ST300-S/SM NS User Manual.
Contents
1. time into the IN Point of the specified register number for the channel with the specified PBIO address RECALL When Recall command is received the channel will cue to the IN point of the specified register number for the specified PBIO address 14 ST304 DSR I K PBIO amp ST304 DSRIK T PBIO Slow Motion Controller Advanced Features 7 TRANSFER CUELIST a TRANSMIT CUE LIST FUNCTION The TRANSMIT CUE LIST function allows you to transmit your list of Cue Points to a PC using the provided utility software on the PC or to another ST300 Transfer to a PC requires OpSuite 3 0 software which runs on a Windows based computer Contact DNF Controls for more information 1 To Transmit Cue Points to Another ST300 a b d 5 Connect the VTR4 connector the rear of the ST300 to the VTR4 connector of the receiving ST300 using an RS422 9 pin cable with TX and RX lines crossed A turnaround cable Press MENU Scroll the Wheel until Transmit CUE list YES Enter Exit ESC is displayed Press ENTER to start transmitting The Display shows Waiting to transmit on the first line When the Receiver is ready transfer starts automatically The Display now shows Transmitting cuelist After the transfer is over the display shows Transfer is over for one second and then shows Waiting to transmit again Connect another ST300 to transmit the list again OR Press2. Manual Version 1 22104 Document ID ST304 DSR1K PBIO User Manual doc 3 ST304 DSR I K PBIO amp ST304 DSRIK T PBIO Slow Motion Controller 1 REVISION HISTORY 102004 1 0 Original document 111804 Rev 1 1 Added GOTO LIVE Section Added Video Standard Selection and INPUT Video Delay Entry to the SETUP MENU 122104 Rev 1 2 Updated GPI Functions 4 ST304 DSR I K PBIO amp ST304 DSRIK T PBIO Slow Motion Controller Getting Started 2 5 SYSTEM DESCRIPTION The ST304 DSR1K Slow Motion Controller combines the power of the 57300 Slow Motion Controller a larger 4 line display and with the power of the Sony DSR DR1000 The key functions e Simultaneous Record and Playback e Segment Playout e Press EE to go to live video DEFINITIONS Throughout this document VTR DDR VDR amp Video Server will be referred to collectively as VTR The ST304 DSRIK will be referred to as ST300 Q Words surrounded by brackets for example ENTER are keys on the ST300 Q XXX XXX means hold the two keys down simultaneously ST304 DSR I amp ST304 DSRIK T PBIO Slow Motion Controller 3 6 INSTALLATION a ST300 INSTALLATION 1 2 3 4 5 6 7 Connect 1 connector on the back of ST300 to the REMOTE OUT Play connector on the DSR DR1000 1 Connect VTR3 connector on the back of the ST300 to the REMOT
3. 2 5v DC 7 Ground 3 Ground 8 Ground 4 12 VDC 9 Ground 5 12 VDC AUX CONNECTOR PBus IN RS422 SERIAL CONNECTOR 9 Pin D Type Female DB9F Pin 1 Frame Ground 6 Common 2 No Connection gi No Connection 3 Receive B 8 Receive A 4 Common 9 Frame Ground 5 Spare 23 ST304 DSR I K PBIO amp ST304 DSRIK T PBIO Slow Motion Controller 24 GPI IN OUT CONNECTOR 15 Pin D Type Female DB15F Pin Description GPI 1 Out GPI 2 Out GPI 3 Out GPI 4 Out GPI 5 Out GPI 6 Out GPI 7 Out Ground JC E Function PLAY tally out STILL STOP tally out RECORD tally out REWIND tally out FFWD tally out SLOMO tally out Description GPI 1 In GPI 2 In GPI 3 In GPI 4 In GPI 5 In GPI 6 In GPI 7 In Function PLAY STOP RECUE NEXT CUE LAST CUE ST304 DSR I amp ST304 DSRIK T PBIO Slow Motion Controller KEY LAYOUT 11 OZOFO LXAN 1571 1 Hvg L Ajuo 5 Ady AJH 941 3 LON 1 9 MLHSQ vOELS NOLLVYNDISNOD 00215 ST304 DSRIK PBIO amp ST304 DSRIK T PBIO Slow Motion Controller 23 12 DNF CONTROLS LIMITED WARRANTY DNF Controls warrants its product to be free from defects in material and workmanship for a period of one 1 year from the date of sale to the original purchaser from DNF Controls In order to enforce the rights under this warranty the customer must first con
