Quick Start Guide
Contents
1. Note For more information on jumper selections see the 9000X AF Drives User Manual Chapter 4 5 SVX9000 Drives MN04003009E November 2011 Jumper Block X3 CMA and CMB Grounding ee CMB connected to GND ee CMA connected to GND CMB isolated from GND ele CMA isolated from GND ele CMB and CMA internally connected ele together isolated from GND Factory default www eaton com STEP 3 Start Up Wizard If the wizard is not enabled at power up press the STOP button for 5 secs to enable it Startup Wizard Language Application Press Enter lt 3 English Standard o 3 5 Seconds Wait O f OXO Setup Starts Min Freq Max Freq G gt Press Enter lt 3 0 00 Hz lt 3 60 00 Hz lt O O Accel Time 1 QO Decel Time 1 QO Current Limit QO S0 s 3 0 s 3 30 A kerr y O O O Motor NP Volt oxo Motor NP Freq QO Motor NP Speed QO 460 V lt 3 60 00 Hz lt 3 1720 rpm L y P O O O Motor NP Current G Power Factor Q Loc Ctrl Place Oxo 2 20 A lt 3 0 85 lt 3 Keypad lt Y O OXO Rem Ctrl Place Local Reference Remote Reference I O Terminal lt 3 Keypad sd ALI lt r y O OXO Input Phase Supv2. Repeat Setup Setup Done Fault Coast lt w lt No Yes gt lt e Press Enter Copy Parameters Up to Keypad Up to Keypad lt No Yes gt om lt No Yes gt Wait Output Frequency 0 00 Hz SVX9000 Drives MN04003009E November 2011 www eaton com STEP 4 Operating amp Programming Menu Navitation Main Menu The data on the control keypad are arranged in menus and submenus The first menu level consists of M1 to M8 and is called the Main Menu The structure of these menus and their submenus is illustrated below Some of the submenus will vary for each application choice Main Menu Navigation Q M1 Parameters G1 1 M2 Keypad Control R2 1 Keypad Reference P2 2 Keypad Direction Cix P2 x Stop Button Active M3 Active Faults 4A3 1 Active Fault 1 Menu Navigation T3 1 1 Operation Days T3 1 13 Zero Speed Up Arrow The up arrow et advances to the next A3 x Active Fault x menu item A PRERE g the 7 Ma4 Sey Meehan Fault up arrow once wi fp H4 j advance from M1 to M2 T4 1 1 Operation Days Down Arrow The down T4 1 13 Zero Speed arrow backs up to the ee previous menu item H4 1 x Oldest Saved Fault For example pressing the 1 M5 System Menu down arrow once will back 5 1 Language up from M2 to M1 5 2 Application r x S5 3 Copy Par
3. 7 Some of the submenus will vary for each application choice STEP 2 Standard Wiring Diagrams and Terminal Locations Power and Motor Wiring Terminal Schematic for SVX9000 Drives Power Board 230V 1 15 hp 480V 1 1 2 30 hp Control Board f T External External RFI Filter Filter Optional Optional l A zi Ll 2 1 a 3 JE SVX9000 Power and Motor Wiring for Low Horsepower Drives 1 30 hp 3 SVX9000 Drives MN04003009E November 2011 www eaton com STEP 2 Continued Power Board 230V 20 30 hp 480V 40 250 hp Control Board I f External External RFI Filter Filter Optional Optional Pp Ng L1 12 13 Ff i a JL SVX9000 Power and Motor Wiring for Large Horsepower Drives 20 250 hp SVX9000 Drives MN04003009E November 2011 www eaton com STEP 2 Continued Standard Application Default I O Configuration Reference potentiometer Terminal Signal Description Toy a OPTA1 r4 H 41 10V ef Reference output Voltage for potentiometer l etc l 42 Al1 Analog input Voltage input frequency voltage range reference l 0 10V DC b 4 3 Al1 1 0 Grou
4. M1 gt G1 3 Code Parameter Min Max Unit Default Cust ID Note P1 3 1 Analog 0 A 464 TTF programming output 1 method used signal selection P1 3 2 Analog 0 8 1 307 0 Not used output 1 Output freq function 0 fmax 2 Freq reference 0 fmax 3 Motor speed 0 Motor nominal speed 4 Motor current O InMotor 5 Motor torque O0 TnMotor 6 Motor power O PrMotor 7 Motor voltage O Un motor 8 DC Bus volt 0 1000V P1 3 3 Analog 0 00 10 00 js 1 00 308 0 No filtering output filter time SVX9000 Drives MN04003009E November 2011 www eaton com Parameter value can only be changed after the drive has been stopped STEP 4 Continued Output Signals M1 gt G1 3 Continued Code Parameter Min Max Unit Default Cust iD Note P1 3 4 Analog output 0 1 0 309 0 Not inverted inversion 1 Inverted P1 3 5 Analog output 0 1 0 310 0 0 mA minimum 1 4mA P1 3 6 Analog output 10 1000 100 scale P1 3 7 Digital output 1 0 16 1 function 312 0 Not used 1 Ready 2 Run 3 Fault 4 Fault inverted 5 FC overheat warning 6 Ext fault or warning 7 Ref fault or warning 8 Warning 9 Reversed 10 Preset speed 1 11 At speed 12 Mot regulator active 13 OP freq limit 1 superv 14 Remote Control Active 15 Thermistor fault warng 16 Fieldb
