FX2NC-ENET-ADP Ethernet adapter USER`S MANUAL
Contents
1. eee Note Concerning the Cr Marking E PEES 3 1 How to Install to FX Series PLC 5 Product Specification e marking does not guarantee that an entire mechanical module produced in i a 9 MITSUBISHI Ch forthe Beit accordance with the contents of the notification comply with the following standards ee ce Installation to 5 1 Specifications AE ae lia ad ee Orie entire mechanical module should pe grecked Oy oe z ETE ERATA FX1S FX1N FX2N The general specifications of FX2NC ENET ADP are same as those of the FX PROGRAMMABLE CONTROLLERS Standards with which this product complies 1 Remove the panel cover from the top S P OEP ee MELSEG F Type Programmable Controller Open Type Equipment face of the main unit Withstand voltage OOV AC for 1 min Conforms to JEM 1021 between all terminals together Models Products manufactured from April 1st 2004 A a ce ee enna U S E R S MAN UAL EN61000 6 4 2001 Compliance with all relevant aspects a Se ore i poar iome pon Electromagnetic compatibility of the standard Radiated Emissions 2 Z Corresponding nam Board name model 2 Take off the resin cover from the left side of the main unit General specifications 5 MQ or more by Insulation resistance 500V DC megger and grounding terminal Power supply Supply voltage 5V DC 135 mA supplied from PLC specifications current Generic standards Emission standard for and Mains Terminal Voltage Manual Number2. If the configuration data is read correctly the SD LED and RD LED turn off If an error occurs the SD LED and RD LED indicate the error status as shown below SD LED RD LED Description a or or Eamets Ra The contents of data registers in the PLC cannot be read The header ENET cannot be detected A parameter such as IP address Gateway address Subnet mask and TCP port number is invalid Note In case of 1 or 2 the parameters such as IP address Gateway address Subnet mask are incorrect and the default parameters are valid 8 Virtual COM Port VCP Driver Install the virtual COM port driver on the personal computer in which GX Developer is installed and set the properties to the virtual COM port Set the information of the connected PLC IP address and TCP port number as the properties Recommended driver Serial IP by Tactical Software http www tactical sw com Settings in the Serial IP Version 4 1 is shown as an example 1 Set the virtual COM port to be added at Select Ports 2 Set the following items at Configuration Wizard IP Address of Server IP address of the FX2NC ENET ADP Port Number TCP port number Fer Contra Pomel 4 1 Tac rCAL Ei IP Addesr of Servet Port Number h 921580110 D Terai C Tere ih CA Padding Aa TOF Connection COM Pos Options M DT te modem epcape Use these items M DER susu high in the default T DGD akea high settings D Fesme Fled Co
3. H454E4554 ENET to D128 D129 or DLI000 DL1001 2 The first 8 bits used for the IP address and Gateway address must be in the range from 1 to 223 If any number outside this range is used the RD LED will be lit when the FX2NC ENET ADP is turned on and Ethernet communication will not be performed Set numbers from 1 to 223 3 In the following cases and as explained in 2 concerning the Subnet mask data the RD LED will be lit when the FX2NC ENET ADP is turned on an error will occur and Ethernet communication will not be performed The following conditions are expressed in binary form 1 If 1 is set for all bits 2 If O is set for all bits 3 If 1 is set immediately after 0 is set Example 111 11000100 4 The settings of the IP address Subnet mask and Gateway address depend on the customer s network environment For the contents of these parameters see the network administrator 5 The FX2NC ENET ADP searches for the header in the order D1000 D7000 The values described in lowest data resister numbers are set as the Ethernet parameters 7 2 Parameter setting methods Set the Ethernet parameters using either of the following methods through serial communication e Setting using the PLC program e Setting using file registers For each setting example refer to Section 7 3 7 3 Parameter setting examples for FX2NC ENET ADP Two examples of setting the Ethernet parameters for the FX2NC ENET
4. PLC program is used to set the Ethernet parameters The Ethernet parameters for the FX2NC ENET ADP can be set using the program shown below Note In the FX2NC ENET ADP the Ethernet parameters become valid only when the power is turned ON and the setting data is stored in specified data registers In either of the following cases turn off the power of the PLC once and then turn it on again e When a parameter is set for the first time e When the setting of a parameter is changed during operation FX1s M8002 Setting of Header ASCII codes to specify ENET Setting of IP address 192 168 0 110 CO A8 00 6E Setting of Subnet mask 255 255 255 0 FF FF FF 00 Setting of Gateway address 192 1680 1 CoO A8 0001 TCP Port number 1024 FX1N FX2N FX2NC ByMov H454E4554 D1000 M8002 Setting of Header ASCII codes to specify ENET Setting of IP address 192 168 0 110 CO A8 00 6E BYMOV HCOA8006E D1002 Setting of Subnet mask 255 255 255 0 FF FF FF 00 ByMov HFFFFFFOO D1004 Setting of Gateway address 192 168 041 CoO A8 0001 TCP Port number 1024 ByMov HC0A80001 D1006 6 When connecting two or more PLCs to a network do not use the same IP address twice Example Personal computer GX Developer 192 168 0 10 192 168 0 110 111 PLC2 192 168 0 When file registers are used to set the Ethernet parameters