4. ESC twice to exit the MENU mode 2 To Transmit Cue Points to a PC a b Connect the VTR4 connector on the back of the ST300 to one of the COM ports on the PC using a RS422 to RS232 adapter Repeat steps a thru g of To Transmit Cue Points to Another ST300 15 ST304 DSR I K PBIO amp ST304 DSRIK T PBIO Slow Motion Controller b RECEIVE CUE LIST FUNCTION The RECEIVE CUE LIST function allows you to receive a list of Cue Points from a PC or from another ST300 Transfer to a PC requires OpSuite 3 0 software which runs on a Windows based computer Contact DNF Controls for more information 1 To Receive Cue Points From Another ST300 a Connect the VTR4 connector on the back of the ST300 from the VTR4 connector of the transmitting ST300 using RS422 9 pin cable with TX and RX lines crossed A Turnaround Cable b Press MENU Scroll the Wheel until Receive CUE List YES Enter Exit ESC is displayed d Press ENTER to start receiving The Display shows Waiting to receive on the first line When the Transmitter is ready transfer starts automatically The Display now shows Receiving cuelist f After the transfer is over the display shows Done Success Press any key g Press any key The display shows Receive cuelist message h Press ESC to exit the MENU mode 2 To Receive Cue Points from the PC a Connect the VTR4 connector on the back of the ST300 to o
5. ST304 DSRIK T PBIO Slow Motion Controller PARITY Select ODD EVEN or NONE This is the parity sent via the Peripheral Bus PBIO to the ST300 SWITCHER Select your switcher type GVG Grass Valley Group default or Sony TYPE For Phillips DD35 with PBus use GVG 20 ST304 DSRIK PBIO amp ST304 DSRIK T PBIO Slow Motion Controller 9 FUNCTION TABLE EE On Off EE Toggle EE mode on off Status indicator is on when EE is on ENTER TIME ENTER TIME To manually enter timecode number into the currently displayed Cue Point enter the desired timecode number using the numeric keypad Press ENTER to save your entry OR ESC to exit without saving To enter a GOTO location without altering the contents of the Cue Point enter the desired timecode number using the numeric keypad Press GOTO to search to the entered time Press ESC to exit without searching DSR START SHIFT RECORD Press SHIFT RECORD to start recording on selected RECORD record channel DSR STOP SHIFT STOP Press SHIFT STOP to stop recording on the selected RECORD record channel FFWD FF WD Press and HOLD to FFWD Release key to stop Set WIND Speed in MENU GOTO CUE GOTO Search the VTR to the IN Point of the currently displayed Cue Point 1 1 R GANG SHIFT VTR 1 Individually press the VTR keys to be included in the gang the LED above the key will turn on Press the VTR key again SHIFT VTR 2 to
6. Recorder For example P 01 12 09 23 R 01 13 09 23 TC Time Modes TM Tape Timer TCZLTC VT VITC The currently selected SLO MO speed is displayed on the far right side of the top row The bottom rows of the display shows the current Cue Point number and its contents or the contents of currently marked IN and OUT points When IN amp OUT LEDs are ON the 3 and 4 lines of the display show the content of current IN amp OUT When IN amp OUT LEDs are off and there is an equal sign between IN OUT and the Timecode the 3 and 4 lines of the display show the content of currently selected cuepoint b TRANSPORT CONTROL Select the desired transport function by pressing the appropriate switch on the ST300 The Real Time Status Indicators will light to indicate the VTR s current tape transport mode For example Pressing PLAY will put the Player into the PLAY mode The PLAY status Indicator will turn on when the VTR is in PLAY mode OR Press SHIFT RECORD to put the Recorder into RECORD mode See SETUP MENU The RECORD status indicator will turn on when the VTR is in RECORD Mode NOTE Check SETUP MENU prior to using the SLOW MOTION CONTROLLER to confirm proper Record mode and other User settable modes 9 ST304 DSR I K PBIO amp ST304 DSRIK T PBIO Slow Motion Controller c IN OUT POINTS 1 Mark IN OUT Point Press SHIFT IN to manually enter the time into the IN point The IN LED tur
