User Manual
Contents
1. Store all detergents and additives in a safe place away from the reach of the children 3 Installation Refer to the nearest Authorised Service Agent for installation of your product To make the product ready for use make sure that the electricity tap water supply and water drainage systems are appropriate before calling the Authorised Service Agent If they are not call a qualified technician and plumber to have any necessary arrangements carried out G Preparation of the location and electrical tap water and waste water installations at the place of installation is under customer s responsibility Installation and electrical connections must be carried out by the Authorised Service Agent Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons Prior to installation visually check if the product has any defects on it If so do not have it installed Damaged products cause risks for your safety Make sure that the water inlet and discharge hoses are not folded pinched or crushed while pushing the product into its place after installation or cleaning procedures When placing the product pay attention not to damage the floor walls piping etc Do not hold the product from its door or panel to move it 7 Appropriate installation location Place the product on a solid and flat floor that has sufficient load carrying Capacity The produc2. S Please check the salt indicator on the display to see whether there Is adequate amount of softening salt 35 in the dishwasher or not You need to refill the salt reservoir with salt whenever Salt warning indicator appears on the display of your machine GJ Adjusting the water hardness level is explained in Water Softening System section Rinse Aid indicator gt Please check the rinse aid indicator on the display to see whether there is adequate amount of rinse aid in the dishwasher or not You need to refill the rinse aid reservoir with rinse aid whenever rinse aid warning Indicator appears on the display of your machine End of programme End of Programme indicator will light up once the washing programme Is over 1 Press the On Off button to turn off your machine 2 Close the tap Unplug the machine from the socket GJ For energy saving the product is automatically turned off following the completion of the programme or if the programme is not started GJ Leave your dishes in the machine for about 15 minutes to cool down after they are washed Your dishes will dry ina shorter time if you leave the door of your machine ajar during this period This process will increase the drying effectiveness of your machine EN 6 Maintenance and cleaning Service life of the product extends and frequently faced problems decrease if it is cleaned at regular intervals A Unplug the product and t
3. SulyOeW AEM 1S9 SEJ y Ul p aueajo y u BunieA 1d y q IIIA eu pouesjo aid JO aie Hurem 1d y ase yey s usip SOYSIP p lios y UO s jueuuu i p deuo5s de zey s usip jep p jos uunip uu y YOIUM sued pue sjod saysip y S S pue s ys p y JO uunip uu y 104 wesBosd y BUIAOWS 104 jqeynsS p lios Ay Jo jqe ins ye weiGHoid Buiysem Aeq p lios AjiAeey 104 jqeyng f 16 p uos ay s ouluuu9 j q BHulysem eS uuouoo5 Ison E O ous SSS qe ulttuueiBoid Builios jo 316 q 31 EN Auxiliary functions Washing programmes of your dishwasher are designed to obtain the best cleaning effect considering the type of the soil soiling degree andproperties of the dishes to be washed Auxiliary functions are provided in order to enable you to save time water and energy and to perform a more comfortable washing with conditions specific to you G Auxiliary functions may cause changes in the programme duration G Auxiliary functions are not Suitable for all washing programs Indicator of the auxiliary function that is not compatible with the programme will not be active To add auxiliary function to the programme 1 Select the desired washing programme by pressing the programme selection key 2 Inthe selected washing programme if auxiliary function is selected its symbol will be displayed on the screen If the function button is pressed again the symbol will
4. and descaled Otherwise ions that create the hardness will accumulate on the surfaces of the dishes and may adversely affect the washing Shining and drying performances of the product The product is equipped with a water softening system which reduces the hardness of incoming water This system softens the supply water that enters into the product to a level that will allow washing the dishes with the required quality Adjusting the water softening system Washing performance will increase when water softening system is adjusted properly Use the test stripe Supplied with the product to determine the supply water hardness in order to adjust the system 11 EN Adding salt Water softening system needs to be regenerated in order for the product operates with the same performance continuously Dishwasher salt is used for this purpose GJ Use in your product only the special softening salts produced particularly for use in dishwashers GJ We recommend using granular or powder softening salts Do not use Salts containing insoluble substances such as table salt or common Salt in the machine Performance of water softening system may deteriorate in time GJ Salt reservoir will fill with water when you Start the product Therefore add the softening salt before starting the machine 1 First take the lower basket out to add softening Salt 2 Turn the salt reservoir lid in counter clockwise to open it A B G
5. disappear and selection is cancelled 3 Selection will be cancelled when you press the function key again Half Load Function It is used to operate the machine without loading it completely 1 Load your dishes in the machine as you like 2 Press the On Off key 3 Select the desired programme and press the Half Load key Half Load indicator will appear on the display 4 Press Start Pause Cancel key to Start the programme GJ With the Half Load function you can save both water and power while using the lower and upper baskets of the machine Fast Function It shortens the time of the washing cycle selected and decreases water consumption by enabling washing under higher pressure SteamGloss function It provides superior drying performance EN Automatic Detergent Detection Feature The product has a feature to automatically detect the type of the detergent and adjust the washing programme and drying system to the best performance If special tablet detergent is used the programme duration can be extended by 20 minutes in order to optimize the washing and drying performance To deactivate 1 After turning on the machine press Time Delay and P keys Simultaneously Continue to press until the countdown 3 2 1 is completed on the display 2 Press P key to activate the a position In a 0 position automatic detergent detection feature is disabled and active in a 1 position S
6. door of the dishwasher Programme selection 1 Press the On Off button to turn on your machine 2 Refer to the table of Programme data and average consumption values to determine a washing programme suitable for your dishes 3 Press Programme Selection keys until the number of the programme you Selected appears on the Programme indicator Use P to switch to the next programme and P to switch to the previous one EN uliuue1Boid 1s 1 94 Buisn pue IIoA19s9 1 ple SSULJ N e pue sasu dS p jes 1 u ljJos 1 eA inj e UYA JNO paleo q JSNW ZrZ0S NJ YM S9uepio22e ul S8 BY s lninsui Hulse 10 ultuue1Boid 5u 1lJ J l suollipuo2 jeonoesd Japun 1n290 31049194 ACW s Su J Jjiq suo nipuo5 piepue s JOPUN PSUILUS Ep J A qe y u UMOUS SEN eA uodwnsuos By pug pug SUIY JOH sul p oO Aq sulY JOH sull pl oO yseMm Kiq asuly OH suu Plog ysem USEA 91d 002 01 Buljlos jo yunowe y o pejsnipe s ou nb s wweposd y sul JOH sul p oO yseMm USEA 91d uiw uoljeing suondo noulim Su nb s uuul i1Boid ySem ld yseM a a s ed G q WD G L W39 GZ V a V a v s uab19 0q s usip Jo sed Je 104 BIQeEyINS Ajjeonewojne uun Bulysem y se A se Jayem Bulysem y JO BunieA 1d y junowe pue i1nle1 duu ae yeu s ys p Ajlep p jios dnpjing sopo peq ay Bunu A 4d 104 snu pue sAep ma e JO
