Home

TRENDnet User`s Guide Cover Page

1. Ul le Saturation Sense Up s in EE i Sharpness D WDR Off X AGC Q Le Video Orientation BH Flip Mirror Mf Rotate 90 Shutter Time g a g ba in Sense Up D WDR Off Video Orientation E Flip MM Mirror W Rotate 90 Day amp Night Light Sensor Mode z Night to Day Lux about Day to Night Lux EIS Current Lux about White Balance Red gain Blue gain amp Denoise 3D 5 Asi Copyright 2014 TRENDnet All Rights Reserved 25 TRENDnet User s Guide TV IP342Pl Privacy Mask For the security and privacy purpose there are three areas can be setup for privacy mask Click Area button first and drag an area on the above image and remember to save your setting The masked area will not show on both the live view and recording Brightness Contrast Hue Saturation Sharpness can be adjusted here AGC Automatic gain control The sensitivity of camera can be adjusted with the environmental light Enable this function and the brighter image can be got under dim light but the level of noise may also increase Shutter Time Choose as the location of your camera or fixed shutter time The shorter the shutter time is the less light the camera receives and the image becomes darker Sense Up This function increases the sensitivity of camera to get brighter image at night The smaller the value you select the slower the shutter speed becomes so tha
2. e Sensitivity Select motion detection sensitivity from 1 to 10 e Trigger Action Area 1 Area 2 Area 3 When motion is detected the camera can send video or snapshot to Email FTP Output device and Samba Note Due to network Internet bandwidth constraint the IP camera may not transfer video to selected destinations simultaneously Keep the number of destinations as few as possible to avoid possible data loss e Subject This subject will appear as the subject when sending the motion detected video or snapshot to email Copyright 2014 TRENDnet All Rights Reserved e Interval Each motion triggered in defined interval time If you select 10 sec here once the motion is detected and action is triggered the next motion will be trigger after 10 seconds e Based on the schedule The motion detection will be triggered based on the schedule you define Event Configuration gt gt Motion Detection gt gt Tampering Detection Tampering Detection Tampering Enabled Disabled BeE mal FIP 8 Outi MB SavetoSDcard MW Samba o0sec e Tampering Enable Disable Tampering When enabled and tampering is detected the camera will send video or snapshot to Email FTP Output device or Samba Event Configuration gt gt Motion Detection gt gt Record File Record File File Format AVI File with Record Time Setting When an event occurs the IP camera can record a video clip or take snapshot and then
3. TRENDnet warrants its products against defects in material and workmanship under normal use and service for the following lengths of time from the date of purchase TV IP342PI 3 Years Limited Warranty AC DC Power Adapter Cooling Fan and Power Supply carry 1 year warranty If a product does not operate as warranted during the applicable warranty period TRENDnet shall reserve the right at its expense to repair or replace the defective product or part and deliver an equivalent product or part to the customer The repair replacement unit s warranty continues from the original date of purchase All products that are replaced become the property of TRENDnet Replacement products may be new or reconditioned TRENDnet does not issue refunds or credit Please contact the point of purchase for their return policies TRENDnet shall not be responsible for any software firmware information or memory data of customer contained in stored on or integrated with any products returned to TRENDnet pursuant to any warranty There are no user serviceable parts inside the product Do not remove or attempt to service the product by any unauthorized service center This warranty is voided if i the product has been modified or repaired by any unauthorized service center ii the product was subject to accident abuse or improper use iii the product was subject to conditions more severe than those specified in the manual Warranty service may be
4. and then press the ENTER key on your keyboard b Open Internet Explorer and enter http 192 168 10 30 into the address bar Windows Vista If the installation menu does not appear automatically click Start click the Start Search box and type D autorun exe where D in D autorun exe is the 4 The image is blurry How can I adjust the focus on the IP camera letter assigned to your CD ROM Drive and then press the ENTER key on your keyboard The camera equipped with external vari focus lens control Adjust the focus zoom by parallel turn the switch Zoom Windows XP If the window does not appear automatically click Start click Run and type D autorun exe where D in D autorun exe is the letter assigned to your CD ROM Drive and then press the ENTER key on your keyboard Focus Copyright 2014 TRENDnet All Rights Reserved 38 TRENDnet User s Guide TV IP342PIl 5 When I click on Live View the image does not load what should I do a Ifyou are using Internet Explorer make sure that you install the ActiveX control WEBWATCH cab b If you are using non lE browser Firefox Chrome Safari make sure that you install the plug in WebPlugin exe 6 How do l uninstall the browser s Active X or Plug in from my computer Click Computer Icon type in np_hoem_x dll on the top right corner of the search bar then click Search la I Organize v System properties Uninstall or cha