7. is pressed the IN is automatically calculated as OUT SEG duration and saved in the cuepoint AUTO MARK allows one key marking of segments by automatically calculating the OUT point You can turn it ON OFF in the Setup Menu 10 ST304 DSRIK PBIO amp ST304 DSRIK T PBIO Slow Motion Controller 11 GOTO PREROLL TO CUE POINT 1 Select the desired Cue Point The Cue number and its contents are shown on the bottom line of the display 2 Press GOTO to search to the IN point saved in the Cue Point After cuepoint is recalled the IN and OUT LEDs are ON PLAYING SEGMENTS 1 Select VTR channel to PLAY 2 Press PLAY key The Player will start playing and it will stop when the time code reaches the OUT point The third line of the display shows Playing Segment If the Player is positioned after the OUT point the playout will continue until STOP is pressed 3 Press PLAY SHIFT to disregard the OUT point and continuously play until STOP is pressed 4 In Variplay SloMo mode the Playback will stop once the time code reaches the OUT point GOTO PREROLL TO A MANUALLY ENTERED TIME 1 2 Press ENTER TIME to use the numeric keypad Manually enter a time on the numeric keypad Press GOTO OR RECUE to search to the entered time OR Press ESC to exit without searching The ENTER TIME indicator will turn off ST304 DSR I K PBIO amp ST304 DSRIK T PBIO Slow Motion Controller j RECORD MODE SEL
8. speed OR 0 gt 100 with a detent at 100 For Wheel only Press Softkey SPDRANGE to select SLOMO speed ranges Press Softkey to select 0 gt 200 OR 100 200 Press Softkey BACK to return to SLOMO MENU Press ESC to exit SETUP MENU OR turn the Wheel to select another item For Wheel only Press Softkey PRSET to select the SLOMO Preset Speed Mode Press Softkey UPDATE When exiting SLOMO mode the last used speed is saved in the Preset Speed register Press Softkey STATIC The Preset Speed register is NOT updated when exiting SLOMO mode It is only changed by SHIFT SLOMO PRESET SLOMO TBAR Press Softkey ON to enable slomo to be engaged by moving the TBAR AUTOENABLE WHEEL Press Softkey JOG or SHUTTLE to enable that function to be engaged by turning the AUTOENABLE Wheel GANG MODE Press Softkey to select PERMANENT GANG described in the FUNCTION Table or TEMPORARY GANG In TEMPORARY mode press and hold the VTR key that you want to read status from then press the VTR s of those VTRs that you want to include in the gang Release the keys The LED on the monitored VTR blinks all other VTRs in the gang stay on constantly To break the temporary gang press any VTR key 18 ST304 DSR I K PBIO amp ST304 DSRIK T PBIO Slow Motion Controller ST300 SETUP ST300 SETUP SetDefault Clear Cues Press Softkey beneath ClearCues to clear all Cue Points to 00 00 00 00