7. indicator 12 End of Programme indicator 29 EN Keys On Off key It is used to turn on or off the machine Press On Off Key to switch ON A Signal is heard and the machine door is turned on Press the On Off key for 1 second to turn off A signal will be heard and machine will turn off at the end of 1 second To turn off while the programme is running keep Off key pressed for 3 seconds A countdown in the form of 3 2 1 will appear on the display Machine will turn off with the end melody at the end of 3 seconds Machine will turn on with economy programme in On mode and the number of the economy programme will appear on the programme indicator In Of position indicators on the display will turn off Start Pause Cancel key It is used to start pause or cancel a selected programme or function Program Selection keys They are used to select the washing programme you determined from the table of Programme data and average consumption values Delayed Start key It should be pressed to make the time delay settings Preparing the machine 1 Open the door of the dishwasher 2 Place the dishes in accordance with the instructions in the user manual 3 Make sure that the upper and lower impellers rotate freely 4 Put adequate amount of detergent into the detergent dispenser 30 5 Check if the Salt and Rinse Aid indicators light and add salt and or rinse aid if needed 6 Close the
8. 00 W consumption Total current depends on the model Po GS Pears Drain pump power 30 W Water pressure 0 3 10 bar 3 100 N cm 0 03 1 0 Mpa G Technical specifications may be changed without prior notice to improve the quality of the product GJ Figures in this manual are schematic and may not match the product exactly GJ Values stated on the product labels or in the documentation accompanying it are obtained in laboratory conditions in accordance with the relevant Standards Depending on operational and environmental conditions of the product these values may vary Note for test institutions Data required for performance tests shall be provided upon request Requests can be e mailed to the following address dishwasher standardloading com Do not forget to provide the code stock and serial numbers of the product to be tested in your request e mail along with your contact information Code stock and serial numbers of the product is located on the type label attached to the side of the door 4 EN 2 Important safety instructions This section contains safety instructions that will help to get protected from risk of personal injury or property damage Fallure to follow these instructions Shallvoid e all warranties General safety e Never place the product Onacarpet covered floor e otherwise lack of airflow beneath the product will cause electrical parts to overheat T
9. 1 Press the Time Delay function key after selecting the washing programme and other auxiliary functions 2 Once you press the Time Delay key Display Information Line will show 0 30 and Time Delay indicator will start flashing Set the desired time by pressing the Time Delay key Time will increase with increments of 30 EN minutes up to 6 hours and after that will appear on the Display Information in 1 hour increments up to 24 hours every time you press the key 4 Press Start Pause Cancel key to start countdown for the Time Delay Time Delay indicator and Start Pause indicator will light continuously until the end of the period Time Delay is displayed on the Display Information Line Selected programme will start as soon as the countdown Is over Changing the settings while Time Delay function is enabled While the Time Delay function is activated you cannot make changes in the washing programme auxiliary functions or the duration of delay time GJ Programme and auxiliary functions cannot be set changed after the programme has Started To cancel the Time Delay function 1 Press and hold Start Pause Cancel key for 3 seconds 2 When the Start Pause Cancel key is pressed and hold 3 2 1 appear on the Display Information Line Time Delay indicator will turn off at the end of the cancellation process and delaying process is cancelled GJ You can select and start anew programme follow
10. A i ii P miba k 1 z di MY AS ELA ALS N oN N Msg I Roll N A H ar ri v SAIL SSIS Sa Ya I 7 be all X 38 EN Troubleshooting Machine does not start Power cable is unplugged gt gt gt Check if the power cable is plugged in Fuse is blown gt gt gt Check the fuses in your house Water is cut gt gt gt Make sure that the water inlet tap is open Door of the machine is open gt gt gt Make sure that you have closed the door of the machine On Off button is not pressed gt gt gt Make sure that you have turned on the machine by pressing the On Off button Dishes are not washed clean Dishes are not placed orderly in the machine gt gt gt Load the dishes as desc ribed in the user manual Selected programme is unsuitable gt gt gt Select a programme with a higher temperature and cycle time Impellers are stuck gt gt gt Prior to starting the programme turn the lower and upper impellers by hand to make sure that they rotate freely Impeller holes are clogged gt gt gt Lower and upper impeller holes might be clogged with food remnants such as lemon pips Clean the impellers regu larly as illustrated in section Cleaning and Care Filters are clogged gt gt gt Check if the filter system is clean Clean the filter system regularly as illustrated in section Cleaning and Care Filters are installed incorrect
11. Aquasafe system against water leaks that may occur at hose inlet Water contact with the valve box of the system must be prevented Otherwise electrical assembly will get damaged If the Aquasafe system is damaged unplug the product and call the Authorised Service Agent Asthe hose set contains electrical connections and assemblies never shorten or lengthen the hose with extension hoses Electrical connection Connect the product to a grounded outlet protected by a fuse complying with the values in the Technical specifications table Manufacturer Shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations 9 Connection must comply with national regulations Power cable plug must be within easy reach after installation Unplug the product after the washing programme Is over The voltage and allowed fuse or breaker protection are specified in the Technical specifications section If the current value of the fuse or breaker in the house is less than 16 Amps havea qualified electrician install a 16 Amp fuse The specified voltage must be equal to your mains voltage Do not make connections via extension cables or multi plugs Damaged power cables must be replaced by the Authorised Service Agent If the product has a failure it Should not be operated unless it is repaired by the Authorised Service A
12. Before initial use fill the water softening system with 1 litre of water C 3 Fillthe salt reservoir with salt by using salt funnel D To speed up dissolution rate of salt in water Stir it with a spoon GJ You can put about 2 kg of softening salt into the salt reservoir 4 Replace the lid and tighten it securely when the reservoir is full 5 If you will not start a washing programme immediately after adding the salt run the machine empty in the shortest programme to dissolve and wash away the scattered Salt in the machine G Since different salt brands in the market have different particle sizes and since the water hardness may vary dissolution of the salt in water may take a couple of hours Therefore Salt Indicator remains on for a while after adding salt into the machine Detergent You can use powder or tablet detergent in the machine G Only use in the machine the detergents produced particularly for use with dishwashers We recommend you not to use detergents that contain chlorine and phosphate as they are harmful for the environment GJ Contact the detergent producer if the dishes are wet and or if you notice limescale spots particularly on glasses after the washing programme is over Adding detergent G Refer to the Programme Table to determine the correct amount of detergent for the selected programme A Donot put solvents into the detergent dispenser There Is the risk of e
