1 - Family Pool Fun
Contents
1. line 866 730 9880 or email to customersupport smartpool com GENERAL SPECIFICATIONS Calculated Ground Speed 50 ft min 900 m hr Calculated Scanning Rate 63 ft2 min 350 m2 hr Suction Rate 4750 gals hr 18 000 I hr W eight w o cable 20 8 lbs 9 4 kg POWER SUPPLY Primary Voltage 115 VAC Secondary Voltage 29 VDC nominal Rated Output 250 Watts These specifications may vary for different swimming pools and for the various electrical configurations Although the DOLPHIN has been tested in a wide range of swimming pools the manufacturer cannot accept responsibility if the DOLPHIN is not entirely suitable for any particular swimming pool For more details contact SmartPool customer support 866 730 9880 or email to customersupport smartpool com Note The sealed motor unit and the DOLPHIN power supply contain no user serviceable parts Opening these units will automatically void your warranty The manufacturer reserves the right to change these specifications without prior notice U S Patent No 4168557 S A Patent No 76 7474 AUST Patent No 509698 Fig DOLPHIN CADDY ASSEMBLY C 6 Store the Dolphin upright on the Caddy and coil the cable loosely around the Caddy hooks DOLPHIN ASSEMBLY DOLPHIN TROUBLE SHOOTING Symptom Possible reasons Corrective action Air bubbles expelling from impeller tube or Dolphin climbing too high e Remove handle floats amp If necessary attach Dolphin falling backwards a2. 5 p 5 Fig F and remove the bottom lid assembly 6 p 5 Fig G e Remove the 2 black filter bag clips 7 p 5 and the filter bag 8 p 5 Turn the filter bag inside out and wash thoroughly with a garden hose Fig H The bag may be laundered using a regular synthetics cycle This should be done at least once every 2 months An additional filter bag is included Remove the yellow inlet cover 9 p 5 by pulling it gently upwards Remove the inlet flaps 10 p 5 e Clean the inlet flaps cover and under the locking clips e Reinstall the flaps the inlet cover Replace the filter bag with the tag on the outside amp positioned centrally along the long side of the bottom lid Stretch the elastic ring of the bag over the 2 metal frames and over the white lip of the bottom lid Gather all the excess filter material into the center of the metal frames e Gather the material along the top of the frames so that the corners of the bag are adjacent to the corners of the frame Install a black filter bag clip over the top of each frame Fig I Install the bottom lid assembly in the body and lock it in place Before cleaning moving parts ensure power supply is turned off amp unit is unplugged Turn the roller brushes 11 p 5 and remove anything caught under the tracks 12 p 5 Turn the Dolphin over amp remove the yellow impeller tube 13 p 5 by turning it gently counter clockwise Fig J
3. READ CAREFULLY BEFORE USING YOUR DOLPHIN ROBOTIC POOL CLEANER DOLPHIN CADDY ASSEMBLY INSTRUCTIONS Insert the wheel assembly c 1 p 4 firmly into the groove underneath the yellow base ensuring it For DOLPHIN caddy assembly A is centered with a plastic washer c 2 p 4 on each side see page 4 Insert the 2 metal pipes c 3 p 4 into the holes at the top of the white Caddy tower c 4 p 4 until they clip onto the wishbone clips in the studs at the base of the tower Fit the 2 hooks c 5 p 4 to the top of the pipes until they clip into the wishbone clips Fit the top of the handle c 6 p 4 in the upright position see diagram until it clips on the wishbone clips in the hooks Fig A L INSTALLATION The caddy and power supply 1 p 5 should be positioned so that the DOLPHIN can reach all the walls of the swimming pool It must be in the shade and at a minimum distance of 10 ft 3 meters from the edge of the pool Fig B Fig Minimum 3m 10 B a Use only the original DOLPHIN power supply The power supply has been tested and ETL approved to UL1012 standard for outdoor use Do not submerge power supply HANDLE The DOLPHIN features an adjustable handle 2 p 5 that is fitted into slots on each side of the DOLPHIN body This handle must be locked in a diagonal position across the top of the DOLPHIN body in order to ensure optimum cleaning results Press downwards on each yellow latch 3 p 5 to move each hand