9. 12843 Foothill Blvd Suite Sylmar CA 91342 818 898 3380 voice a 818 898 3360 fax www dnfcontrols com Model No ST304 DSR1K PBIO amp ST304 DSRIK T PBIO for Sony DSR DR1000 DDR SLOW MOTION CONTROLLER WITH SEGMENT PLAYOUT AND PERIPHERAL BUS INTERFACE OPTION USER MANUAL ST304 DSRIK PBIO amp ST304 DSRIK T PBIO Slow Motion Controller 1 Table of Contents 1 REVISION HISTORY GETTING STARTED 2 SYSTEM DESCRIPTION DEFINITIONS 3 INSTALLATION A ST300 INSTALLATION B DSR DR1000 SETUP C PRODUCTION SWITCHER SETUP 4 OPERATION LCD DISPLAY B TRANSPORT CONTROL c IN OUT POINTS D SELECT A CUE POINT SAVE A CUE POINT AUTO MARK OFF F SAVE A CUE POINT AUTO MARK ON G GOTO PREROLL TO A CUE POINT H PLAYING SEGMENTS L GOTO PREROLL TO A MANUALLY ENTERED TIME J RECORD MODE SELECTION 5 DSR DR1000 FUNCTIONS START RECORD B STOP RECORD GOTOEE D GOTOLIVE 6 PRODUCTION SWITCHER FUNCTIONS A TRIGGERS B LEARN C RECALL ADVANCED FEATURES 7 TRANSFER CUELIST A TRANSMIT CUE LIST FUNCTION B RECEIVE CUE LIST FUNCTION 2 ST304 DSR I K PBIO amp ST304 DSRIK T PBIO Slow Motion Controller WD W Ch 15 16 REFERENCE 8 SETUP MENU 9 FUNCTION TABLE 10 SPECIFICATIONS RS422 SERIAL CONNECTOR POWER CONNECTOR AUX CONNECTOR PBus IN RS422 SERIAL CONNECTOR GPI IN OUT CONNECTOR 11 KEY LAYOUT 12 DNF CONTROLS LIMITED WARRANTY
10. E IN Record connector on DSR DR1000 1 Connect VTR2 connector on the back of the ST300 to the REMOTE OUT Play connector on the DSR DR1000 2 Connect VTR4 connector on the back of the ST300 to the REMOTE IN Record connector on DSR DR1000 2 Connect the supplied POWER SUPPLY APX 4108 into the POWER connector on the rear of the ST300 Plug the Power Supply into an outlet 90 VAC 240 VAC Select REMOTE mode on the VTR s front panel Check the SETUP MENU prior to using the Slow Motion Controller to confirm proper Record mode SLO MO speed range and other User settable modes b DSR DR1000 SETUP Select 9 Pin Dual Mode in the DSR DR1000 Interface Setup Menu Refer to the DSR DR1000 User Manual ST304 DSR I K PBIO amp ST304 DSRIK T PBIO Slow Motion Controller PRODUCTION SWITCHER SETUP 1 Connect RS422 9 pin serial cable to the AUX connector on the rear of the ST300 Connect the other end of the cable to the Peripheral Bus Connector on the production switcher Communication Format 38 4K 8 1 2 To select a Production Switcher type Default Grass Valley Group a Press MENU to turn the Wheel until SWITCHER is displayed b Press softkey to toggle between Sony and Grass Valley Press ESC at anytime to exit MENU mode 3 The ST300 has 4 Peripheral Device Addresses one for each VTR that it controls To set the Device Address for each VTR a Press MENU and turn the wheel unt
11. ECTION 1 2 3 4 5 Press MENU The MENU indicator will turn on Turn the Wheel until REC is viewed on the top line of the display The current Record mode is shown Press MENU to select Record Lockout Assemble Crash or Insert Record mode INSERT ONLY Press the desired Softkey to toggle Video Audiol Audio2 Audio3 or Audio4 record on off The Softkeys are located just below the display Follow the line graphic from the bottom of the display to the Softkey Press ESC to exit the MENU The MENU indicator will turn off OR Turn the Wheel for other setup options 5 DSR DR1000 FUNCTIONS a START RECORD 1 2 3 4 Press SHIFT REC on VTRI to start recording on Record channel connected to VTR3 connector of the ST300 The Record LED turns ON Press SHIFT REC on VTR2 to start recording on Record channel VTR4 connector of the ST300 if second DSR is connected The Record LED turns ON b STOP RECORD 1 2 3 A Press SHIFT STOP on VTR1 to stop recording on Record channel connected to VTR3 connector of the ST300 The Record LED turns OFF Press SHIFT STOP on VTR2 to stop recording on Record channel connected to VTR4 connector of the ST300 if second DSR is connected The Record LED turns OFF 12 ST304 DSRIK PBIO amp ST304 DSRIK T PBIO Slow Motion Controller Press EE key to go to Live video on the correspondi