13. basket height adjustment mechanism are at the same level down or up To lower the basket 1 Press the latch on the basket adjustment mechanism right or left to lower the basket B 2 Repeat the same process to lower the other side of the basket 3 Make sure that both sides of the basket height adjustment mechanism are at the same level down or up P lt gt lt Q S ND KA gt ee Ke gt SH z AUN H Q 2 EN Adjusting the height of empty upper basket depends on the model You can adjustthe height of the upper basket according to the size of the dish to be washed Use basket rollers to change the basket height 1 Turn the stoppers on the ends of the upper basket rails by turning them aside A 2 Take the basket out B 3 Change the position of the rollers place the basketinto the rail and close the stoppers C s ay APS J INY ye YA VA WSS eas SAS ASSIA 4 si B WE AAH as SS sf NANA ANG E KY 28 EN 5 Operating the product 2 6 3 1 Display a Half Load Function 2 On Off key b Fast Function 3 Start Pause Cancel key c SteamGloss function 4 Time Delay key d Turbo Wash Function 5 Function keys 6 Program Selection keys 7 Programme indicator 13 Screen information line 8 Salt S indicator 14 Child Lock indicator 9 Notin use 15 Rinse aid indicator 10 Start P Pause I indicator 16 Not in use 11 Time Delay
14. e lower basket of the machine are designed for an easier placement of large pieces such as pans bowls etc 1 2 You can create larger spaces by folding each wire individually or all of them at once Lay the foldable wires down by pressing on the latch A Collapsible lower basket wires 4 pieces depends on the model The four piece foldable wires located at the lower basket of the machine are designed for an easier placement of large pieces such as pans bowls etc 1 2 3 4 You can create larger spaces by folding each wire individually or all of them at once Lay the foldable wires down by pressing on the latch A 19 EN Collapsible lower basket wires 6 pieces depends on the model The foldable wires A located at the lower basket of the machine are designed for an easier placement of large pieces such as pans bowls etc You can create larger spaces by folding each wire individually or all them at once To bring the collapsible wires into horizontal position grab the wire from mid position and push them in the directions of arrows B To bring the wires back to vertical position just lift them up Collapsible wires will click into the latch again Gi Bringing the wires to the horizontal position byholding them from the tips may cause them to bend Therefore it will be appropriate to bring the wires In the middle to horizontal or vertical position by holding them from their stems a
15. e same process in reverse order to open the racks To adjust the height of the racks 1 Fold the rack E 2 Slide the rack up F 3 Open the rack at the desired level G Make sure that the impeller does j PH TANAY SRY not touch the dishes you placed D Z gt i Bp onthe racks Lower basket bottle wire Upper basket drawer depends on the model depends on the model The bottle wire is designed for easier You can easily place additional desert washing of long pieces with wide spoons small forks and knives into mouths You may take out the bottle the basket drawer installed to the wire from the basket when not in use upper basket of your machine by pulling it out from both sides H Sy Aa iiil s X gt Upper basket height adjustable rack depends on the model Use the lower and upper parts of the height adjustable racks in the upper basket of the machine by sliding them down or up according to the heights of the glasses cups or etc A B C 23 EN Upper basket glass support piece depends on the model When placing long stemmed glasses or wine glasses do not lean them against other pieces but to the edge of the basket or to the rack 1 Do not lean long glasses against each other They can move and get damaged during washing If you wish to place large volume pieces on the upper basket release the tab of the glass support piece from the upper basket wire it is
16. ecial purpose washing chemicals such as glass and stainless Steel protectors GJ Tablet detergents give satisfying results only under certain usage conditions The best washing performance in dishwashers is obtained by using detergent rinse aid and water softening salt individually 14 GJ Information about suitable places detergent dispenser basket etc in the dishwasher to place the tablet can be found amongst the usage instructions on the packages of the tablet detergents Tablet detergent types commonly found in the market 2in1 Contains detergent rinse aid or water softening salt 3in1 Contains detergent rinse aid and water softening salt 4in1 Contains glass protectors in addition to detergent rinse aid and water softening salt 5in1 Contains glass and stainless Steel protectors in addition to detergent rinse aid and water softening Salt G Observe the instructions of the detergent manufacturer on the package when using tablet detergents When you switch to powder detergent from tablet detergent 1 Make sure that salt and rinse aid reservoirs are full 2 Set the water hardness to the highest level and perform an empty run 3 After the empty washing cycle review the user manual and readjust the water hardness level so as to Suit the water supply 4 Make the appropriate rinse aid settings GJ Depending on the model salt indicator and or rinse aid indicator must be enabled again if they w
17. ends on the model Basket adjustment mechanism on the upper basket of the machine is designed to allow you create wider areas in the upper or lover section of the machine based on your requirements by adjusting the height of the loaded basket in up or down directions without removing it from the machine To raise the basket 1 Grab one of the upper basket wires right or left and lift it up A 2 Repeat the same process to raise the other side of the basket 3 Make sure that both sides of the basket height adjustment mechanism are at the same level down or up To lower the basket 1 Press the latch on the basket adjustment mechanism right or left to lower the basket B 2 Repeat the same process to lower the other side of the basket 3 Make sure that both sides of the basket height adjustment mechanism are at the same level down or up 26 EN Adjusting the height of loadedupper basket depends on the model Basket adjustment mechanism on the upper basket of the machine is designed to allow you create wider areas in the upper or lover section of the machine based on your requirements by adjusting the height of the loaded basket in up or down directions without removing it from the machine To raise the basket 1 Grab one of the upper basket wires right or left and lift it up A 2 Repeat the same process to raise the other side of the basket 3 Make sure that both sides of the
