LASER FINDER LM 63A
Contents
1. OPERATION CAUTION e For reasons to protect the electric circuits of the laser device and for reasons due to the prolongation of its life brightening of the beam which takes approx 5 minutes was started in model year 2001 e The life of the laser is limited to approx 2000 working hours During this period the intensity of the beam may weaken e Before connecting it to electric power shift the switch into the Off position see fig further in the text e lf the switch were in the On position the laser would begin to emit radiation with a delay of approx 5 sec this is why you have to make sure it can not reach contact with eyes of persons or animals directly or via reflected beam e Place the stand in a convenient position with the head in the required position e Start the device by shifting the switch into the On position o Instructional diagrams Switch position On Switch position Off Output 5 V from the adapter connected to the connector of the rear side of the laser head To connect the adapter to the electric power use the adapter Rotating the radiated beam can only be done once the head has been installed by releasing the stopping screw white arrow on the cover of the head and by rotating the output grooved cylinder yellow arrow Once the beam direction has been setup secure the position by tightening the stopping screw slightly e Forms of use Keep your device clean Dirt from tools m2. We will do our best to address Report and maintenance report your comment or question in timely matter Before first use please read this manual carefully It is your responsibility to study all instructions SERVICE SHOP necessary for safe use and operation and to understand all risks that may be involved during the use of power machines WARNING Do not try to use this machine before reading this entire manual and before you know how to handle it Keep this manual for future reference Pay special attention to safety instructions Not complying with safety rules may cause injury to the operating person or to people standing by or it may cause damage to the machine or to the work piece Pay special attention to safety notes and safety labels on the machine Never remove or damage them Please write information such as the invoice number and the number of the sale receipt here in this box DESCRIPTION Use of laser in production and assembly brings significant savings in the scope of determining the exact position of the part For example on saws you can determine the cut path and hence optimise the through cut On milling cutters or flame cutting devices lasers enable quick cheap and precise setup of work pieces in the outout position At present when the price of lasers is affordable with their help it is possible to improve the quality and work tempo of every workshop or at assembly sites A protective circuit is installed which bri
3. warranty period will be extended for the period of time for which the machine has been in the service centre possession If the repair or defect is not covered by the warranty policy all costs including the repair and shipping will be paid by the owner of the machine tool We recommend sending the machine in its original packaging Please also enclose brief description of the defect with the packaging 7 Before sending the machine for repair clean it thoroughly If the received machine is dirty it may be rejected by the service shop or you may be charged a cleaning fee SERVICE Logistic centre Klecany Topolova 483 250 67 Klecany Czech Republic Claim department phone number 266 190 156 T mobile 603 414 975 266 190 111 O2 601 218 255 Fax 260 190 100 Vodafone 608 227 255 http www KHnet cz Email servis KHnet cz Product LASER FINDER LM63A Type Im63A Serial number product series Date of manufacture Repair centre notes Date of sale stamp signature _ mean Without the correctly filled warranty card or without proof of purchase receipt including the product type invoice purchase receipt no warranty claim will be processed Dear customer Thank you for purchasing equipment from KH Trading s r o Our company is ready to offer you our services before during and after you buy our product REPAIR AND MAINTENANCE REPORT If you have any question comment or idea please contact our business centre
4. WARRANTY CARD 1 KH Trading machines and tools are covered by 6 24 months warranty starting on the date of purchase as described in the Civil Code proof of purchase or invoice receipt must be enclosed with the warranty card when making a claim 2 This warranty does not cover defects caused by unprofessional handling machine overloads not complying with instructions contained in this manual using accessories that are not approved unauthorized repair regular wear and tear and damages occurred during transport Further this warranty does not cover parts and accessories such as the motor carbon brushes seals and hot air operated parts and parts that need to be changed regularly 3 Ifthe repair is to be found as not covered by the warranty policy all costs including the repair and ship L A S E Fe fe Ni D a Re ping to and from the repair centre will be paid by the customer according to valid price list See www 4 When making a claim you must present the warranty card showing the date of the purchase the serial number of the machine vendor stamp and signature of sales clerk as well as the proof of IL pA 6 3 A purchase receipt 5 Warranty claim shall be made at the vendor shop where you bought your machine or you may mail it to a service centre The vendor is obligated to fill out the warranty card date of sale serial number vendor stamp and signature All these information must be filled in at the time of sale 6 The
5. ay enter the inner device mechanism and cause damages to the device e Do not use aggressive cleaning solution or paint thinners to clean your device e Clean plastic parts with soft cloth dipped in soapy water e lf you are not using your device lubricate it with suitable grease and store it in a dry place to prevent corrosion i Detailed description of the use of this device is not included in this manual because the manufacturer distributor assumes that the user is experienced in similar type of work Also according to the applicable law this device is considered as a commonly sold and used tool If the user is unfamiliar with the use of this device we recommend finding out more information about using this device at the Department of work safety
6. connecting the power supply cable make sure that the main switch is in the Off position When you finished your work disconnect the power plug from the wall outlet and switch off the main switch e Never carry electric power tools and equipment by their cable o When disconnecting the plug from the wall outlet never pull the cable by its cord e Protect the power cable from high temperatures oils paint thinners and make sure that the cable is not hanging over sharp edges e Inspect the power cable regularly If damaged have it replaced by qualified technician Inspect extension cables regularly If damaged have it replaced e If you need to use an extension cable use cable with appropriate power rating Use only completely unwound Inspect extension cables regularly Damaged cables must be repair immediately e Before performing any maintenance repair or adjustment switch off the main switch and disconnect the power cable from the wall outlet e Do not use in environments where explosives are stored or used paint shops warehouse with flammables etc e Do not use in humid environments or if wet ASSEMBLY e Before throwing the packaging material out make sure no part is left inside If so take it out and install it Use the part listing for check up and the installation drawing for guidance e Before turning on the adapter in the electric power always connect its end to the laser head first See instructional figures hereinafter
