Industrial Solar Power PoE Switch BSP
Contents
1. Industrial Solar Power PoE Switch BSP 300 Quick Installation Guide Safety Precautions Please read before using 1 All electrical work must be done in accordance with local and or international electrical codes 2 Before installing or using this device read all instructions and cautionary marking located in or on this guide the controller the batteries PV Photovoltaic array and any other device used 3 To reduce the risk of short circuits use insulated tools when installing or working with the inverter the controller the batteries or any DC source e g PV 4 Remove all jewelry This will greatly reduce the chance of accidental exposure to live circuits 6 The controller contains more than one live circuit batteries and PV array Power may be present at more than one source 7 This product contains no user serviceable parts Do not attempt to repair this unit unless fully qualified 1 Package Contents 2 Overview 3 Hardware Installation Further Information Table of Contents 1 Package Contents e i x BSP 300 e 1 x Quick Installation Guide 1 x RS232 Console Cable e i x CD e 2 x Rack Ear e i x Screw Kit 2 Overview System LED FAULT LED 10 100 1000Base T PoE port x 2 Link ACT LED PoE in Use LED 10 100Base TX Link ACT LED 1000Base T Link ACT LED 4 Pin Terminal PV In Battery In Out 10 100 1000Base T port RJ 45 typ2. e RS 232 Console Block LED Definition LED Status Description Slow Blink System On System Fast Blink The battery is Charging Slow Blink The PV disconnects Fault Fast Blink The battery voltage is less than the value for low voltage disconnection On Bad Battery Over current Short circuit Link ACT On The 10 100 1000Base T PoE port is link up For Port 1 2 Blink The BSP 300 is actively sending or receiving data over that port On A PoE device is detected PoE in Use Off No PoE device attached The port is running in 1000Mbps speed and On A 1000 successfully established Blink The BSP 300 is actively sending or receiving data over that port Link ACT On The port is running in 10 100Mbps speed and successfully established glia The BSP 300 is actively sending or receivin For Port 3 Blink 4 g 3 data over that port SE 3 Hardware Installation Solar Power System Long range Wireless Backhaul Bridge Wireless CPE AP Solar PV Battery BSP 300 Ethernet Extender Laptop DC Powered Device Local Console _ 1000Base T UTP with PoE b EI Serial Line RS XXX 1000Base T UTP _ Power Line DC Please follow the following steps sequence to install the system Step 1 Install BSP 300 Fix BSP 300 to desired location with wall mount fixture Please install the BSP 300 in a proper enclosure o
3. external device should also be grounded properly After the 5 steps above the BSP 300 is ready for service Further Information For more information about this Solar Power PoE Switch please refer to the user manual from the supplied CD ROM
4. r shelter The BSP 300 must be grounded Step 2 Install battery 1 2 3 Bat In Out Battery Connect the negative electrode of the battery to the terminal for the negative electrode of the battery on the BSP 300 Connect the positive electrode of the battery to the terminal for the positive electrode of the battery on the BSP 300 After the battery is well connected to the BSP 300 the System LED will ON with slow blinking for system ready and the Fault LED will slow blinking for PV not connected e Be noted for the thickness of electric wire and please refer to the section Recommended Use of the Connection Wires of the user manual e The BSP 300 accepts DC 24V battery system please pay atten tion to the battery characteristics and also refer to the section Recommended Settings for Different Batteries of the user manual e Check the total power consumption of your connected network device before installation Improper battery capacity could shorten the battery life or make your network device lack of power supply Step 3 Install PV panel Solar PV 1 Connect the negative electrode of the PV panel to the terminal for the negative electrode of the PV panel on the BSP 300 2 Connect the positive electrode to the terminal for the positive electrode of the PV panel on the BSP 300 3 After the PV is well connected to the BSP 300 and providing 24V or above voltage
5. the System LED will fast blinking for battery charge if the battery is not full And turn off the fault LED e Be noted for the thickness of electric wire and please refer to the section Recommended Use of the Connection Wires of the user manual e The BSP 300 supports maximum 45V DC input please refer to the Specification of the user manual before installation e Check the total power consumption of your device and the sunshine duration of your area from weather bureau for a proper PV Improper PV could shorten the battery life or provide insufficient power to BSP 300 Step 4 Connect 8023af 802 3at PoE Device 1 Connect the PoE devices to Port 1 Port 2 of the BSP 300 2 Check the PoE In Use LED if the network devices such as PoE Camera PoE Wireless AP is powered the PoE In Use LED will turns ON and Link Act LED will turns on or blinking for a success connection or data receiving Please use Cat 5 5e or above cable and the maximum distance should within 100 meters If the Network devices are installed outdoor please consider to install a lightening arrestor to protect the network device and BSP 300 Step 5 Connect other device Ethernet Extender 1 Connect any other network device to Port 3 of BSP 300 2 If there is device require DC power connect the pin 3 pin 4 of the terminal block from BSP 300 directly The maximum DC out from BSP 300 is 24VDC 2A The
Download Pdf Manuals
Related Search