User Manual - Sitebox Ltd
Contents
1. 5 3 1 The direction of the chuck is controlled by a lever located above the On Off trigger 5 3 2 Forforward rotation move the lever to the left marked with a forwards arrow Fig 7 5 3 3 For reverse rotation move the lever to the right marked with a backwards arrow Fig 8 Fig Fig 8 5 4 Adjusting the drill mode 5 4 1 Locate the selector switch on the top of the drill housing Fig 9 Simply push the selector switch to the left hand side of the drill N with the chuck facing forward to select hammer drilling mode 27 5 4 2 To select normal drilling mode push the selector switch to the 4 right hand side of the drill with the chuck facing forward P Tungsten carbide drill bits are reguired for drilling concrete stone N sa and masonry The best drilling progress is achieved using tungsten LA carbide tipped drill bits Fig 9 5 4 3 Only High Speed Steel HSS drill bits in good condition should be used for drilling metal or wood Spade bits and brad point bits are only used for drilling wood etc 5 5 Tip for Drilling Tiles 5 5 1 Place a piece of masking tape onto the tile in the approximate position for the hole 5 5 2 Mark the position of the hole onto the masking tape this will prevent the drill from skidding across the tile when the drill is started 5 5 3 Set the selector switch to the drill symbol and slowly drill through the tile 5 5 4 When the tile has been full drilled through change t2. HYUNDAI 230V 710W IMPACT DRILL Model HY2158 User Manual License d by Hyundai Corporation Korea HYUNDAI CONTENTS Section Description OWNER S MANUAL amp SAFETY INSTRUCTIONS GENERAL SAFETY OUICK REFERNCE GUIDE UNPACKING AND ASSEMBLY OPERATION GENERAL MAINTENANCE SYMBOLS ENVIRONMENTAL GENPOWER CONTACT DETAILS 10 DECLARATIONS OF CONFORMITY Page 2 Page NS N9s 10 10 10 HYUNDAI 1 OWNER S MANUAL amp SAFETY INSTRUCTIONS 1 1 How to read the manual 1 1 1 Keep this manual for the safety warnings and precautions assembly operation inspection maintenance and cleaning procedures 1 1 2 Write the product s serial number in the back of the manual near the assembly diagram or month and year of purchase if product has no number 1 1 3 Keep this manual and the receipt in a safe and dry place for future reference 1 1 4 The term power tool in the warnings refers to your mains operated corded power tool or battery operated cordless power tool 1 1 5 This combi drill is intended for inserting and removing screws and bolts within the drill s capability 2 GENERAL SAFETY ZN DANGER AA WARNING ZN CAUTION ZN NOTE ALA Non observance Non observance Indicates a hazard NOTE or Read Manual will result in the will result in the which if not IMPORTANT These risk of serious risk of injury to avoided might give details or injury or death to oneself or others result in minor o
3. 4 5 Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools 2 4 6 Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control Page 4 HYUNDAI 2 4 7 Use the power tool accessories and tool bits etc in accordance with these instructions taking into account the working conditions and the work to be performed 2 4 8 Use of the power tool for operations different from those intended could result in a hazardous situation 2 5 Service 2 5 1 Have your power tool serviced by a gualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained 3 QUICK REFERENCE GUIDE and USE PARTS AP Switch Lock 1Keyless Chuck 2 Mode Selector 3 Depth Gauge Button 5 Variable Speed Thumb Grener Ode 7 Forward Reverse 8 Auxiliary Side Handle Wheel Power Switch Lever TECHNICAL SPECIFICATION Drill Er Rated Voltage 230V 50 Hz NE PAINE er Masonry Net Weight Machi Rated Power 710 Watts oer eight Machine 2 45 Kg No Load Speed 0 2 800 min Cable Length 2 metres Impact Rate 0 4 800 bpm Sound Pressure Level 88 dB Lpa Keyless Chuck Size Sound Power Level 99 dB Lwa
4. Paling Eapasiy Into 30 mm Vibration Level 3 579 m s Wood Drilling Capacity into rn Steel Page 5 HYUNDAI 4 UNPACKING and ASSEMBLY A CAUTION This packaging contains sharp objects Take care when unpacking Remove the machine together with the accessories supplied from the packaging 4 1 Unpacking 4 1 1 Check carefully to ensure that the machine is in good condition and account for all the accessories listed in this manual 4 1 2 If any parts are found to be missing the machine and its accessories should be returned together in their original packaging to the retailer 4 2 Assembly A NOTE Before carrying out any assembly or disassembly of the unit please ensure that the unit is not connected to the electrical supply 4 2 1 Do not throw the packaging away keep it safe throughout the guarantee period then recycle if possible otherwise dispose of it by the proper means 4 2 2 Do not let children play with empty plastic bags due to the risk of suffocation 4 3 Fitting the Auxiliary Side Handle Be sure the auxiliary handle is securely tightened against the depth gauge clamp This secures the depth gauge at the desired depth of drilling and also secures the auxiliary handle se 4 3 1 The Auxiliary side handle is attached to the front collar of the drill Loosen the handle assembly by turning the handle clockwise Fig 1 and slide the auxiliary side handle over the keyless chuck onto th
