MANUBAL V40-V50-V500-W500-V7000 instructions
Contents
1. 4 DESCRIPTION Ka amp D gt 2 Grab 3 Tine 4 Ram 5 Synchronising crank 6 Synchronising link 7 Rod end ram pin 8 Cylinder end ram pin DS od LA 7 A Modification reserved MX e 19 rue de Rennes BP 83221 F 35690 ACIGN 5 HITCHING UNHITCHING THE MANUBAL BALE GRAB 5 1 HITCHING THE MANUBAL BALE GRAB 5 1 1 Hookthe self centring V notches into the MANUBAL hitch bar Fig 1 for telescopic handlers refer to the manufacturer s user manual 5 1 2 Position yourself on the right hand side and lock manually Fig 2 5 1 3 Crowd back to check that the MANUBAL is being held correctly Fig 3 5 1 4 Operate each moving componenitoits fullest extentin each direction to check the hydraulic system is free from leaks and the hoses are routed correctly 2 Position for locking the MANUBAL bale grab 3 MX loaders before May 2013 MX loaders after May 2013 Ww s Push with your foot Caution you may be crushed 5 2 UNHITCHING THE MANUBAL BALE GRAB 5 2 1 Remove the MANUBAL unit with the grab open ram rod retracted 5 2 2 Release the hydraulic pressure and unhitch CAUTION for MANUBAL bale grabs fitted with lower tines these should be in the park position see chapters 8 and 10 MX 7 19 rue de Rennes BP 83221 F2. I B e 0 I I 9 2 0 gt e Ges 7 2 a y E a e Optional on MANUBAL V40 V50 W500 MX 7 19 rue de Rennes BP 83221 F 35690 ACIGN Optional on MANUBAL V40 V50 V500 W500 17 Optional on MANUBAL V500 V7000 Stacking helahl 4 bales 5 bales 5 bales 5 bales 6 bales gneg H1 20m H1 20m H1 20m H1 20m H1 20m 2 bales Up to 2 bales 1 bale 2 bales Box A 3 bales H 1 20m H 1 20m H 1 20m 3 H1 20m independent grabs Bale diameter from 0 90 to 1 80 m 6 4 8 2x4 14 Overall height H 1 070 mm 1 580 mm 1 800 mm 1 800 mm 3 000 mm 750 mm 450 mm 1 450 mm 450 mm 2 550 mm Width L 1 625 mm 1 625 mm 1 625 mm 1 625 mm 1 800 mm In round bale setting 420 mm In rectangular bale setting 1 020 mm Distance between tips In round bale setting 1 510 mm grab opened po In rectangular bale setting 1 570 mm 25 mm Tine working length 340 mm 1 200 kg 230 kg 250 kg 280 kg 740 kg Wrapped bale diameter 1to1 60m 1to1 60m 1to1 60m Up to 800 kg Up to 800 kg Up to 800 kg Number of tines 2 2 SEH 2 3 4 5 950 mm Tine diameter 40 mm from 0 60 to from 0 60 to from 0 60 to from 0 60 to DEER 1 10m 1 10m 1 10m 1 10m d Loader telescopic Loader and TT Loader and Loader and Loader and handler telescopic handler telescopic handler telescopic handler telescopic handler 3 45m 3 85m 3 60 m 3 60m 3 60 m Loader modal as from as from as from as from MX T417 MX T406 MX T408 MX
3. 35690 ACIGN 13 Modification reserved 10 MANUBAL W500 2 bale sensor adjustment The MANUBAL W500 has 2 grabs that operate alternately Picking up 2 bales is achieved without any repeat action 10 1 Operating 10 1 1 Pick up a bale using the lower grab O 10 1 2 Move forward up to the second bale Lower the loader in order for the probe to contact the bale 10 1 3 Without releasing the first bale pick up the second bale by closing the upper grab 10 2 Adjusting the detector The m bale sensor is adjustable for sensitivity Slacken off the 2 screws Adjust the hydraulic block by altering its position Retighten the 2 screws 10 3 Overriding the sensor The 2 grabs can be operated synchronised together To do this the sensor needs to be overridden Operate the probe to its fullest extent Remove the clip and insert it in the upper hole in the drilled screw CAUTION if the MANUBAL bale grab is supplied with independent controls for the 2 grabs there will be no 2 bale sensor MX 7 19 rue de Rennes BP 83221 F 35690 ACIGN 14 Modification reserved 11 MANUBAL V7000 Using the lower tines The MANUBAL V7000 features 3 lower tines particularly suited to handling rectangular bales Its tines may be fixed floating or folding 11 1 Three configurations 11 1 1 Configuration 1 fixed tines Traditional configuration 11 1 2 Configuratio