5. P1 4 5 Brake 0 4 0 504 0 Disabled chopper 1 Used when running 2 External brake chopper 3 Used when stopped running 4 Used when running no testing P1 4 6 Start function 0 1 0 505 0 Ramp 1 Flying start P1 4 7 Stop function 0 3 1 506 0 Coasting 1 Ramp 2 Ramp Run enable coast 3 Coast Run enable ramp P1 4 8 DC braking 0 00 JIL A 0 7 x ly 507 current P1 4 9 DC braking 0 00 600 00 s 0 00 508 0 DC brake is off time at stop at stop P1 4 10 Frequency to 0 10 10 00 Hz 1 50 515 start DC braking during ramp stop P1 4 11 DC braking 0 00 600 00 s 0 00 516 0 DC brake is off time at start at start P1 4 12 Flux brake 0 1 0 520 0 Off 1 On P1 4 13 Flux braking 0 1 IL A ly 519 current x ly Parameter value can only be changed after the drive has been stopped Prohibit Frequencies M1 gt G1 5 Code _ Parameter Min Max Unit Default Cust ip Note P1 5 1 Skipfrequency 0 00 Par Hz 0 00 509 range 1 low 1 5 2 limit P1 5 2 Skipfrequency 0 00 Par Hz 0 0 510 0 Skip frequency range 1 high 1 1 2 range 1 not limit used P1 5 3 Skipfrequency 0 1 10 0 1 0 518 acc dec ramp SVX9000 Drives MN04003009E November 2011 www eaton com STEP 4 Continued Motor Control Parameters M1 gt G1 6 Code _ Parameter Min Max Unit Default Cust iD Note P1 6 1 Motor 0 1 6 0
6. 103 time 1 P1 1 4 Deceleration 0 1 3000 0 s 3 0 104 time 1 P1 1 5 Current limit 0 1x 2xly A IL 107 ly P1 1 6 Nomina 180 690 Vv P 230V 110 voltage of P 460V the motor P 575V P1 1 7 Nomina 30 00 320 00 Hz 60 00 111 Check the rating frequency of plate of the the motor motor P1 1 8 Nomina 300 20 000 rpm 1720 112 The default applies speed of the for a 4 pole motor motor and a nominal size frequency converter P1 1 9 Nomina 0 1x 2xly JA ly 113 Check the rating current of the ly plate of the motor motor P1 1 10 Power Factor 0 30 1 00 0 85 120 Check the rating plate of the motor P1 1 11 Local Control 1 3 2 171 1 1 0 Terminal Place 2 Keypad 3 Fieldbus P1 1 12 Remote 1 3 1 172 1 I O Terminal Control 2 Keypad Place 3 Fieldbus P1 1 13 Local 0 3 2 173 0 Al1 reference 1 Al2 2 Keypad 3 Fieldbus P1 1 14 Remote 0 3 0 174 0 Al1 reference 1 Al2 2 Keypad 3 Fieldbus P1 1 15 Identification 0 2 0 631 0 Not used 1 V Hz 2 V Hz with boost P1 1 16 V Hz Opt 0 1 0 109 0 Not used 1 Automatic torque boost P1 1 17 Preset 0 00 Par Hz 10 00 105 Speeds preset by speed 1 CE2 operator P1 1 18 Preset 0 00 Par Hz 40 00 106 speed 2 1 1 2 Parameter value can only be changed after the drive has been stopped 9 SVX9000 Drives MN04003009E November 2011 www eaton com STEP 4 Continued Input Signa
7. 600 SVX control 0 Frequency mode control 1 Speed control Additionally for SPX 2 Torque control 3 Closed loop speed ctrl 4 Closed loop torque ctrl P1 6 2 V Hz 0 1 0 109 0 Not used optimization 1 Automatic torque boost P1 6 3_ V Hz ratio 0 3 0 108 0 Linear selection 1 Squared 2 Programmable 3 Linear with flux optim P1 6 4 Field 8 00 320 00 Hz 60 00 602 weakening point P1 6 5 Voltage at 10 00 200 00 100 00 603 n x Unmot field weakening point P1 6 6 V Hz curve 0 00 Par Hz 60 00 604 midpoint 1 6 4 frequency P1 6 7 V Hz curve 0 00 100 00 100 00 605 n x Unmot midpoint Parameter max voltage value par 2 6 5 P1 6 8 Output 0 00 40 00 1 30 606 n x Unmot voltage at zero frequency P1 6 9 Switching 1 0 Varies kHz Varies 601 See Table 8 12 on frequency page 57 for exact values P1 6 10 Overvoltage 0 2 1 607 0 Not used controller 1 Used no ramping 2 Used ramping P1 6 11 Undervoltage 0 1 1 608 1 Yes controller 2 No P1 6 12 Load 0 00 100 00 0 00 620 Drooping of Drooping nominal speed at nominal torque P1 6 13 Identification 0 1 0 631 0 Not used 1 OL v f Ratio 2 OL v f and Boost Parameter value can only be changed after the drive has been stopped Output Signals M1 gt G1 3 Code _ Parameter Min Max Unit Default Cust ip Note P1 7 1 Response to 0 6 6 700 0 No response refere