5. e front collar of the drill 4 3 2 Securely tighten by turning the auxiliary handle counter clockwise 4 4 Fitting The Depth Gauge 4 4 1 The drill is supplied with a depth gauge used for drilling holes to a required depth Loosen the auxiliary side handle Fig 1 and insert the depth gauge into the hole on the side of the auxiliary handle Fig 2 4 4 2 Measure back from the drill tip and move the depth gauge back to the required measured depth Securely tighten by turning the auxiliary handle counter clockwise The end of the depth gauge will come into contact with the work surface when the required depth of hole is reached 4 5 Installing drill bits Page 6 HYUNDAI Always disconnect the machine from the power supply before adjustment changing accessories and maintenance 4 5 1 The keyless chuck fitted to this impact drill allows for the easy installation and removal of bits and drills The chuck has two rotating grips Fig 3 1 amp 2 4 5 2 Select the drill driver bit required and insert it into the chuck jaws turn grip 1 in a clockwise direction until jaws grip the drill driver bit With your free hand hold grip 2 firmly and rotate grip 1 in a clockwise direction until it tightens onto the drill driver bit Do not use unnecessary force to tighten Fig 3 5 OPERATION Before connecting the impact drill to a power supply make sure it is not in the locked on position Failure to do so could resu
6. e tool using compressed air 6 5 Lubrication 6 5 1 All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions Therefore no further lubrication is reguired 7 SYMBOLS 7 1 The rating plate on this product may show some or all of the following symbols 7 2 These represent important information about the product or instructions on its use Wear hearing protection Wear eye protection Wear respiratory protection Conforms to relevant safety Double insulated for Read the instruction manual standards additional protection Waste electrical products should not be disposed of with household waste General warning Please recycle where facilities exist Check with your Local Authority or retailer for recycling advice Product conforms to RoHs requirements Page 9 HYUNDAI 8 10 ENVIRONMENTAL 8 1 Do not dispose of electric eguipment together with household waste material In observance of European Directive 2012 19 EC on waste electrical and electronic eguipment and its implementation in accordance with national law electric equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility If electrical appliances are disposed of in landfills or dumps hazardous substances can leak into the groundwater and get into the food chain damaging you
7. he selector switch to the hammer symbol and continuing with hammer drilling 5 6 Tip for Drilling Metal 5 6 1 When drilling metal use a light oil on the drill bit to keep it from overheating 5 6 2 The oil will prolong the life of the bit and increase the drilling action Page 8 HYUNDAI 5 7 Work piece Clamping 5 7 1 To prevent the work piece from spinning if drill bit becomes jammed it is recommended that a drill vice or other suitable clamp is used to secure the work piece during the drilling operation 6 GENERAL MAINTENANCE Do not at any time let brake fluids petrol petroleum based products penetrating AN WARNING oils etc come in contact with plastic parts Chemicals can damage weaken or destroy plastic which may result in serious personal injury 6 1 Avoid using solvents when cleaning plastic parts Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use Use clean cloths to remove dirt dust oil grease etc 6 2 Electric tools used on fiberglass material wallboard compounds or plaster are subject to accelerated wear and possible premature failure because the fiberglass chips and grindings are highly abrasive to bearings brushes commentators etc 6 3 Conseguently we do not recommended using this tool for extended work on these types of materials 6 4 However if you do work with any of these materials it is extremely important to clean th