18. ere disabled before EN Rinse aid G Therinse aid used in dishwashers IS a Special combination used to increase drying efficiency and prevent water or limescale stains on the washed Items For this reason care must be paid to have rinse aid in the rinse aid reservoir 4 Turn the rinse aid amount adjuster manually to a position between 1 and 6 4 If there are Stains on tableware items after washing level must be increased and if there is a blue trace after wiping them by hand it must be decreased This is set to position 4 and to use rinse aids produced specially for dishwashers only Check Rinse Aid Indicator to determine whether It is necessary to add rinse aid or not 3 depends on the model Having a dark light on the indicator shows that there is Sufficient amount of rinse aid in the dispenser If the colour of the indicator is light add rinse aid 1 Open the lid of the rinse aid as factory default reservoir by pressing its latch B Fill the reservoir until MAX level Close the lid of the reservoir by pressing on it lightly Wipe clean any spilled rinse aid outside the reservoir Rinse aid that spilled accidentally will cause foaming and it will eventually decrease washing performance 15 Items not suitable for washing in the dishwasher e Never wash dishes soiled by cigarette ash candle remnants polish dyestuff chemicals etc in your dishwasher e Donot wash iron alloy i
19. et the desired location by pressing the Time Delay key 3 Turn off the machine with On Off button to save the changes Interior Lighting Depends on the model Some models have interior lighting to illuminate the interior when the door IS opened Changing the interior lighting setting 1 After turning on the machine press Time Delay and P keys Simultaneously Continue to press until the countdown 3 2 11s completed on the display 2 Press P key to activate the L position At L 0 position the interior lighting is turned off and turned on in L 1 position Set the 33 desired location with the Time Delay key 3 Turn off the machine with On Off button to save the changes Changing Warning Sound Volume Your machine is equipped with an audio signal to inform warnings audibly 1 After turning on the machine press Time Delay and P keys Simultaneously Continue to press until the countdown 3 2 1 is completed on the display 2 Press P key to activate the S position 3 Select one of S1 S2 and SO with Time Delay key 4 Turn off the machine with On Off button to save the changes Programming the washing time Time Delay If an economical electricity tariff is applied in your region you can use the Time Delay function to wash your dishes during appropriate hours You can delay the start of the selected program until 24 hours Time Delay cannot be set after the programme Starts
20. gent There is the risk of electric shock Initial use Before starting to use the product make sure that all preparations are made in accordance with the instructions in sections Important Safety instructions and Installation EN To prepare the product to do the dishes perform first operation in the shortest programme with detergent while the machine is empty During the initial use fill the salt reservoir with 1 litre of water prior to filling it with salt Some water might have remained in the product due to the quality control processes in the production It is not harmful for the product Disposing of packaging material Packaging materials are dangerous to children Keep packaging materials in a Safe place away from reach of the children Package information Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations Do not dispose of the packaging materials together with the domestic or other wastes Take them to the packaging material collection points designated by the local authorities Transportation of the product A If you need to move the product do it in upright position and hold from the rear side Slanting the product onto its front side may cause the electronic parts in it get wet and damaged 1 Unplug the product before transporting it 2 Remove water drainage and water supply connections 3 Drai
21. h EN 5 Replace the metal plastic filter 6 Place the coarse filter into the microfilter Make sure that it is properly seated Turn the coarse filter clockwise until a click sound is heard Z Donotuse the dishwasher without filter G Incorrect placement of the filters will reduce washing efficiency Cleaning the hose filter Cleaning the impellers Clean the impellers at least once a week in order for the machine operates efficiently Lower impeller Check if the holes on the lower impeller 1 are clogged If they are clogged remove and clean the impeller Pull the lower impeller up to remove it A B Damages on the machine that may be caused by impurities coming from the urban supply water or your own water installation such as sand dirt rust etc can be prevented by means of the filter attached to the water inlet hose Check the filter and the hose regularly and clean them if necessary 1 Turnoff the tap and remove the hose 2 After taking out the filter clean it under running tap water 3 Place the cleaned filter back to its Seat in the hose 4 Install the hose to tap depends on the model 37 EN Upper impeller Check if the holes on the upper impeller 2 are clogged If they are clogged remove and clean the impeller Turn its nut to left to remove the upper impeller C D Make sure that the nut Is tightened well when installing the upper
22. he water pressure exceeds 10 bars a pressure relief valve should be installed in between Use a screw on hose connector to connect the water inlet hose to a water tap with a inch external thread If required use a filter insert to filter deposits from the pipes 3 4 E 10 s T e Open the taps completely after making the connections to check for water leaks For your safety close the water inlet tap completely after the washing programme is over 8 Connection to the drain Water discharge hose can directly be connected to the drain hole or sink s drainage The length of this connection must be min 50 cm and max 100 cm from the floor 10 20 30 40 50 60 70 80 9 100 110 0 A discharge hose longer than 4 meters causes dirty washing Attach the water discharge hose to the drainpipe without bending it Tightly fix the water discharge hose to the drainpipe in order to prevent any dislocation of the water discharge hose during operation of the product GJ Drainpipe must be connected to the sewage system and it should not be connected to any surface water EN Adjusting the feet If the door of the product cannot be closed properly or if the product swings when you push it slightly then you need to adjust the feet of the product Adjust the feet of the product as illustrated in the installation manual supplied with the product Aquasafet depends on the model Protect the
23. his will cause problems with your e product e Donot operate the product if the power cable plug is damaged Call the Authorised Service Agent e Connect the product to a grounded outlet protected by a fuse complying with the values in the Technical specifications table Do not neglect to have the grounding installation made by a qualified electrician Manufacturer Shall not be liable for any damages that will arise when the productisused e without grounding in accordance with the local regulations e The water supply and 5 EN draining hoses must be securely fastened and remain undamaged Unplug the product when notin use Never wash the product by spreading or pouring water onto it There is the risk of electric shock Never touch the plug with wet hands Never unplug by pulling on the cable always pull out by grabbing the plug The product must be unplugged during installation maintenance cleaning and repairing procedures Always have the installation and repairing procedures carried out by the Authorised Service Agent Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorised persons Never use chemical solvents in the product They bring forth risk of explosion When you pull the upper and lower baskets out completely the door of the product will bear all the weight of the baskets Do not put other loads on the door othe