5. that the bandwidth is divided For example if you set 5 10 and 20 for these three items then the bandwidth of these items is 5 10 20 The item getting more bandwidth has lower probability to be delayed There is no difference between setting 0 0 O or 63 63 63 because under these two setting the three items will get equal bandwidth 1 3 The three stream control the protocols respectively e Live Stream Video and audio RTP RTSP e Event Alarm FTP SMTP SAMBA SIP e Management HTTPS HTTP SNMP Note The Management stream handles both the live view and the setting area of the web page on which the data is transferred via http https protocol If you prefer to distribute more bandwidth when using the web browser to watch the live video please adjust the Management Stream instead of Live Stream 20 TRENDnet User s Guide TV IP342PI Network gt gt Advanced gt gt IEEE 802 1x Network gt gt PPPoE amp DDNS IEEE 802 1x Setting PPPoE amp DDNS Enable IEEE 802 1x EAPOL version 0v1i1 v2 PPPoE Setting Username y Private key password Password l Send il after PPPOE jailed e E CA certificate E Opoa cmb DDNS Setting Enable Enabled 9 Disabled Provider Client certificate Hostname J Username ae Password as Schedule Update 4400s Client private key Upload State IEEE 802 1x is an IEEE standard for port based Network Access Control It provides an Note authentication mechanism t
6. Certificate Country State or province Locality Organization Organizational Unit Common Name Validity After finishing installation you can click Content to call out and check the certificate content Installed Certificate Subject C TW ST L O OU CN Date Apr 26 02 45 20 2014 GMT Content Remove Copyright 2014 TRENDnet All Rights Reserved 5 To use Https to access camera open your browser and key in https IP address in the address bar Now your data will be transmitted via encrypted communications and the browser will check your certificate status If it shows you a warning message The warning message meant that the certificate is self signed or signed by distrusted institution Click Continue to this website to view the view the camera x There is a problem with this website s security certificate The security certificate presented by this website was not issued by a trusted certificate authority The security certificate presented by this website has expired or is not yet valid The security certificate presented by this website was issued for a different website s address Security certificate problems may indicate an attempt to fool you or intercept any data you send to the server We recommend that you close this webpage and do not continue to this website Click here to close this webpage Continue to this website not recommended More information
7. Subject C TW ST L O OU CN Date Mar 14 08 45 42 2038 GMT Connection Types HTTP Vv Created Request Fill in the following form and click apply Create Request Country State or province Locality Organization Organizational Unit Common Name 17 TRENDnet User s Guide TV IP342Pl 3 After you generate a certificate request if you choose to turn it to the trusted third party to verify please click Content and copy all the request content Certificate Request Data Created Request Version 0 0x0 Subject C TW Subject C TW ST L O Subject Public Key Info Public Key Algorithm rsaEncryption Public Key 1024 bit Modulus Content Remove 00 d6 65 25 d9 30 02 65 76 72 07 b3 51 43 1d a5 c3 6 87 d0d1 19 3c 8b 52 40 3e 4a 2 9b 7Te daf a5 25 8 95 ed 2d ca 96 50 96 d3 ee 12 ed e 3 96 c6 20 9d b6 0e 58 99 94 dc 47 08 ec 56 44 6 95 1b 93 e9 2d eb 1e 02 0 2 c 85 1b 28 Date 2014 Mari26 18 35 17 4 According to the certificate source there are two ways to install the certificate lf you had sent the certificate request to do sign and received a signed certificate please click browse and find the certificate file in your computer Click Apply to install it Ifyou choose to generate a self signed certificate fill in the following forms and set validity day click Apply to finish installed it Create Self Signed
8. TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER S OR ANY THIRD PERSON S MISUSE NEGLECT IMPROPER INSTALLATION OR TESTING UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE OR BY ACCIDENT FIRE LIGHTNING OR OTHER HAZARD LIMITATION OF LIABILITY TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY WHETHER BASED IN CONTRACT OR TORT INCLUDING NEGLIGENCE FOR INCIDENTAL CONSEQUENTIAL INDIRECT SPECIAL OR PUNITIVE DAMAGES OF ANY KIND OR FOR LOSS OF REVENUE OR PROFITS LOSS OF BUSINESS LOSS OF INFORMATION OR DATE OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE USE PERFORMANCE FAILURE OR INTERRUPTION OF THE POSSIBILITY OF SUCH DAMAGES AND LIMITS ITS LIABILITY TO REPAIR REPLACEMENT OR REFUND OF THE PURCHASE PRICE PAID AT TRENDNET S OPTION THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE Governing Law This Limited Warranty shall be governed by the laws of the state of California Some TRENDnet products include software code written by third party developers These codes are subject to the GNU General Public License GPL or GNU Lesser General Public License LGPL Go to http www trendnet com gpl or http www trendnet com Download section
9. You can choose 32kbps 1Mbps The higher the value is the higher the image quality is Video Frame Rate The video refreshing rate per second The max value is affected by the input resolution you choose 28 TRENDnet User s Guide TV IP342PI Video Format H 264 or MPEG4 EVENT CONFIGURATION RTSP Path 3GPP output connecting route If the IP address of your camera is 192 168 1 160 and you type in 3g in the column the 3GPP path will be rtsp 192 168 1 160 3 gt aad Motion Detection Motion Detection NETWORK Audio Video Setting gt gt Audio Setting AUDIO VIDEO SETTING IP Camera supports 2 way audio Audio can be received by the microphone connected lt EVENT CONFIGURATION with IP camera and transmitted to remote PC User can also send audio from remote Motion Detection computer s microphone to IP Camera s external speaker Sound Detection e Two Way Audio Schedule GPIO Setting Select Enable then you can see Mic and Speaker options on the live page The Logs Area Setting Sensitivity E Area 1 E E maili FTP W outi MBSavetoSDcard W Samba Audio compression format can be chosen from 3 options You can also adjust the volume of 2 way audio Two Way Audio E Area 2 B E maili FreP Mouti W Saveto SDcard W Samba e ae Enable Enabled Disabled Area 3 BeE mal FrP W Outi W Save to SDcard W Samba p Subject larning Audio Type J IP Camera Warning Interval
10. and look for the desired TRENDnet product to access to the GPL Code or LGPL Code These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers TRENDnet does not provide technical support for these codes Please go to http www gnu org licenses gpl txt or http www gnu org licenses Igpl txt for specific terms of each license 40 TRENDnet Product Warranty Registration Please take a moment to register your product online Go to TRENDnet s website at http www trendnet com register TRENDnet 20675 Manhattan Place Torrance CA 90501 USA Copyright 2014 All Rights Reserved TRENDnet