7. ersonal injury or damage to the machine or materials AN Caution You are using an electrically powered device Electrical hazard ae Warning Danger of damage i Note Additional information A Laser product Risk of eye injuries AN General instructions e Plastic bags and packaging materials pose danger for small children and animals e Make sure you know your tool or machine and you are familiar with its operating procedure Know the hazards if not used correctly e Person using this machine must be properly trained and must know how to safely operate this equipment He must be also aware of the hazards and risks that may occur if not used correctly e Pay special attention to safety notes and safety labels Do not remove or damage them If the warning label becomes unreadable or damaged please contact your vendor e Maintain your working area clean Disorganized and dirty working area may cause accidents e Never work in tight spaces or in purely lit rooms Make sure the floor is solid and stable and that you can move around easily Maintain stable posture during work e Stay focused and use all your senses Pay attention to the working procedure Do not continue to work if you cannot pay attention e Maintain your tools clean e Handles must be kept free of grease and dirt e Make sure no children unauthorized persons or animals have access to your workshop e Never leave your machine unattended during operatio
8. g facility near you More information about electrical and dangerous waste disposal may be obtained from your local authority or from the Internet If the machine breaks down send it back to the vendor for quick repair Please enclose brief description of the defect That makes repair easier If the machine is still covered by warranty enclose the warranty card and proof of purchase receipt After the warranty period expires we repair your machine for a special price To prevent possible damages during shipping packed the machine carefully or use the original packaging material We are not liable for shipping damages due to incorrect packaging of your machine If making a Claim at the shipping company the level and method of packaging plays a major role during claim evaluation process Note Pictures and contents in this manual may slightly differ from the actual product or accessories It is due to continuous improvement of our products Such small differences have no effect on the product functionality AN Electrical equipment e Observe all basic safety rules when using electrical equipment to prevent risk of fire injuries by electrical shock and other hazards Before using this device read this manual entirely and follow all safety instructions e Make sure the power cable plug is plugged into the correct wall outlet o Make sure the electrical system uses the same voltage as your device Otherwise you may damage your device e Before
9. ghtens the beam within 5 minutes of being turned on TECHNICAL SPECIFICATIONS Voltage external source 230 5 V 50 Hz Current 40 60 mA Power output Wave length Laser category beam width beam shape beam angle Effective range depends on the conditions of light Operation temperature Laser head dimensions Gross weight 2460 abr aen coe b hee eee ea en eee 9 ee es 0 440 kg NEUWSIGIU sasira ately 2a aah oe eh Boe eae a Oe ee ee Oa hk oe wad ek hak ew SO 0 250 kg The accuracy of instructions graphs and information contained herein depends on the printing date Due to continuous product improvement the manufacturer reserves the right to change technical parameters of the product without prior customer notification REVISION REPORT SAFETY PRECAUTIONS The user is obligated to perform tests and revisions of electrical equipment of the machine e This device may be used by a qualified person 18 years or older who has been in accordance with valid rules and regulations Result report trained in work and environmental safety procedures e Any person using this equipment must possess a medical certificate REVISION TECHNICIAN demonstrating his eligibility to operate this equipment Number SIGNATURE We recommend placing warning labels on conspicuous places around your workplace e Prevent most common injuries LASER PRODUCTS Symbols used in this manual A N Warning This symbol informs you about the risk of p
10. n e Use only for purposes for which it has been designed e Do not underestimate your abilities and Know your limits Use both hands e Never work under the influence of alcohol or other drugs e Do not use the machine tool if you feel dizzy or week e Any modifications or improvements to the machine are strictly prohibited DO NOT USE if you discover bent part crack or other damage e Never perform any maintenance during operation e f you see any unusual sign or hear any strange sound switch off your machine and stop working immediately e Before use make sure all screws are tighten securely e Perform maintenance regularly Before use make sure the device is in good working conditions and without any damage e Use only original spare parts during repairs e Using extension pieces or accessories not approved by the manufacturer may cause injuries to the operating personnel e Do not expose to extremely high temperature or direct sunlight e This machine is not design for use in humid environments or under water e if you are not using your machine store it in a dry and safe place out of reach of children e If not stated otherwise in this manual all damaged parts must be repaired or changed A Laser product e Laser product class II EN60825 1 1997 e Due to safety reasons it is strictly prohibited to look directly into the laser beam with bare eyes or using any optical apparatus or lens e Do not aim the laser light at
11. persons or animals Risk of eye injuries e Do not touch the laser lens e Laser pointer is not a toy ae Fine mechanics e Never use vise to hold your tool machine e Protect you device from impact and fall AN Assembly e Do not use the machine unless completely assembled AN High voltage e The head is a very tight unit and contains parts which may never be repaired by the user e The head must be operated without a covering Danger of damage to eyesight and electric shock DISPOSAL When the operational life of your device is over dispose off it in accordance with valid rules and regulations Your product is made of metal and plastic parts that may be recycled when separated 1 Disassemble all parts 2 Separate all parts according to the material they are made of e g metals rubber plastics etc Take the separated parts to the recycling facility near you 3 Electrical waste used electrical power tools electric motors recharging equipment electronics accumulators batteries etc Dear customer In accordance with the valid regional rules and regulations describing the management of electrical waste electrical waste is considered dangerous Disposal of electrical waste must be therefore handled as dangerous waste in accordance with waste management rules valid in the state you are in It is prohibited to mix electrical waste with regular household waste You may return your used electrical appliance to a recyclin
Download Pdf Manuals
Related Search