VP100user manual
Contents
1. VP 100 USER S GUIDE Introduction The VP100 is a high performance and reliability Two Tone Sequential Coding Tone and Voice Pager This pager has been designed for easy of use Battery Installation Install your battery as follows 1 Slide the battery door look switch to Unlock 2 Follow by then to open the battery door See Figure 2 3 Observing the correct polarities install the battery AA into the battery compartment 4 Close the battery door push down into place then slide the battery door to close slide the Battery door lock switch to Lock Note Ifa NiHm battery installed You may need to recharge the battery first to ensure optimum battery capacity and performance Please use the desk charger for VP100 See Figure 1 Unlock Battery door Figure Figure 2 Turn the pager on 1 On mode Volume Sliding the 3 position switchinan Control upward direction two notches will place the pager in the ON mode Refer to figure 3 2 Silent mode Sliding the 3 position switch in an upward direction one notches will place the pager in the Silent mode Refer to figure 3 External speaker Jack Reset SW ON OFF SWITCH Battery Condition Check Immediately after the pager is placed in the ON or Silent mode the pager will automatically test the condition of the battery Figure 3 ON mode A good battery is indicated by a power up alert double interrupted 8 beep t2. l continue to be heard Your pager comes with the follow standard features Automatic Listen Manual Reset A voice message will immediately follow the alert tone After the voice message the pager monitors the channel unless the RESET switch is pressed and released Battery Level Check and Monitor Each time the pager is turned on or the RESET switch 1s pressed and released the battery level is checked refer to Battery Test in table 1 If the battery voltage drops below a minimum level approximately 1 1 volts an automatic low battery warring will be heard which is a 1 second fast pulsating beep If you hear this alert you should replace the AA size alkaline battery If you use the rechargeable battery you should be recharged Unread Message Indicator The red LED turns on if there are any unread message Reminder Alert The paging device generates a reminder alert approximately every two minutes when an unread message exists Stored Voice Model Features and Controls The alert monitor with stored voice stores up to 2 minutes of voice message Messages are stored according to their length See Option OPTIONS External Speaker Jack When a pager is used in a high noise environment an optional speaker or earpiece can be connected to the external accessory jack located on the top control panel The jack is fitted with a protective plug Note To prevent entry of dust and moisture the protective plug should be used wheneve
3. one Alamp on top of the pager will flash along with any alert tones as additional indicator A low battery 1s indicated by a fast pulsating beep and flashing lamp 1 second duration immediately follow the power up alert Silent mode A good battery is indicated by a double interrupted flashing light 2 second duration If equipped with the Vibration mode a good battery 1s indicate by continuous vibration and a double interrupted flashing light 2 second duration A low battery 1s indicated by a fast pulsating beep and flashing lamp 1 second duration immediately following the power up lamp or vibration Volume Check and Adjustment In the ON mode adjust the volume control for a comfortable listening level during the 2 second power up alert To check volume at a time other than power up press the reset switch This will result in channel communication noise which verifies volume setting or allows adjustment to amore comfortable listening level if required Channel audio will not be heard when equipped with the Private Message Only Option Instead a short beep tone will allow you to verify and adjust the volume setting Paging Operation When a page is received in the ON mode the pager emits an alert tone followed by a voice message When the voice message 1s complete press and release the RESET switch The pager is now in a standby condition ready to receive the next page If the pager is not reset all message and channel noise wil
4. r the external speaker jack is not being used Fix Alert Audio Only Volume Control When this option is installed the alert tone volume is factory preset non adjustable at the maximum volume level Turning the volume control will only the voice message volume level Note if you are using the earphone we are not recommended with this option Push To Listen When this option the voice message following the alert tone will not be heard unless the operator immediately holds the RESET button Private Message Only Pagers with this option installed are capable of receiving only those messages intended for the individual user The RESET button will not allow channel monitoring and the pager will automatically reset to the standby mode after a message is received If the RESET button is pushed before the end of a message the radio returns to standby and the rest of the message is lost Group Call With this option the pager will emit either the standard alert tone interrupted tone or an additional group call alert continuous tone The group call alert indicates that the paging message is intended for all members of a particular group Stored Voice Model Features and Controls The alert monitor with stored voice stores up to 2 minutes of voice message Messages are stored according to their length If pre freed the alert monitor can be programmed for stored voice fixed message length of 30 60 120 second Message can be deleted by ei
5. ther incoming new message replacing older messages or by turning the receiver off
Download Pdf Manuals
Related Search