5. in 2 concerning the Subnet mask data the RD LED will be lit when the FX2NC ENET ADP is turned on an error will occur and Ethernet communication will not be performed The following conditions are expressed in binary form 1 If 1 is set for all bits 2 If O is set for all bits 3 If 1 is set immediately after 0 is set Example 111 11000100 4 The settings of the IP address Subnet mask and Gateway address depend on the customer s network environment For the contents of these parameters see the network administrator 5 The FX2NC ENET ADP searches for the header in the order D1000 D7000 The values described in lowest data resister numbers are set as the Ethernet parameters 7 2 Parameter setting methods Set the Ethernet parameters using either of the following methods through serial communication e Setting using the PLC program e Setting using file registers For each setting example refer to Section 7 3 7 3 Parameter setting examples for FX2NC ENET ADP Two examples of setting the Ethernet parameters for the FX2NC ENET ADP are shown below Example of parameter settings Data register Parameter Set data FXS FX1N FX2N FX2NC D128 D129 D1000 D1001 ENET H454E4554 D130 D131 D1002 D1003 IP address 192 168 0 110 HCOA8006E D132 D133 D1004 D1005 Subnet mask 255 255 255 0 HFFFFFFOO D134 D135 D1006 D1007 Gateway address 192 168 0 1 HC0A80001 D136 D1008 TCP port number 1024 K1024 When the
6. or less lt H ee oe EF cii MITSUBISHI 909000090 ik 899690900 EARI WELSECFXa 32MR o 89 88h5H4 FT ORES 60000000 7 Parameter Settings for FX2NC ENET ADP To connect the FX2NC ENET ADP to the Ethernet it is necessary to set the Ethernet parameters including the Header IP address Subnet mask Gateway address and TCP port number Set the Ethernet parameters to the D data registers in the PLC Immediately after the power is turned on the FX2NC ENET ADP reads the Ethernet parameters stored in the D data registers in the PLC and configures itself 7 1 Used devices FX1s Set the Ethernet parameters to nine data registers from D128 to D136 F Default Description D128 D129 Header o gt o Set H454E4554 ENET D130 D131 IP address 192 168 0 100 Set the IP address for connecting to Ethernet 2 D132 D133 Subnet mask 255 255 255 0 Set the sub net mask for connecting to Ethernet 8 D134 D135 Gateway 192 168 0 1 Set the gateway address for connecting to Ethernet 2 address 4 TCP port Set the TCP ports within the Diae es range from 1024 to 65535 FX1N FX2N FX2NC Set the Ethernet parameters to nine data registers from D1000 to D1008 If these data registers are used for any other purpos
7. unit 3 Install the following board to the port on the main unit Corresponding FX1N CNV BD FX1S FX1N 4 Affix the above board using the supplied M3 screws Tightening torque 0 3 to 0 6 Nem 5 Connect the built in cable of the FX2NC ENET ADP to the port on the left side of the board N Installation to FX1S FX1N FX2N Installation to FX2NC Installation to FX2NC Turn OFF the PLC before beginning any work 1 Remove the cover from the special adapter port provided on the left side of the main unit 2 Connect the built in cable of the FX2NC ENET ADP to the special adapter port 3 2 Installation to a Panel Face Direct installation to the panel face Directly attach to the panel face using 2 sets of a screw M4 a spring washer and a flat washer in the mounting holes Tightening torque 0 7 to 1 0 Nm For the pitch and positions of mounting screw holes refer to the external dimensions Mounting on DIN rail Affix the FX2NC ENET ADP to the DIN rail DIN46277 35 mm 1 37 wide Dismounting from DIN rail Slightly pull down the DIN rail mounting clip using a tool such as a slotted screwdriver Pull down the clip further and the rail will be locked with the clip left open ssa Vv SSe Detach To lock the tab 4 System Configuration FX2NC ENET ADP VFX1S FX1N FX2N LAN cables Ethernet adapter LAN cable FX1S FX1N PLC FX1N CNV BD f T
8. 55 0 FF FF FF 00 ByMov HFFFFFFOO D1004 Setting of Gateway address 192 168 0 CO A8 0001 TCP Port number 1024 ByMov HCoA80001 D1006 6 When connecting two or more PLCs to a network do not use the same IP address twice Example Personal computer GX Developer 192 168 0 10 192 168 0 110 111 PLC2 192 168 0 When file registers are used to set the Ethernet parameters Select Parameter PLC parameter Memory capacity in GX Developer and set the file register capacity to 1 block or more Then right click Device memory add the device memory data and set the parameters as shown below e Settings of D128 to D135 or D1000 to D1007 32 bit HEX mode Devine Label O00 OOO oe A ARs eer cre gilea iLe a mni cme e T Header ENET Subnet mask Gateway address IP address 192 168 0 110 255 255 255 0 192 168 0 1 e Settings of D136 or D1008 16 bit DEC mode N Ly Device Label D 1000 Digia Gsen wc m Dobe pence nent u j 2 enih iho for fenoraeeer zerana monoa ppap aTa z i tbaezi6 Tes pues al ol ol ln TCP port number 1024 7 4 Check of configuration using SD LED and RD LED The SD LED and the RD LED can be used to check whether the current configuration is functioning properly or not At startup reset After power is turned on the SD LED and RD LED are lit for 2 seconds and the FX2NC ENET ADP reads the configuration data from the PLC