11. click the mouse for the additional menu options e Frame Buffer mSec This function is to build a temporary buffer to accumulate several video frames This function can make video smooth going when the Network speed is slow and lag If you select 100 then it plays video after 100 mSec when starting receiving images from camera The slower of the Network is the bigger value should be selected The default value is null Snapshot y Record Start 2014 MAY 09 11 09 50 Size 1920x1080 FPS 30 i Mute Full Screen Zoom FrameBuffmSec b e Snapshot Save a JPEG picture e Record Start Record the video in the local PC It will ask you where to save the video To stop recording right click the mouse again Select Record Stop The video format is AVI Use Microsoft Media Player to play the recorded file e Mute Turn off the audio Click again to turn on it The mute button does not affect the playback recording video As long as the 2 Way Audio option in the audio setting is enabled all the audio will be recorded into the playback video even you click mute in the live page e Full Screen Full screen mode e Zoom Enable zoom in and zoom out functions Select Enable digital zoom option first within the pop up dialogue box and then drag and drop the bar to adjust the zoom factors Copyright 2014 TRENDnet All Rights Reserved 10 TRENDnet User s Guide TV IP342PI Configuring t
12. if you have only one camera installed If you have more than one camera in the same Network you will need to identify the camera by the MAC ID Click Next Select your camera The following cameras were detected on your network Check the MAC address of the IP Camera you are going to setup and select it from the list Model Mac Address TV P343PI FF FF FF FFFF FF If you don t see your camera s MAC address confirm that the camera is powered up confirm your computer is connected to your network and then click the Retry button Copyright 2014 TRENDnet All Rights Reserved 8 Select DHCP option to assign an IP by DHCP server or Select Fixed IP to set IP address manually Click Next Select a Connection Option Please select a connection option based on your network environment If you do not know which connection option to choose select DHCP Select this option if your camera is connected to a router and DHCP is enabled Fixed IP Select this option if you want to configure the camera with a static IP address 9 If you select Fixed IP fill out the IP address subnet mask default gateway DNS server Please ensure that the IP address of the camera and the computer must within the same network Click Next Fixed IP Address Setup Please input the correct network address information IP Address 192 168 10 50 Subnet Mask 255 255 255 0 Default Gateway 192 168 10 1 Primary DNS 192 168 10 1 TRENDn
13. obtained by contacting TRENDnet within the applicable warranty period and providing a copy of the dated proof of the purchase Upon proper submission of required documentation a Return Material Authorization RMA number will be issued An RMA number is required in order to initiate warranty service support for all TRENDnet products Products that are sent to TRENDnet for RMA service must have the RMA number marked on the outside of return packages and sent to TRENDnet prepaid insured and packaged appropriately for safe shipment Customers shipping from outside of the USA and Canada are responsible for return shipping fees Customers shipping from outside of the USA are responsible for custom charges including but not limited to duty tax and other fees WARRANTIES EXCLUSIVE IF THE TRENDNET PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE THE CUSTOMER S SOLE REMEDY SHALL BE AT TRENDNET S OPTION REPAIR OR REPLACE THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED EITHER IN FACT OR BY OPERATION OF LAW STATUTORY OR OTHERWISE INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE OR USE OF TRENDNET S PRODUCTS Copyright 2014 TRENDnet All Rights Reserved TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS
14. send the file to mail FTP Samba Select what format you want to save e AVI File with Record Time Setting Save AVI video file The video length is according to the value you set in Record Time Setting e JPEG File Single File with Interval Setting Save single JPEG picture file when event occurs e JPEG Files with Record Time Setting Only when you select JPEG in streaming 1 video format of Video Setting this option can be enabled Select this option to save several JPEG picture files and the successive picture files cover a period of time according to the value you set in Record Time Setting 30 TRENDnet User s Guide TV IP342PIl Event Configuration gt gt Motion Detection gt gt Record Time Setting Record Time Setting Pre Alarm Kse w Post Alarm When an event occurs the IP camera can record a video clip or take snapshot and then send to mail FTP Samba Select the video recording length before and after event occurs Event Configuration gt gt Motion Detection gt gt Network Disconnected Network Disconnected Disconnected E Save to SD card When enabled the live view will be stored into the SD card if the IP Camera detects no Internet Connection the SD card must be pre installed Event Configuration gt gt Motion Detection gt gt Network IP Check Network IP Check IP Check Enabled Disabled IP Address Interval E Connection failed four times Reboot IP Camer