8. SVX9000 Drives Quick Start Guide Effective November 2011 Supersedes December 2003 CONTENT STEP 1 Keypad Operation Overview STEP 2 Standard Wiring Diagrams and Connections STEP 3 Start Up Wizard STEP 4 Operating and Programming Menu Navigation STEP 5 Faults and Warning Indication STEP 6 Monitoring Menu E T N Powering Business Worldwide STEP 1 Keypad Operation Overview bun ToT yp stor PReapy ALARM FAULT 68888 meaa remote local fault Qe OC O O la Keypad and Display LCD Status Indicators Indicator Description Run Indicates that the SVX9000 is running and controlling the load Blinks when a stop command has been given but the SVX9000 is still ramping down Counterclockwise Operation The output phase rotation is BAC corresponding to counterclockwise rotation of most motors Clockwise Operation The output phase rotation is ABC corresponding to clockwise rotation of most motors RON Sto lt D ae that the SVX9000 is stopped and not controlling the load Ready READY ndicates that the SVX9000 is ready to be started Alarm ALARM ndicates that there is one or more active drive alarm s Fault qa ndicates that there is one or more active drive fault s ae 1 0 Terminal ndicates that the I O terminals have been chosen for control Keypad CED ndicat
9. ameters Right Arrow The right S5 4 Compare Parameters arrow will advance to the 5 5 Security next level in the menu 5 6 Keypad Settings For example pressing the H 5 7 Hardware Settings right arrow once will e advance from M2 to R2 1 5 8 System Information O M6 Expander Boards Left Arrow The left G6 1 Slot A Board arrow will back up one EAN level in the menu G6 5 Slot E Board structure M7 Monitor For example pressing the left arrow once will back V7 1 Output Frequency 0 00 Hz up from R2 1 to M2 V7 2 Frequency Reference 0 00 Hz M7 1x Multimonitor Nx M8 Operate Mode 01 Output Frequency 0 0 Hz 02 Freq Reference 0 0 Hz Ox Note Enter Key Holding the Enter key for more than 3 seconds will allow you to go directly to the programming mode 7 SVX9000 Drives MN04003009E November 2011 www eaton com STEP 4 Continued Operate Menu M8 The Operate Menu provides a easy to use method of viewing key numerical Monitoring Menu items Some applications also support the setting of reference values in this menu The items displayed vary by application The table below is an example for the Standard application Operate Menu Items Standard Application Example Code Signal Name Unit Description 0 1 Output Frequency Hz Output frequency 0 2 FreqReference Hz Fre
10. ault 6 Emergency stop 25 Microprocessor 44 Device change watchdog fault different type 7 Saturation trip 26 Startup prevented 45 Device added different type 8 System fault 29 Thermistor fault 50 Analog input lin lt 4 mA for the signal range 4 to 20 mA 9 Undervoltage 31 IGBT temperature 51 External fault hardware 10 Input line 32 Fan heat sink 52 Keypad supervision communication fault 11 Output phase 34 CAN bus 53 Communication supervision communication bus fault 12 Brake chopper 36 Control unit 54 Slot fault supervision 13 SVX9000 37 Device change 56 PT100 board undertemperature same type temperature fault 14 SVX9000 38 Device added overtemperature same type 15 Motor stalled 39 Device removed SVX9000 Drives MN04003009E November 2011 www eaton com STEP 6 Monitoring Menu M7 The Monitoring Menu items are meant for viewing parameter values during operation Monitored values are updated every 0 3 sec Monitored items are identified by item numbers V7 1 to V1 xx where xx varies by application The table below provides an example of the monitored values for the Standard application Monitored parameters are not editable from this menu See Parameter Menu M1 to change parameter values Monitoring Menu Items Standard Application Example Code Signal Name Unit Description V7 1 Output Hz Output frequency Frequency V7 2 Frequency Hz Fr