9. ADP are shown below Example of parameter settings Data Dataregister Parameter Set data m eee FX1N FX2N FX2NC D128 D129 D1000 D1001 ENET H454E4554 D130 D131 D1002 D1003 IP address 192 168 0 110 HCOA8006E D132 D133 D1004 D1005 Subnet mask 255 255 255 0 HFFFFFFOO D134 D135 D1006 D1007 Gateway address 192 168 0 1 HC0A80001 D136 D1008 TCP port number 1024 K1024 When the PLC program is used to set the Ethernet parameters The Ethernet parameters for the FX2NC ENET ADP can be set using the program shown below Note In the FX2NC ENET ADP the Ethernet parameters become valid only when the power is turned ON and the setting data is stored in specified data registers In either of the following cases turn off the power of the PLC once and then turn it on again e When a parameter is set for the first time e When the setting of a parameter is changed during operation FX1s M8002 Setting of Header ASCII codes to specify ENET Setting of IP address 192 168 0 110 CO A8 00 6E Setting of Subnet mask 255 255 255 0 FF FF FF 00 Setting of Gateway address 192 168 0 1 CO A8 0001 TCP Port number 1024 FX1N FX2N FX2NC By Mov H454E4554 D1000 M8002 Setting of Header ASCII codes to specify ENET Setting of IP address 192 168 0 110 CO A8 00 6E ByMOV HCOA8006E D1002 Setting of Subnet mask 255 255 2
10. JY997D12301 Industrial environment Emissions a EN61131 2 1994 Programmable controllers Compliance with all relevant aspects Revision B A11 1996 Equipment requirements and of the standard RF Immunity Fast D July 2004 tests transients ESD and Damped a12 2000 oscillatory wave FX1N CNV BD FX1S FX1N Installation to FX2NC This manual contains text diagrams and explanations which guide the EN61000 6 2 2001 _ She see et ae ee 4 Affix the above board using the CSMA CD IEEE802 3 reader in the correct installation and operation of the FX2NC ENET ADP Electromagnetic compatibility _ transients ESD Conducted Surges supplied M3 screws Ethernet adapter It should be read and understood before attempting to use Generic standards Immunity for industrial Bower magnetic fields Voltage dips Tightening torque 0 3 to 0 6 N m Performance 10BASE T the unit environments and Voltage interruptions 5 Connect the built in cable of the specifications TO Sae If i doub Ar any Sage nt the installation or AANE NETAN conau a For more details please contact the local Mitsubishi Electric sales site FX2NC ENET ADP to the port on the left side of the board professional electrical technician who is qualified and trained to the local Notes for compliance to the EMC reaulation C ati 5 f ommunication and national standards which apply to the installation site It is neccesary install the EX2NC ENET ADP module in a shiel
11. Nc ENET ADP sends a response program Clear the check box Memory capacgy Device PLc name vo assignment PEC system T P Refer to the PING command described below Operate ae ey Hosea be RESEN tag w cleared wee communication en eveloper transfer the program to the communication board setting parameters and D8120 values in the PLC must be cleard upon program transfer Executing the PING command Open the MS DOS prompt command prompt in the Windows2000 XP Braet In the example above the IP address is set to 192 168 0 110 7 r5 Bonto lime PING 192 168 0 110 afa MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE MITSUBISHI DENKI BLDG MARUNOUTI TOKYO 100 8310 HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN a MITSUBISHI PROGRAMMABLE CONTROLLERS MELSEG F FX2NC ENET ADP Ethernet adapter USER S MANUAL Manual Number JY997D12301 freon TB This manual contains text diagrams and explanations which guide the reader in the correct installation and operation of the FX2NC ENET ADP Ethernet adapter It should be read and understood before attempting to use the unit If in doubt at any stage of the installation of FX2NC ENET ADP consult a professional electrical technician who is qualified and trained to the local and national standards which apply to the installation site If in doubt about the operation or use of the FX2NC ENET ADP please consult the
12. OWER LED ON Yes No Check if FX2Nc ENET ADP and HUB are connected correctly Check if power of HUB is ON Yes Two seconds after FX2NC ENET ADP is turned ON Yes Check Ethernet parameters No For details refer to 7 Parameter Settings for FX2Nc ENET ADP Parameters are read correctly from PLC Are FX2Nc ENET ADP and PLC connected correctly Yes s communication port set for computer link or no protocol communication Value other than 0 Yes Clear communication parameter check box and download program Clear the check box FX parameter Operate If the box is not checked the parameters will be cleared I communication hen Gx Developer transfer the program to the communication board setting parameters and D8120 values in the PLC must be cleard upon program transfer Protocol E m Ustalenati HAE Pent Bantal made F Gortraline 9 Settings in GX Developer 9 1 Setting method Select Online Connection setup PC side I F Serial setting and select a COM port set in the Serial IP PC side I F Serial setting Ea COM pon z Transmission speed 9 6Kbps ki Cancel Setup Select a COM port Connection Sr tup PC side IF IE iin Serial NET IO H NET I CC Link board board board COM COM 3 Transmission speed 3 6Kbps PLC side I F PLC MNET IO H MNE
13. Select Parameter PLC parameter Memory capacity in GX Developer and set the file register capacity to 1 block or more Then right click Device memory add the device memory data and set the parameters as shown below e Settings of D128 to D135 or D1000 to D1007 32 bit HEX mode Devine Label H1000 hh A moe ole N vaio aa at ew X An ire eam ee Subnet mask Gateway address ca Header ENET IP address 192 168 0 110 255 255 255 0 192 168 0 1 e Settings of D136 or D1008 16 bit DEC mode Ly Deka Lat Pm Dipa Gee sD DEC bD Device nome o 2 z a a s a 7 character string pono ppap 17742 a apiszia mM a n n rll ri ia m iih ri TCP port number 1024 7 4 Check of configuration using SD LED and RD LED The SD LED and the RD LED can be used to check whether the current configuration is functioning properly or not At startup reset After power is turned on the SD LED and RD LED are lit for 2 seconds and the FX2NC ENET ADP reads the configuration data from the PLC If the configuration data is read correctly the SD LED and RD LED turn off If an error occurs the SD LED and RD LED indicate the error status as shown below 1 e of data registers in the PLC cannot be The header ENET cannot be detected 2 OFF ON A parameter such as IP address Gateway address Subnet mask and TCP port number is invalid J Note In case of 1 or 2 the para
