AJ-PCD30 - Panasonic
Contents
1. 3 0 cable B connector into the USB connector on the device then plug the other end A connector of the USB 3 0 cable into the USB 3 0 port on the personal computer Oco cen USB 3 0 connector Caution Even with a USB 3 0 cable if the device is connected to a USB 2 0 port it will operate as a USB 2 0 device lt Note gt No USB 3 0 cable is supplied with the device in the package Use a commercially available USB 3 0 cable shielded Take care to use a USB cable that is no longer than 3 metres The device may not operate properly with a cable longer than 3 metres To be connected by USB 2 0 Plug a USB 2 0 cable B connector into the USB connector on the device then plug the other end A connector of the USB 2 0 cable into the USB 2 0 port on the personal computer oco oeniev USB 3 0 Fl USB 3 0 connector lt Note gt No USB 2 0 cable is supplied with the device in the package Use a commercially available USB 2 0 cable shielded Take care to use a USB cable that is no longer than 3 metres The device may not operate properly with a cable longer than 3 metres 11 Installation continue 6 Verify that the personal computer recognises 12 the device lt Notes gt In Windows XP or Windows Vista some card slots of the device may be assigned drive names that have already been assigned to existing networks Reassign2. information EEE Y netmeli ine Uygundur EEE Complies with Directive of Turkey Pursuant to at the directive 2004 108 EC article 9 2 Panasonic Testing Centre Panasonic Service Europe a division of Panasonic Marketing Europe GmbH Winsbergring 15 22525 Hamburg F R Germany Table of Contents Read this first 05 2 P2 Driver a an nunna nunn 16 Before Use eee ee eeee 6 Installing a Windows P2 driver 16 Overview 000 eee eee eens 6 Installing a Macintosh P2 driver 16 Features s osha a oe ee ns 6 Uninstallation 16 Supplied Accessories Overview of dedicated software 17 AJ PCD30P AJ PCD30E Syke ee oe eee 7 Power management setting Operating Environment Windows Macintosh 17 Required for Installation 7 Installation 2 220 17 Parts and their Functions 8 Uninstallation 17 Front Panel e eee 8 Starting up and shutting down Rear Panel 000 8 the Power Management Setting Inserting a P2 Card 9 Software cec cee 17 Removing aP2 Card Pee ee ee 9 Power Management Setting Write protection of P2 Card 10 Software window 18 Power management function P2 Drive internal setting automatic switch off function 10 Windows 0 000 19 Installation 00000 10 P2 Drive internal setting DET RE
3. network drive names if your personal computer does not display all three card slots Use a USB cable with a flammability rating of VW 1 For the flammability rating check the printed part of the cover of the USB cable Recommended USB 3 0 cables based on information as of August 2011 Elecom U3C 10BK 1 0 m StarTech com USB3SAB3 0 91 m Recommended cables are listed on the Panasonic website http pro av panasonic net Installation continue Disconnect externally connected devices from your PC 1 Disconnect the USB connection as follows For Windows XP and Windows Vista Select Safe removal of hardware from the task tray and switch off Panasonic P2 Series USB Device For Windows 7 When a P2 card has been inserted into the device click the up arrow of the task tray and select Safely remove hardware and remove media Next select Remove Panasonic P2 Series USB Device if connecting with a USB 3 0 connector and Remove P2 drive if connecting with USB 2 0 connector If neither Panasonic P2 Series USB Device nor P2 drive are displayed and the removal of the P2 cards is enabled remove all the P2 cards For Mac OS X 10 5 and 10 6 When P2 cards have been inserted into the device drag the P2 card icons to Trash and check that all targeted P2 card icons have disappeared 2 Press and hold down the power button on the device for 2 seconds to switch off the power
4. out of the reach of babies and small children CAUTION To reduce the risk of fire or electric shock and annoying interference use the recommended accessories only CAUTION The mains plug of the power supply cord shall remain readily operable The AC receptacle mains socket outlet shall be installed near the equipment and shall be easily accessible To completely disconnect this equipment from the AC mains disconnect the mains plug from the AC receptacle E indicates safety information Read this first continue For AJ PCD30P E indicates safety information FCC NOTICE Declaration of Conformity Model Number AJ PCD30P Trade Name Panasonic Responsible Party Panasonic Corporation of North America One Panasonic Way Secaucus NJ 07094 Support contact 1 800 524 1448 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications CAUTION This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful
5. the P2 driver installation manual For Macintosh 1 Insert the supplied CD ROM 2 Double click the Macintosh folder in the CD ROM 3 For Mac OS X 10 5 Double click the Leopard folder For Mac OS X 10 6 Double click the SnowLeopard folder Double click the P2DrivePowerManagement folder 5 Double click P2DrivePowerManagement dmg to open a new window 6 Copy the P2DrivePowerManagement displayed in the opened window to a suitable location such as the desktop Uninstallation For Windows For the uninstallation procedure see the P2 driver installation manual For Macintosh 1 Drag P2DrivePowerManagement to Trash and select Empty trash from the Finder menu 2 Click the OK button in the confirmation window to delete Starting up and shutting down the Power Management Setting Software 1 Check the supplied AC adaptor is connected to the DC IN 16 V terminal of the device 2 Check that the device and your PC are connected by the USB cable 3 Start up your PC and press the power button on the device to switch on 4 Start up the Power Management Setting Software For Windows Select Start gt All programs gt Panasonic P2 gt P2Drive Settings gt Power Management Setting For Macintosh Double click on the application icon 17 Overview of dedicated software continue 5 Check that Connection Status Connected
6. C to the DC IN 12 V terminal of the device oco DCINJ6V DCIN 12V 0000 f power con nector 6 Start the personal computer and verify that it recognises the device lt Notes gt Use a USB cable with a flammability rating of VW 1 For the flammability rating check the printed part of the cover of the USB cable Recommended USB 3 0 cables based on information as of August 2011 Elecom U3C 10BK 1 0 m StarTech com USB3SAB3 0 91 m Recommended cables are listed on the Panasonic website http pro av panasonic net In Windows XP or Windows Vista some card slots of the device may be assigned drive names that have already been assigned to existing networks Reassign network drive names if your personal computer does not display all three card slots Arrange the USB cable so that it does not directly contact the heat sink fan or fins inside your PC 15 P2 Driver Installing a Windows P2 driver Install the P2 driver on the supplied CD ROM on your PC The dedicated software is installed at the same time For the installation procedure see the P2 driver installation manual lt Note gt When installing two or more devices be sure to install the drivers for each device separately Installing a Macintosh P2 driver This driver software enables a Macintosh to access content on a P2 card inser
7. DC 16 V is displayed at the bottom left of the Power Management Setting Software window The device can be set to switch off automatically page 10 6 Shut down the Power Management Setting Software For Windows Click x button at the top right of the window For Macintosh Click x button at the top left of the window Power Management Setting Software window P2Drive Power Management V1 0 X Time to automatic power down Current Settings 4hours O oft O1 hour 2 hours 4 hours O8 hours Connection Status Connected DC 164 Time after which device automatically switches off You can set time after which the power is automatically switched off in an external device power is supplied by the AC adaptor when the P2 card is not accessed to read or write Select from among Off 1 hour 2 hours 4 hours 8 hours The default setting at shipping is 4 hours When the device is connected to your PC externally Connection Status Connected DC 16 V is displayed at the bottom left of the window and the settings can be altered When not connected Connection Status Disconnected is displayed and the settings cannot be altered 18 The current settings of the device are displayed in the Current Settings column To alter the settings select the new settings and then click the Set button The new settings will be enabled when you restart the device After altering the settings swit
8. O 19 To Connect the device to a Personal Canceling P2 drive internal setting 19 Computer for External Use 11 Troubleshooting 20 Disconnect externally connected Specifications 06 21 devices from your PC 13 To Mount the device in a Personal Computer 5 type Bay 14 Microsoft Windows and Windows Vista are trademarks of Microsoft Corporation of the United States Macintosh Mac and Mac OS are trademarks of Apple Inc of the United States Other names of companies and products are trademarks or registered trademarks of the respective companies In these instructions Microsoft Windows Windows XP Professional Windows Vista Business Windows Vista Ultimate Windows 7 Professional and Windows 7 Ultimate are given as Windows Windows XP Professional Windows Vista Business Windows Vista Ultimate Windows 7 Professional and Windows 7 Ultimate respectively Similarly in these instructions Macintosh Mac Pro and Mac OS X are given as Macintosh Mac Pro and Mac OS X respectively Before Use While AJ PCD30 referred to below as the device is connected to the personal computer install the required drivers from the CD ROM For details refer to the installation manual and P2 Driver page 16 in this manual The device may become warm during use but this is not a mal