24. hooked to Thus you can obtain a wider space pon a rth fo ESAS Prwrewaills SRST Collapsible upper basket wires depends on the model To bring the collapsable wires on the upper basket of the machine into horizontal position press on the latch 1 Place your larger dishes into the area created 2 To bring the wires back to vertical position just lift them up Collapsible upper basket wires depends on the model There are collapsible wires on the upper basket of the machine that you can lay down when you need a larger room for big dishes On your upper basket there are two types of collapsible wires namely fully laid system A and gradually laid system B To bring the collapsible wires into horizontal position push the wires in the direction of the arrow by holding them from the middle You can place your larger dishes into the area created To bring the wires back to vertical position just lift them up Collapsible wires will click into the latch again Gi Holding the wires from ends to put them in lying position may cause the wires to bend For this reason It will be appropriate to hold the wires in the middle from their bottoms and to push in the direciton of the arrow to lay down or bring them to vertical position wed LT g gt 8 Vili m q Es q ks SN 25 EN Adjusting the height of loadedupper basket dep
25. ing the cancellation of Time Delay function GJ Time Delay function can not be set after the programme starts Starting the programme To start your machine after selecting the programme and auxiliary functions press Start Pause Cancel key Once the programme Starts a tune is played and the estimated time remained to the end of the programme 34 Line Start Pause Cancel indicator Starts lighting continuously G Your machine performs water softening depending on the hardness level of the supply water Remaining time displayed towards the end in some programmes can be different from the time indicated at the beginning due to this process The total time can also change while the programme is running depending on the ambient temperature where your machine is installed temperature of the supply water and amount of the dishes G Pay attention not to open the door of the machine when it is running Stop the machine by pressing Start Pause Cancel key if you have to open the door Then open the door of the machine There may bea rush of vapour when you open the door of your machine be careful Close the door of your machine and press Start Pause Cancel key again Programme will resume running G The machine will remain silent in pause mode for some time in order to remove the water in the machine and on the dishes completely and to have the water softener cleaned and then it will resume running in drying m
26. ive detergents that are commercially available Foam forms in the machine e Dishes are washed with hand wash detergent by hand but not rinsed be fore placing them into the machine gt gt gt Hand wash detergents do not contain antifoam There is no need to hand wash the dishes before pla cing them into the machine Removing the coarse soil on the dishes under tap water with a tissue paper or fork will be sufficient e Rinse aid has spilled into the machine when adding rinse aid gt gt gt Take care that rinse aid is not spilled in the machine when you are filling it Clean any spilled rinse ait with the help of a tissue paper towel e Lidoftherinse aid reservoir is left open gt gt gt Make sure that the lid of the rinse aid reservoir is closed after adding rinse aid Kitchen utensils are broken e Dishes are not placed orderly in the machine gt gt gt Load the dishes as desc ribed in the user manual e Baskets are overloaded gt gt gt Donot overload the baskets in excess of their capacity Water remains in the dishwasher at the end of the programme e Filters are clogged gt gt gt Check if the filter system is clean Clean the filter system regularly as illustrated in section Cleaning and Care e Discharge hose is clogged blocked gt gt gt Check the discharge hose If ne cessary remove the discharge hose clear the blockage and insert Is as illustrated in the user manual GJ Ifyou cannot eli
27. ly gt gt gt Check the filter system and make sure that it is installed correctly Baskets are overloaded gt gt gt Do not overload the baskets in excess of their capacity Detergent is stored under unsuitable conditions gt gt gt If you are using powder detergent do not store the detergent package in humid places Keep it ina closed container if possible For ease of storing we recom mend you to use tablet detergents Detergent is not sufficient gt gt gt If you are using powder detergent adjust the amount of detergent according to the soiling degree of your dishes and or programme definitions We recommend you to use tablet deter gents for optimum results Rinse aid is not sufficient gt gt gt Check the rinse aid indicator and add rinse aid if necessary Increase the rinse aid setting if there is enough amount of rinse aid in the machine Detergent dispenser lid is left open gt gt gt Make sure that the detergent dispenser lid is closed tightly after adding detergent 39 EN Dishes are not dry at the end of cycle Dishes are not placed orderly in the machine gt gt gt Place your dishes ina way that no water will accumulate in them Rinse aid is not sufficient gt gt gt Check the rinse aid indicator and add rinse gid if necessary Increase the rinse aid setting if there is enough amount of rinse aid in the machine Machine is unloaded right after the programme is over gt gt gt Do n
28. materials together with the domestic or other wastes Take them to the packaging material collection points designated by the local authorities This product was manufactured using the latest technology in environmentally friendly conditions CONTENTS 1 Dishwasher 3 Technical specifications 4 2 Important safety instructions 5 General safety Intended use Children s safety 3 Installation Appropriate installation location Connecting water supply Connection to the drain Adjusting the feet Aquasafe Initial use Disposing of packaging material Transportation of the product Compliance with the WEEE Directive and Disposing of the Waste O O O O O OO xl N ODM m Product 10 Compliance with RoHS Directive 10 4 Prewashing 11 Tips for energy saving 11 Water softening system 11 Adjusting the water softening system 11 Adding salt 12 Detergent 13 Adding detergent 13 Tablet detergents 14 Rinse aid 15 Silverware basket 18 Silverware basket piece 18 Movable silverware basket 18 Collapsible lower basket wires 2 pieces 19 Collapsible lower basket wires 4 pieces 19 Collapsible lower basket wires 6 pieces 20 Collapsible lower basket wires 4 amp 8 pieces 21 Lower basket multipurpose height adjustable service rack 22 Lower basket bottle wire 23 Upper basket height adjustablerack 23 Upper basket drawer 23 Upper basket glass support piece 24 Collapsible upper basket wi
29. minate the problem although you follow the instructions in this section consult your dealer or the Authorised Service Agent Never try to repair a nonfunctional product yourself 44 EN 150039 0100_AA_ EN www beko com
30. n the remaining water in the product completely Compliance with the WEEE Directive and Disposing of the Waste Product x This product complies with EU WEEE Directive 2012 19 EU This product bears a E Classification symbol for waste electrical and electronic equipment WEEE This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling Do not dispose of the 10 waste product with normal domestic and other wastes at the end of its service life Take it to the collection center for the recycling of electrical and electronic equipment Please consult your local authorities to learn about these collection centers Compliance with RoHS Directive The product you have purchased complies with EU RoHS Directive 2011 65 EU It does not contain harmful and prohibited materials specified in the Directive EN 4 Prewashing Tips for energy saving Following information will help you use the product in an ecological and energy efficient manner e Wipe away any coarse food remnants on the dishes before putting them in the product e Operate the product after filling it completely e When selecting a programme refer to the Programme Table e Donotput more detergent than Suggested on the detergent package Water softening system G The dishwasher requires soft water If the hardness of the water Is above 6 dH the water must be softened