14. T II CC Link module module module module Note The Transmission speed setting in GX Developer is ignored 9 2 Operations In GX Developer operations such as upload download monitoring and test of a program are performed in the same way as with serial communication 10 Setting in MX Component 10 1 Setting method Select Programs MELSOFT Application MX Component Communication Setup Utility and select a COM port set in the Serial IP a Conran abion Setup Litility Menu Help Tangid idtiray CESS Connection tast Logica lation number Execute PING command for IP address set to PLC 1 Check again IP address set to PLC 2 Confirm that network address in PLC matches network address in PC 3 Confirm connection of Ethernet between PC and PLC No Any response Yes Confirm that TCP port number set in virtual COM port driver matches TCP port number set in PLC Turn ON power again Is any numeric value other than 0 stored in D8120 No Set 0 to D8120 Turn ON power again Reference The PING command confirms confirmation whether the communication between Ethernet devices using the IP address of TCP IP is possible Execute the PING command from the PC connected to Ethernet and check whether the FX2Nc ENET ADP sends a response Refer to the PING command described below Check if PLC and PC are connected correctly Executing the PING c
15. cates that the identified danger WILL cause physical and Connection Board Describes matters related 1 property damage to the installation of the g b 1 FX2N CNV BD Special Adapter boards 5 ob Connection Board PEHINI 2 B T EBK 2 Indicates that the identified danger could POSSIBLY cause gt 25 i and property damage g For GX Developer and MX Component refer to the operation manual respectively Dismounting from DIN rail i l Slightly pull down the DIN rail mounting clip 2 Outline of Product using a tool such as a slotted screwdriver Pull O D n i TEREA down the clip further and the rail will be locked o gt 7 0 28 3 Indicates a point of further interest or further explanation The FX2NC ENET ADP is an Ethernet adapter of 10BASE T specifications for the aut the cls lei posh Height of screw hole FX1S FX1N FX2N and FX2NC Series eee 74 2 92 The FX2NC ENET ADP enables upload download monitor and test sequence of z 78 3 08 programs via Ethernet from a personal computer GX Developer or MX Component he 3 08 gt and the virtual COM port driver installed DISPOSAL PRECAUTIONS Detach To lock the tab 1 Pe E N eden eee ae e When disposing of this product treat it as industrial waste 3 Installation 4 System Configuration Noticed when the nodule is mounted on DIN rail Caution J UN 2 POWER LED green INSTALLATION PRECAUTIONS e Use only in the environments specified under the general specifications a
16. ded metal control Installation to FX2NC method Full duplex If in doubt about the operation or use of the FX2NC ENET ADP please panel Turn OFF the PLC before beginning any work consult the nearest Mitsubishi Electric distributor l f To Ethernet RJ45 connector This manual is subject to change without notice 1 Associated Manuals 1 Remove the cover from the special adapter port provided on the left side of the E i F j j Connector Microsoft Windows is either registered Tactical or trademarks of Microsoft PROGRAMMING MANUAL Il wi included with th duct main unit 3 pins Corporation in the United States and or other countries ar G J menoned be se HOr INE uge K ee 2 Connect the built in cable of the FX2NC ENET ADP to the special adapter port Terground However internally short circuited If required please consult the Mitsubishi Electric sales site where the product was Tactical Software is a registered trademark and Serial IP is a trademark of h Tactical Software LLC purchased 3 2 Installation to a Panel Face 0 1 kg 0 22 Ibs Directly attach to the panel face using 2 sets of a FX1S HARDWARE MANUAL J 992D83901 screw M4 a spring washer and a flat washer Guideline for the safety of the user and protection of the FX2NC ENET ADP FX1N HARDWARE MANUAL JY992D89301 Describes the hardware of in the mounting holes This manual provides usage information for the FX2NC ENET ADP Ethernet Tightening torque 0 7 to 1 0 Nm Th
17. e the Ethernet parameters can be set to nine data registers D starting from D2000 D3000 D4000 D5000 D6000 or D7000 pee rone sen AERE DO000 DH001 Header fo Set H454E4554 ENET DO002 D0003 IP address 192 168 0 100 Set the IP address for connecting to Ethernet 2 Do1004 D0005 Subnet mask 4 255 255 255 0 Set the sub net mask for connecting to Ethernet 3 Gateway Set the gateway address for PENOSA address 4 Be OBM connecting to Ethernet 2 TCP port Set the TCP ports within the pugag et range from 1024 to 65535 Indicates any number in the range from 1 to 7 e If ENET is not found or the parameters such as IP address Gateway address Subnet mask are incorrect the default parameters are valid e f FX2NC ENET ADAP cannot read out the specified data register stored in the PLC the default parameters are used In such a case the SD or RD LED is lit Refer to 7 4 Note 1 This is the header identifier required when FX2NC ENET ADP identifies the Ethernet parameters Make sure to set H454E4554 ENET to D128 D129 or DLI000 DL1001 2 The first 8 bits used for the IP address and Gateway address must be in the range from 1 to 223 If any number outside this range is used the RD LED will be lit when the FX2NC ENET ADP is turned on and Ethernet communication will not be performed Set numbers from 1 to 223 3 In the following cases and as explained
