Home

WTFF GROUP® G-1 Electric Skateboard

image

Contents

1. ccc ccc cee eee eee 21 Additional Information OND asec re nsec cesta A actin erase 21 Battery Information 000000000 c0cccccceeceeeeeeeeee 22 PEC CAUUOIG siscenacdscacsassnacenancncadasinciacwancnentancsadacnt 24 Trouble Shooting 25 SPECI NM CANONS seco asssscnevessedoetitccmeeoethaverstecs 27 Speed Controller 28 Charging Port Cover Contact Information ees 28 _ 3 Connect the charging adapter into the charging 5 Plug in the chargers AC adapter directly to a port wall outlet 6 When the G 1 Electric Skateboard is finished charging it will be indicated by a solid green light on the charger Please disconnect the AC adapter from the wall 7 Disconnect the charging adapter from the charging port and place charging port cover back on port Step Two Preparing the G 1 4 Screw the outer charging collar down ar a cael ee 1 Visually check for any damaged or loose nuts and bolt 2 Check front and rear axel nuts If they are loose tighten them x on a 3 Do not over tighten axel nuts 11 4 Check all six deck nuts and screws If they are loose tighten them If there are any missing nuts or screws replace them 5 Check all three motor screws If they are loose tighten them If there are any missing screws washers or spacers replace them before operating the G 1 Electric Skateboard Motor at amp Washers
2. The throttle switch is not connected to the wire The battery is drained Bad wire connections Batteries are not connected or not well connected Speed controller is not connected to the wire Motor is broken Motor is broken 2D Cause Litton Open the deck and check the wire and the connections Open the deck and check the wire and the connections Charge Replace the battery Power switch is broken Replace the switch Foot throttle is broken Replace the throttle Check and adjust all the wirings Battery is dead Replace the battery Check and adjust all the Connections Check and reconnect the wire Speed controller is broken Replace the controller Replace the motor Replace the motor Speed controller is broken Replace the controller Motor runs abnormally The noise of the motor is abnormal The battery cannot be charged or fully charged The headlights or taillights are not ON when the light switch is in the ON position Speed controller is broken Motor is broken Replace the controller Replace the motor Bad connection with the batteries Fuse is not connected well Check and adjust the Connections Check and adjust the Connections The axle of the motor is broken Rear axle is broken Rear axle screws are loosened Motor screws are loosened The battery is dead The charger is broken Fuse of the battery is
3. throttle is located on the top of the G 1 Electric Skateboard s deck towards the rear The G 1 Electric Skateboard comes standard with a 1 5 second power delay which can not be changed The G 1 Electric Skateboard turns in the same manner as a traditional skateboard You must lean it in order for it to turn the more you lean the smaller radius of the turn Please turn the lights on when operating the G 1 Electric Skateboard in low light areas The G 1 Electric Skateboard is not intended for trick riding DO NOT jump curbs with the G 1 Electric Skateboard Always be aware of your surroundings and the road conditions while you are operating the G 1 Getting Started eee Table of Contents Getting Started Step One Charging the Batteries Notice to USers cece cece ccc ceettetteeeeeeeeeeees 3 ig SC er en ere nee enna 5 1 Locate the charging port Getting Started Step one Charging the Batteries 00000 8 Step two Preparing the G 1 10 Step three Ride the G 1 0 14 x z ower Switch So PEN Y P Basic Operations Turning the G 1 s Power ON OF 15 Light Switch Turning the Running Lights ON OFF 16 Charging Port Setting the Stabilization Spring Tensioners 17 dla caf B01 0 1c aan en oe ene oe eee 20 How to Turn the G 1 0 eee ee 20 2 Remove the charging port cover How to Stop the G 1
4. 12 6 Check all front end nuts and screws If they are loose tighten them If there are any missing ones replace them 13 7 Check the stabilization spring Make sure the stabilization springs are compressed equally on both sides If the nuts will not stay in position you need to replace them 2 g g A S gewe w bert SMa Dy cota et i ar D 8 Applying Grip Tape Please clean the deck before applying grip tape Use soapy water or rubbing alcohol to clean the deck if it is necessary Step Three Ride Your G 1 14 Be sure that you have completed both Step One and Two Now you are ready to ride your G 1 Electric Skateboard Basic Operations Turning the Power ON OFF 1 Locate the system ON OFF switch on the side of the G 1 Electric Skateboard Power Switch Light Switch Charging Port 2 The ON OFF switch has two positions ON OFF The circle indicates an open circuit OFF and the line indicates a closed circuit ON 15 Turning the Running Lights ON OFF 1 Locate the Running Light ON OFF switch on the side of the G 1 Electric Skateboard Power Switch 2 Light Switch Charging Port 2 The Light switch has two positions ON OFF The circle indicates an open circuit OFF and the line indicates a closed circuit ON 16 Setting the Stabilization Spring Tensioners 1 Locate the stabilization spring tensioners od gee Lio ee Sa