4. 7 8 Position the first side of the wrapped bale grab kit U section against the grab tine carrier 7 9 Position the other side of the wrapped bale grab kit O section opposite the hole provided for this purpose in the MANUBAL grab 7 10 Insert the pin and the clip supplied in the kit 7 11 Repeat operations 7 8 to 7 10 for the other kit Note the kit is not handed as regards assembly It is identical for the left and right hand sides Option available on MANUBAL V40 V50 W500 MX 7 19 rue de Rennes BP 83221 F 35690 ACIGN 10 Modification reserved 8 LOWERTINE KIT The lower tine kit is recommended for handling rectangular bales It also makes your MANUBAL bale grab even more effective when picking up round or rectangular bales in the field 8 1 Three lower tine kit configurations 8 1 1 Configuration 1 fixed tines Traditional configuration 8 1 2 Configuration 2 floating tines Several benefits It eases withdrawal of the tines when setting a bale down All it needs is to tilt the MANUBAL bale grab forward with the vertical mast and the tines will withdraw It prevents unnecessary pressure from being exerted on the bales when stacking and also the loader from dropping abruptly once the tines are clear Its 2 independently floating tines mean effective stacking even on sloping ground It reduces dragging on the ground thus reducing wear 8 1 3 Configuration 3 fold up tines for ro
5. MANUBAL V40 V50 V500 W500 V7000 User Manual Read carefully before operating the Manubal bale grab UK 364188 AC 0314 Original instructions Dear user We thank you for placing your trust in our product and hope you will find your MX MANUBAL satisfactory in every Way Taking a few minutes to read this manual will enable you to use the capabilities of your MX MANUBAL to the full prolong its service life and ensure safe operation The MANUBAL user manual before you is an important document please retain it in order to be able to refer to it if required Make it available to any other users and hand it over it to any new owner in the event of your MX MANUBAL being sold on The illustrations and technical data shown in this document might not match your MX MANUBAL bale grab exactly operating conditions will nevertheless remain the same D a Rm g I 10 11 12 13 CONTENTS SAFETY RULES SAFETY STICKERS IDENTIFICATION PLATE DESCRIPTION HITCHING UNHITCHING THE MANUBAL BALE GRAB GRAB OPENING CLOSING ADJUSTMENT WRAPPED BALE GRAB KIT LOWER TINE KIT MANUBAL V50 CHANGING GRAB SETTING MANUBAL W500 2 BALE SENSOR ADJUSTMENT MANUBAL V7000 USING THE LOWER TINES MAINTENANCE STORAGE TECHNICAL SPECIFICATIONS A Oo O1 uo 10 13 14 15 16 1 SAFETY RULES The tractor loader or telescopic handler MANUBAL bale grab combination must only be operated by trained and experienced personnel For
6. 35690 ACIGN 7 Modification reserved 6 GRAB OPENING CLOSING ADJUSTMENT The extent of opening and closing of the grab can be adjusted to match the type of bale being handled 6 1 ROUND BALES This setting enables 0 90m to 1 80m diameter bales to be picked up 6 1 1 Position the MANUBAL bale grab upright 6 1 2 Open the grab halfway Lower the MANUBAL bale grab to the ground Stop the engine 364187 10 6 1 3 Remove the clip from the rod end ram pin and remove the pin Note the screw on the pin flat acts to prevent rotation and need not be removed 6 1 4 Position the ram opposite the hole forthe round bale setting See table below 6 1 5 Insertthe pin as well as the synchronising link in the appropriate hole 6 1 6 Refit the clip 6 1 7 Repeat operations 6 1 3 to 6 1 6 for the cylinder end ram pin MANUBAL V40 W500 MANUBAL V50 MANUBAL V500 V7000 MX e 19 rue de Rennes BP 83221 F 35690 ACIGNE 8 Modification reserved 6 2 RECTANGULAR BALE With the grab open the tines do not extend beyond the vertical mast Rectangularbale pick upis more effective 6 2 1 Position the MANUBAL bale grab upright 6 2 2 Open the grab halfway Lower the MANUBAL bale grab to the ground Stop the engine 364187 11 6 2 3 Remove the clip from the rod end ram pin and remove the pin Note the screw on the pin flat acts to prevent rotation and need not be removed 6 2 4 P