18. e company name and the product name described in this manual are the registered trademarks or trademarks of each company 5 2 Outside dimensions and name of each part 16 1 0 64 Unit inch to screw holes nit mm inches adapter The manual has been written to be used by trained and competent FX2N HARDWARE MANUAL JY992D66301 the i Series PLC such gt For the pitch and positions of mounting screw T personnel Spec ications Wing an holes refer to the external dimensions DA FX2NC HARDWARE MANUAL installation 2 Notes on the symbols used in this manual DSS DS JY992D76401 5 x At various times throughout out this manual certain symbols will be used to D UL JY992D87201 fess 3 jo Le ga highlight points of information which are intended to ensure the users personal Mounting on DIN rail o 7 7 ra safety and protect the integrity of equipment Whenever any of the following Describes the instructions Affix the FX2NC ENET ADP to the DIN rail SO 7 A 5 symbols are encountered its associated note must be read and understood Each PROGRAMMING MANUAL II JY992D88101 available in the FX1S FX1N DIN46277 35 mm 1 37 wide we 5 5 of the symbols used will now be listed with a brief description of its meaning FX2N FX2NC Series PLC z 5 Hardware Warnings D 9 s FX1N CNV BD Special Adapter JY992D84701 i 9 2 1 Indi
19. e of Product The FX2NC ENET ADP is an Ethernet adapter of 10BASE T specifications for the FX1S FX1N FX2N and FX2NC Series The FX2NC ENET ADP enables upload download monitor and test sequence of programs via Ethernet from a personal computer GX Developer or MX Component and the virtual COM port driver installed 3 Installation Caution e Use only in the environments specified under the general specifications in the manual Do not use the product in environments with excessive or conductive dust corrosive including salt breeze Cl2 H2S SO2 NO2 etc or flammable gas oily smoke moisture or rain excessive heat regular impact shocks or excessive vibration as it may result in electrical shock fire malfunction damage or deterioration of the product e Make sure to shut off the external power before installing or wiring it Electric shock or serious damage to the product may occur if the external power is not disconnected e Never drop wire chips or shavings into the ventilation slits when drilling screw holes or performing wiring as they may cause fire breakdown or malfunction e Securely install the FX2NC ENET ADP to the designated port A poor connection may result in malfunction 3 1 How to Install to FX Series PLC Installation to FX1S FX1N FX2N Turn OFF the PLC before beginning any work 1 Remove the panel cover from the top face of the main unit 2 Take off the resin cover from the left side of the main
20. el Enter a comment Back Li Conmanicstion Setup Utility Finish Jh Hanu Help Target setting List view Connection test Fim DTR RTS sfa MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE MITSUBISHI DENKI BLDG MARUNOUTI TOKYO 100 8310 HIMEJI WORKS 840 CHIYODA CHO HIMEuI JAPAN
21. en disposing of this product treat it as industrial waste INSTALLATION PRECAUTIONS e Use the module in an environment that meets the general specifications contained in this manual Using this module in an environment outside the range of the general specifications could result in electric shock fire erroneous operation and damage to or deterioration of the product e Do not disassemble or modify the module Doing so may cause failure malfunction injury or fire gt e OFF TRANSPORTATION AND MAINTENANCE PRECAUTIONS e During transportation avoid any impact as the module is a precision instrument Doing so could cause trouble in the module e It is necessary to check the operation of module after transportation in case of any impact damage Note Concerning the CE Marking The CE marking does not guarantee that an entire mechanical module produced in accordance with the contents of the notification comply with the following standards Compliance to EMC standards of the entire mechanical module should be checked by the user manufacturer Standards with which this product complies Type Programmable Controller Open Type Equipment Models Products manufactured from April ist 2004 Electromagnetic Compatibility Standards EMC EN61000 6 4 2001 Compliance with all relevant aspects Electromagnetic compatibility of the standard Radiated Emissions Generic standards Emission standard for and Mains Terminal Voltage I