5. Skateboard s batteries perform best on a warm day they will hold the highest charge and perform the best under warm temperatures The batteries capacity will fall about 33 if the temperature drops below l ldegrees Fahrenheit The batteries should be charged fully before the G 1 Electric Skateboard is stored for prolonged period of time and every month thereafter if still not in use Batteries specs 12 Volt 4 5 Ah 300 cycles Please recycle any unusable batteries 23 Precautions Do not discharge the batteries all the way Do not ride the G 1 in the water or under any wet conditions Do not jump off curbs No tricks Do not allow the G 1 to hit any objects such as people animals walls cars curbs and etc Always be aware of the road and weather conditions Always know your local and state regulations on electric driven vehicles Always wear safety gear an approved helmet knee and elbow pads for extra protection Do not ride the G 1 in areas where you will interrupt the flow of traffic Do not modify or alter your G 1 in any manners this will VOID your warranty Do not tow things with the G 1 unless specified otherwise Do not ride more than one rider at a time 24 Trouble Shooting Symptom Power switch is ON but the G1 cannot be operated The motor is not operating The speed of the motor is slow The wire to the switch is broken or not connected
6. charging system as alterations may cause fire or explosion Any tampering or alterations will void manufacturer s warranty Caution Electric Toy Notice for Users Please read this manual thoroughly before operating the G 1 Electric Skateboard All rights are reserved This manual may not be reproduced or translated without prior written approval from WTFF GROUP In no event will WTFF GROUP be responsible for any consequential or incidental damages or events that may occur from any information contained or omitted from this manual WTFF GROUP reserves the rights to make any changes to this manual and its contents at any time without notice WTFF GROUP also reserves the rights to make any changes to the G 1 Electric Skateboard at any time without notice In no event will WTFF GROUP be responsible for personal injury death damages to the G 1 Electric Skateboard or damages to any public and personal properties caused by the rider s negligence Before the initial use make sure the batteries are fully charged Otherwise you may cause severe damage to your G 1 Electric Skateboard s electrical system and your G 1 Electric Skateboard may never reach its full performance potential The G 1 Electric Skateboard is recommended for experienced extreme riders only The speed of the G 1 varies according to the grades of riding surface and rider s weight The G 1 Electric Skateboard is neither water proo
7. variable hand throttle The hand throttle conversion kit will be available at your local retailers How to Turn the G 1 The G 1 Electric Skateboard is a 3 wheel electrical motorized board which turns much like a traditional skateboard or a snowboard To turn the board you must lean the G 1 in the direction of where you want to go 20 Note The more you lean the smaller the turning radius How to Stop the G 1 Electric Skateboard Please be familiar with the foot controls on the G 1 Electric Skateboard before riding Locate the Rear brake pedal on the rear of the G 1 Electric Skateboard This pedal will serve as the manual foot brake on your G 1 Electric Skateboard Locate your rear foot break pedal Be sure you re able to pivot your foot from the throttle switch to the break pedal When you are prepared to stop the G 1 Electric Skateboard gentle apply pressure to the rear foot break pedal and then apply more pressure to stop quicker This action will stop your G 1 Electric Skateboard Note The more pressure you apply to the rear foot break pedal the quicker the G 1 Electric Skateboard will stop Charger There is a LED indication light on the charger The LED will light up to green red or flashing red and green 21 A red light means that the G 1 Electric Skateboard is charging and connected properly A green light means Charged or AC adapter is connected to the wall only or Charging adapter is conn
8. WTFF GROUP G 1 Electric Skateboard Operating Instructions Model No G1 2000 2005 WTFF GROUP All Rights Reserved Information For customers in the United States Interference may occur while operating this unit If this product does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following resolutions Reorient or relocate the receiving antenna Increase the separation between all equipment and the receivers Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for assistance Caution Any changes or modifications to the unit that are not expressly approved in this manual could void the warranty and your authority to operate this equipment If you have any questions about this product you may visit www wtffgroup com for information If you cannot find your answers there please e mail inquiries wtffgroup com Your inquiries will be replied by our professional staff WARNING Read and understand owner s manual carefully for proper use and charging Caution Shock Hazard Do not insert any foreign objects into this charging port Use only authorized charger originally provided with this unit Never modify electrical battery or
9. ar t mar i H Stabilization Flange 17 2 Set the stabilization spring Option 1 RECOMMENDED FOR NEW RIDERS To make the G 1 Electric Skateboard have a tighter and more stable feel turn the stabilization spring nuts clockwise towards the stabilization flange The more the nuts are turned clockwise towards the stabilization flange the more stable the G 1 Electric Skateboard will feel 18 Option 2 RECOMMENDED FOR ADVANCED RIDER ONLY To make the G 1 Electric Skateboard have a looser feel and easier maneuverability turn the stabilization spring nuts counter clockwise away from the stabilization flange DO NOT allow the stabilization nuts to completely come off the tie rod threads Make sure that the nylon ring in the lock nut is in full contact with the threads 19 Make sure the stabilization springs are compressed equally on both sides If the nuts will not stay in their positions you need to replace them The Throttle The throttle on the G 1 Electric Skateboard is not a variable throttle controller The throttle adapted to the G 1 Electric Skateboard is an ON OFF switch The speed of the G 1 Electric Skateboard can only be controlled by pressing or releasing the ON OFF throttle switch which is located on the top rear deck The G 1 Electric Skateboard s throttle is a foot throttle It is not a hand throttle Note The foot throttle switch can be converted to a
