Instruction Manual
Contents
1. Power Filter by breaking off the leveler bar at base of motor a Fill Power Filter case completely with water and replace cover b Adjust water flow control lever on intake U tube to its maximum position for initial start up c Plug power cord into electrical outlet Allow 30 45 seconds for priming air to be expelled from U tube w gt d After priming has been completed move adjustment control on intake SS U tube to adjust water flow rate as required See How it Works Patented Refiltration System IMPORTANT DO NOT OPERATE FILTER WITHOUT WATER NOTE For maximum filter operation and efficiency regular cleaning of the filter and its parts is recommended every two weeks Soap or detergents are NOT recommended for filter maintenance See Power Filter Maintenance Q A Q TROUBLESHOOTING amp FAQs What if the Power Filter motor doesn t start or makes a mechanical noise Check to make sure impeller blades are free moving on magnet assembly Why won t the Power Filter motor re start after performing filter insert maintenance Make sure unit has been plugged back into power outlet and that all parts are thoroughly clean and replaced as directed See Power Filter Maintenance What should do if the priming process doesn t occur Verifiy that e all parts are installed correctly e filter case is completely filled with water unit is plugged into power outlet e ensure2. AGuUaGlear Power Filter Instruction Manual Voir instructions en fran ais l int rieur See inside for Quick Start Guide Models 20 30 50 70 and 110 IMPORTANT SAFEGUARDS WARNING To guard against injury basic safety precautions should be observed including the following 1 For the complete enjoyment use and understanding of this product READ AND FOLLOW ALL SAFETY INSTRUCTIONS and all important notices on the AquaClear Power Filter before using Failure to do so may result in damage to the unit DANGER To avoid possible electrical shock special care should be taken since water is employed in the use of this equipment For each of the following situations do not attempt repairs yourself return the AquaClear Power Filter to an authorized service facility for service or discard the appliance If the AquaClear Motor Unit falls into the water DO NOT reach for it First unplug it and then retrieve it If any electrical component of the AquaClear Power Filter gets wet unplug it immediately If the AquaClear Motor Unit shows any sign of abnormal water leakage or if RCD or GFCI Ground Fault Current Interrupter switches off disconnect the power supply cord from mains and remove pump from water Carefully examine the AquaClear Power Filter after installation It should not be plugged in if there is water on parts not intended to be wet Do not operate any appliance if it has a damaged c
3. U tube lever is set to maximum position Why is the water cloudy in my new aquarium Bacterial cloudiness may occur during the first week of a new aquarium set up and may last up to six weeks If the condition persists consult your local aquarium professional What happens if forget to clean my filter inserts If the Power Filter is left unattended for too long the filter inserts become clogged with debris In extreme cases the filter basket may be forced up from the filter case due to the pump pressure This is an indication that the efficiency of the filtration is very low and that the filter inserts require immediate rinsing or replacement See Filter Inserts Maintenance When should operate a reduced flow Reduced flow is most helpful during feeding times or when the input suction or output stream is too strong for small or delicate fish See How it Works Patented Refiltration System Why should I use only aquarium water to rinse my filter inserts after they are installed Most cities add chlorine or other chemicals to eliminate harmful bacteria in drinking water for human consumption These additives while harmless to us are very toxic to fish