22. ie Lit while 5V DC power is supplied from the PLC e Use the module in an environment that meets the general in the manual 3 LINK LED green specifications contained in this manual Using this module in an Do not use the product in environments with excessive or conductive Lit while the HUB is connected by an RJ45 connector and the power is on environment outside the range of the general specifications could dust corrosive including salt breeze Cl2 H2S SO2 NO2 etc or 4 ACT LED red result in electric shock fire erroneous operation and damage to or flammable gas oily smoke moisture or rain excessive heat regular Lit while transferring data with connected Ethernet deterioration of the product impact shocks or excessive vibration as it may result in electrical shock LAN 5 SD LED red e Do not disassemble or modify the module Doing so may cause Bie tia mum Hon damage Or GelenOrstlong Me produet o cables gt pr Rete S Sener seeS eee stee Lit while sending data to the connected PLC failure malfunction injury or fire e Make sure to shut off the external power before installing or wiring it 6 RD LED red Electric shock or serious damage to the product may occur if the external f re f power is not disconnected Lit while receiving data from the connected PLC TRANSPORTATION AND MAINTENANCE PRECAUTIONS i is Never drop wire chips or shavings into the ventilation slits when drilling Ethernet adapter LAN cable 7 Connect
23. ing cable a During transportation avoid any impact as the module is a precision screw holes or performing wiring as they may cause fire breakdown or Used to connect the main unit instrument Doing so could cause trouble in the module malf netion FX1S FX1N PLC FX1N CNV BD a 8 RU45 connector e It is necessary to check the operation of module after transportation wisted pair cable he Eth le in case of any impact damage Securely install the FX2NC ENET ADP to the designated port FX2N PLC FX2N CNV BD FX2NC ENET ADP Category 5 e STP or 3 Connects t e Ethernet cane A poor connection may result in malfunction 9 Terminal block for grounding EX2NG PLC STP straight cable 2 Internally short circuited Applicable cable AWG 17 to 14 e Compatible version of GX Developer Tightening torque 0 4 to 0 5 Nem Ver 8 12N or later 10 DIN rail mounting hook e Compatible version of MX Component 11 DIN rail mounting groove Ver 3 05F or later 5 3 Connector pin arrangement The RJ45 connector in the FX2NC ENET ADP has the following pin arrangement Pin Signatname Direction Description a o m fps orreceve aa ee ae ie ee ae ee o mws e S ra ma E 5 4 Used cable STP Shielded twisted pair cable Category 5 e or 3 6 Wiring 6 1 Cautions on wiring Wiring Precaution e Cut off all phases of external power source before installation or performing wiring work in order to avoid electric shock or damage to the prod
24. mask 255 255 255 0 Set the sub net mask for connecting to Ethernet 3 D134 D135 Gateway 192 168 0 1 Set the gateway address for connecting to Ethernet 2 address 4 TCP port Set the TCP ports within the piss Ipea range from 1024 to 65535 FX1N FX2N FX2NC Set the Ethernet parameters to nine data registers from D1000 to D1008 If these data registers are used for any other purpose the Ethernet parameters can be set to nine data registers D starting from D2000 D3000 D4000 D5000 D6000 or D7000 Default D000 D0001 DO001 Header fo Set H454E4554 ENET po002 D00003 IP address 192 168 0 100 Set the P address for connecting to Ethernet 2 DO004 D0005 Subnet mask 255 255 255 0 Set the sub net mask for connecting to Ethernet 3 Gateway Set the gateway address for address 4 132a connecting to Ethernet 2 TCP port Set the TCP ports within the pus et range from 1024 to 65535 Indicates any number in the range from 1 to 7 D006 D007 e If ENET is not found or the parameters such as IP address Gateway address Subnet mask are incorrect the default parameters are valid e f FX2NC ENET ADAP cannot read out the specified data register stored in the PLC the default parameters are used In such a case the SD or RD LED is lit Refer to 7 4 Note 1 This is the header identifier required when FX2NC ENET ADP identifies the Ethernet parameters Make sure to set
25. meters such as IP address Gateway address Subnet mask are incorrect and the default parameters are valid 8 Virtual COM Port VCP Driver Install the virtual COM port driver on the personal computer in which GX Developer is installed and set the properties to the virtual COM port Set the information of the connected PLC IP address and TCP port number as the properties Recommended driver Serial IP by Tactical Software http www tactical sw com Settings in the Serial IP Version 4 1 is shown as an example 1 Set the virtual COM port to be added at Select Ports 2 Set the following items at Configuration Wizard IP Address of Server IP address of the FX2NC ENET ADP Port Number TCP port number Fer Contra Pomel 4 1 aa Tac rCAL IP dder of Saret h 921580110 C Takai mih CE Paddrg Aa TOF Connection COM Poa Options DTR emeden arcane Use these items in the default M DOD skeyt high settings D Fesme Fled Connections Select a COM port 1 Set the TCP Set the IP address port number _ Conte ucstion izad COMI r Tes lor presence o a poder connecked bo the aee Shakur Lox EAEE sauces omen 5 Note Make sure that the IP address and TCP port number set in the Serial IP are equivalent to the Ethernet parameters set in the PLC 11 Troubleshooting Turn ON power of PLC No Check the cable connection between FX2NC ENET ADP and PLC Is P