11. equency reference setting reference V7 3 Motor speed rom Calculated motor speed V7 4 Motor current A Measured motor current V7 5 Motor torque Calculated torque based on nominal motor torque V7 6 Motor power Calculated power based on nominal motor power V7 7 Motor voltage v Calculated motor voltage V7 8 DC bus voltage V Measured DC bus voltage V7 9 Unit temperature C Heatsink temperature V7 10 Calculated motor C Calculated motor temperature based on the temperature motor nameplate information and the calculated motor load V7 11 Analog Input 1 Vv Voltage input at Terminals Al1 and GND V7 12 Analog input 2 mA Current input at Terminals Al2 and Al2 V7 13 DIN1 DIN2 DIN3 Digital input status see figure below V7 14 DIN4 DIN5 DIN6 Digital input status see figure below V7 15 DO1 RO2 RO3 Digital and relay output status see figure below V7 16 Analog lout mA Current output at Terminals AO1 and A01 V7 17 Multimonitor See below V1 13 DIN1 DIN2 DIN3 OFF ON OFF Digital Inputs DIN1 DIN2 DIN3 Status v1 14 DIN4 DINS DING ON OFF OFF Digital Inputs DIN4 DIN5 DIN6 Status V1 15 DO1 RO1 RO2 OFF OFF ON Digital and Relay Outputs DO1 RO1 RO2 Status Multimonitor V7 17 This parameter allows the viewing and selection if allowed by System menu item P5 5 4 o
12. es that the keypad has been chosen for control Bus Communications Bus comm ndicates that the communications bus control has been chosen for control LED Status Indicators Indicator Description local Local Steady Illumination ndicates that the SVX9000 is ready to be started and operated from the Local mode Local Flashing ndicates that the SVX9000 is ready for operating command to select Local or Remote operation remote Remote ndicates that the SVX9000 is operating and controlling the load remotely Remote Flashing ndicates that the SVX9000 is ready for operating command to select Local or Remote operation fault Fault ndicates that there is one or more active drive fault s 1 SVX9000 Drives MN04003009E November 2011 www eaton com STEP 1 Continued Navigation Buttons Button Description Start This button operates as the START button for normal operation when the Keypad is selected as the active control lt enter oJ Enter This button is used in the parameter edit mode to save the parameter setting and move to the next parameter to reset the Fault History if pressed while in the Fault History menu to confirm the acceptance of a change to change a virtual button status while in the Button menu to confirm the start up list at the end of the Start Up Wizard when the Operate menu is active to e
13. f three simultaneously monitored items from the Monitored Menu Items shown in the table above Use the right arrow key to select the item to be modified and then the up or down arrow keys to select the new item Press the ENTER key to accept the change 17 SVX9000 Drives MN04003009E November 2011 www eaton com E T N Powering Business Worldwide Eaton is dedicated to ensuring that reliable efficient and safe power is available when it s needed most With unparalleled knowledge of electrical power management across industries experts at Eaton deliver customized integrated solutions to solve our customers most critical challenges Our focus is on delivering the right solution for the application But decision makers demand more than just innovative products They turn to Eaton for an unwavering commitment to personal support that makes customer success a top priority For more information visit www eaton com electrical Eaton Corporation Electrical Sector 1111 Superior Ave Cleveland OH 44114 United States 877 ETN CARE 877 386 2273 Eaton com Eaton is a registered trademark of Eaton 2011 Eaton Corporation Corporation All Rights Reserved Printed in USA All other trademarks Publication No MNO4003009E Z11191 are property of their November 2011 respective owners