15. 322 org no ip com and IPTECNO DDNS Enable DDNS and select a DDNS provider Some providers will ask you to register and get an account before you use their service Fill in the user name hostname and password if need If setting up IP schedule update too frequently the IP may be blocked In general we suggest set schedule update to once a day 1440 minutes After click Apply the setting Copyright 2014 TRENDnet All Rights Reserved DDNS Status Updating Information update Idle Stop service DDNS registration successful can now log by http lt username gt noip com Register successfully Update Failed the name is already registered The user name has already been used Please change it Update Failed please check your internet connection Network connection failed Update Failed please check the account information you provided The server user name and password may be wrong 22 TRENDnet User s Guide TV IP342PI Network gt gt Event Server The settings of Email FTP and SAMBA are used when the event occurs schedule Event Server snapshot executes or the alarm input is triggered Select the item to display the detailed configuration options You can configure either one or all of them Mail Setting e Mail Setting Login Method Mail Setting Login Method Mail Server Username Mail Server Username Password a Password Sender s Mail Sender s Mail Receiwer s Mail R
16. Interval The interval between two snapshots When Record is enabled e File Name Give the snapshot file name The saved file will be named as file name saving date saving time e Enabled Disabled e Destination Select between sending the record to Samba or saving it into the SD Event Configuration gt gt GPIO Setting card Input Setting e Record Time Select the video length seconds Input 1 Sensor N O W E E mail E FIF E Outi Input 1 Acton E Save to SD card E Samba Subject GPIO In Detected Interval E Based on schedule Output Setting Mode Setting O On Off Switch Time Switch Interval Copyright 2014 TRENDnet All Rights Reserved 32 TRENDnet User s Guide TV IP342PIl 1 I O Connection Please connect the GND amp DO pin to the external relay buzzer device When no event occurs DO output is 5V DO and GND are disconnected When the camera detects event happening and triggers external alarm DO output is OV DO and GND are connected 5V OFF Not Pulse 5V ON Pulse OV Please connect the GND amp DI pin to the external trigger device If you select N O in Input sensor setting when external devise or circuit makes DI and GND pin connected the camera input alarm is triggered and then camera will execute the action user has set for example send snapshot to E mail address If you select N C in Input sensor setting when external devise or circuit
17. Network gt gt Advanced gt gt SNMP SNMP Simple Network Management Protocol provides a simple framework for administering networked hardware To manage the IP camera you have to prepare a MIB browser or similar tools first SNMPv1 SNMPv2c and SNMPv3 can be enabled simultaneously The following examples are based on MG SOFT MIB Browser Depending on your MIS Browser you may see different interface and options Please refer to the user manual of your MIB Browser e SNMPvi and SNMPv2 BSNMPv1 E SNMPv2c Write Community Read Community ES The term Community name in SNMPv1 and SNMPv2c can be roughly regarded as key The person who has the community name has the authority to read or edit the information of IP camera via SNMP 18 TRENDnet User s Guide TV IP342Pl Click the box to enable SNMPv1 or SNMPv2c protocol and specify the community name for write read and write and read read only The user who use read community name to access the IP camera cannot modify any data of the camera The community name can be any English characters and numbers and must be shorter than 31 bits SNMPv3 E SNMPv3 Write Security Name fine Authentication Type OmMDS SHA Authentication Password Encryption Type Encryption Password Read Security Name Authentication Type Authentication Password Encryption Type Encryption Password For data security reason the authentication and encryption as
18. User s Guide TRENDnet Outdoor 2MP Full HD PoE Day Night Dome Network Camera TV IPS42PI TRENDnet User s Guide LEL Ka LE Contents Product OVervie W ssn seucsiccn sn enanesiuescoes e E a 2 Package OS eisirereriripipaini nanen a EENAA R aana 2 PoU ar i E A E E pean acuanaienneains 2 Product Hardware Features sstsicnnccaencsscsnadenceaetdaadnnelonssesnuducddnesdaasuanmteatonabenssaaeadedacneudaenedis 3 EION een E E E 4 Hardware Installation cccccccccccccssssssssssesseeeeeececcceeeeeeaaaeeeessseeeeeeeeeeeeeeeeeeaaaaeaasseeseeeeeeess 4 Camera Installation ccsctsta Aaectmen aoa sap actanaep ctndesntep coemeatsnsteseauapetacannpcnte asa aime sstncumtsantcignnvopcaasae 6 ON CU AION saecciccncsccseccociece EA E 9 Viewing Camera Basic FUNCTION ccsscccssccsecessccssccesscesseceecceusesseesesecessetaeeseuseesectsesees 9 Configuring the Camera Setting ucnssdccsccdeocestecetsasccdetesatenedensxccaucanteuebncsesiniacsaeval caeeusiacateds 11 YG COI PEE E E A E cma de ie becuse A EE E AE E E T 11 ITN OBR oe a E E denned amanasetdeamaestaoadatnddoaay 14 AUDIO VIDEO SETTING cccssscccccessssssseeeececesssssseeeecesseeesaeeeeeeesseensaeeeeeesssesnsaaeeseesessgs 25 EVENT CO NIG RTO Ne cp cctem crt criemeesem neteecatencuce cap stase aaitnamamcuap neleecuep case adap aenaatnanambaapnclenanepanars 29 How to Switch the Cable Access Port csscssccssccssccscccsccesccecccscceseeees 35 How to Access the IP camera via IP Install
19. a Check failed E Save to SD card Enter the target IP address and interval The camera will base on the interval time to check the target IP address If PIN failed 4 times the camera itself will reboot Copyright 2014 TRENDnet All Rights Reserved Event Configuration gt gt Sound Detection gt gt Sound Detection Sound Detection Sound Detection Enabled Disabled BeE mal OO FIP 8 Outil OE SavetoSDcard 8 Samba Detection Level e When enabled and the camera detects sound the IP camera can record a video clip or take snapshot and then send the file to mail FTP Samba Select what format you want to save e Detection Level Selects the decibels value for the camera to trigger sound detection 31 TRENDnet User s Guide TV IP342PI Event Configuration gt gt Schedule When Snapshot is enabled With schedule setup With schedule setup h rd Snapshot amp Reco Record O Snapshot Close Snapshot amp Record Snapshot Record Snapshot Close Enabled Disabled Record Snapshot E E mail W FIP W SavetoSDcard W Samba Enabled Disabled Interval w SUT ES Beare eel Destination Samba Save to SD card File Name Record Time Click on the week calendar to draw color The actions will be performed during the e When enabling the snapshot function the IP camera will take snapshot according to colored time schedule Select the snapshot saving way E mail FTP or Samba e