7. T410 MX T410 MX T418 Modification reserved EC DECLARATION OF CONFORMITY CE The manufacturer MX 19 Rue de Rennes F 35690 Acign Hereby declares that the following equipment V40 V50 V500 W500 V7000 Manubal Comply with EC directive 2006 42 of the Council of European Parliament and of the council of 17th of May 2009 relating to machines Acign 28th of October 2013 ZZ Loic Mailleux Technical Director MX 19 rue de Rennes BP 83221 F 35690 ACIGNE Tel 33 0 2 99 62 52 60 Faks 33 0 2 99 62 50 22 E mail contact O m x eu
8. 174 Nm Additional lower tine on MANUBAL V500 a 3 tine is available as an option MX 7 19 rue de Rennes BP 83221 F 35690 ACIGN 12 Modification reserved 9 MANUBAL V50 changing grab setting The MANUBAL V50 has 2 vertical grab settings lower setting and raised setting This enables 5 round bales to be stacked using the raised setting A specific feature of the MANUBAL V50 is that the switch from the lower setting to the raised setting and vice versa may be operated without leaving the cab and without an additional hydraulic function on the loader 9 1 Pick up a bale 9 2 Set the MANUBAL V50 horizontal 9 3 Move the tractor forward towards the stack that is being built up in order to operate the pusher this unlocks the grab 9 4 Tiltthe MANUBAL V50 forward in order to cause the grab to slide under the force of gravity this locks the grab in the raised setting 9 5 Crowd the MANUBAL V50 back and set the bale down on top of the stack E To return the grab to the lower setting 9 6 Setthe MANUBAL V50 horizontal 9 7 Operate the pusher against a stacked bale this unlocks the grab 9 8 Crowdthe MANUBAL V50 back in order to cause the grab to slide under the force of gravity this locks the grab in the lower setting CAUTION keep all personnel away from the area in which the loader MANUBAL V50 combination is moving while it is in operation MX 7 19 rue de Rennes BP 83221 F
9. 3221 F 35690 ACIGN 15 Modification reserved CAUTION do not bump into the ends of the grab tines as injury may result For greater safety this operation should be completed with the grab closed Additional tine on MANUBAL V7000 a 4 and 5 tine are available as an option 12 MAINTENANCE STORAGE 12 1 Maintenance Lubricate pivot points regularly See lubrication points below Ensure hydraulic connections are cleaned each time before they are connected See toit that straw or hay residues do not jam up the pivot points Checkthe MANUBAL bale grab to ensure that it is in proper working order throughout and that screws clips and pins are in place before any use Check the condition of the wear bushes and replace them before they are fully worn Lubrication points 12 2 Storage Unhitch the MANUBAL bale grab with the grab opened ram rod retracted Lubricate pivot points Coat the tines with oil MX e 19 rue de Rennes BP 83221 F 35690 ACIGNE 16 Modification reserved 13 TECHNICAL SPECIFICATIONS
10. ad use only on MX loaders This configuration enables the benefits of configuration 2 floating tines to be enjoyed at the same time as being able to fold up the tines when travelling on the road All this requires is to crowd the MANUBAL bale grab back and to raise the loader The tines fold up automatically CAUTION Check that the overall height of the assembly is completely safe for travelling Do not close the grab while the MANUBAL bale grab is tilted Option available on MANUBAL V40 V50 V500 W500 MX 7 19 rue de Rennes BP 83221 F 35690 ACIGN 11 Modification reserved 8 2 Park position When the lower tine kit is not being used the tines can be stowed away in the MANUBAL bale grab without affecting its operation 8 2 1 Place the MANUBAL bale grab on the ground with the grab closed and stop the engine 8 2 2 Remove the clip then the pin from the tine 8 2 3 Remove the tine from its location and slide it into the carrier 8 2 4 Refit the pin and the clip 8 2 5 Repeat the procedure for the 2 tine CAUTION do not bump into the ends of the grab tines as injury may result For greater safety this operation should be completed with the grab closed 8 3 Adjusting tine spacing Spacing between tines may be adjustable according to bale size 8 3 1 Slacken off the nuts on the tine carrier clamp 8 3 2 Slide the carrier along the frame 8 3 3 Retighten the clamp observing the correct tightening torque