14. ls M1 gt G1 2 Code Parameter Min Max Unit Default Cust ID Note P1 2 1 Start Stop 0 6 0 300 DIN1 DIN2 E logic 0 Start fwd Start rvs 1 Start Stop Rvs Fwd 2 Start Stop Run enable 3 Start Stop pulse pulse 4 Fwd Rvs 5 Start Rvs Stop Fwd 6 Start Run Stop enable P1 2 2 DIN3 0 7 1 301 0 Not used function 1 Ext fault closing cont 2 Ext fault opening cont 3 Run enable 4 Acc Dec time select 5 Force CP to Remote 6 Rvs if par 1 2 1 3 P1 2 3 Current 0 1 1 302 0 0 20mA reference 1 4 20mA offset P1 2 4 Reference 0 00 Par Hz 0 00 303 Selects the frequency scaling 1 2 5 that corresponds to the minimum min reference signal value 0 00 No scaling P1 2 5 Reference 0 00 320 00 Hz 0 00 304 Selects the frequency scaling that corresponds to the maximum max reference signal value 0 00 No scaling P1 2 6 Reference 0 1 0 305 0 Not inverted inversion 1 Inverted P1 2 7 Reference 0 00 10 00 s 0 10 306 0 No filtering filter time P1 2 8 Al1 signal A 1 377 TTF programming selection method used P1 2 9 Al2 signal A 2 388 TTF programming selection method used Parameter value can only be changed after the drive has been stopped Use TTF method to program these parameters Rising edge required to start CP control place Output Signals
15. nce 1 Warning fault 2 Warning Previous Freq 3 Wrng PresetFreq TAZ 4 Fault stop acc to 1 4 7 5 Fault stop by coasting 6 Fault Restart 13 SVX9000 Drives MN04003009E November 2011 www eaton com STEP 4 Continued Protections M1 gt G1 7 1 Fault low 2 Fault high Code _ Parameter Min Max Unit Default Cust iD Note P1 7 2 Reference fault 0 00 Par Hz 0 00 728 frequency 1 1 2 P1 7 3 Response to 0 3 2 701 0 No response external fault 1 Warning P1 7 4 Inputphase 0 3 3 730 2 Eault stop supervision 3 Fault stop P1 7 5 Response to 1 3 0 727 by coasting undervoltage fault P1 7 6 Output phase 0 3 2 702 supervision P1 7 7 Earth fault 0 3 2 703 protection P1 7 8 Thermal 0 3 2 704 protection of the motor P1 7 9 Motor ambient 100 0 100 0 0 0 705 temperature factor P1 7 10 Motor cooling 0 0 150 0 40 0 706 factor at zero speed P1 7 11 Motor thermal 1 200 min 45 707 time constant P1 7 12 Motor duty 0 100 100 708 cycle P1 7 13 Stall protection 0 3 0 709 0 No response 1 Warning 2 Fault stop acc to 1 4 7 3 Fault stop by coasting P1 7 14 Stall current 0 1 InMotor A IL 710 x2 P1 7 15 Stall time limit 1 00 120 00 s 15 00 711 P1 7 16 Stall frequency 1 0 Par Hz 25 0 712 limit 1 1 2 P1 7 17 Underload 0 3 0 713 0 No response protection 1 Warni
16. nce source Used to set the password if defined when leaving the Operate menu scroll through the Active Faults menu when the SVX9000 is stopped Menu Navigation Navigation Tips e To navigate within one level of a menu use the up and down arrows e To move deeper into the menu structure and back out use the right and left arrows e To edit a parameter navigate to show that parameter s value and press the right arrow button to enter the edit mode In edit mode the parameter value will flash SVX9000 Drives MN04003009E November 2011 www eaton com STEP 1 Continued e When in edit mode the parameter value can be changed by pressing the up or down arrow keys e When in edit mode pressing the right arrow a second time will allow you to edit the parameter value digit by digit e Toconfirm the parameter change you must press the ENTER button The value will not change unless the ENTER button is pushed e Some parameters can not be changed while the SVX9000 is running The screen will display LOCKED if you attempt to edit these parameters while the drive is running Stop the drive to edit these parameters See the SVX9000 Application Manual for identification of these parameters specific to your chosen application Main Menu The data on the control keypad are arranged in menus and submenus The first menu level consists of M1 to M8 and is called the Main Menu The Main Menu is illustrated on Page