4. Remove debris or hair clogged in the impeller 14 p 5 Replace the impeller tube e Change the position of the handle by pressing downwards on the yellow latches and locking the handle in the opposite diagonal position Store the Dolphin upright on the Caddy and coil the cable loosely around the Caddy hooks Fig L Store the Dolphin in a dry shaded place Fig K IM PORTANT TIPS e Clean the filter bag whenever you remove the DOLPHIN from the pool if a bag is left dirty it may become unusable A green clean up filter bag is available for collection of large debris e g leaves Contact your dealer Replace worn brushes 15 p 5 to ensure maximum cleaning performance To prevent the Dolphin from getting stuck on the main drain install a main drain cover Protruding wall fittings e g return outlets for fountains etc may impede the DOLPHIN s lateral movement An additional cleaning cycle with the handle in the reverse diagonal may be necessary to clean entire pool When first used the Dolphin may climb too high and suck in air when it reaches the waterline If so remove the yellow handle fioats by pushing them downward Fig M If the problem continues add a flat weight of approximately 8 oz or as heavy as possible so long as the Dolphin continues to climb the walls to the upper side of the inlet cover For more advice see Trouble Shooting Guide or please contact SmartPool s customer support
5. ition not changed Gets stuck on main drain cover Motors not working Impeller blocked Clean around impeller e Clean tracks wheels Electrical problem motor unit cable Check cable amp wall plugs amp sockets power supply Call Dolphin Support Line Dolphin will not sink Air caught in filter bag Turn Dolphin upside down under water or machine wash filter bag Note Operating the Dolphin out of the water will void warranty Dolphin Customer Support 866 730 9880 M onday to Friday 8 30 to 5 30 Eastern Time or email to customersupport smartpool com 6
6. le arm Fig C To avoid cable coiling and for the most efficient cleaning pattern reverse handle position after each use Fig D OPERATION AVOID ENTERING THE SWIMMING POOL WHILE THE DOLPHIN IS IN OPERATION Connect the cable 4 p 5 to the power supply Properly line up notch and groove push cable in firmly before closing screw collar Place the DOLPHIN in the pool Fig E Rock from side to side releasing trapped air until the DOLPHIN sinks slowly to the bottom of the pool Connect the power supply to a protected grounded outlet and switch on Caution Do not operate the DOLPHIN out of water This may result in extensive damage to the pump motor seals thus voiding the warranty Optimum water temperature for the DOLPHIN is 64 F 90 F 18 C 32 C 113 F 45 C 41 F 5 C AUTOMATIC SHUT DOWN The DOLPHIN will automatically shut down after a work cycle of 12 hours Should a second cycle be required switch off the power supply for at least 30 seconds before restarting SWITCH OFF THE POW ER SUPPLY BEFORE REM OVING THE DOLPHIN FROM THE POOL Caution Surges and interruptions to electric power may cause the DOLPHIN to restart After completing cleaning SWITCH OFF the power supply Pull the Dolphin to the surface by gently pulling the cable e Lift the Dolphin out of the water by the handle NOT THE CABLE Place the Dolphin upside down release the 2 yellow locking clips
7. t waterline 80z weight to bottom inlet cover Change handle diagonal after each use Turn off filter install main drain covering Stralghten cable lay in sun periodically Dolphin moving in circles Dirt stuck in drive system Check tracks are free amp not stretched e Track Is stretched amp or worn e Tracks need replacing Call Dolphin support line e Power supply wrongly positioned e Place power supply in a position so that Dolphin can reach all walls Dolphin is too light e Remove handle floats amp if necessary attach 80z weight to bottom inlet cover Dolphin does not reach all pool areas Power supply wrongly positioned e Place power supply in a position so that Dolphin can reach all walls e Filteris on Turn off pool filter Not traveling sideways along waterline Move handle floats to one side place 8 oz weight in filter bag on other side Dolphin does not climb walls Dolphin too heavy Empty amp wash filter bag amp add floats if necessary Filter bag clogged with fine debris e Machine wash filter bag Algae on walls Brush walls Water temperature too low Water temperature should be above 65 F Water inside handle Call Dolphin Support Line Dolphin too light e Remove handle floats amp attach 80z weight to bottom inlet cover if necessary Debris caught around impeller Untwist impeller tube amp clean impeller e Cable twisting Handle pos
Download Pdf Manuals
Related Search