31. nd pishing in the direction of arrow 20 EN Collapsible lower basket wires 4 amp 8 pieces depends on the model The foldable wires A located at the lower basket of the machine are designed for an easier placement of large pieces such as pans bowls etc You can create larger spaces by folding each wire individually or all SLB i them at once US saci To bring the collapsible wires into NOA Ei horizontal position grab the wire from mid position and push them in the directions of arrows B To bring the wires back to vertical position just lift them up Collapsible wires will click into the latch again C i Bringing the wires to the horizontal position byholding them from the tips may cause them to bend Therefore it will be appropriate to bring the wires in the middle to horizontal or vertical position by holding them from their stems and pishing in the direction of arrow y RI DA A S j N Q BIN Ve Si EL US ri ful rs B i 21 EN Lower basket multipurpose height adjustable service rack depends on the model This accessory located at the lower basket of the machine allows you to easily wash pieces such as extra glasses long ladles and bread knives To close the racks 1 Fold the rack A 2 Slide the rack up B 3 Put the rack in vertical position C 4 Slide the rack down and lock it x T HH with the tabs D KA VAA AH CG Perform th
32. ode Child Key Lock You may prevent other people from interrupting and changing the programme cycle and time delay while the machine Is running To activate the Child Lock 1 Pres Child Key Lock keys simultaneously and hold for 3 seconds 2 3 2 L is displayed on Display EN Information Line and key lock is activated GJ Child Lock prevents the selected programme or functions from being changed and disables the Start Pause Cancel key G Child Lock does not lock the door of the machine GJ Ifyou turn your machine off by using On Off key at the end of the programme the Child Lock will be deactivated automatically GJ For energy saving the product is automatically turned off following the completion of the programme or if the programme is not started To deactivate the Child Lock 1 Pres Child Key Lock keys Simultaneously and hold for 3 seconds 2 3 2 1L is displayed on Display Information Line and key lock is cancelled Cancelling the programme 1 Press Start Pause Cancel key for 3 seconds to cancel the programme 2 Release the key when the Start Pause indicator starts flashing For acouple of minutes the machine will fulfill the necessary operations required to cancel the programme There might be residues of detergent or rinse aid left in the machine and or on the pieces being washed depending on the Step the programme you have cancelled was in Salt indicator
33. oeko m Dishwasher Instruction Manual Please read this user manual first Dear Customer We hope that you get the best results from the product which has been manufactured in state of the art plants and passed through a strict quality control procedure Therefore please read the entire user manual carefully before using the product and keep it as areference for future use In case of transferring the product to someone else give the manual as well The user manual will help you use your product in a fast and safe way e Read the user manual before installing and starting your product e Always follow the safety instructions e Keep this user manual within easy reach for future reference e Read also the other documents supplied with the product Remember that this user manual is alSo applicable for several other models Differences between models will be identified in the manual Explanation of symbols Throughout this User Manual the following symbols are used Important information or useful hints about usage Warning for hazardous situations with regard to life and property Warning for electric shock Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations 0 A A Do not dispose of the packaging materials together with the domestic or other wastes Take them to the packaging material collection points designated b
34. ogramme There is a different odour in the machine GJ Anew machine has a peculiar odour It will fade out after a couple of was hing e Filters are clogged gt gt gt Check if the filter system is clean Clean the filter system regularly as illustrated in section Cleaning and Care e Dirty dishes are kept in dishwasher for 2 3 days gt gt gt If you are not going to start the machine right after you have put the dishes into it remove the remnants on the dishes and run the Prewash programme without de tergent every 2 days In such cases do not close the door of the machine completely in order to avoid odour build up in machine You can also use commercially available odour removers or machine cleaners 41 EN Rust discoloration or surface deterioration occurs on dishes Salt leakage exists gt gt gt Salt may cause deterioration and oxidation on metal surfaces Pay attention not to spill salt around the salt filling hole while adding salt Make sure that the salt reservoir lid is tightly closed after finishing the filling process Run the prewash programme to remove the salt that spilled inside the machine Since the salt granules that will remain under the lid will dissolve during prewash causing the lid loosen check the lid once again at the end of the programme Salty food remnants have remained on dishes for along time gt gt gt If sil verware soiled with such foods will be kept waiting in machine dirt must be
35. ot unload your machine right after washing process is completed Slightly open the door and wait for evacuation of the steam inside for a while Unload the dishes after the pieces cool down to a touchable level Start unloading process from the lower basket Thus dropping of water remained ona piece at upper basket onto the pieces at lower basket is prevented Selected programme is unsuitable gt gt gt Since rinsing temperature is low at programmes with short duration drying performance will also be low Select programmes with longer duration for a higher drying performance Surface quality of the kitchen utensils is deteriorated gt gt gt Desired was hing performance can not be obtained at kitchen utensils with deteriora ted surfaces and it is not suitable to use such utensils in terms of hygiene as well Also water can not flow easily on deteriorated surfaces It is not recommended to wash such kitchen utensils in dishwasher It is normal that drying complaints can be experienced with Teflon kitchen utensils It is associated with the structure of Teflon Since the surface tensions of Teflon and water are different water droplets will remain as beads on the Teflon surface Tea cafe or lipstick stains remain on dishes Selected programme is unsuitable gt gt gt Selecta programme with a higher temperature and cycle time Surface quality of the kitchen utensils is deteriorated gt gt gt Tea and cafe stains or othe