17. nd Ground for reference and controls 4 Al2 Analog input Current input frequency current range reference 5 Al2 0 20 mA r 4 6 24V Control voltage Voltage for switches etc output max 0 1A fi GND O ground Ground for reference and controls er gt OE 8 DIN1 Start forward Contact closed start forward programmable pa aag DIN2 Start reverse Contact closed start reverse l programmable a ere 10 DIN3 External Contact open no fault fault input Contact closed fault programmable 11 CMA Common for DIN1 Connect to GND or 24V DIN3 12 24V Control voltage Voltage for switches see 6 output r 413 GND 1 0 ground Ground for reference and l controls r a 414 DIN4 Multi step speed DIN4 DIN5 Frequency l select 1 ref om ae eel 1 DIN5 Multi step speed Open Open Ref Uin select 2 Closed Open Multi step ref 1 Open Closed Multi step I ref 2 j Closed Closed Ref lin a a l 416 DING Fault reset Contact open no action Contact closed fault reset I 17 CMB Common for DIN4 Connect to GND or 24V i DING 418 AO1 Output frequency Programmable Analog output Range 0 20 mA R 719 A01 iii ma 500W 420 DO1 Digital output Programmable READY Open collector lt 50 mA U lt 48V DC i OPTA2 21 RO1 _ Relay I output 1 L RUN Le 122 RO1 E RUN L amp 423 RO1 24 RO2 a Relay 220V 425 RO2 ote AC 426 ROZ I
18. ng 2 Fault stop acc to 1 4 7 3 Fault stop by coasting P1 7 18 Field 10 150 50 714 weakening area load P1 7 19 Zero frequency 5 0 150 0 10 0 715 load P1 7 20 Underload 2 600 s 20 716 protection time limit P1 7 21 Response to 0 3 2 732 0 No response thermistor fault 1 Warning 2 Fault stop acc to 1 4 7 3 Fault stop by coasting P1 7 22 Response to 0 3 2 733 See P1 7 21 fieldbus fault P1 7 23 Response to 0 3 2 734 See P1 7 21 slot fault P1 7 24 FB MCW Bit 15 0 2 0 771 0 No action SVX9000 Drives MN04003009E November 2011 www eaton com 14 STEP 4 Continued Auto Restart Parameters M1 gt G1 8 Code Parameter Min Max Unit Default Cust ID Note P1 8 1 Wait time 0 10 10 00 js 0 50 717 P1 8 2 Trial time 0 00 60 00 s 30 00 718 P1 8 3 Start function 0 2 0 719 0 Ramp 1 Flying start 2 According to par 1 4 6 P1 8 4 o Number of tries 720 after ndervoltage trip E P1 8 5 o o Number of tries 721 after overvoltage trip P1 8 6 o w Number of tries 722 ter a overcurrent trip P1 8 7 o Number of tries 723 after reference trip P1 8 8 Oo o Number of tries 726 after motor temperature fault trip P1 8 9 o o Number of tries 725 ter external fault trip v P1 8 10 Number of tries
19. o 738 ter underload fault trip v Keypad Control M2 This menu provides the parameters for the setting of the keypad frequency reference the selection of motor direction when in keypad operation and when the STOP button is active Keypad Control Parameters M2 Code Parameter Min Max Unit Default Cust ip Note P2 1 Control place 0 3 0 1685 0 Keypad L R 1 Local 2 Remote 3 1 0 force R2 1 Keypad Par Par Hz reference 1 1 1 1 1 2 P2 3 Direction on 0 1 0 123 0 Forward keypad 1 Reverse P2 4 Stop button 0 1 1 114 0 Limited function of Stop button 1 Stop button always enabled P2 5 Operate menu 0 1 0 1688 0 No hide 1 Yes Other Menus M3 to M6 Menus M3 to M6 provide information on the Active Faults Fault History System Menu settings and the Expander Board setup These menu items are explained in detail in Chapter 5 of the SVX9000 User Manual 15 SVX9000 Drives MN04003009E November 2011 www eaton com STEP 5 Faults and Fault Codes Code Fault Directory Fault Fault Fault Code Fault Code Fault Code Fault 1 Overcurrent 16 Motor 40 Device unknown overtemperature 2 Overvoltage 17 Motor underload 41 IGBT temperature 3 Ground Earth 22 EEPROM 42 Brake resistor Fault checksum fault overtemperature 5 Charging Switch 24 Counter fault 43 Encoder f
