Open - Lobeco
Contents
1. Networ Using the Quick Arm optional The Quick Arm feature may be used if it is enabled Quick Arm will allow the user to arm the security system in the AWAY mode by pressing the EXIT key or arm in the STAY mode by pressing the STAY key This feature is used for ARMING ONLY and will not disarm the security system This is ideal for maid or baby sitter code etc Changing modes while system armed Pressing the STAY key will turn on off toggle a delay on entry exit doors and turn on off toggle the instant icon Optional Press the BYPASS key at this time to turn on off toggle all designated interior zones Optional When armed pressing the EXIT key will start the exit delay enabling you to leave the building IMPORTANT The instant icon needs to be off at this time if you plan on re entering the building otherwise you will create an alarm You restore an entry delay by pressing the STAY key again Disarming the system When you enter the protected area through one of the designated Entry Exit doors the keypad control will sound a continuous tone for the duration of the entry delay time or until you enter a valid code The armed icon will go off and the tone will stop The security system is now DISARMED If a valid code is not entered before the end of the entry delay an alarm will occur NOTE If the armed icon is flashing during the entry delay the alarm system has been activated in your a2. ccsscssossossossossossossossonsonsonsonsonsonsousonsousonsonsonsousonsonsonsonsonsonscusonsonsonsonsonsonsonsonsensonsonsons 17 NX 1348E ICON User manual Page 3 23 07 05 Networ INTRODUCTION This manual is furnished to help you understand your security system and become proficient in its operation All users of your security system should read and follow the instructions in this booklet and if possible practice on the keypad control while your professional installer is on site Failure to do so could result in the security system not working properly Please keep this booklet in an accessible location for the life of the security system If you do not understand any part of this manual you should notify your installing company The SECURITY CONTROL can be turned on ARMED and off DISARMED by entering a 4 or 6 digit code into the Keypad Control which is similar to a telephone keypad If your Security Control has been so programmed you may be able to turn on ARM your System by simply pressing the STAY or EXIT key The system must always be disarmed using a 4 or 6 digit code The LED keypad includes up to 61 icons and a built in electronic sounder These provide specific information relating to the status of the security system which is described in the booklet Understanding what the icons and sounds mean will help you easily operate your system Keep in mind the level of security you will obtain with this system relates specifical
3. COPYRIGHT 2005 GE Security EMEA bvba All rights reserved GE Security EMEA bvba grants the right to reprint this manual for internal use only GE Security EMEA bvba reserves the right to change information without notice
4. LOSS OF SYSTEM TIME This icon will illuminate when there has been a loss of power and your system clock needs to be reset SEE NOTE AT END OF TABLE EXIT Press the key to exit the Service Menu NOTE to Icons 6 7 8 This fault is global in nature and will affect all partitions of a multi partition system NX 1348E ICON User manual Page 16 23 07 05 Networ KEYPAD CONTROL TONES BEEPS A sounder is built into the keypad If programmed your system keypad may sound for any of the following reasons Beeps for all keypresses Sounds a continuous tone during the Entry delay time Pulses when a day zone is violated while the system is disarmed Pulses when a FIRE zone has a trouble condition Beeps 3 times for trying to arm with the Not Ready icon off if Force Arming has not been selected Beeps for 1 second or emits a ding dong sound for the Chime feature Beeps during an exit delay beeps rapidly for the last 10 seconds of an exit delay and beeps 1 second at the end of the exit delay when the armed status changes and the AC power is off when the armed status changes and any zonels are bypassed Pulses when the armed status changes and a low battery is detected Pulses when the armed status changes and Tamper condition is detected Beeps to indicate Telephone Line Cut if selected Pulses when one or more of the f
