge Sample size Basic charge USD 250 Additional charge DG EA051 US 80 USD exclude chemical test 12 pieces Chemical amp Energy Efficiency test for all electrical items
19. niform Labelling Distributors Name amp Address City State amp Zip or product Regulation Product Identification 2 Country of origin NAFTA amp FTCA Sect 5 Country Of Origin If Imported marking If imported Mark directory with the sample s listing number and model number 4 General Markings UL 1028 Cls 54 1 54 2 amp The following markings shall be legible and readily visible during 54 6 use Manufacturer s name trademark or etc Model number type reference or etc Electrical rating Date Code Other markings required by standard 5 Cautionary Markings UL 1028 Cls 54 1 54 2 amp The cautionary or warning marking intended to inform the user of 54 6 a potential risk of fire electrical shock or injury to persons shall be provided 6 User Manual UL 1028 Cls 55 61 Instructions and warnings shall be provided in the user manual Important Safety identifying reasonable foreseeable uses or misuses of the Instructions product It shall also include instructions regarding the Assembly Instructions installation use safety and maintenance All accessories shall be described in the user s manual and provided with instructions for proper use ConstructionCheck ft 9 Workmanship Visual Shall have no major defects such as iar ae Cracks or breakage on provided accessories Serious scratches on the external surface Peeling of rating or caution warning label turning points edges or moving parts 1
20. oncerns if any associated with its use Compliance with this specification does not of itself confer immunity from legal obligations Intertek Product Spec DG EA043 US Personal Grooming Appliance Version 8 Date August 10 2011 Page 3 of 3 Testing Charge amp Sample Size amp Turnaround Time Turnaround time 7 working day Sample size 3 pieces Testing charge Sample size Basic charge USD 250 Additional charge DG EA051 US 80 USD exclude chemical test 12 pieces Chemical amp Energy Efficiency test for all electrical items to California DG EA065 US Subject to actual sample Subject to actual sample Remark Additional samples and tests may be necessary subjected to the review by Intertek upon receipt of the sample Technical information and related recommendations listed in this specification are proprietary information of Intertek Testing Services Copying is prohibited without permission of Intertek in written document This specification does not purport to include all the necessary provisions nor address all of the safety concerns if any associated with its use Compliance with this specification does not of itself confer immunity from legal obligations Product Spec DG EA044 US Hair Cutter Intertek Version 7 Date August 10 2011 Page 1 of 3 Test requirements Reference Method Requirement Document Review ft 1 Labelling Packaging U
21. ot of itself confer immunity from legal obligations Product Spec DG EA069 US Hair d Intertek vaision d Date August 10 2011 Page 2 of 3 Test requirements Reference Method ConstructionCheck i O SO 9 Packing No hazard when removing the packing 10 Workmanship Visual Shall have no major defects such as Cracks or breakage on provided accessories Serious scratches on the external surface Peeling of rating or caution warning label turning points edges or moving parts 13 Accessibility of Live UL 859 Cls 6 5 3 The enclosure of an appliance shall have no opening that Parts permits a probe as illustrated in Figure 6 1 to touch any part that involves a risk of electric shock 14 Power Cord UL 859 Cls 11 3 1 1 amp An appliance shall be provided with a length of flexible cord in 11 3 1 6 accordance with Table 11 1 and an attachment plug for connection to the supply circuit The flexible cord shall be of a type indicated in Table 11 2 or the equivalent Plug shall be 3 wire grounding type or 2 wire polarized attachment plug Electrical Safety SSS SS Sa eee 16 Component Check Visual If listing safety report provided report any difference of component used in the sample and the listing report Exclude plastic material insulation material or other components without marking 17 Dielectric Strength UL 859 Cls 38 Appliance heated to its operating temperature and is subjected Test for 1 min to a 60 he