20. a period of time between every two motions detected Adjust Volume Based on schedule Mic In Line Out e Receive sound from IP Camera or speak to IP Camera Click Mic check box to receive sound from IP Camera and click Speaker to talk to IP camera side Please ensure both IP camera and the computer sides have the microphone and speaker installed to have this function work properly Streaming 1 Y Speaker W Mic W Online Visitor 1 Relay Out On O OFF Copyright 2014 TRENDnet All Rights Reserved Copyright 2014 TRENDnet All Rights Reserved 29 TRENDnet User s Guide TV IP342Pl Event Configuration gt gt Motion Detection _ Motion Detection Motion Detection NETWORK AUDIO VIDEO SETTING EVENT CONFIGURATION Motion Detection Sound Detection Schedule GPIO Setting ec Logs SD Card ae en Area 1 Be mail FrP W Outi W Save to SDcard W Samba iReicieltny E Area 2 e mal Fre W oOuti MSavetoSDcard W Samba E Area 3 eE mail FTP W Outi W Saveto SDcard W Samba Subject IP Camera Warning Interval a period of time between every two motions detected E Based on schedule e Area Setting Click Area 1 Area 2 Area 3 icon then draw the motion detection area on the live screen If there is any motion detected in these areas the Motion wording will show on the live screen To clean the motion detection area click Area 1 Area 2 Area 3 icon again
21. access from your computer aa _ P To access the camera now click here lf DHCP Mode selected In this mode the camera s IP Address may change To find the camera s current IP address for future access click the above link Copyright 2014 TRENDnet All Rights Reserved TRENDnet User s Guide TV IP342PIl Viewing Camera Basic Function Open the Web browser on your computer example showed in this User s Guide is based on the Internet Explorer In the Address bar type the IP address you got from Camera Installation chapter or found by IP Installer and then press Enter New Tab Windows Internet Explorer gia A http 192 168 10 30 File Edit View Favorites Tools Help When the login window appears enter the User name admin and Password and press OK to access to the main screen of the camera s Web Configuration Login to the TV IP342PI Language English User Name Password Note if you are initially access to the camera you will be prompted to install a new plug in for the camera Permission request depends on the Internet security settings of your computer Click Allow and Install to process This webpage wants to run the following add on WebWatch2 ActiveX Control Module from TRENDnet Inc Copyright 2014 TRENDnet All Rights Reserved After you login into the live screen of the camera the main page will appear as below TRENNNET Outdoor FMP Full HD PoE Day Night D
22. ber in Sense up Indoor NTSC 1 125 Selected number in Sense up PAL 1 100 Selected number in Sense up 1 30 1 10000 1 30 1 50 1 10000 1 50 1 60 1 10000 1 60 Sense up options 1 30 1 15 1 10 1 5 26 TRENDnet User s Guide TV IP342PI Audio Video Setting gt gt Video Setting e Video Settings Video Video Settings Video System Video Settings TV Output Auto Based on the Video System r s TV Output Focus Bar Video System PaL ee eRe a Kees i i d he Wid r of afar fae Ss eee Select the Video System digital signal and TV Output analog signal TY Output Focus Bar Oo s ON OFF N E OEE Stream 1 Setting Basic Mode of Streaming 1 and Streaming 2 U Basic Mode Advanced Mode Stream 1 Setting Resolution 120K 10 O Basic Mode Advanced Mode Resolution 1820x1080 Profile Quality Video Frame Rate Profile Quality Wideo Frame Rate Wideo Format aT Video Format H2a4 RTSP Path exrrtso IP Address Audio G 711 es RTSP Path Es rtsp IP_Address Audio G 711 Stream 2 Setting Stream 2 Setting Basic Mode Y Advanced Mode Close OpasicMode Advanced Mode Close Resolution Resolution 640x480 W Profile Profile Bitrate Control Mode UO CBR WER Quality Video Quantitative z7 H Video Frame Rate Video Format RTSP Path v2 ss I ee Wideo Bitrate Wideo Frame Rate 15 FPS GOP Size GOP 15 Resolution 1280x800 1280x720 j 640
23. e Manual Date 2014 05 05 Time 17 55 59 e Server Time It shows current IP camera server time e Date Format Select the date display format e Time Zone Select your time zone It affect server time when you use NTP time e Enable Daylight Saving select the start and end daylight saving time e NTP Type in the IP address of the NTP server and interval time The time of the IP camera will be synchronized with NTP server time To use this option if the NTP Server is under WAN the IP camera must be set to access WAN Using the WAN IP that provide by your ISP provider or setup by UPnP Port Forwarding page 18 e Synchronize with PC s time In Date and Time column it shows your current PC time Click Apply to make the IP camera time the same with PC time Note that IP camera will not check with PC at every moment automatically Every time when you want to synchronize the IP camera time with PC time again please select this option and click Apply e Manual Type in the date and time and click Apply 12 TRENDnet User s Guide TV IP342Pl System gt gt User Management User Management Direct Video Stream Authentication Password Protection O YES NO Add User Username Password Confirm User List Username User Group Remove admin Administrator 1 Guest l Remove e Direct Video Stream Authentication To stream the video directly without going through the configuration page yo
24. e in IP address subnet mask gateway and DNS manually Default IP address is 192 168 10 30 if the camera doesn t connect with DHCP server DNS Domain Name System translates domain names into IP addresses Enter the Primary DNS and Secondary DNS that are provided by the ISP Network gt gt Network Setting gt gt IPv6 Setting IPv6 Setting IPv6 Enabled Manually setup the IPv6 address DHCPv 6 Enabled O Disabled IPv6 Address fe80 20f dff fe26 68f6 IPv6 is a newer numbering system that provides a much larger address pool than IPv4 which accounts for most of today s Internet traffic You can manually enter IPv6 address enable DHCPv6 to get IPv6 address automatically e Manually setup the IPv6 address You can set up IPv6 manually by enter IP Address Gateway and DNS e DHCPv6 If you have a DHCPv6 server enable this option to assign the IPv6 from server The assigned IP address will be displayed 14 TRENDnet User s Guide TV IP342Pl e IPv6 Address A virtual IPv6 address generated by the IP camera This virtual IPv6 address cannot use on WAN To access the IP camera via IPv6 address open a web browser and type in http IPv6 Address in the address bar The parentheses mark is necessary for IPv6 address Network gt gt Network Setting gt gt Port Setting Port Setting Web Page Port HTTPS Setting e Web Page Port Setup HTTP web page connecting port which is also video HTTPS Po