5. or enter new 4 or 6 digit user code While using the A and W keys you can change any digit by entering a new digit This will advance you to the next digit To delete a user code enter for a 4 digit code or for a 6 digit code Step 6 The ready led will flash indicating you are back at Step 2 above If the code is rejected the sounder will beep 3 times Step 7 If another user code needs be programmed return to Step 4 Step 8 Press the key while the ready led is flashing to exit the User Code Programming Mode NX 1348E ICON User manual Page 12 23 07 05 ASSIGNING USER CODE AUTHORITY LEVELS Assign authority levels to users by following the steps below Assign user codes before assigning authority levels Step 1 Press 6 Master Arm Disarm Code 4 Someone changing the authority of another person can only add or remove partition authorization for partitions to which they have access Step 2 The ready led will flash Step 3 Enter the 2 digit user number to be assigned authority The ready led is constant and the instant icon will flash Step 4 Icons illuminated indicate the authority levels assigned to this code An explanation of the icons is listed in the following table You may toggle turn on off the authority level by pressing the number for that authority level ICON AUTH
6. Networx Series NX 1348E ICON Icon keypad User manual imagination at work Networ 7 TABLE OF CONTENTS aro tin voe niece onn ende IE 3 2555 4 GLOSSARY 5 202 2506 zeerste 5 EMERGENCY ACTIVATION 5 22 6 ICON KEYPAD DISPLAY amp LED S escrita rere 7 2 Le eee eee e ve cect studs 7 J niet 9 KEYPAD FUNCTION Sin i 10 ARMING YOUR SYSTEM IN THE AWAY MODE uueesscessssscssccsscssessecsscsscssssssessecsscsscsscssssssseseessesscsssssucsusssesssessssecsucsscsasssussesssssessscssessessesasssvssecssestessessees 10 ARMING YOUR SYSTEMIN THES STAY MODE tele te eee 10 USING THE QUICK ARM OPTIONAL 11 CHANGING MODES WHILE SYSTEM ARMED wucescssccsssssssssessessessccssesssessessessscsscss
7. ORITY LEVELS IF ICON 8 IS OFF 1 Reserved Note Do not change if on 2 Arm Only 3 Arm Only After Closing Time 4 Master Arm Disarm can program other codes 5 Arm Disarm 6 Bypass Zones 7 Open Close Reporting 8 If this icon is on this code is programmed as a function code Do not change Press tt to exit Step 5 Press the key The ready led is on constant and instant icon is on constant This moves you to the partition enable The user has access in partitions that are illuminated Step6 Theilluminated numbers indicate each partition where the user has access To change any of the partitions where the user has access press numbers corresponding to areas where you want to give the user access or deny access Example If zone icon 2 is lit then the user is assigned access to partition 2 By pressing the 2 key the icon will go off denying access to partition 2 Refer to the following chart ICON PARTITIONS ASSIGNED 1 Partition 1 Partition 2 Partition 3 Partition 4 Partition 5 Partition 6 Partition 7 Partition 8 COIN OY Step 7 When the partitions are assigned press the key This returns you to Step 2 previously mentioned At this point you may enter another user number to assign authority level Repeat Steps 3 7 until you have assigned authority levels to all user numbers Step8 Press the key to exit the Assigning Authority Level Progra
8. alarm panel Central Station The location where alarm data is sent during an alarm report Chime Feature An option that allows the keypad to sound a ding dong whenever an entry exit door is opened Codes Can be either User Codes relating to a person or Function Codes a toggle switch to turn specific functions on off NOTE A system may have either four digit codes or six digit codes but not a mixture of the two Duress Code An option that allows a special code to be sent to the central station that indicates the alarm system is being operated under duress Forced Arming An option that allows the system to be turned on ARMED with one or more zones open A system that is ready to be force armed will flash the ready icon Note Those zones that are not ready will not create an alarm Function Code A Function Code is either a four 4 or six 6 digit code that has been programmed by the installer to operate a device Group Bypass An option that allows the user to bypass multiple zones with a single operation Instant Delay An option that allows an instant alarm condition for Entry Exit doors or grants a delay to allow someone to enter exit the building without an alarm or before entering a user code to disarm Master Code A master arm disarm code that can program other user codes Partitioned System A system divided into multiple areas in which its own user or