36. prior to filling it with detergent Detergent is added long before the washing process gt gt gt Pay attention to add detergent shortly before start up of the washing Opening of the detergent dispenser lid is prevented during washing gt gt gt Place the dishes in a way that will not prevent the detergent dispenser lid from opening and the water going into the machine from impellers Detergent is stored under unsuitable conditions gt gt gt If you are using powder detergent do not store the detergent package in humid places Keep it in a closed container if possible For ease of storing we recom mend you to use tablet detergents Impeller holes are clogged gt gt gt Lower and upper impeller holes might be clogged with food remnants such as lemon pips Clean the impellers regu larly as illustrated in section Cleaning and Care Decorations and ornaments on kitchen utensils are being erased GJ Decorated glasses and decorated luster porcelains are not suitable for washing in the dishwasher Manufacturers of glassware and porcelain tableware items do not recommend washing such kitchen utensils in the dishwashers either Dishes are scratched G Kitchen utensils that contains or are made of aluminum should not be was hed in dishwasher Salt leakage exists gt gt gt Pay attention not to spill salt around the salt filling hole while adding salt Spilled salt can cause scratches Make sure that the salt reser
37. r dye spots may not be cleaned in dishwasher when they have penetrated in deteriorated surfaces Desired washing performance can not be obtained at kitchen utensils with deteriorated surfaces and it is not suitable to use such utensils in terms of hygiene as well It is not re commended to wash such kitchen utensils in dishwasher Detergent is stored under unsuitable conditions gt gt gt If you are using powder detergent do not store the detergent package in humid places Keep it in a closed container if possible For ease of storing we recom mend you to use tablet detergents 40 EN Lime traces remain on dishes and glassware gains a misty appearance e Rinseaidisnotsufficient gt gt gt Check the rinse aid indicator and add rinse aid if necessary Increase the rinse aid setting if there is enough amount of rinse aid in the machine e Water hardness setting is low or salt level is insufficient gt gt gt Measure the hardness of the supply water appropriately and check the water hardness setting e Salt leakage exists gt gt gt Pay attention not to spill salt around the salt fil ling hole while adding salt Make sure that the salt reservoir lid is tightly closed after finishing the filling process Run the prewash programme to remove the salt that spilled inside the machine Since the salt granules that will remain under the lid will dissolve during prewash causing the lid loosen check the lid once again at the end of the pr
38. removed by prewash or dishes must be washed without being kept wa iting Electric installation is not grounded gt gt gt Check if your machine is connec ted to the actual grounding line Otherwise the static electric created in the product causes arcs on the surfaces of metal items creating pores removing the protective cover on the surface and causing discoloration Intensive cleansers such as bleaches are used gt gt gt Protective cover on metal surfaces gets damaged and looses its efficiency in time when it gets in contact with cleansers such as bleach Do not wash your dishes with bleach Metal items particularly such as knives are used for purposes other then their intended uses gt gt gt Protective cover on the edges of knives may get damaged when they are used for purposes such as opening cans Do not use metal kitchen utensils out of their intended uses Silverware are made of low quality stainless steel gt gt gt Corrosion on such items is inevitable they should not be washed in dishwashers Kitchen utensils that are already corroded are washed in dishwasher gt gt gt Rust on a corroded item can migrate to other stainless steel surfaces and cause corrosion on those surfaces as well Such items should not be was hed in dishwashers 42 EN Detergent remains in detergent dispenser Detergent dispenser was damp when adding detergent gt gt gt Make sure that the detergent dispenser is dried well
39. res 24 Collapsible upper basket wires 25 Adjusting the height of loaded upper basket 26 Adjusting the height of loaded upper basket 27 Adjusting the height of empty upper basket 28 5 Operating the product 29 Keys 30 Preparing the machine 30 Programme selection 30 Auxiliary functions 32 Programming the washing time 33 Starting the programme 34 Child Key Lock 34 Cancelling the programme 35 Salt indicator S 35 Rinse Aid indicator 2x 35 End of programme 35 6 Maintenance and cleaning 36 Cleaning the outer surface of the product 36 Cleaning the interior of the machine 36 Cleaning the filters 36 Cleaning the hose filter 37 Cleaning the impellers 37 7 Troubleshooting 39 4 Dishwasher Overview 1 Tabletop depends on the model 2 Upper impeller 3 Lower basket 4 Lower impeller 5 Filters 6 Control panel 7 Door 8 Detergent dispenser 9 Lower impeller slot 10 Silverware basket 11 Salt reservoir lid 12 Upper basket rail 13 Upper basket with rack 14 Fan drying system depends on the model 3 EN Technical specifications Development production and sales stages of this product comply C This product complies with the following EU directives with the safety rules included in all pertaining European Community regulations 2006 95 EC 2004 108 EC 93 68 EEC IEC 60436 EN 50242 consumption Power input 220 240 V 50 Hz Total power consumption 1800 2100 W Heater power 18
40. rwise the product may tilt e Never leave the door of the product open apart from loading and unloading procedures e Donotto open the door of the product when itis running unless necessary Be careful for the rush o hot steam when you need to open the door Intended use This appliance is intended to be used in household and Similar applications such as e Staff kitchen areas in shops offices and other working environments e farmhouses e by clients in hotels motels and other residential type environments e bed and breakfast type environments e Only dishwasher safe detergents rinse aids and additives must be used e The manufacturer waives any responsibility arisen from incorrect usage or transportation e Theservice life of your product is 10 years During this period Original Spare parts will be available to operate the appliance properly This product should not be used by persons with physical sensory or mental disorders or unlearned or inexperienced people including children unless they are attended by a person who will be responsible for their Safety or who will instruct them accordingly for use of the product Children s safety 6 EN Electrical products are dangerous for the children Keep children away from the product when It Is in use Do not let them to tamper with the product Do not forget to close the door of the product when leaving the room where it is located
41. sharp and pointed dishes such as service fork bread knife etc upside down so as their pointed ends will face down or they will lie horizontally on the dish baskets e Unload dishes in the lower basket first and then the dishes in the upper basket 16 Suggestions for loading the Improper Loading Of Dishware dishwasher TIRA Zn SI poi eT nmu ee Lower basket um Nay gt Y pugon Wo oor SOT n Silverware basket depends on the model Silverware basket is designed to wash your dishes such as fork spoon and etc in a cleaner manner rae re jar HH a SIS ABS IEEE zl rs N F UE AWA WV oon fo Eager Silverware basket piece depends on the model You can place your forks spoons and etc to upper basket with the additional piece in the figure Movable silverware basket depends on the model Since the cutlery basket can be moved A B you can create a wider space while placing your dishes to the lower basket and free up space for your dishes in different sizes Collapsible lower basket wires 2 pieces depends on the model The two piece foldable wires located at th
