Home

Slimline 229 - MCM Electronics

1. www prolight co uk Slimline 229 Order code LEDJ51 USER MANUAL LEDJ Slimline 229 WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP CAUTION Keep this equipment away from rain moisture and liquids SAFETY INSTRUCTIONS Every person involved with the installation operation amp maintenance of this equipment should Be competent Follow the instructions of this manual CAUTION TAKE CARE USING THIS EQUIPMENT HIGH VOLTAGE RISK OF ELECTRIC SHOCK Before your initial start up please make sure that there is no damage caused during transportation Should there be any consult your dealer and do not use the equipment To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual Please note that damages caused by user modifications to this equipment are not subject to warranty LEDJ Slimline 229 Safety IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment e Never let the power cable come into contact with other cables Handle the power cable and all mains voltage connections with particular caution e Never remove warning or informative labels from the equipment Do not open the equipment
2. Link the units together using a 3 pin DMX cable then press the MODE button to select one of the above modes On the Slave units press the mode button until the LED display shows SLAV The slave units will then follow in sequence with the Master unit 6 LED mode Use this mode to switch the LED display On and Off 7 Sound active mode Mode button Press the MODE button until the LED display shows SU00 then press the ENTER button to set the desired sensitivity level using the UP and DOWN buttons The sound sensitivity levels are from 00 99 00 low 99 high 8 DMX Addressing mode To access the DMX address mode press the MODE button until the LED display shows A001 then press the ENTER button and set the first digit in the DMX address using the UP and DOWN buttons Now repeat this step to set the second and third digits for the desired DMX address setting Follow the DMX channel assignment and function table overleaf Note The speed settings for operation modes 2 and 3 are from 00 99 00 slow 99 fast The strobe speed settings for operation modes 1 2 and 3 are from 00 99 00 slow 99 fast LEDJ Slimline 229 Operation 7 Channel DMX chart Channel Value Function Hs ter t00 151 255 Colour fade LEDJ Slimline 229 DMX Setup DMX 512 DMX Digital Multiplex is a universal protocol used as a form of communication between intellige
3. and do not modify the equipment e Do not connect this equipment to a dimmer pack e Do not switch the equipment on and off in short intervals as this will reduce the system s life e Only use the equipment indoors Do not expose to flammable sources liquids or gases e Always disconnect the power from the mains when equipment is not in use or before cleaning Only handle the power cable by the plug Never pull out the plug by pulling the power cable Make sure that the available voltage is between 220v 240v e Make sure that the power cable is never crimped or damaged Check the equipment and the power cable periodically If the equipment is dropped or damaged disconnect the mains power supply immediately Have a qualified engineer inspect the equipment before operating again If the equipment has been exposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature If your product fails to function correctly discontinue use immediately Pack the unit securely preferably in the original packing material and return it to your Prolight dealer for service Only use fuses of same type and rating Repairs servicing and power connection must only be carried out by a qualified technician THIS UNIT CONTAINS NO USER SERVICEABLE PARTS WARRANTY One year from da
4. colour and any brightness Press the MODE button to show C1 with two digits after it The C1 represents Red C2 Green C3 Blue C4 Amber and CF strobe The two digits after it are the brightness 00 to 99 or in CF they are the strobe speed Examples If you set C1 C2 C3 and C4 all to zero your 229 will have no LEDs showing blackout If you set C1 to 99 and C2 C3 and C4 to zero your 229 wil be 100 Red 2 Colour change mode Mode button Press the MODE button until the LED display shows JU00 then press the ENTER button to choose one of the colour changing modes using the UP and DOWN buttons 1 JU00 RGBA 15 colours 2 JF00 Strobe Now press the ENTER button again and you can then select the colour change speed using the UP and DOWN buttons 3 Colour fade mode Mode button Press the MODE button until the LED display shows F000 then press the ENTER button to choose one of the colour fading modes using the UP and DOWN buttons 1 FA00 RGBA 15 colours 2 FF00 Strobe Now press the ENTER button again and you can then select the colour fade speed using the UP and DOWN buttons 4 Auto Run mode Mode button Press the MODE button until the LED display shows AUTO the unit will now run through it s built in programmes 5 Slave mode
5. D va eal Pin 2 Signal Pin 3 Signal 5 Pin XLR socket 3 Pin XLR socket f Pin 1 GND screen Pin 1 GND ir n Pin 2 Signal Pin 2 Signal Pin 3 Signal Pin 3 Signal A z ni Ne in 5
6. M CABL11 5M CABL 12 10M Also remember that DMX cable must be daisy chained and cannot be split LEDJ Slimline 229 DMX Setup Notice Be sure to follow figures 2 4 3 when making your own cables Do not connect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing Grounding the shield could cause a short circuit and erratic behaviour common DMX 512 out DMX 512 in 3 pin XLR 3 pin XLR RE oa XLR MALE SOCKET XLR FEMALE SOCKET XLR Pin Configuration 2 cold 1 ground 1 ground Pin 1 Ground 2 cold Pin 2 Negative FIGURE 3 FIGURE 2 Special Note Line termination e When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behaviour Termination reduces signal transmission problems O and interferance it is always advisable to connect a o DMX terminal resistance 120 Ohm 1 4 W between pin 2 DMX and pin 3 DMX of the last fixture Using a cable terminator part number CABL90 will decrease the possibilities of erratic behaviour 5 Pin XLR DMX Connectors Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 Pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used The Chart below details the correct cable conversion 3 Pin XLR socket Pin 1 GN
7. nt fixtures and controllers ADMX controller sends DMX data instructions form the controller to the fixture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a data out terminal DMX Linking e DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain DATA Cable DMX cable requirements for DMX operation e The Slimline 229 can be controlled via DMX 512 protocol The DMX address is set on the back of the unit Your unit and your DMX controller require a standard 3 pin XLR connector for data input output figure 1 Figure 1 Further DMX cables can be purchased from all good sound and lighting suppliers or Prolight dealers Please quote CABL10 2
8. te of purchase OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty becomes void Incorrect operation may lead to danger e g short circuit burns electric shocks lamp failure etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and property LEDJ Slimline 229 Technical specifications You should find inside the LEDJ carton the following items 1 Slimline 229 Unit 2 Instruction manual Technical Specifications DMX channels 7 400Hz flicker free RGBA LEDs Power supply AC 240 50Hz 229 Ultra Bright 10mm LEDs R 36 G 63 B 61 A 69 Power Consumption 20W Beam angle 25 degrees Dimensions 79 x 268 x 320mm Weight 2 5Kgs Operating modes 1 Static Colour mode 2 Colour change mode 3 Colour Fade mode 4 Auto Run mode 5 Slave mode 6 LED mode 7 Sound active mode 8 DMX mode O Overview SLIMLINE 229 DMX OUT G www prolight co uk e Power in E y gt CE 60Hz Power out de Enter Up Do 1 DMX input 2 DMX output 3 LED display 4 Power input 5 Power output 6 Mode selection button 7 Set up button 8 Function up button 9 Function down button 10 On Off switch DO LEDJ Slimline 229 Operation 1 RGBA colour mix mode In this mode you can set the Slimline 229 to any

Slimline 229 - MCM Electronics

Contents

Download Pdf Manuals

Related Search

Related Contents