9. an be toggled on or off by pressing the Stay key while the system is armed When the instant icon is off the entry exit doorls is delayed NX 1348E ICON User manual Page 7 23 07 05 Networ 6 LISTEN IN ICON Listen in icon is on when an NX 534E audio module is active in listen in mode POWER ICON The power icon is on if the mains power is on It will be off if there is no mains The power icon will flash if the System has a low battery condition v READY ICON The ready icon is on when the system is ready to arm and flashes if ready to force arm A NOT READY ICON The not ready icon is on when the system is not ready to arm because of a zonels being faulted E ALARM ICON The alarm icon is flashing when an alarm has occurred 2 SILENCED ICON The silenced icon appears after a code has been entered to silence the siren but the zone has not been cleared TAMPER ICON The tamper icon is on when zone s is tampered Press k 2 and refer to the Service Menu section of this manual for further instructions 2 gt lt SERVICE ICON The service icon is on when a tamper occurs or when the system requires service Press 2 and refer to the Service Menu section of this manual for further instructions AN TROUBLE ICON The trouble icon is on when a dayzonels are faulted or when there is a trouble in the system ENTER CODE ICON The enter code icon is on whenever a valid code sho
10. are designated as group bypass zones will be bypassed Press the BYPASS key again or press the key to exit group bypassing Unbypassing zones To manually unbypass zones perform the bypassing procedure on a zone that is already bypassed The corresponding icon for that zone will go off when unbypassed NOTE All zones will automatically be unbypassed each time the system is disarmed Turning the door chime ON and OFF The door chime is turned on or off by pressing the CHIME key while the system is in the disarmed state If the chime is on the chime led will be illuminated If the chime is off the chime led will be off Each press of the CHIME key will toggle the chime feature on off and produce a momentary ding dong sound ADDING AND CHANGING USER CODES Your system must be Disarmed to change user codes Step 1 Press 5 Step 2 The Enter Code icon will display Enter a Master Arm Disarm Code For partitioned systems someone changing the code of another person must have access to all more partitions than the user being changed Step 3 Ready led will flash Step 4 Enter the 2 digit user number Always enter 2 digits such as 0 3 for user 3 Step 5 The instant icon will flash and zone icons will illuminate specifying the first digit of the user code gt When allicons are all illuminated code is blank when all icons are off gt Use the A and F keys to view the next digit
11. bsence Leave the building immediately and call your alarm company and or the police from a safe location CANCEL ABORT feature optional The cancel led will flash during an abort delay time If a code is entered followed by the CANCEL key while this led is flashing all abortable reports will stop the communication process Entering a code followed by the CANCEL key during or after an alarm report to the central station will cause the cancel led to come on It will stay on until the central station has received the cancel report Bypassing zones If you wish to bypass one or more zones this must be done while the system is in the disarmed state The following steps are used for bypassing zones Step1 Press the BYPASS key Step2 Enter user code if required optional The bypass led flashes Step 3 Enter 1 or 2 digits indicating the zone you wish to bypass i e press the 1 key for zone 1 press 11 21 for zone 12 Step4 Press the BYPASS key again Step5 corresponding zone icon will illuminate indicating the zone has been bypassed Repeat steps 3 and 4 for any other zone s that need to be bypassed Step 6 Press the BYPASS key again or press the st key to exit the Bypass Mode The bypass led will stop flashing upon exiting the Bypass Mode NX 1348E ICON User manual Page 11 23 07 05 Networ Group bypass By pressing the BYPASS key followed by the 0 key then the BYPASS key again all zones that
12. ch icon means in a service condition ICON PROBLEM 1 SYSTEM FAULT Press the 1 key The zone icon s that is illuminated corresponds to the system fault s below 1Over Current Fault 5Expander Low Battery 2Siren Trouble 6Expander Box Tamper 3Box Tamper 7Expander Trouble 4Expander Power 8Ground Fault Note Faults 1 amp 2 are global in nature and will affect all partitions of a multi partition system Press the key to return to the 1 of 8 service icons 2 RESERVED 3 ZONE LOW BATTERY Press the 3 key The zone icon s will illuminate showing which 2 5 has a low battery This only applies to wireless zones Press the key to return to the 1 of 8 service icons 4 ZONE LOSS OF SUPERVISION Press the 4 key and the zone icon s will illuminate showing which zonels has loss of supervision This only applies to wireless zones Press key to return to the 1 of 8 service icons 5 RESERVED 6 TELEPHONE LINE TROUBLE LINE CUT Press the 6 key The zone icon s will illuminate as they correspond to these service conditions 1 5 Reserved 6 Telephone Line Trouble Line Cut 7 Aux communication device failure The service icon will remain lit until the trouble clears and a user code is entered SEE NOTE AT END OF TABLE 7 FAILURE TO COMMUNICATE This icon will illuminate when there is a failure to communicate between your system and the central station SEE NOTE AT END OF TABLE 8