26. n ON power of PLC Is POWER No LED ON Check the cable connection between FX2NC ENET ADP and PLC Yes No Check if FX2Nc ENET ADP and HUB are connected correctly Check if power of HUB is ON Yes Two seconds after FX2NC ENET ADP is turned ON Execute PING command for IP address set to PLC 1 Check again IP address set to PLC No 2 Confirm that network address in PLC Any response matches network address in PC 3 Confirm connection of Ethernet between PC and PLC Yes Yes Yes Confirm that TCP port number set in virtual Chee Eiheme COM port driver matches TCP port number parameters No For details refer to 7 Parameter Parameters are read correctly set in PLC Are FX2Nc ENET ADP and PLC connected correctly Settings for FX2NC ENET _ from PLC ADP Yes Turn ON power again Is any numeric value other than 0 stored in D8120 s communication port set for computer link or no protocol communication Value other than 0 stored in D8120 No Yes Clear communication parameter check box Set 0 to D8120 and download Check if PLC and PC Turn ON power again are connected correctly Reference FORSA The PING command confirms confirmation whether the communication between Ethernet devices using the IP address of TCP IP is possible Execute the PING command from the PC connected to Ethernet and check whether the FX2
27. ndustrial environment Emissions EN61131 2 1994 Programmable controllers Compliance with all relevant aspects A11 1996 Equipment requirements and of the standard RF Immunity Fast tests transients ESD and Damped A12 2000 oscillatory wave Compliance with all relevant aspects of the standard RF immunity Fast transients ESD Conducted Surges Power magnetic fields Voltage dips and Voltage interruptions EN61000 6 2 2001 Electromagnetic compatibility Generic standards Immunity for industrial environments For more details please contact the local Mitsubishi Electric sales site Notes for compliance to the EMC regulation It is necessary to install the FX2NC ENET ADP module in a shielded metal control panel 1 Associated Manuals PROGRAMMING MANUAL II mentioned below is not included with the product If required please consult the Mitsubishi Electric sales site where the product was purchased ee oa Describes the hardware of specifications wiring and FX2NC HARDWARE MANUAL JY992D76401 installation a JY992D87201 PROGRAMMING MANUAL II Describes the instructions JY992D88101 available in the FX1S FX1N FX2N FX2NC Series PLC FX1N CNV BD Special Adapter Connection Board JY992D84701 Describes matters related to the installation of the FX2N CNV BD Special Adapter Connection Board Jy992D63601 boards For GX Developer and MX Component refer to the operation manual respectively 2 Outlin
28. nearest Mitsubishi Electric distributor This manual is subject to change without notice Microsoft Windows is either registered Tactical or trademarks of Microsoft Changes for the Better Corporation in the United States and or other countries Tactical Software is a registered trademark and Serial IP is a trademark of Tactical Software LLC The company name and the product name described in this manual are the registered trademarks or trademarks of each company Guideline for the safety of the user and protection of the FX2NC ENET ADP This manual provides usage information for the FX2NC ENET ADP Ethernet adapter The manual has been written to be used by trained and competent personnel Notes on the symbols used in this manual At various times throughout out this manual certain symbols will be used to highlight points of information which are intended to ensure the users personal safety and protect the integrity of equipment Whenever any of the following symbols are encountered its associated note must be read and understood Each of the symbols used will now be listed with a brief description of its meaning I o Q o oO o gt gt Q 7 1 Indicates that the identified danger WILL cause physical and property damage 2 Indicates that the identified danger could POSSIBLY cause physical and property damage 3 Indicates a point of further interest or further explanation DISPOSAL PRECAUTIONS e Wh
29. nnections Select a COM port Set the TCP Set the IP address port number Conii uestion Wizard COMI r Tes lor presence o a poder connecked bo the aee Shakur Lox EAEE sauces omen 5 Note Make sure that the IP address and TCP port number set in the Serial IP are equivalent to the Ethernet parameters set in the PLC 9 Settings in GX Developer 9 1 Setting method Select Online Connection setup PC side I F Serial setting and select a COM port set in the Serial IP PC side I F Serial setting Ea COM at Transmission speed 9 6Kbps z Cancel Setup Select a COM port Connection Sr tup PC side I F Serial NET IO H NET I CC Link board board board COM COM 3 Transmission speed 3 6Kbps PLC side I F PLC MNET IO H MNET II CC Link module module module module Note The Transmission speed setting in GX Developer is ignored 9 2 Operations In GX Developer operations such as upload download monitoring and test of a program are performed in the same way as with serial communication 10 Setting in MX Component 10 1 Setting method Select Programs MELSOFT Application MX Component Communication Setup Utility and select a COM port set in the Serial IP a Conran abion Setup Litility Menu Help Tangid idtiray CESS Connection tast Logica Staton number Qe Communication Setting Wiza
30. ommand Open the MS DOS prompt command prompt in the Windows2000 XP In the example above the IP address is set to 192 168 0 110 PING 192 168 0 110 Communication Setting Wizard Introduction x This Communication Setting Wizard will set the communication information for ACT You can press Back at any time to change your selections Please click Next to begin Please select the logical station number Logical station number Finish Select the Logical station number before clicking the Next button Next Select Serial Communication Setting Wizard PC side 4 x Please select the PC side IF PC side IF Communication setting Connect port Time out 10000 ms Select a COM port Next Select CPU module Communication Setting Wizard PLC side g xj Cancel Please select the PLC side IF PLC side IF Communication setting CPU type FX2NC z Transmission speed Control Cancel Note FX1S FX1N FX2N C The Transmission speed setting in MX Component is ignored non SI Select Host station Communication Setting Wizard Network x Please select the Network Station type Host station Communication Setting Wizard Finished i x The Communication wizard has finished collecting information Please Finish to build the logical station number Comment via FX2NC ENET ADP Canc