25. eceiver s Mail Bec Mail Bcc Mail Oo Ti ol E F ha Li Mail Port Mail Port 5 Default 25 E Enable Secure Connection TLS SSL Secure Connection E Enable Secure Connection Secure Connection OTLS SSL FTP Setting i Login Method Select Anonymous to disable the authentication feature or FTP Server pales select Account and then enter the Username and Password according to the Username mail server configuration Password Mail Server Enter the mail server address For example myserver com If you Brn are using a free mail service e g Google gmail com Yahoo Hotmail Path please enter the SMTP server address from the service provider Mode PORTE Username amp Password Enter the sender s username and password to login the ri in ee SE ex Path 20100115 121032m avi test mail server For free mail server please the email address as the username Create Che Oren Sender s Mail Enter the email address of the user who will send the email Samba Network storage Receiver s Mail Enter the mail address of the user who will receive the email Location fex Nas_ip folder Use semicolon to separate each address It can contain up to 64 characters in Workgroup the column Username Bcc Mail Enter the mail address of the blind carbon copy receiver Password Mail Port Assign the SMTP port in the text box The defau
26. er cessccsseccsecceeeeesees 37 Troubleshooting sessesesessecescesescecessecessecesosoesssoesesossesoesessecesoecesseceeee 38 Copyright 2014 TRENDnet All Rights Reserved TRENDnet User s Guide TV IP342Pl Product Overview TV IP343PI Package Contents TV IP342PI Multi Language Quick Installation Guide CD ROM Utility Software amp User s guide Power adapter 12V DC 1A 1 5M 5 ft Network cable 1 5 M 5 ft RJ 45 coupler Camera Mounting hardware Copyright 2014 TRENDnet All Rights Reserved Features The Outdoor 2MP Full HD PoE Day Night Dome Network Camera model TV IP342PI offers 15 m 50 feet night vision an IP66 weather rating tamper detection and 3x manual optical zoom for installation flexibility Record full 1080p HD video 1920 x 1080 at 30 fps in a space saving H 264 compression format Manage up to 32 TRENDnet cameras with included complimentary software and mobile apps Resolution Record 2 Megapixel Full 1080p HD 1920 x 1080 at 30 fps in the space saving H 264 compression format Multi Language Interface Support for English French Spanish German and Russian Time and Text Stamp Enable time and additional identifying text stamp overlays IPv6 IPv6 support ONVIF ONVIF v2 20 and v1 01 compliant Dynamic DNS Support Support for dyn com no ip com and iptecno com Samba Support Record video to a defined network storage device Tamper D
27. et User s Guide TV IP342PI 10 Type in the Password The default password is admin You must change the 12 Click Finish to exit the program or click Home to return to the main screen default password of the camera Enter the default password admin and enter the This device also supports the Mobile App Using your mobile device to scan the QR new password The password must be between 8 and 32 characters code to install the App Alphanumeric a z A Z 0 9 and confirm the new password by entering the Congratulations The camera is now ready to be installed in its password twice final location Change Password l Thank you for choosing TRENDnet You MUST change the default password of the camera Please install ActiveX or Plug in when you are prompted by the web browser Enter the default password admin Enter your new password must be between 8 and 32 characters Alphanumeric a z A Z 0 9 Special Characters Mobile App Admin ID Please take a moment to download our free TRENDnetVIEW App Scan the QR codes or search for TRENDnet VIEW in the Apple App Store or at Google Play for Android devices Androi Password M Change Password New password Confirm new password 11 Click the hyperlink to access to the camera s web page or click Next It is recommended that you access the IP camera now if it was using a DHCP connection Initial setup is complete are a 7 x Local
28. etection TRENDnet User s Guide TV IP342PI Receive tamper detection video clips via email ftp or save to network storage device or Product Hardware Features Micro SD card D WDR Camera Overview Improved image quality in high contrast light environments with Digital Wide Dynamic Range technology Image Rotation 90 degree and 180 degree rotation for wall and ceiling installations Motion Detection Create up to 3 motion detection windows with separate sensitivity settings and event triggers IR Lens Privacy Masks Create up to three privacy masks to conceal sensitive areas e IR Lens IR lens for the camera e Weatherproof Housing Housing is rated with IP66 Copyright 2014 TRENDnet All Rights Reserved TRENDnet User s Guide TV IP342PIl Camera Connectors SS amr d UEF u amp J A Ethernet PoE _ Power Speaker Microphone BNC GPIO Port Connector Out In Video Out Port e Ethernet PoE Port Plugs the network cable to connect to your local area network LAN If you are using the PoE you must have the network cable connect to your PoE switch or PoE Injector e Power Connector Connects the power adapter to supply power to the camera if using non PoE connection e Speaker Out Connects an external audio device such as the active speaker to deliver sound via the camera e Microphone In Connects an external microphone to receive the on the spot sound where the camera is ins