13. ch must be two 2 digits Note The clock is a 24 hour clock Refer to the following table Enter the minutes code which must be two 2 digits Then the ready icon will come on constant Example 7 minutes after would be entered 0 7 Hour Code Time Hour Code Time Hour Code 00 8 00 AM 08 4 00 PM 01 9 00 AM 09 5 00 PM 02 10 00 AM 10 6 00 PM 03 11 00 AM 11 7 00 PM 04 e 12 8 00 PM Noon 05 1 00 PM 13 9 00 PM 06 2 00 PM 14 10 00 PM 07 3 00 PM 15 11 00 PM Setting the keypad brightness Step 1 Step 2 Press 9 1 Press the A and W scroll keys to leden or darken the illumination behind the buttons and the ICON display It is usually easier to set this adjustment in a darkened room NX 1348E ICON User manual Page 15 23 07 05 Networ SERVICE MENU The service icon will be on if the security system requires service If the service icon is on press k 2 to determine the service condition If a zonels is tampered the tamper icon will flash and the zone will be on If a zonets is troubled the trouble icon will flash and the zone 5 will be on If the service icon is flashing one or more zone icon s will illuminate indicating what service s is required Press the A and W to scroll between tamper trouble and other service conditions Call your service provider immediately for these problems The following table provides a list of what ea
14. e protected site while reporting an alarm to the monitoring center Check with your installing company to determine how your security system will respond to the Panic Hold Up activation NX 1348E ICON User manual Page 6 23 07 05 Networ ICON KEYPAD DISPLAY amp LED s Ji e s 45 6 7T 8 9 10 fi 1213 14 15 D 21 22 25 25 25 2T 28 29 DN 35 36 MI 38 40 41 42 43 44 45 46 47 10 11 12 13 14 15 16 25 26 27 28 29 30 31 32 0 41 42 43 44 45 46 47 48 Arm or Disarm Cree your user coah Quick Arm aad Sayy Pross Stay bey To Guit Arm md Cet Pras Tet key 31 we va Door Chimei Press wre hey to etat Newel Smoke Desector Press x1 7 Company Understanding the icons a ARMED ICON The armed icon is on when the system is armed The armed icon is off when it is disarmed The armed icon will flash when there has been an alarm during the previous arm cucle d FIRE ICON A steady fire icon means a fire zone has been faulted A rapidly flashing fire icon means that a fire zone is in a trouble condition INSTANT ICON The instant icon is on when there is no delay on your entry exit door s Any time the instant icon is on and the exit delay has expired the opening of an entru exit door will produce an immediate alarm The instant icon c
15. ly with two major factors 1 The quantity quality and placement of security devices attached to this system 2 The knowledge you have of the security system and how that knowledge is utilized in a weekly test of the complete system You should be aware of the following facts when preparing a safety security plan for your home business Your security system is an electronic device and is subject to failure or malfunction Do not rely on it as your single source of security Your system should be tested weekly Your system will not work without power Warning devices will need to be loud enough wired correctly and properly placed to provide notification of an alarm event Smoke and heat detectors may not detect heat and smoke in all situations Use qualified security professionals to install and maintain your security system It may be possible to arm the security system without the backup battery connected Your periodic test should be done with AC Power removed to verify the battery is connected and adequately charged Care should be taken to plug in and restrain the AC Transformer after testing Please read the following information and instructions carefully before operating your security control system NX 1348E ICON User manual Page 4 23 07 05 Networ 7 Abort Delay GLOSSARY OF TERMS An option that allows a delay in reporting to the central station Authority Level The level of access an individual has when using an
16. m NX 1348E ICON User manual Page 13 23 07 05 Networ OTHER KEYPAD FUNCTIONS Setting the keypad tone Step 1 Press 0 Keypad is now in the Adjust Tone mode Step 2 Pressing the A key will make the keypad sounder to higher tones pressing the W key will make the keypad sounder go to lower tones Step 3 When the desired tone is reached press the key to set this tone and exit from the Adjust Tone mode Change partition optional Step 1 Press x 1 Step 2 Press a NUMBER key between 1 and 8 to change partitions momentarily Step 3 If no other key is pressed it will go back to its standard partition in ten seconds Step 4 If another key is pressed the system will remain in the new partition until no keys have been pressed for 60 seconds View alarm memory Step 1 Press 3 The zonels that created the last alarm will be displayed along with the alarm icon flashing on the keypad Step2 ALARM MEMORY feature will flash those zones that created alarms and will display steady those zones that were bypassed during the last alarm Test function optional If programmed this function will perform a battery test communicator test and or a siren test Alarms and reports will not be sent unless a communicator test is performed at which time a test signal will be sent Step1 Press 4 The test will be performed as programmed Step2 Ifthe siren test is performed enter a user c