12. Press Softkey YES when asked Are You Sure Press Softkey beneath SetDefault to set ST300 to default settings Press Softkey YES when asked Are You Sure DISPLAY The version number for the currently installed software is displayed SOFTWARE VERSION VIDEO Press Softkey to select NTSC P AL or 24P video standard depending on the standard STANDARD you re using INPUT VIDEO Input Video Delay specifies the time interval between video recorded on the Recorder part DELAY of the DSR being available for playback This parameter is used in GO TO LIVE function The default value is 5 seconds REFERENCE Press softkey to Enable Disable Reference Video VIDEO MARK Q Press Softkey to Enable ADVANCE to next Cue Point when MARK is pressed OR Maintain CURRENT Cue Point when MARK is pressed DROP Press Softkey to select DROP FRAME ON or OFF FRAME Used to preset the VTR s Timecode Generator SEG DURATION Enter SEG duration that will be used to calculate IN OUT point AUTO MARK Press softkey to turn AUTO MARK ON OFF AUTO MARK allows one key marking of segments TRANSMIT Transmits Cuelist to another ST300 or to a PC CUELIST RECEIVE Receives Cuelist from another ST300 or a PC CUELIST PBIO ADDRESS Press VTR key to assign PBIO address Display shows PBIO Address 00 Enter 00 23 Enter address number desired on numeric keypad Repeat for all VTRs assigned 19 ST304 DSR I K PBIO amp
13. il Peripheral Address is displayed b Press VTR 1 or VTR 2 to select VTR c Assign a Peripheral Device Address for that VTR from 0 to 23 by entering the desired address using the numeric keypad Press DEL to turn off the device Any address greater than 23 turns the device off d Select the next VTR and assign a Peripheral Device Address for it e When done press ESC to exit MENU mode 4 Select Parity a Press MENU and turn the Wheel until Parity is displayed b Press Softkey to select ODD EVEN or NONE parity to match the settings on the Production Switcher Press ESC to exit menu mode 5 Configure the production switcher Enable the Peripheral Bus Enable the Peripheral Device Addresses assigned to the ST300 Enable the appropriate Learn Recall levels Enable the Timeline or Recall Trigger function 7 ST304 DSR I K PBIO amp ST304 DSRIK T PBIO Slow Motion Controller Connection Diagram Production Switcher RS422 Cable GPI IN OUT SONY DSR DR1000 2 Remote In R3422 Cable SUPPLY 25422 Cable Remote Out SONY DSR DR1000 1 RS422 Cable Remote In RS422 Cable Remote Out 8 ST304 DSRIK PBIO amp ST304 DSRIK T PBIO Slow Motion Controller 4 OPERATION a LCD DISPLAY During normal operation the top row of the display shows the selected time mode and current time location of the selected Player The second line shows the current time of the
14. ly set IN point IN POINT MARK Save current time as IN point IN POINT Per SETUP MENU the Cue Point Location will advance to the next Cue Point location or remain the same MARK OUT Save current time as OUT point OUT POINT Note OUT point is always saved in the current Cue Point TIME PRESET SHIFT Press to enter Time Preset Generator TIME MODE Press ENTER to load Time Generator with 00 00 00 00 Preset OR enter the time desired via the numeric keypad and press ENTER to load that time OR press ESC to exit without saving 22 ST304 DSRIK PBIO amp ST304 DSRIK T PBIO Slow Motion Controller 10 SPECIFICATIONS Power 90 VAC to 265 VAC adapter supplied with IEC connector Size L x W x H 12 x 6 x 1 5 front 3 0 rear T Bar unit is 12 6 long Weight 4 lbs Rear Panel Connectors VTR1 VTR2 VTR3 VTR4 All DB9F GPL tr needs S DBFI5F POWER E DB9M ER dida DB9F Reference Video BNC Display Easy to read 4 line back lit LCD display User adjustable contrast Jog Shuttle Wheel With mechanical detents Optional T bar Slo mo 0 200 of Play Speed RS422 SERIAL CONNECTOR 9 Pin D Type Female DB9F Pin 1 Frame Ground 6 Receive Common 2 Receive 7 Receive B 3 Transmit B gt 8 Transmit A gt 4 Transmit Common 9 Frame Ground 5 Spare POWER CONNECTOR 9 Pin D Type Male DB9M Pin 1 5v DC 6 5 VDC