11. ase will void MX warranty on the entire supply Any modification to any part of the MX supply rams grab tines crank etc or use of a component installed on the MANUBAL bale grab which has not originated from MX will void MX warranty on the entire MX supply Useonly genuine MX spare parts Do not modify your MANUBAL bale grab yourself or have it modified by anyone else without first requesting written authorisation from MX Failure to comply with these rules may render your MANUBAL bale grab hazardous In the event of damage or injury MX shall not be held responsible in any way Warrantycoverwillceaseimmediatelyintheeventoffailuretoobservethestandardsandinstructionsforuseandmaintenance of the MANUBAL bale grab as stipulated in the user manual THE INSTALLER SHALL BE FULLY LIABLE FOR ANY FITMENT ON A LOADER OTHER THAN MX OR A TELESCOPIC HANDLER WHICH HAS NOT BEEN RECOMMENDED BY MX MX ZB 19 rue de Rennes BP 83221 F 35690 ACIGN 4 Modification reserved 2 SAFETY STICKERS Ensure the labels are clean and legible replace them if damaged 1 Location MANUBAL frame carrier Familiarise yourself with the safety rules in the user manual before using or working on the unit 2 Location Lower tine kit carrier optional or on V7000 frame Familiarise yourself with the safety rules in the user manual before using or working on the unit MX implements are designed to offer the operator of
12. n 2 floating tines Several benefits It eases withdrawal of the tines when setting a bale down All it needs is to tilt the MANUBAL bale grab forward with the vertical mast and the tines will withdraw Itprevents unnecessary pressure from being exerted on the bales when stacking and above all the telescopic handler boom dropping abruptly once the tines are clear ltreduces dragging on the ground and thus reducing wear CAUTION do not close the grab while the MANUBAL bale grab is tilted 11 1 3 Configuration 3 fold up tines for road use 1 Open the grab to its fullest extent ram in rectangular bale setting see chapter 6 2 Stop the engine 2 Remove clips and pins 3 Fold up the tines and carrier assembly 4 While holding this position refit the pins and clips in the holes provided for this purpose CAUTION do not close the grab with the tines folded up 11 2 Park position When the lower tines are not being used they can be stowed away in the MANUBAL bale grab without affecting its operation 11 2 1 Place the MANUBAL bale grab on the ground with the grab closed and stop the engine 11 2 2 Remove the clip then the pin from the tine 11 2 4 Refit the pin and the clip 11 2 5 Repeat the procedure for the 2 and 3 tine MX 7 19 rue de Rennes BP 8
13. osition the ram opposite the hole for the rectangular bale setting See table below 6 2 5 Insertthe pin as well as the synchronising link in the appropriate hole 6 2 6 Refit the clip 6 2 7 Repeat operations 6 2 3 to 6 2 6 for the cylinder end ram pin MANUBAL V40 W500 MANUBAL V50 MANUBAL V500 V7000 MX e 19 rue de Rennes BP 83221 F 35690 ACIGN 9 Modification reserved 7 WRAPPED BALE GRAB KIT This kit converts your MANUBAL unit into a round wrapped bale grab The conversion is very simple and is accomplished in just a few seconds Wrapped bale grab opening closing adjustment The adjustment is carried out using the holes provided for round wrapped bales 7 1 Position the MANUBAL bale grab upright 7 2 Openthe grab halfway Lower the MANUBAL bale grab to the ground Stop the engine 7 3 Remove the clip from the rod end ram pin and remove the pin Note the screw on the pin flat acts to prevent rotation and need not be removed 7 4 Position the ram opposite the hole for the wrapped bale setting See drawing CAUTION the synchronising links should be removed 5 from the MANUBAL bale grab when it is used for wrapped bales which allows the 2 grab arms to float This enhances effectiveness andsafety whenstackingbalescontiguously 7 5 Insert the pin in the appropriate hole 7 6 Refit the clip 7 7 Repeat operations 7 3 to 7 6 for the cylinder end ram pin