9. Panasonic Operating Instructions Memory Card Drive Model No AJ PCD30P Model No AJ PCD30E Before operating this product please read the instructions carefully and save this manual for future use SS0611AKO FJ ENGLISH Printed in Japan VQT3R23 Read this first For AJ PCD30P and AJ PCD30E WARNING This apparatus must be earthed To ensure safe operation the three pin plug must be inserted only into a standard three pin power point which is effectively earthed through the normal house hold wiring Extension cords used with the equipment must be three core and be correctly wired to provide connection to earth Wrongly wired extension cords are a major cause of fatalities The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe For your safety if in any doubt about the effective earthing of the power point consult a qualified electrician WARNING To reduce the risk of fire or electric shock do not expose this equipment to rain or moisture To reduce the risk of fire or electric shock keep this equipment away from all liquids Use and store only in locations which are not exposed to the risk of dripping or splashing liquids and do not place any liquid containers on top of the equipment WARNING Always keep accessories rubber feet mounting screws
10. The power indicator on the device will go off 3 Disconnect the USB cable Installation continue To Mount the device in a Personal Computer 5 type Bay 1 Switch off your PC 2 Undo the six screws and remove the cover Cover 3 Mount the device in a 5 type bay on the personal computer If attaching with screws use the mounting screws page 7 supplied with the device Please refer to your computer s instruction manual for guidance in mounting to 5 type bay drives C L o o Holes for securing the screws the other side is the same lt Notes gt The device may not be able to be fastened securely in some types of personal computers Depending on the type of your PC there may not be enough space to fit the device internally In this case use the device externally If all 5 type bays are occupied you will need to remove one of the built in drives to make room for the device The device should be used in a personal computer whose design allows the front panel of the drive to be manipulated 14 4 To be connected by USB 3 0 Connect the B connector of the USB 3 0 cable to the USB 3 0 connector of the device and then connect the other end of the cable to the USB 3 0 port on the motherboard of your PC lt Note gt When there is no internal USB 3 0 connector in your PC run part of the USB 3 0 cable outside your PC once and connec
11. button fully extended This may result in the unintentional ejection of the P2 card or a fault in the EJECT button 1 Flip up the EJECT button in the direction of the arrow T m i oe 2 Press the EJECT button The P2 card will slide out far enough to allow you to remove it ee 0 oo lt Notes gt To remove a P2 card on a Macintosh drag the P2 card icon to the Trash Then check that the icon has disappeared and the access indicator on the device has turned off before physically removing the P2 card Do not remove a P2 card that is being accessed Removing a P2 card during access may cause the device to malfunction Write protection of P2 Card A P2 card has a write protect switch Setting this switch to PROTECT can prevent writing and deleting of data Note The write protect switch is not effective when the P2 card is inserted in the device Make sure you remove the P2 card from the device set the switch then re insert the card in order to effect the switch setting Setting the write protect switch to PROTECT can prevent writing and deleting of data Setting the write protect switch to this side allows writing and deleting of data Power management function automatic switch off function When the device is used externally the power will switch off automatically after four hours if no access is made to t
12. ch the device off and then on again lt Notes gt If you start up the Power Management Setting Software while using the device internally Unable to perform setting changes due to power from DC IN 12 V will be displayed and you cannot alter the settings The automatic switch off function is disabled The Power Management Setting Software does not support connection of 2 of the devices Perform the settings separately for each device Overview of dedicated software continue P2 Drive internal setting Windows When used internally a setting can be made to prevent USB disconnection When the USB connector is inside your PC the USB cable cannot easily be inserted and removed We recommend performing this setting to prevent erroneous disconnection of the USB P2 Drive internal setting When the device is used internally in the 5 type bay of your PC the following settings are performed after connecting the device to your PC 1 From the Start menu select All programs gt Panasonic P2 gt P2Drive Settings and then select Enable Internal Drive 2 A panel of the type shown in the figure will be displayed Click OK on the panel P2Drive Setting e L The P2Drive was set to internal This setting is only available in Windows Canceling P2 drive internal setting To reconnect the device externally to a computer that has been set to use the device internally pe