10. broken Fuse of the battery is not connected well ights are broken Bad wirings or connections Light switch is not connected well Replace the motor Replace the rear axle Check and tighten the screws Check and tighten the screws Replace the batteries Replace the charger Replace the fuse Check and adjust the Connections Check and adjust the wirings and connections Check and adjust the connection Light switch is broken Replace the light switch 26 Specifications Color Speed Max Load Range Age Aluminum deck with red wheels and black frame Up to 13 mph depending on terrain and rider s weight For Experienced Riders Only Motor Drive train Braking System Battery Box Size Wheel diameter Wheel Count Charging Time Safety Equipment Contents 220 Ibs Approx 4 5 Miles 16 200W Belt Drive Manual back foot brake 12Vx 2 4 5 Ah 31 L x 11 W x 7 8 H 5 3 4 6 hrs Three LED Front Headlights and Two Rear Tail Lights one G 1 Electric Skateboard one charger pre cut grip tape extra grip tape spare belt user manual and tool kit 21 The Speed Controller The G 1 Electric Skateboard has adopted a non variable speed controller with the ability to be converted into a variable speed controller with a variable hand throttle available at your local retailer or www wtffgroup com This speed controller runs on a 24Volts syste
11. ected only or The charger 1s connected improperly A flashing green and red light means that the batteries are 80 charged The G 1 Electric Skateboard charger is designed specifically for the G 1 DO NOT use any other charger with the G 1 When charging the G 1 the charger or the G 1 does not need to be attended to The approximate charging time for the G 1 Electric Skateboard is 4 to 6 hours Do not leave the charger connected to the G 1 more than 8 hours Battery Information The batteries selected for the G 1 Electric Skateboard are lead acid dry cell batteries These batteries are solely used for electric vehicles because they are maintenance free durable possessing high energy storing capacity and long life 22 These batteries will gradually loose their capacity to hold a full charge over time and usage These batteries have a life of about 300 cycles one cycle is a full charge and discharge For every cycle the range of the G 1 will decrease due to the nature of its batteries The life of the batteries will decrease dramatically if the batteries are completely discharged time after time It is a good idea to keep the G 1 charged at all times even when not in use Charging the batteries after each use and charging the G 1 Electric Skateboard once a month when not in use will prolong the life of the batteries Environmental temperature plays a large role in the performance of the batteries The G 1 Electric
12. f nor water resistant DO NOT operate the G 1 in any wet conditions This action may cause permanent damage to the product and the warranty will be voided Check all nuts and bolts before and after each ride WTFF GROUP does not warrant any acts of God RIDERS OF THESE BOARDS ASSUME ALL RISK OF OPERATION INCLUDING SERIOUS BODILY INJURY AND OR DEATH Note Street legal as 09 09 2004 in the State of California and neighboring States Please check your local and State laws and regulations to confirm the Street Legal status of the G 1 Electric Skateboard Preface Thank you for purchasing the G 1 Electric Skateboard from WTFF GROUP We hope that the G 1 Electric Skateboard will bring you years of entertainment and satisfaction Check your local state and city regulations before riding the G 1 Electric Skateboard on public roads and properties The G 1 Electric Skateboard is intended for private property only DO NOT operate or ride the G 1 Electric Skateboard in crowded areas or places where you will cause interruptions in the flow of traffic Always wear safety gear an approved helmet along with knee and elbow pads for extra protection Adult supervision is required for riders under the age of 18 For use of experienced riders over the age of 16 The G 1 Electric Skateboard is a foot controlled electrical motorized three wheel board The foot throttle is not a variable controller The foot
13. m with an 82 Watts continuous current system which is made specifically for electric driven vehicles This speed controller has been selected for the G 1 Electric Skateboard because of its light weight small size robustness and its ability to handle high power draws and loads Contact information General Inquiries inquiries wtffgroup com Technical questions tech wtffgroup com General Information info wttffgroup com For updated news upcoming events and information of accessories and speed kits please visit www wtffgroup com 28

Download Pdf Manuals

image

Related Search

Related Contents

S TEST Reagent Cartridge Triglycerides (TG (  DEH-P4400R DEH-P4400RB - Pioneer Europe  Western Digital WDBKXH3200ABKNESN Computer Drive User Manual  WeatherFlash V1.0 User`s Manual  Télécharger : Manuel installation & entretien SPM  Xerox 320 User's Manual  Radio AM/FM con Reloj Despertador (120  2711E-818ES, Software de Configuración PanelBuilder 1400e para  Philips 046677418441 energy-saving lamp  Reader Terminal Keypad Technical Manual  

Copyright © All rights reserved.
Failed to retrieve file