4. ation by trapping particles and debris as they pass through the insert This unique foam designed for use with AquaClear Power Filters features optimal pore size for efficient mechanical and biological filtration Stage 2 Chemical Activated Carbon Filter Insert AquaClear Activated Carbon Filter Inserts contain 100 premium research grade carbon Premium research grade carbon provides large amounts of surface area for adsorption of undesirable impurities The Activated Carbon Filter Inserts will remove unwanted odors discoloration and impurities resulting in a crystal clear aquarium Stage 3 Biological BioMax Insert AquaClear BioMax Filter Inserts contain BioMax ceramic rings The surface of BioMax is made up of a complex pore system that allows bacteria to thrive Use of the BioMax Filter Insert will provide optimal living space for beneficial bacteria and enhance the removal of ammonia and nitrites resulting in a healthy aquarium environment NOTE Regular replacement of AquaClear Filter Inserts is essential for optimum filter performance PATENTED REFILTRATION SYSTEM For a healthy aquarium and clear water Sometimes delicate fish and plants require a gentler water flow The patented AquaClear refiltration system allows you to control the flow rate without compromising filtration efficiency When the flow rate is reduced up to 50 of the water within the filter chamber is processed multiple times More impurities are filtered
5. disconnect Always unplug an appliance from an outlet when not in use Do not use this pump for other than intended use i e do not use in swimming pools bathrooms etc The use of attachments not recommended or sold by the appliance manufacturer may cause an unsafe condition Do not use this pump in swimming pools or other situations where people are immersed e This pump is suitable for use in water temperatures up to 35 C A Do not use this pump with inflammable or drinkable liquids 7 This pump is suitable for INDOOR use only Do not install or store the appliance where it will be exposed to the weather or to temperatures below freezing 8 Make sure an appliance mounted on a tank is securely installed before operating it 9 Read and observe all the important notices on the appliance 10 If an extension cord is necessary a cord with a proper rating should be used A cord rated for less amperes or watts than the appliance rating may overheat Care should be taken to arrange the cord so that it will not be tripped over or pulled The connection should be carried out by a qualified electrical installer 11 The pump must not run dry SAVE THESE INSTRUCTIONS For the complete use and understanding of this power filter it is recommended that this manual is thoroughly read and understood Failure to do so may result in damage to this filter HOW TO CONTACT US If you have a problem or have questi
6. ekly maintenance AquaClear Power Filter Quick Start Guide PACKING LIST Congratulations on the purchase of your new AquaClear Power Filter Please allow approximately 15 20 minutes for the complete installation of filter parts and inserts The rewards to your aquatic adventures will be worth it Inspect AquaClear Power Filter for any visible signs of shipping damage and verify that motor is securely fastened to filter case The following parts should be included in your package __ Filter Cover Leveling Device Mesh Bag A LED Re ALAN SASS ALES All AquaClear Power Filters except Model 20 are shipped with two extension tubes PREPARING FILTER INSERTS ALL FILTER INSERTS MUST BE RINSED THOROUGHLY PRIOR TO INSTALLATION AquaClear BioMax Filter Insert Open poly bag and transfer contents into mesh bag Apply locking clip as shown trim excess mesh and thoroughly rinse insert materials before placing on third level of the basket Replace BioMax Insert every three months NOTE Regular replacement of AquaClear filter inserts is essential for optimum filter performance AquaClear Foam Filter Insert Rinse Foam Filter Insert and place into filter basket first The foam block should totally fill the bottom of the basket leaving no space between the filter basket base and sides Replace Foam Filter Insert every two months AquaClear Activated Carbon Filter Insert Remove Activated Carbon Insert
7. er contained in the aquarium and is limited to the Power Filter unit only The motor is factory sealed tampering will void guarantee REGISTER ON LINE www hagen com e To learn more about Hagen products e For a copy of our FREE full color 40 page Basic Aquarium Guide Canada only HOW IT WORKS The AquaClear Power Filter draws water from the aquarium through an extension tube into the motor which then pumps water out of the impeller assembly The intake U tube directs the flow of unfiltered water through filter inserts to trap particles debris and purify the water CYCLEGUARD MULTI STAGE sys FILTRATION SYSTEM i Bi J Provides optimal Mechanical Chemical g and Biological filtration F A healthy aquarium requires beneficial bacteria Invisible and harmless beneficial bacteria are essential in the removal of toxic ammonia and nitrite With cartridge filtration systems when you throw away the cartridge you throw away beneficial bacteria It can take weeks for the bacteria to recolonize resulting in a stressful environment The AquaClear multi stage filtration system is different Only one of three filtration components is changed at a time This ensures that significant amounts of beneficial bacteria remain There is never a sudden depletion of bacteria so biological filtration remains at highly effective levels Stage 1 Mechanical Foam Filter Insert AquaClear Foam Filter Inserts perform mechanical filtr