29. he Camera Setting System To configure the camera click Ra on the live screen TRENDNET a e a e aed alto E T TRENDNET Outdoor 27MP Full HD PoE Day Night Dome goonies a sirpa System Information SFTUP SNAPSHOT Server Information NETWORK MAC Address 00 0F FRF FF FF FF Server Name TV IP342PI E Status Bar AUDIO VIDEO SETTING English Francais Deutsch Espa a Language guag Poccua EVENT CONFIGURATION OSD Setting LOGOUT Time Stamp Enabled Disabled Enabled Disabled Text OSD_TY IP342Pl Text Edit Time Setting Server Time 2014 05 05 17 02 42 Date Format O yyyy mm dd mm dd yyyy dd mm yyyy Time Zone GMT 08 00 Pacific Time US amp Canada v E Enable Daylight Saving 201 AMAR 11 02 02 Slze 1920x1000 FPS 19 dell Y Shouni yt Y Suk Mir E Owens Vie wr i Rchuy Ou ON OFF System gt gt System Information gt gt Server Information w Looyraght 2014 INLNDast All Recbte Baererved Server Information MAC Address 00 0F FF FF FF FF The Web Configuration contains the settings that are required for the camera in the left Saale Son menu bar including System Network Audio Video Setting Event Setting and Logout O English Francais Deutsch Espa a Pocc ha Language To return to the live screen please click the button e MAC Address It indicates the IP Camera s MAC address e Server Name The Camera name e LED Indicator Turn the LED ligh
30. ight 2014 TRENDnet All Rights Reserved 34 TRENDnet User s Guide TV IP342PI Unscrew the meter cover on the side 4 How to Switch the Cable Access Port 1 Unscrew and open the camera s dome cover 2 Loosen the sun shield starting from one side then to the other side then take off the sun shield t 6 Twist the water proof nuts and careful remove all cables out form the bottom of the housing 3 el N 7 Insert the cable into the side of the housing 4 Remove the 2 3 and 4 cable from PCB board Copyright 2014 TRENDnet All Rights Reserved 35 TRENDnet User s Guide TV IP342PI 8 Carefully plug the 1 cable back to the PCB board 11 Put the sun shield back on 9 Then plug in the 2 and 3 cables back to PCB board 12 Secure the dome cover to the camera 10 Close the water proof nuts and meter cover Copyright 2014 TRENDnet All Rights Reserved 36 TRENDnet User s Guide TV IP342PI If Static is selected you have to manual type in the IP address Subnet Mask ae Default gat DNS 1 DNS 2 and Http Port and IP d The IP Installer is an optional utility allow you to search the cameras in your network TA OARS ik P a eee easily 1 Insert the Installation CD ROM into your computer s CD ROM drive Re Static DHCP 2 Click Exit if the Autorun pop up Name TV IP342PI 3 Goto Start gt gt type in D D is the letter assigned
31. ion detection the triggering time is according to interval setting of motion detection If it s triggered by external input alarm the triggering Daina Vitor Relay G time is according to input interval setting It triggers the external devise and lasts for 10 seconds if you select 10 in interval setting You can turn off the alarm manually by click off at the bottom right of the live screen Event Configuration gt gt Logs page System Logs Time Switch Motion Detection Logs When event occurs the camera triggers the external devise and lasts for GPIO Logs certain of time according to the output interval setting and the user is All Logs not allowed to break off the alarm manually Click Logs to see System Logs Motion Detection Logs GPIO Logs and All Logs If you remove the power from IP camera Motion Detection Logs will be cleared away 3 Output Test After the external output hardware is installed you can use the Relay Out button on the live video page to test if DO device works e On Off Switch mode Click ON the camera will trigger the external output devise For example your alarm buzzer will continuously ring You can manually break off the output signal by clicking OFF Relay Out on oFF LOGOUT e Time Switch mode Click Pulse the camera will trigger the external output devise for several seconds The duration length is according to the interval setting in Output Setting Copyr
32. lease install the vandal dome according to the instructions a The unused cable outlet hole must be closed and the waterproof connector on the used hole must be firmly locked b Werecommend the bottom of housing be set and firmly sealed on a smooth flat surface c When mounting the camera housing on a ceiling or wall please use the screws with the black rubber o rings Without the o ring water may seep into the machine Note When connecting cables into machine it is recommended to use a hose to include all the cables inside instead of plugging in several cables separately Water may seep through a gap from bundled cables You can also seal the connector hole with silicone after installation d Turn and loosen the control stick shift right and left to adjust the vari focal lens until the image becomes clear then turn and tighten the stick to fix it Copyright 2014 TRENDnet All Rights Reserved TRENDnet User s Guide TV IP342Pl 1 a Camera Installation Insert the Installation CD ROM into your computer s CD ROM drive to Auto Run program Click the Install Camera TRENDNET Select your language Install Camera Install TRENDnet VIEW Pro Software Quick Installation Guide User s Guide E S PAD A gt sj Outdoor 2MP Full HD PoE Day Night Dome Network Camera TV IP342PI Product How Tos Product Registration Write down the MAC ID of the camera Write down the MAC addre
33. lows the camera to do WAN access In the address bar of browser key in https router WAN IP external web port to access the IP camera Network gt gt Network Setting gt gt RTSP Setting RTSP Setting Network gt gt Network Setting gt gt UPnP RTSP Server OEnabled Disabled RTSP Authentication UPnP RTSP Port 5000 1024 9997 9000 1027 10000 UPnP tEnabled ODisabled UPnP Port Forwarding OEnabled Disabled RTP Start Port RTP End port Eternal Weh Port C lt The router doesn t support UPnP Port Forwarding e RTSP Server External HTTPS Port 443 Enable it then you can access camera and get image via RTSP protocol External RTSP Port 554 lt The router doesn t support UPnP Port Forwarding gt Copyright 2014 TRENDnet All Rights Reserved 15 TRENDnet User s Guide TV IP342Pl If you have a media player that supports RTSP protocol you can use it to receive the video streaming from IP camera The RTSP address can be set for two streamings respectively e RTSP Authentication Disable means everyone who knows your camera IP Address can link to your camera via RTSP No username and password are required Under Basic and Digest authentication mode the camera asks the user to give username and password before allows accessing The password is transmitted as plain text under basic mode which provides a lower level of security than under digest mode Make sure you