14. ric power ortelephone lines guttering roof trusses etc Whenever the tractor or telescopic handler is stopped momentarily or for an extended period the engine must be shut down and the MANUBAL bale grab lowered When notin use protruding items such as tine ends must be protected or stowed grab closed lower tine kit retracted Check periodically to ensure that safety pins and bolts are in place Do not replace them with any other items such as nails wire etc Any adjustment on the MANUBAL bale grab ram position tines in fixed or floating position etc must be carried out after the MANUBAL bale grab has been lowered to the ground and the tractor or telescopic handler engine shut down grab in lower setting for the MANUBAL V50 unit Anyworkinvolving fault tracing diagnostics and or disassembly of parts may only be undertaken by a skilled technician who will start with an assurance that the work will be carried out in complete safety for himself and his surroundings A Caution Check hoses for length and routing in all configurations fully crowded fully dumped etc before first use The MANUBAL bale grab is designed to withstand a maximum operating pressure of 210 bar Above this pressure the MANUBAL bale grab will require to be fitted with a pressure limiter Anyinstance ofa MANUBAL bale grab being fitted which ignores the recommendations in the MX price listin force on the date of purch
15. the prime mover to which they are fitted optimum angles for crowding and dumping at ground level Before handing over to the operator the installer must check that there is no possibility of interference occurring between the implement which has been fitted and other components of the machine tyres mudguards etc as a result of the maximum travel of the implement installed when the telescopic handler boom positions the implement closest in to the machine In the event of the aggregation of positional conditions of the implement and the boom leading to interference the installer is to notify the operator and provide him with instructions on how to prevent such interference In general it is sufficient to operate with the boom extended by at least 0 5 m MX cannot be held liable for any damage or accidents which might result from impacts caused by this 3 IDENTIFICATION PLATE Identification details are to be passed on to your dealer with any request for spare parts or service work Its location is shown below 3 Location MANUBAL frame carrier MANUBAL identification data plate 19 rue de Rennes F 35690 ACIGN X D signation Designation Type Model Typ N de s rie Serial number Seriennummer Arm e Y sr Poids vide K 2 Unloaded weight Leergewicht g S MX es 19 rue de Rennes BP 83221 F 35690 ACIGN 5 Modification reserved
16. your complete safety and that of others strict compliance with the hitching and unhitching procedure for the MANUBAL bale grab is required chapter 5 of this manual Only control the MANUBAL bale grab from the driver s seat Keep operating the controls until movements stop Do not leave the driver s seat without stopping all control movements All personnel must be kept away from the area in which the loader or telescopic handler MANUBAL bale grab combination is moving while it is in operation Never pass under a raised bale Never use the MANUBAL bale grab to push a bale Carrying or lifting personnel using the MANUBAL bale grab is forbidden Never stand or pass under the load Before any operation the user must ensure that the MANUBAL bale grab is in proper working order and can be used in complete safety He must also check and ensure that the tractor loader MANUBAL bale grab combination is stable by fitting acounterweight to the back of the tractor This should ensure that 20 of gross weight remains on the rear axle of the tractor for optimum safety while travelling and working When travelling on the road it is imperative that the regulations governing use on the public highway be observed size implement markings etc Protruding items such as tine ends must be protected or stowed grab closed lower tine kit retracted Take great care when operating at heightin orderto avoid catching any items elect
Download Pdf Manuals
Related Search