8. from protective plastic bag and rinse pouch to remove any carbon dust particles Flatten insert and place horizontally on top of Foam Filter Insert Replace Activated Carbon Insert every month FILTER INSERTS MAINTENANCE AquaClear Foam Activated Carbon and Biomax Inserts should be changed alternately in order to maintain continuous biological activity Follow individual packaging instructions for recommended replacement intervals Never replace all Filter Inserts in any AquaClear Power Filter at the same time 3 INSTALLING FILTER INSERTS After preparing filter inserts as indicated place filter basket into filter case Gentle pressure may be necessary to ease filter basket into position due to the snug fitting Foam Filter Insert 4 ATTACHING INTAKE U TUBE a Install intake U tube as shown and apply gentle pressure to click into position b Additional slight pressure is then applied to ensure base of tube clicks into the opening over impeller cover c Attach extension tube on aquarium side of intake d Add more than one extension tube if tank depth requires it Power Filter must be level to ensure optimal performance Insert leveling device into bottom of filter case Mount Power Filter onto rear of aquarium and adjust leveling device by turning to required setting NOTE If necessary an additional adjustment may be made to level
9. ons about the operation of this product please let us try to help you before returning product to your dealer Most problems can be handled promptly with a toll free phone call Or if you prefer you can contact us on our web site at www hagen com When you call or write please have all relevant information such as model number and or part numbers available as well as the nature of the problem CANADA CALL US ON OUR TOLL FREE NUMBER 1 800 554 2436 between 8 30 a m and 5 00 p m Eastern Standard Time Ask for Customer Service U K HELPLINE NUMBER 01977 556622 between 8 30 a m and 5 00 p m Eastern Standard Time Ask for Customer Service FOR AUTHORIZED WARRANTY CUSTOMER SERVICE CANADA Return unit with dated receipt plus 4 00 for shipping and handling to Rolf C Hagen Inc 3225 Sartelon St Montreal Quebec H4R 1E8 U K Return unit well packaged and by registered post enclosing dated receipt and reason for return to Rolf C Hagen UK Ltd California Dr Whitewood Ind Est Castleford West Yorkshire WF10 5QH WARRANTY The AquaClear Power Filter is unconditionally guaranteed for defects in material and workmanship for a period of two years from date of purchase This guarantee is valid only under normal operating conditions for which the Power Filter is intended This guarantee will not apply to any unit subjected to improper use negligence or tampering This guarantee does not include responsibility for animate matt
10. ord or plug or if it is malfunctioning or if it is dropped or damaged in any manner The power cord of this appliance cannot be replaced if the cord is damaged the appliance should be discarded Never cut the cord To avoid the possibility of the AquaClear Power Filter s plug or receptacle getting wet position the unit to one side of a wall mounted receptacle to prevent water from dripping onto the receptacle or plug A drip loop A should be arranged to the receptacle The drip loop is the part of the cord below the level of the receptacle or the connector if an extension cord is used to prevent water traveling along the cord and coming into contact with the receptacle If the plug or receptacle does get wet DO NOT unplug the cord Disconnect the fuse or circuit breaker that supplies power to the appliance Then unplug and examine for presence of water in the receptacle Close supervision is necessary when any appliance is used by or near children To avoid injury do not contact moving parts or hot parts such as heaters reflectors lamp bulbs etc CAUTION Always unplug or disconnect all appliances in the aquarium from electricity supply before placing hands in water before putting on or taking off parts and whilst the equipment is being installed maintained or handled When inserting or removing the pump from the water always pull out the main electricity plug Never yank cord to pull plug from outlet Grasp the plug and pull to