20. quency reference 0 3 Motor Speed rom Calculated motor speed 0 4 Motor Current A Measured motor current 0 5 Motor Torque Calculated torque based on nominal motor torque 0 6 Motor Power Calculated power based on nominal motor power 0 7 Motor Voltage V Calculated motor voltage 0 8 DC Bus Voltage V Measured DC bus voltage 0 9 Unit Temperature SC Heatsink temperature 0 10 MotorTemperature Calculated motor temperature based on the motor nameplate information and the calculated motor load R1 Keypad Reference Hz Keypad frequency reference setting The menu is navigated by using the left and right arrow buttons If a reference level is available for setting the up and down arrow buttons adjust the value To exit the Operate Menu to access the other menus depress the ENTER button for 2 seconds While in the other menus if there is no keypad activity the display will return to the Operate Menu after 30 seconds SVX9000 Drives MN04003009E November 2011 www eaton com STEP 4 Continued Parameters M1 Standard Parameters M1 Code _ Parameter Min Max Unit Default Cust ID Note P1 1 1 Min 0 00 Par Hz 0 00 101 frequency 1 1 2 P1 1 2 Max Par 320 00 Hz 60 00 102 NOTE If fmax gt frequency 1121 than the motor synchronous speed check suitability for motor and drive system P1 1 3 Acceleration 0 1 3000 0 s 3 0
21. us input data 313 Same as parameter 1 3 7 314 Same as parameter 1 3 7 315 0 No limit 1 Low limit P1 3 8 Relay output1 0 16 2 function P1 3 9 Relay output2 0 16 3 function P1 3 10 Output 0 2 0 frequency limit 1 supervision supervision 2 High limit supervision P1 3 11 Output 0 00 320 00 Hz 0 00 316 frequency limit 1 Supervised value P1 3 12 Analog output 0 0 1 471 TTF 2 signal programming selection method used P1 3 13 Analog output 0 8 4 472 Same as 2 function parameter 1 3 2 P1 3 14 Analog output 0 00 10 00 s 1 00 473 0 No filtering 2 filter time P1 3 15 Analog output 0 1 0 474 0 Not inverted 2 inversion 1 Inverted P1 3 16 Analog output 0 1 0 475 0 0 mA 2 minimum 1 4mA P1 3 17 Analog output 10 1000 100 476 2 scaling Parameter value can only be changed after the drive has been stopped 11 SVX9000 Drives MN04003009E November 2011 www eaton com STEP 4 Continued Drive Control Parameters M1 gt G1 4 Code _ Parameter Min Max Unit Default Cust iD Note P1 4 1 Ramp 1 0 0 10 0 s 0 0 500 0 Linear shape gt 0 S curve ramp time P1 4 2 Ramp 2 0 0 10 0 s 0 0 501 0 Linear shape gt 0 S curve ramp time P1 4 3 Acceleration 0 1 3000 0 s 10 0 502 time 2 P1 4 4 Deceleration 0 1 3000 0 s 10 0 503 time 2
22. xit the Operate submenu Stop This button has two integrated operations The button operates as STOP button during normal operation motor STOP from the keypad which is always active unless disabled by the StopButtonActive parameter used to reset the active faults Reset Resets the active faults Local Remote Switches between LOCAL and REMOTE control for start speed reference and reverse functions The control locations corresponding to local and remote can be selected within an application Left Arrow navigation button movement to left in parameter edit mode exits mode backs up one step cancels edited parameter exit from a parameter edit mode When in Operate menu will move backward through menu Atend of Start Up Wizard repeats the Start Up Wizard setup menu Right Arrow navigation button movement to right enter parameter group mode enter parameter mode from group mode When in Operate menu will move forward through menu Up and Down Arrows move either up or down a menu list to select the desired menu item editing a parameter password while the active digit character is scrolled increase decrease the reference value of the selected parameter inthe Operate menu will cause the display of the active reference source and value and allow its change if the keypad is the active refere
Download Pdf Manuals
Related Search