15. ne of the COM ports on the PC using RS422 to RS232 adapter b Repeat steps a thru h of To Receive Cue Points From Another ST300 16 ST304 DSR I K PBIO amp ST304 DSRIK T PBIO Slow Motion Controller Reference 8 SETUP MENU Q Press MENU The MENU indicator will turn on Turn the Wheel to select item to change Use the Softkeys to change the desired mode for that option Turn the Wheel at anytime to select another item Press ESC at anytime to exit SETUP MENU The MENU indicator will turn off MENU MODES Turning Wheel Clockwise RECORD Press MENU to select the desired record mode Lockout Assemble Crash Full or Insert Only in INSERT mode Press the associated Softkey located below the display to toggle Video V Audiol A1 Audio2 A2 Audio3 A3 Audio4 A4 on off WIND MODE Press Softkey to select HOLD Fast wind is maintained only while key is pressed OR LATCH Fast wind is initiated and maintained with momentary key press Select fast wind speed 3 9 to 23 7 by pressing Softkey below SPD 17 ST304 DSRIK PBIO amp ST304 DSRIK T PBIO Slow Motion Controller SLOMO ST300 display shows SLOMO with TBAR T Bar version Wheel SpdRange Preset ST300 display shows SLOMO with WHEEL Non T Bar version SpdRange Preset Press Softkey TBAR or WHEEL to toggle between T BAR and WHEEL The T BAR has two speed ranges 0 gt 200 with a detent at 100 play
16. ng Playback Channel The LED turns on When EE light is ON MARK IN and OUT keys mark the Recorder s time code If EE LED is OFF MARK IN and OUT keys mark the Player s Time code d GO TO LIVE 1 Press REC key 2 The Player searches to the current Recorder time minus user defined INPUT Video Delay See SETUP MENU 3 The Player starts playing 13 ST304 DSR I amp ST304 DSRIK T PBIO Slow Motion Controller 6 PRODUCTION SWITCHER FUNCTIONS a 5 The operator fires a trigger using either the Timeline or Run function the production switcher The ST304 puts the DSR DR1000 into the following modes based upon the trigger value GRASS VALLEY GROUP VALUES Trigger Value Mode Play If OUT point set play segment 1 Recue to beginning of clip 2 Slow mo using ST300 Wheel Preset or T Bar Speed 3 Reverse Play 4 Still Frame 5 Play 6 Record 7 or greater Play SONY VALUES Trigger Value Mode 0 Recue to the IN point 1 Play If OUT point set play segment 2 Slo mo using ST300 Wheel Preset or T Bar Speed 3 Reverse Play 4 Still Frame 5 Play 6 Record 7 or greater Play LEARN If the IN and OUT points exists IN and OUT LEDs are on the ST304 saves the current IN and OUT points into the specified register number for the channel with the specified PBIO address If no IN or OUT points exists IN and OUT LEDs are off the ST304 saves the current
17. ns on Press SHIFT OUT to manually enter the time into the OUT point The OUT LED turns on 2 Delete IN OUT Point Press DEL IN DEL 007 The current IN OUT point is deleted IN OUT LED turns off 3 GOTO IN Point Press RECUE to search to currently selected IN point d SELECT A CUE POINT Press NEXT CUE or LAST CUE to step through the Cue Points OR Manually enter the desired Cue Point number using the numeric keypad The current Cue Point number and its contents will be shown on the second line of the display e SAVE A CUE POINT AUTO MARK OFF AUTO MARK allows one key marking of segments by automatically calculating the OUT point You can turn it ON OFF in the setup menu Press IN or MARK to save time into the IN Point of the current Cue Point If EE light is ON Recorder s time will be saved into the IN Point of the Cue Point If Advance option is set time will be saved into the next Cue Point s IN Point Press OUT to save time into the OUT Point of the CURRENT Cue Point If EE light is ON Recorder s time will be saved into the CURRENT OUT Point of the Cue Point Note In order to save an OUT point to the current Cue Point the current Cue Point must have an IN point saved FIRST f SAVE A CUE POINT AUTO MARK ON If AUTO MARK MODE is ON when IN or MARK key is pressed the OUT point is automatically calculated as IN SEG duration then saved in the cuepoint When OUT key