11. our filtration system AquaClear Ammonia Remover Filter Insert Removes and controls harmful ammonia e Ideal for new or heavily populated aquariums e Reduces stress on fish e For freshwater use only AquaClear Ammonia Remover Filter Insert contains a natural ammonia removing resin This resin chemically bonds with ammonia to remove it from the aquarium water Use of the Ammonia Remover Filter Insert will reduce and control toxic ammonia resulting in a healthy aquarium environment AquaClear Zeo Carb Filter Insert Combines activated carbon and ammonia remover in one e Removes toxic ammonia odors discoloration and impurities e For use to prevent buildup of toxic ammonia Reduces stress on fish e For freshwater use only AquaClear Zeo Carb Filter Insert contains a mixture of ammonia removing resin and premium research grade carbon This dual purpose insert gives you the combined benefits of carbon and ammonia remover while allowing you additional space in your filter for other types of inserts NUTRAFIN WATER CARE PRODUCTS For Improved Aquarium Health AquaPlus Patented stress relief water conditioner Makes tap water safe Protects fish and helps heal damaged fins cuts and wounds Ideal for new tank set up and water changes Cycle Biological aquarium supplement introduces beneficial bacteria to accelerate the maturation of new tanks Promotes tank health and reduces fish loss when used as part of we
12. out creating a healthier tank with sparkling clean and clear water NOTE A reduced flow rate is also recommended for use during feeding to ensure more efficient food consumption and less waste AQUACLEAR POWER FILTERS FLOW RATES MODEL 20 30 50 70 110 Maximum Flow Rate 100 gph 150 gph 200 gph 300 gph 500 gph 378 Iph 568 Iph 757 Iph 1135 Iph 1890 Iph Minimum Flow Rate 33 gph 50 gph 66 6 gph 100 gph 166 6 gph 125 Iph 190 Iph 250 Iph 380 Iph 630 Iph Watts 6 Watts 6 Watts 6 Watts 6 Watts 14 Watts RPM 3600 rpm 3600 rpm 3600 rpm 3600 rpm 3600 rpm POWER FILTER MAINTENANCE Always unplug the Aquaclear Power Filter prior to cleaning Remove cover filter basket and discard water remaining in the filter case Thoroughly rinse collected debris from the case impeller cover and impeller assembly in clear lukewarm water The intake U tube and extension tube can be cleaned with a filter stem brush to remove any buildup of deposits When all parts have been cleaned and thoroughly rinsed reassemble filter and replace onto aquarium See Quick Start Guide 2 3 and 4 Follow operating instructions to restart and prime Power Filter See Power Filter Start Up Every three months the motor should be thoroughly cleaned Remove cover filter basket and discard water remaining in filter case Remove motor by twisting a 1 4 turn gently in the direction of the arrow on front Ease motor down slowly to prevent damage to the filte
13. r and motor guide Pull impeller out of impeller well and rinse to remove accumulated slime deposits A cotton swab or impeller well brush not supplied can be used to remove more stubborn deposits Wet motor seal ring to prevent damage before placing into filter case REPLACEMENT PARTS To re order parts for your AquaClear Power Filter please refer to Parts List below NEW MODEL 20 30 50 70 110 Formerly model Mini 150 200 300 500 Article A 595 A 600 A 610 A 615 A 620 A Filter Case A 16020 A 16120 A 16220 A 16320 A 16420 B Filter Basket A 16040 A 16140 A 16240 A 16340 A 16440 C Filter Cover A 16030 A 16130 A 16230 A 16330 A 16430 D Intake U Tube A 16050 A 16150 A 16150 A 16350 A 16350 E Extension Tube A 625 A 625 A 625 A 627 A 627 F Impeller Cover A 16015 A 16015 A 16015 A 16315 A 16415 G Impeller Assembly A 630 A 632 A 634 A 636 A 638 H Seal Ring A 16017 A 16017 A 16017 A 16017 A 16417 Motor Unit A 16000 A 16000 A 16000 A 16000 A 16400 J Leveling Device A 16325 A 16325 A 16325 A 16325 A 16325 Intake U Tube Adaptor N A N A N A N A A 16412 Not shown Available for Model 110 only ALSO AVAILABLE FROM AQUACLEAR Occasionally it might be necessary to use alternate filter inserts to maintain a well balanced healthy aquatic environment We offer the following alternative chemical stage inserts as superior solutions to y
Download Pdf Manuals
Related Search