8. lt in accidental starting of the drill resulting in possible serious injury 5 1 Switching impact drill ON and OFF 5 1 1 This machine is fitted with a continuous operation button To start the machine squeezes the On Off trigger Fig 4 pr 5 1 2 When the machine starts press in the continuous operation Ed button located on the side of the handle Fig 5 release the On Off trigger 5 1 3 The machine will now run continuously without the need to maintain pressure on the On Off trigger 5 1 4 To stop the machine briefly squeeze then release the On Off trigger 5 2 Variable Soeed Control 5 2 1 Light pressure on the On Off trigger results in low speed allowing drilling to begin in a smooth controlled manner Further pressure on the switch results in an increase in speed 5 2 2 The desired speed can be pre selected with the thumb wheel Fig 6 also possible during operation The rotational speed to be used depends upon the material being drilled Fig 6 Page HYUNDAI 5 3 Changing the Rotation ZN WARNING The impact drill is not designed for reverse hammering Failure to heed this warning may result in damage to the drill The design of the switch will not permit changing the direction of rotation while the drill is running Release the On Off trigger and allow the drill to stop before changing its direction The impact drill will not run unless the lever is pushed fully to the left or right
9. r further oneself or others moderate injury information on what has already been said and aim to prevent damage to the machine or cause other damage DO NOT let comfort or familiarity with product gained from repeated use replace A WARNING strict adherence to safety rules for the subject product MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury 2 1 Work Area Safety 2 1 1 Keep work area clean and well lit Cluttered or dark areas invite accidents 2 1 2 Do not operate power tools in explosive atmospheres such as in the presence of flammable liduids gases or dust Power tools create sparks which may ignite the dust or fumes 2 1 3 Keep children and bystanders away while operating a power tool Distractions can cause you to lose control 2 2 Electrical Safety 2 2 1 Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock 2 2 2 Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded 2 2 3 Page 3 HYUNDAI 2 2 4 Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock 2 2 5 Donot abuse the co
10. r health and well being 8 2 For further information on the disposal of this product please contact your dealer or your nearest domestic waste collection service 3 Reduce Reuse Recycle unwanted materials instead of disposing of them as waste All tools accessories and packaging should be sorted taken to a recycling centre and disposed of in a manner which is compatible with the environment 8 3 TY r 84 N J When the product is no longer required it must be disposed of in a manner which is compatible with the environment GENPOWER CONTACT DETAILS 9 1 Postal address Genpower Limited Isaac Way Pembroke Dock Pembrokeshire SA72 4RW UK 9 2 Telephone contact number Office 44 0 1646 687880 9 3 Email contact Technical service genpower co uk 9 4 Web site www hyundaipowerequipment co uk DECLARATIONS OF CONFORMITY 10 1 Genpower Ltd confirms that this Hyundai product conform to the following CE Directives 10 1 1 2006 42 EC Machinery Directive 10 1 2 2004 108 EC EMC Directive 10 1 3 2006 95 EC Low Voltage Directive Page 10 HYUNDAI Page 11 HYUNDAI Page 12 HYUNDAI GENPOWER LTD Isaac Way Pembroke Dock Pembrokeshire UK SA72 4RW T 44 0 1646687 880 F 44 0 1646686198 E sales genpower co uk www hyundaipowerequipment co uk
11. rd Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges and moving parts Damaged or entangled cords increase the risk of electric shock 2 2 6 When operating a power tool outdoors use an extension cord suitable for outdoor use 2 2 7 Use of a cord suitable for outdoor use reduces the risk of electric shock 2 2 8 If operating a power tool in a damp location is unavoidable use a residual current device RCD protected supply Use of an RCD reduces the risk of electric shock 2 3 Personal Safety 2 3 1 Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury 2 3 2 Use personal protective eguipment Always wear eye protection Protective eguipment such as dust mask non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce personal injuries 2 3 3 Prevent unintentional starting Ensure the switch is in the off position before connecting to power source and or battery pack picking up or carrying the tool Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents 2 3 4 Remove any adjusting key or wrench before turning the power tool on A wrench or a key left at
12. tached to a rotating part of the power tool may result in personal injury 2 3 5 Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations 2 3 6 Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts 2 3 7 If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of dust collection can reduce dust related hazards 2 4 Power Tool Use and Care 2 4 1 Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed 2 4 2 Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired 2 4 3 Disconnect the plug from the power source and or the battery pack from the power tool before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally 2 4 4 Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users 2
Download Pdf Manuals
Related Search