17. ode to silence the siren Reset function This function is used to reset Smoke Detectors and Zone Troubles Your system must be Disarmed to use the Reset function Step 1 Press 7 Resets have now been performed Step2 Ifthe keypad begins beeping the reset did not execute properly Enter your code to silence the keypad Wait a few minutes and repeat step 2 to attempt another reset If the keypad still beeps after repeated attempts please contact your installer NX 1348E ICON User manual Page 14 23 07 05 Networ 7 Set system date Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Press 9 6 Enter Code icon will display Enter a Master Code The service icon will appear flashing Enter the Day of Week 1 Sunday 3 Tuesday 5 Thursday 7 Saturday 2 Monday 4 Wednesday 6 Friday Enter the Month Code Must always be two 2 digits 01 January 05 May 09 September 02 February 06 June 10 October 03 March 07 July 11 November 04 April 08 August 12 December Enter the Day Code Must always be two 2 digits Example 5th would be entered as 0 5 Enter the last two digits of the Year Code Example For 1997 enter 9 7 The ready icon will appear Setting the system clock Step 1 Step 2 Step 3 Step 4 Press 9 7 Enter Code icon will appear Enter a Master Code Then the service icon will begin to flash Enter the hour code whi
18. ollowing conditions are detected Zone or Box Tamper Low Battery AC Power Fail or Expander trouble Beeps 3 times once every minute for Sensor Zone Low Battery or Loss of Supervision Entering a code will silence the keypad for 12 hours Entering a valid code will silence the keypad sounder when it is pulsing The arm disarm state of your system will not change when entering a code to silence a pulsing keypad sounder Please contact your installer if a trouble condition exists NX 1348E ICON User manual Page 17 23 07 05 Networ SECURITY SYSTEM NOTES Installing Service Company For Service Call Central Station Duress Code This system isQ isnotQ partitioned EMERGENCY ACTIVATION KEYS check if enabled Fire Medical Emergency PROGRAMMED FUNCTIONS Police Abort Delay Cancel Alarm Forced Arming Auto Bypass Change Partitions Group Bypass Auto Instant Chime Quick Arm Battery Test Communicator Test Re Exit Siren Test ENTRY EXIT DELAY TIMES Exit Delay Time Secondary Exit Delay Time Entry Delay Time Secondary Entry Delay Time NX 1348E ICON User manual Page 18 23 07 05 ZONE DESCRIPTIONS 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 www gesecurity net EMEA Distribution is a division of GE Security EMEA bvba
19. ring or after an alarm report to the central station will cause the cancel led to come on It will stay on until the central station has received the cancel report Note The cancel feature must be enabled Page 9 23 07 05 Networ KEYPAD FUNCTIONS Arming your system in the AWAY mode AWAY is used when the user is away from the premise and wants the interior protected Step1 Close all protected doors and windows e Ready icon will be on or flashing when all protected zones and sensors are secure NOTE If any zones are bypassed a sensor in that zone can be violated without affecting the ready icon e The security system will not arm if the not ready icon is on or flashing e lf the power icon is off you have no AC power Restore power if possible If not contact your installing company Step 2 Enter your 4 or 6 digit user code to arm the system e The armed icon and exit led will illuminate e You may now leave the building NOTE The exit led will flash rapidly for the last 10 seconds of the exit delay as a warning to the user that the exit time is about to expire The user may wish to disarm and rearm the system if more time is needed Arming your system in the STAY mode STAY is used when the user is inside the premise and wants protection around the perimeter Step 1 Close all protected doors and windows e Ready icon must be on or flashing when all protected zones and sensors are secure NOTE If any zones are bypa