18. ormed by either DNF Controls or its authorized dealer may void the warranty After the warranty period has expired DNF Controls offers repair services at prices listed in the DNF Controls Price List DNF Controls reserves the right to refuse repair of any unit outside the warranty period that is deemed non repairable DNF Controls shall not be liable for direct indirect incidental consequential or other types of damage resulting from the use of the product 26 ST304 DSR I K PBIO amp ST304 DSRIK T PBIO Slow Motion Controller
19. remove from gang the LED above the key will turn off OR Press ESC to exit SHIFT VTR 3 OR The VTR LEDs that are on show the gang SHIFT The flashing LED shows which VTR is currently selected JOG Select JOG mode and enable the Wheel LAST CUE LAST CUE Step to the previous Cue Point Location MARK CUE MARK Save the current time in the currently displayed Cue Point POINT Per SETUP MENU the Cue Point Location will advance to the next Cue Point location or remain the same NEXT CUE NEXT CUE Step to the next Cue Point Location REVERSE REV For T BAR ONLY HOLD key to play video in reverse PLAY RELEASE key to play forward REWIND RWD Press and HOLD to rewind Release key to stop Set WIND Speed in MENU SHUTTLE SHUTTLE Select SHUTTLE mode and enable the Wheel SLOMO SLOMO Press SLOMO to slo mo the VTR Turn the Wheel or move the T Bar to change the play speed Press SLOMO to STILL frame OR press any transport key to exit 21 ST304 DSR I K PBIO amp ST304 DSRIK T PBIO Slow Motion Controller SLO MO SHIFT SLOMO For WHEEL ONLY to preset the slo mo speed Turn the SPEED PRESET Wheel to select desired speed Press ESC OR any transport key to exit STOP STOP Press once to STILL frame VTR Press again to put VTR into STOP mode TIME MODE TIME MODE Press to toggle between Timecode TC VITC VT or Tape SELECT Timer TM display modes GO TO RECUE Press to search to current
20. tact DNF s Customer Support Department to afford the opportunity of identifying and fixing the problem without sending the unit in for repair If DNF s Customer Support Department cannot fix the problem the customer will be issued a Returned Merchandise Authorization number RMA The customer will then ship the defective product prepaid to DNF Controls with the RMA number clearly indicated on the customer s shipping document The merchandise is to be shipped to DNF Controls 12843 Foothill Blvd Suite D Sylmar CA 91342 USA Failure to obtain a proper RMA number prior to returning the product may result in the return not being accepted or in a charge for the required repair DNF Controls at its option will repair or replace the defective unit DNF Controls will return the unit prepaid to the customer The method of shipment is at the discretion of DNF Controls principally UPS Ground for shipments within the United States of America Shipments to international customers will be sent via air Should a customer require the product to be returned in a more expeditious manner the return shipment will be billed to their freight account This warranty will be considered null and void if accident misuse abuse improper line voltage fire water lightning or other acts of God damaged the product All repair parts are to be supplied by DNF Controls either directly or through its authorized dealer network Similarly any repair work not perf
Download Pdf Manuals
Related Search