22. rtz essentially sinusoidal potential 1000V applied between live parts and exposed dead metal parts There shall not be dielectric breakdown 18 Leakage Current Test UL 859 Cls 31 The leakage current of a cord connected portable stationary or fixed appliance when tested in accordance with 31 3 31 7 shall be no more than a 0 5 milliampere for an ungrounded two wire portable stationary or fixed appliance b 0 5 milliampere for a grounded three wire portable appliance and c 0 75 milliampere for a grounded three wire stationary or fixed appliance 19 Power Input Test UL 859 Cls 36 The power input to an appliance shall comply with Cls 36 3 and shall be within the inclusive range of 90 110 percent of that rating 20 Strain Relief Test UL 859 Cls 41 The strain relief device withstands a 35 lb 156 N pull force 20 Ib 89 N force for appliances weighing 0 5 Ib 0 23 kg or less without cord applied for one 1 minute in any direction without transmitting the pull to terminals splices or internal wiring 21 Temperature Test on UL 859 Cls 37 5 Under normal operating conditions handle grasped for lifting or Accessible Parts holding and other accessible surfaces shall not attain excessive temperature as follows Handle 90 F 50 Switches 108F 60 Enclosure when measured 0 5 in 12 7 mm from outlet 126 F 70 22 Abnormal Test UL 859 Cls 39 3 1 A hand supported hair dryer is to be placed on a flat
23. suses of the Instructions product It shall also include instructions regarding the Assembly Instructions installation use safety and maintenance All accessories shall be described in the user s manual and provided with instructions for proper use ConstructionCheck ft 9 Workmanship Visual Shall have no major defects such as Cracks or breakage on provided accessories Serious scratches on the external surface Peeling of rating or caution warning label 0 Mechanical Assembly Visual Check All mechanical parts shall be securely fixed and prevented from turning 7 11 Internal Wiring Visual Check Wireways shall not allow wires to come in contact with sharp points edges or moving parts 12 Accessibility of Live UL 859 Cls 6 5 3 The enclosure of an appliance shall have no opening that Parts permits a probe as illustrated in Figure 6 1 to touch any part that involves a risk of electric shock 13 Power Cord UL 859 CLs 11 3 1 1 amp An appliance shall be provided with a length of flexible cord in 11 3 1 6 accordance with Table 11 1 and an attachment plug for connection to the supply circuit The flexible cord shall be of a type indicated in Table 11 2 or the equivalent 14 Plug Visual Check Plug shall be 3 wire grounding type or 2 wire polarized attachment plug For hair dryer The product shall incorporate one of the following a GFCI b IDCI c Integral protective device of another type that de energizes
24. ther user friendliness problems 25 Ease of Installation Actual use Report relative ease of installation Report if instructions 26 i pertaining to installation are complete and understandable Parts shall be provided as claimed 27 Ease of Cleaning Follow the cleaning instruction Removable parts shall be replaced easily and not causing any safety hazards 28 Durability of Switches Switches shall continue to function correctly after 200 cycles of operations _Additional Test T 29 With Child Appealing DG EA051 Shall meet the requirements in DG EA051 Features 30 Chemical amp Energy DG EA065 Shall meet the requirements in DG EA065 Efficiency test for all e All products containing CA Prop 65 warning label will be electrical items to reported as FAILED California 31 Dollar General Client requirement Shall provide signed chopped document Dollar General Toxics Certificate of in Packaging Certificate of Compliance Compliance Toxics in packaging Client requirement 32 Volatile organic GC MS screening US Product with solvent based liquid eg Adhesive paints glues Substances VOC if EPA method 5000 and and etc shall not contain toxic aromatic compounds and hazard applicable 8021B doc review substances GC MS screening or US EPA method 5000 and 8021B In lieu of testing test report can be submitted if dated within 1 year Additional Charge Item Testing Charge amp Sample Size amp Turnaround Time
25. to include all the necessary provisions nor address all of the safety concerns if any associated with its use Compliance with this specification does not of itself confer immunity from legal obligations Product Spec DG EA044 US Hair Cutter Intertek Version 7 Date August 10 2011 Page 2 of 3 Test requirements Reference Method 17 Leakage Current Test UL 1028 Cls 32 The leakage current of a cord connected portable stationary or fixed appliance when tested in accordance with 31 3 31 7 shall be no more than a 0 5 milliampere for an ungrounded two wire portable stationary or fixed appliance b 0 5 milliampere for a grounded three wire portable appliance and c 0 75 milliampere for a grounded three wire stationary or fixed appliance Power Input Test UL 1028 Cls 36 3 The current or wattage input to an appliance shall not be more than 110 percent of the rated value when the appliance is operated under the condition of maximum normal load as described in standard Strain Relief Test UL 1028 Cls 46 The strain relief means provided on an attached flexible cord shall withstand for 1 min without displacement a direct pull of 35 lbf 156 N applied to the cord with the connections within the appliance disconnected The strain relief is not acceptable if at the point of disconnection of the conductors there is such movement of the cord as to indicate that stress would have resulted on the connections
Download Pdf Manuals
Related Search