42. t must be installed on a flat surface in order for the door to be closed comfortably and securely Do not install the product at places where temperature may fall below 0 C Place the product at least 1 cm away from the edges of other furniture Place the product on arigid floor Do not place it on along pile rug or Similar surfaces Do not place the product on the power cable Make sure that you select a location that will allow you to load and unload the dishesina fast and comfortable manner Install the product in a place close to the tap and the drain hole Select the installation location by considering that it will not be changed after the connections are made Connecting water supply GJ We recommend attaching a filter on the house apartment supply water inlet to protect the machine from damages that may arise from impurities sand dirt rust etc coming from the urban water Supply system or from your own water system as well as to prevent complaints such as yellowing or EN sludge accumulation at the end of washing Permitted watertemperature up to 25 C The dishwasher may not be connected to open warm water devices or flow through water heaters e Donotuse old or used water inlet hose on the new product Use the new water inlet hose supplied with the product e Connect the water inlet hose directly to the water tap Pressure coming from the tap Should be minimum 0 3 and maximum 10 bars If t
43. tems in the dishwasher It can get corroded or leave stains on other items e Do not wash silverware and cutlery with wooden or bone stems glued pieces or pieces that are not resistant to heat as well as copper and tin plated containers in the dishwasher GJ Decorative prints of chinaware as well as aluminum and silver items may get discoloured or tarnished after washing in the dishwasher just as it happens in handwashing EN as well Some delicate glass types and crystals may become dullin time We strongly recommend you to check if the tableware you are going to purchase Is Suitable for washing especially in the dishwasher Placing the dishes into the dishwasher You can use your dishwasher in the optimum way with respect to energy consumption and washing and drying performance only if you place the dishes in an orderly way e Wipe away any coarse food remnants bones seeds etc on the dishes before placing them in the dishwasher e Place thin narrow pieces inthe middle sections of baskets if possible e There are two separate baskets in which you can place your dishes in the dishwasher Place the heavily soiled and bigger items in the lower basket and smaller delicate and light items in the upper basket e Place the hollowed dishes such as bowls glasses and pans upside down in the dishwasher Thus accumulation of water in deep hollows is prevented A To prevent possible injuries always place the
44. urn off the tap before attempting any cleaning procedures G Do not use abrasive substances for cleaning G Clean the filters and impellers at least once a week Cleaning the outer surface of the product Clean the outer surface and door gaskets of the product gently witha mild cleaning material and damp cloth Wipe the control panel only with a damp cloth Cleaning the interior of the machine Clean the interior of the machine and the tank by running a prewash programme without detergent or a long washing programme with detergent based on the degree of soiling If water has remained in the machine drain the water by performing the procedures under the topic Canceling a programme If the water cannot be discharged clean any leftover deposits that have piled up in the bottom of the machine blocking the water path Cleaning the filters Clean the filters at least once a week in order for the machine operates efficiently Check if food residues are 36 left on the filters If there are food residues on filters take them out and clean well under running water 1 Turn the micro filter 1 and coarse filter 2 assembly counter clockwise and pull it out from its seating A 2 Pullout the metal plastic filter 3 B 3 Press the two pawls on the coarse filter inwards and separate the coarse filter from the assembly 4 Cleanall three filters under tap water by means of a brus
45. voir lid is tightly closed after finishing the filling process Run the prewash programme to remove the salt that spilled inside the machine Since the salt granules that will remain under the lid will dissolve during prewash causing the lid loosen check the lid once again at the end of the programme Water hardness setting is low or Salt level is insufficient gt gt gt Measure the hardness of the supply water appropriately and check the water hardness setting Dishes are not placed orderly in the machine gt gt gt When placing the glas ses and other glassware into the basket lean them not against other dis hes but the edges or racks of the basket or the glass support wire Striking of the glasses to each other or to other dishes due to the impact of water during washing can cause breaks or scratches on their surfaces 43 EN A smear remains on glasses that resembles milk stain which can not be removed when wiped by hand A bluish rainbow appearance occurs when the glass Is pointed to light e Excessive rinse aid is used gt gt gt Lower rinse aid setting Clean the spilled rinse aid when adding rinse aid e Corrosion has occurred on glass due to soft water gt gt gt Measure the hard ness of the supply water appropriately and check the water hardness setting If your supply water Is soft lt 5 dH do not use salt Choose prog rammes that wash in higher temperatures e g 60 65 C You can also use glass protect
46. xplosion Put the detergent into the detergent dispenser just before operating the machine as illustrated below 13 1 Push the latch to right to open the detergent dispenser lid A 2 Putsuggested amount of powder or tablet detergent in the dispenser GJ Inside the detergent dispenser there are level markings that help you use appropriate amount of detergent When brimful detergent dispenser will contain 40 cm of detergent Fill detergent up to 15 cm or 25 cm level marks in the detergent dispenser according to fullness of the machine and or soiling degree of the dishes 1 GJ If dishes have been waiting fora long time and have dried residues fill the 5 cm compartment too 5 3 Close the detergent dispenser lid by pressing on it lightly A EN click will be heard when the lid is closed GJ In programmes with prewash and at high temperature in which you use tablet detergents make sure that the detergent dispenser lid is closed firmly GJ Use powder detergent in short programmes without prewash since the solubility of the tablet detergent changes depending on the temperature and time Z Excessive usage of powder detergents will cause the detergent not dissolve completely and will also cause scratches on the glassware Tablet detergents Table detergents exhibit water softening and or rinse aid effect in addition to detergent effect Some types of these detergents also contain sp
47. y the local authorities This product was manufactured using the latest technology in environmentally friendly conditions Dishwasher Instruction Manual Please read this user manual first Dear Customer We hope that you get the best results from the product which has been manufactured in state of the art plants and passed through a strict quality control procedure Therefore please read the entire user manual carefully before using the product and keep it as a reference for future use In case of transferring the product to someone else give the manual as well The user manual will help you use your product in a fast and safe way e Read the user manual before installing and starting your product e Always follow the safety instructions e Keep this user manual within easy reach for future reference e Read also the other documents supplied with the product Remember that this user manual is alSo applicable for several other models Differences between models will be identified in the manual Explanation of symbols Throughout this User Manual the following symbols are used Important information or useful hints about usage Warning for hazardous situations with regard to life and property Warning for electric shock Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations OPS P G Do not dispose of the packaging
Download Pdf Manuals
Related Search