20. ssed a sensor in that zone can be violated without affecting the ready icon e The security system will not arm if the not ready icon is on or flashing e Ifthe power icon is off you have no AC power Restore power if possible If not contact your installing company for service Step2 e Enter your 4 or 6 digit user code e If Auto Bypass is enabled all interior zones will be bypassed if you do not leave through designated entru exit door If Auto Bypass is enabled omit Step 3 e When Auto Instant is enabled if you do not leave through a designated entry exit door the instant icon will illuminate indicating that the entry exit doors no longer have an entry delay If Auto Instant is enabled omit Step 4 Step3 e Press the STAY key e stay led will illuminate indicating that all interior zones are bypassed All interior devices will bypass automatically giving the user freedom of movement within the interior area bypass led will illuminate if any zone s are bypassed If any 20 6 have been bypassed previously by the user the icon s corresponding to the bypassed zonels will illuminate alerting the user that a zone s may be unprotected and can be faulted without an alarm Step4 e Totoggle from a delayed entry mode to an Instant mode press the STAY key again e instant icon will illuminate indicating that the entry exit doors have no entry delay NX 1348E ICON User manual Page 10 23 07 05
21. uld be entered on the keypad 1 48 ZONEICON The zone icons are off when everything is normal A zone icon will be on if the zone has been bypassed If a zone icon is flashing that zone is in alarm or has been faulted If a zone icon is flashing rapidly it means that the zone is in a trouble condition NX 1348E ICON User manual Page 8 23 07 05 Networ Understanding the LED s NX 1348E ICON User manual tt STAY LED The stay led is on when all interior motion detector zones are bypassed CHIME LED The chime led is on when the chime feature is on off otherwise EXIT LED The exit led is on during the exit delay Please note that the led will flash during the last 10 seconds of the exit delay as a warning that the time is running out The user may want to disarm the system if the exit led is flashing in order to prevent an alarm The user may then re arm the system and exit before the delay expires tit BYPASS LED The bypass led is on when any zone in this keypad s partition is bypassed The zonels that is bypassed will also be illuminated If the bypass led is off no zones are bypassed x CANCEL LED The cancel led will flash during an abort delay time If a code is entered followed by the CANCEL key while this led is flashing all abortable reports will stop the communication process Note The abort feature must be enabled Entering a code followed by the CANCEL key du
22. users control each area Perimeter The outer edge of the protected area Quick Arm An option that allows you to turn on ARM the security system by pressing either the STAY or EXIT key on the keypad control for ARMING only as programmed by the installing company User Code A four 4 or six 6 digit entry code used to arm or disarm the NX 1348E ICON User manual system Page 5 23 07 05 EMERGENCY ACTIVATION KEYS Fire Auxiliary Emergency Police NOTES You must hold these keys for 2 seconds to activate these functions Your system may not be programmed for these activation keys You should press these keys only in an emergency situation that requires response by emergency personnel If your system is programmed for these functions the following reports can be sent Fire Key This key can activate the fire alarm when pressed for two seconds If your system is connected to a monitoring center an emergency report could be sent to that center Auxiliary Emergency Key This key can activate the auxiliary alarm when pressed for two seconds If your system is connected to a monitoring center an emergency report could be sent to that center Police Panic Hold Up Key This key can sound a local audible alarm when pressed for two seconds If your system is connected to a monitoring center an emergency report could be transmitted to that center NOTE Some Panic Hold Up alarms are programmed to be silent at th
23. ussucsuesessssessussucsucsscsssssussssesscsscsacssussucsussssssessessucsucacssussecsusestessesscssessecsseess 11 PI SARMING THES YSTEMS E es eee e 11 CANCEL ABORT FEATURE OPTIONAL sssecsscccssseeccecsssesesscssssssescesssssececesssssesecesssssecsessssueccessesssesecussnssessesssuueccessssssesecsssnsessnseseecesssueesetsssuseseesssneess 11 BYPASSING ZONES hant A ALLE RM UON M RE USUS GIROWP eri Aas UNBYPASSING ZONES TURNING THE POOR CAME ON ANDRE e be tede eed 12 ADDING AND CHANGING USER 5 0 ep hn eoo ER a RE SERA 12 ASSIGNING 6 5 13 OTHER KEYPAD FUNCTIONS i Ito eir e o e 14 SETDWINGTEE KEYPAD TONE S z 14 CHANGE PARTITION OPTIONAL rette eee 14 VIEM ALARM MEMORY cede M csse ll re TERMI o ene TEST FUNCTION OPTIONAL RESET e LT Cc SET SYSTEM IDATE RU Iu SETTING THE SYSTEM CLOCK SENG THE KEYPAD BRIGHTNESS 15 SERVICE M 16 KEYPAD CONTROL TONES BEEPS
Download Pdf Manuals
Related Search