31. rd Introduction x This Communication Setting Wizard will set the communication information for ACT You can press Back at any time to change your selections Please click Next to begin Please select the logical station number Logical station number Finish Select the Logical station number before clicking the Next button Next Select Serial Communication Setting Wizard PC side 4 x Please select the PC side IF PC side IF Communication setting Connect port Time out 10000 ms Select a COM port Next Select CPU module Communication Setting Wizard PLC side g xj Cancel Please select the PLC side IF PLC side IF Communication setting CPU type FX2NC z Transmission speed Control Cancel Note FX1S FX1N FX2N C The Transmission speed setting in MX Component is ignored non SI Select Host station Communication Setting Wizard Network x Please select the Network Station type Communication Setting Wizard Finished i x The Communication wizard has finished collecting information Please Finish to build the logical station number Comment via FX2NC ENET ADP Cancel Enter a comment Back Li Conmanicstion Setup Utility Finish Jh Hanu Help Target setting List view Connection test Fim DTR RTS 11 Troubleshooting Tur
32. red Lit while transferring data with connected Ethernet 5 SD LED red Lit while sending data to the connected PLC 6 RD LED red Lit while receiving data from the connected PLC 7 Connecting cable Used to connect the main unit 8 RJ45 connector Connects the Ethernet cable 9 Terminal block for grounding Internally short circuited Applicable cable AWG 17 to 14 Tightening torque 0 4 to 0 5 Nem 10 DIN rail mounting hook 11 DIN rail mounting groove 5 3 Connector pin arrangement The RJ45 connector in the FX2NC ENET ADP has the following pin arrangement Pin Sianal name Direction Description CAm E i ee ae ee eee of oe E E e a 5 4 Used cable STP Shielded twisted pair cable Category 5 e or 3 6 Wiring 6 1 Cautions on wiring Wiring Precaution A e Cut off all phases of external power source before installation or performing wiring work in order to avoid electric shock or damage to the product Wiring Precaution e The grounding terminal in the main unit should be connected to a grounding resistance of 100Q or less e Do not drop cuttings and wire chips into the ventilation slits of the PLC when drilling screw holes or performing wiring work Otherwise fire failure or malfunction may occur Another equipment Another Another equipment equipment Common grounding Dedicated grounding Shared grounding good best not possible PLC 6 2 Wiring example Grounding 100Q
33. uct Wiring Precaution AN e The grounding terminal in the main unit should be connected to a grounding resistance of 100Q or less e Do not drop cuttings and wire chips into the ventilation slits of the PLC when drilling screw holes or performing wiring work Otherwise fire failure or malfunction may occur Another equipment Another Another equipment equipment Common grounding Dedicated grounding Shared grounding good best not possible PLC 6 2 Wiring example Grounding 100Q or less 99999909 Ih 929QQQ999 ot 8988066 od00000 7 Parameter Settings for FK2NC ENET ADP To connect the FX2NC ENET ADP to the Ethernet it is necessary to set the Ethernet parameters including the Header IP address Subnet mask Gateway address and TCP port number Set the Ethernet parameters to the D data registers in the PLC Immediately after the power is turned on the FX2NC ENET ADP reads the Ethernet parameters stored in the D data registers in the PLC and configures itself 7 1 Used devices FX1s Set the Ethernet parameters to nine data registers from D128 to D136 mera Semen ARE D128 D129 D129 Header gt o Set H454E4554 ENET D130 D131 IP address 192 168 0 100 Set the IP address Tor connecting to Ethernet 2 D132 D133 Subnet
34. wisted pair cable FX2N PLC FX2N CNV BD FX2NC ENET ADP Category 5 e STP or 3 STP straight cable FX2NC PLC e Compatible version of GX Developer Ver 8 12N or later e Compatible version of MX Component Ver 3 05F or later 5 Product Specification 5 1 Specifications The general specifications of FX2NC ENET ADP are same as those of the FX Series PLC except the following items Withstand voltage 500V AC for 1 min Conforms to JEM 1021 between all terminals together and grounding terminal aa Performance Transmission media General specifications 5 MQ or more by Insulation resistance 500V DC megger specifications Topology Star type Communication To Ethernet RJ45 connector To ground 3 ping er However internally short circuited 0 1 kg 0 22 Ibs 5 2 Outside dimensions and name of each part 16 1 0 64 to screw holes Connector Unit mm inches 2 4 2 0 17 to center of DIN rail between screw holes ITSUBISHI MQDEY FXeng ENET ADP 7 0 28 Height of screw hole 74 2 92 p 78 3 08 1 Mounting hole 2 4 2 Used when FX2NC ENET ADP is mounted directly Not used when the module is mounted on DIN rail 2 POWER LED green Lit while 5V DC power is supplied from the PLC 3 LINK LED green Lit while the HUB is connected by an RJ45 connector and the power is on 4 ACT LED
Download Pdf Manuals
Related Search