13. el with its cover removed 1 USB 3 0 connector Type B This connects a USB cable Use a USB cable shielded compliant with USB 3 0 USB 2 0 lt Note gt The device is only compatible with USB 3 0 USB 2 0 It is not compatible with USB 1 1 If you have a Macintosh connect using USB 2 0 2 DC IN 12 V Socket To use the device mounted in a personal computer connect one of the power supply connectors inside the personal computer to this socket page 15 Do NOT supply power to both the DC IN 12 V socket and DC IN 16 V socket at the same time 3 DC IN 16 V Socket For external use of the device connect an AC adaptor to this socket 4 Cable Clamp Use this clamp to secure the AC adaptor cable when connecting the device to a personal computer for external use of the Drive 5 Antitheft Lock A commercially available antitheft cable can be connected to this lock Inserting a P2 Card 1 Insert the P2 card into one of the card slots Press in the card until the EJECT button pops up lt Notes gt Be sure to insert the P2 card horizontally Forcing the card in at an angle may damage it Do not remove a P2 card while it is being accessed or right after insertion Otherwise the card may be damaged Removing a P2 Card 2 Fold the EJECT button in the direction of the arrow OC tr CC DS iim lt Note gt Do not use the device with the EJECT
14. evice is connected to a USB terminal hub then errors may occur such as the computer not recognizing the device or not applying the necessary drivers We cannot guarantee proper operation of the device when connected to a USB hub 3 When using a Macintosh with 2 of the devices connected or with the device and at least two other P2 drive connected avoid duplication among the volume labels of the P2 cards Correct operation cannot be guaranteed if the volume labels are duplicated or left without being set NO NAME is displayed Supplied Accessories AJ PCD30P AJ PCD30E AC adaptor Bracket Mounting page 14 screws 8 Power cable for AC adaptor CD ROM Rubber feet 4 Operating Instructions PDF P2 Software Power Management Setting Software For AJ PCD30E For AJ PCD30E continental Europe etc U K Operating Environment Required for Installation To operate the device the following environment is required on the host computer USB 3 0 port USB 2 0 port The device can be used with a host computer Windows PC that does not have a built in USB 3 0 port by installing a USB 3 0 expansion interface port Note however that Panasonic cannot guarantee correct operation with all third party USB 3 0 expansion interface ports Recommended USB 3 0 expansion interface ports are listed on the Panasonic website http pro av panasonic net The following environ
15. f disposal Panasonic Corporation Web Site http panasonic net Panasonic Corporation 2011
16. function When the device is used internally it may be necessary to connect the device with part of the USB cable passing outside your PC In this case be sure sufficient space behind the PC that is to contain the device Overview The device is a P2 card dedicated data transfer device with a USB 3 0 interface and a 3 slot drive for writing and reading P2 content to and from P2 cards using the USB 3 0 2 0 connection in a Windows PC or Macintosh The device is capable of making high speed transfers of clip data shot with a memory card camera recorder for P2 cards to a personal computer Windows Macintosh This device supports not only the transferring and copying of clips recorded on P2 cards but also direct editing Features It is capable of high speed data transfer of The device can also be connected to a over 1 5 Gbps USB 2 0 Windows PC Macintosh it can be used as either an external or an Up to 2 devices may be connected to a single internal drive only Windows Pc 2 3 Supports both Windows and Macintosh operating systems 1 This is the transfer speed using the multiple P2 card E series over the USB 3 0 connection This will vary according to conditions such as the type of file being transferred the system the application software and the version and the number of the P2 card 2 Connect the USB terminal of the device to your computer using the PC USB port If the USB terminal of the d
17. he P2 cards for reading writing etc To use switch the power on again When the device is used internally the automatic switch off function for power management is disabled Installation lt Note gt You can use the Power Management Setting Software to set the time after which the power is automatically switched off Select from among Off 1 hour 2 hours 4 hours 8 hours The default setting at shipping is 4 hours page 17 Caution If the designated amount of time has passed the device will automatically power off even if you have a file open at the time If that happens the file system may be damaged Handle your files carefully There are two ways to connect the device to a personal computer Windows Macintosh 1 Using the device as an external drive connected to a personal computer Windows Macintosh 2 Mounting the device in a 5 type bay of a desktop personal computer Windows 10 Installation continue To Connect the device to a Personal Computer for External Use 1 Attach the rubber feet to the dimples on the base of the device Dimples 2 Start the personal computer 3 Plug the AC adaptor supplied with the device into the DC IN 16 V socket on the device a d 4 Pressing the power button switches on the power and starts up the device After startup the power indicator will light up green 5 To be connected by USB 3 0 Plug a USB
18. interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help The user may find the booklet Something About Interference available from FCC local regional offices helpful FCC Warning To assure continued FCC emission limit compliance follow the attached installation instructions and the user must use only shielded interface cables when connecting to host computer or peripheral devices Also any unauthorized changes or modifications to this equipment could void the user s authority to operate this device NOTIFICATION Canada This class B digital apparatus complies with Canadian ICES 003 Notice U S A only Di
19. ite http pro av panasonic net 21 Memo 22 Memo 23 Information on Disposal for Users of Waste Electrical amp Electronic Equipment private households This symbol on the products and or accompanying documents means that used electrical and electronic products should not be mixed with general household waste For proper treatment recovery and recycling please take these products to designated collection points where they will be accepted on a free of charge basis Alternatively in some countries you may be able to return your products to your local retailer upon the Say purchase of an equivalent new product Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling Please contact your local authority for further details of your nearest designated collection point Penalties may be applicable for incorrect disposal of this waste in accordance with national legislation For business users in the European Union If you wish to discard electrical and electronic equipment please contact your dealer or supplier for further information Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union If you wish to discard this product please contact your local authorities or dealer and ask for the correct method o
20. ite protect of the P2 cards to the PROTECT side The device is connected using USB 3 0 but your PC is unable to recognize the drive P2 card When the device is connected to a USB 3 0 expansion interface board a dedicated driver must be installed separately 20 Specifications DC 16 V 0 6 A when used with AC adaptor AC adaptor DC 12 V 0 8 A Power Source when mounted in a personal computer AC 100 240 V 1 20 A 50 60 Hz indicates safety information Power Output DC 16 0 V 3 75 A External dimensions W x H x D 148 4 mm x 42 5 mm x199 5 mm indicates safety information 5 7 8 inches x 1 11 16 inches x 7 7 8 inches excluding protruding parts Weight 1 2 kg 2 6 Ib Environmental conditions Operating temperature 0 C to 40 C 32 F to 104 F Operating humidity 10 to 80 w o condensation Personal Computer System Requirements OS proper operation guaranteed Windows XP Professional SP3 32 bit Windows Vista Business SP2 Ultimate SP2 32 64 bit Windows 7 Professional SP1 Ultimate SP1 32 64 bit Mac OS X 10 5 8 Intel processor Mac OS X 10 6 7 Intel processor Main Memory 1 GB or more is recommended Interface USB Ver 3 0 compliant Card slots PC card Type Il x 3 CardBus compliant The latest driver information can be viewed at the following webs
21. ment is recommended for the host computer to make full use of the features of the device A striping configuration using 4 or more hard disk drives is recommended to attain sufficient transfer speed when transferring data to the hard disk drive Parts and their Functions Front Panel 3 4 5 1 Power button Use this button to turn the unit ON and OFF When the power is OFF pressing the power button switches the power ON When the power is ON pressing the power button for two seconds or more switches the power OFF lt Note gt When the device is located internally the device power system is linked to the power system of your PC and the power switches on without pressing the power button on the device Caution Do not switch off the power while the P2 card is being accessed 2 Power Indicator This indicator lights up in green when the device is running 3 Status Indicator This indicator lights up in green during access to a P2 card lt Note gt Do not remove the P2 card during access of the card otherwise files may be corrupted or the P2 card may fail 4 Card Slots The device is designed for P2 cards and does not work with other cards 5 EJECT button Press this button to remove a P2 card from the device Rear Panel oco DCIN16V DCINI2v 0000 5 4 3 2 1 The picture shows the rear pan
22. rform the following 1 Connect the device to your PC externally 2 From the Start menu select All programs gt Panasonic P2 gt P2Drive Settings and then select Disable Internal Drive 3 A panel of the type shown in the figure will be displayed Click OK on the panel P2Drive Setting 1 4 internal setup of P2Drive was canceled 19 Troubleshooting Symptom What to Check Device has been connected using the USB 3 0 cable but transfer is not sufficiently fast The device is connected using a USB 3 0 cable but is being recognized as a USB 2 0 device f the USB 3 0 cable is not properly connected to the USB 3 0 connector of the device the link will be made using USB 2 0 and it will not therefore be possible to obtain a sufficiently high transfer speed Disconnect the USB 3 0 cable and then reconnect ensuring a firm connection P2 cards cannot be accessed after resume from sleep or hibernation Some personal computers may not be able to access a P2 card in the device after resuming from sleep or hibernation After the reconnection switch the device off and then on again Automatic switch off function is not working The automatic switch off function may fail to work due to periodic access to the P2 card by the OS or a resident application In the case of a Macintosh prevent access from the OS by removing the P2 cards or setting the wr
23. sposal may be regulated in your community due to Environmental considerations For disposal or recycling information please visit Panasonic website http Awww panasonic com environmental or call 1 888 769 0149 Read this first continue For AJ PCD30E Caution for AC Mains Lead FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY This product is equipped with 2 types of AC mains cable One is for continental Europe etc and the other one is only for U K Appropriate mains cable must be used in each local area since the other type of mains cable is not suitable FOR CONTINENTAL EUROPE ETC FOR U K ONLY Not to be used in the U K FOR U K ONLY This appliance is supplied with a moulded How to replace the fuse three pin mains plug for your safety and 1 Open the fuse compartment with a convenience screwdriver A 13 amp fuse is fitted in this plug Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSI to BS1362 Check for the ASTA mark amp or the BSI mark Q on the body of the fuse If the plug contains a removable fuse cover you must ensure that it is refitted 2 Replace the fuse when the fuse is replaced If you lose the fuse cover the plug must not be used until a replacement cover is obtained A replacement fuse cover can be purchased from your local Panasonic Dealer E indicates safety
24. t the USB 3 0 cable to the USB 3 0 connector on the back panel A point on the USB 3 0 cable approximately 20 cm from the A connector passes over the notch of the supplied bracket About 20 cm Eo Put the cable in from above Notch After passing the USB 3 0 cable through the slot for attaching the supplied bracket insert the bracket and fix to your PC using the screws supplied with this product Installation continue Connect the USB 3 0 cable to the USB 3 0 port A connector on the back panel of your PC USB cable running outside your PC should be bent so as to describe a shallow curve Sharp bending of the cable may break the wires To be connected by USB 2 0 Connect the B connector of the USB 2 0 cable to the USB 3 0 connector of the device and then connect the other end of the cable to the USB 2 0 port on the motherboard of your PC lt Notes gt When there is no internal USB 2 0 connector in your PC run part of the USB 2 0 cable outside your PC once and connect the USB 2 0 cable to the USB 2 0 connector on the back panel Fora detailed procedure for connection using USB 3 0 refer to To be connected by USB 3 0 page 14 The pin arrangement of the USB 2 0 connector differs depending on the motherboard of your PC After checking the user manual of your PC prepare a commercially available shielded USB 2 0 cable 5 Connect the power connector 4 pin inside your P
25. ted in the device Perform the following steps to install the driver 1 Insert the supplied CD ROM 2 Double click the Macintosh folder on the CD ROM 3 For Mac OS X 10 5 Double click the Leopard folder For Mac OS X 10 6 Double click the SnowLeopard folder 4 Double click the P2Drive folder Double click P2DriveFamilyDriver Install dmg in the P2Drive folder 6 The driver software installation process will now start Follow the instructions given in the installation screen 16 lt Notes gt Without installing the P2 driver a sufficiently high transfer speed cannot be obtained The latest driver information can be viewed at the following website http pro av panasonic net Uninstallation For Windows For the uninstallation procedure see the installation manual lt Notes gt At installation be sure to check that the device is switched on before connecting The P2 driver can be used with either USB 2 0 or USB 3 0 Overview of dedicated software The dedicated application software is used to perform the power management settings and internal settings of the device Power management setting Windows Macintosh When used externally the device may be set to switch off automatically Installation For Windows Install the P2 driver on your computer from the included CD ROM The dedicated software is installed at the same time For the installation procedure see
Download Pdf Manuals
Related Search