34. lt SMPT port is 25 ee OE e E E Test For the free mail service please enter the correct port number from the service provider Copyright 2014 TRENDnet All Rights Reserved 23 TRENDnet User s Guide TV IP342Pl Secure Connection If the mail server requires an encrypted connection you should select the SSL option TTLS is an extension to plain text communication protocols It offers a way to upgrade a plain text connection to an encrypted TLS or SSL connection Click Apply to save the setting then use Test button to test the server connection A message box will tell you OK if it works and a test e mail will be sent to receiver s mail address e FTP Setting FTP Setting FTP Server Username Password Port Path Mode ex Path 20100115 121032m avi Create the folder FTP Server Enter the IP address of the target FTP server Username amp Password Enter the username and password to login into the FTP server Port Enter the port number used for the FTP server Path Enter the destination folder for uploading the images For example 342PI Mode In PORT mode the FTP server builds the connection to the user s data port actively However from the user side firewall s standpoint the action of connecting from FTP server is often considered to be dangerous and should be blocked In PASV mode the problem is solved The FTP server waits for the data transmission con
35. makes DI and GND pin disconnected the camera input alarm is triggered and then camera will execute the action user has set for example send snapshot to E mail address Copyright 2014 TRENDnet All Rights Reserved Normal 5V 5V Triggered OV GPIO PIN definition GND Ground Initial state is LOW DO Digital Output DC 5V DI Digital Input Max 50mA DC 5V 2 GPIO Setting Event Configuration gt gt GPIO Setting gt gt Input Setting Input Sensor According to your external device and circuit design select N O normally open or N C normally closed Input Action When the camera input alarm is triggered it can trigger the relay out or send the video to E mail FTP SAMBA Interval If you select 10 sec here once the input alarm is detected and action is triggered it cannot be triggered again within 10 seconds Based on the schedule When click the option box only during the selected schedule time the I O is enabled That is for example the 11th hour of Monday has not been colored in the schedule table then no action will be triggered even the camera detects input signal during 11 00 12 00 on Monday 33 TRENDnet User s Guide TV IP342PI Event Configuration gt gt GPIO Setting gt gt Output Setting e Mode Setting On Off Switch When event occurs the camera triggers the external devise and lasts for certain of time according to the event interval setting If it s triggered by mot
36. nection built by the user Make sure that the server supports the mode you select Copyright 2014 TRENDnet All Rights Reserved Create the folder Select Yes then folders will be created folder by date under your FTP path Click Apply to save the settings then click Test button to test the server connection A message box will tell you OK if it works and a test file will be uploaded to FTP server Samba Setting Samba Network storage Location RE 6 W2s_ip older Workgroup l ex Path 20100115 121032m avi Create the folder Location Enter the path of the shared folder Workgroup Type in the workgroup name of the computer Username amp Password Enter the username and password to login into the Samba Create the folder Select Yes then folders will be created by date under your Samba Server Click Apply to save the setting then use Test button to test the server connection A message box will tell you OK if it works and a test file will be created in the location 24 TRENDnet User s Guide TV IP342PI AUDIO VIDEO SETTING Audio Video Setting gt gt Image Setting Image Setting LIVE VIEW Image Setting NETWORK AUDIO VIDEO SETTING EVENT CONFIGURATION Privacy Mask Privacy Mask Image Setting Brightness Contrast oO Image Setting Hue Brightness Saturation Contrast Sharpness ia Hue H i AGC Shutter Time
37. nge a program Map network drive gz a Hard Disk Drives 1 Acer C Libraries a Poceeests y a Music 116 GB free of 187 GB Pictures Videos 4 Devices with Removable Storage 2 DVD RW Drive D TV IP302PI Removable Disk E y e jm Computer N 615 MB free of 702 MB MF 6 28 GB free of 7 45 GB Workgroup WORKGROUP Memory 2 00 GB Processor AMD E 350 Processor is _ g ER Te Z Organize v Save search os Name Date modified Type pv Libraries Documents Pi Music p Search again in Pictures G Libraries Custom Internet p File Contents z Videos p 1 item Search for the additional ActiveX or plug in files listed below and delete them to completely uninstall the ActiveX control or plug in from your computer np_hoem_x dll 6 10 2013 6 15PM Application extens m Copyright 2014 TRENDnet All Rights Reserved e avcodec 53_v1 8 dll e avutil 51_v1 8 dll e swscale 2_v1 8 dll e WEBWATCH2 e WEBWATCH 2 o0cx forgot my password What should I do Please follow the steps below to reset to factory default setting a Remove the power and network cable b Remove the cover of the camera c Press and hold the reset button for 10 seconds and wait for the camera to finish rebooting up to 2 minutes d Run the install camera wizard from the CD ROM to login to the camera 39 TRENDnet User s Guide Limited Warranty Limited Warranty
38. o back up the camera configuration file that will be saved on the local computer A password is required to save a configure file You will need to enter the same key when restoring the configure file to the camera Restore Click Browse to select the configure file from your computer then click Restore to restore all setting A previous saved password on this configure file is required to restore configure file NETWORK Network Setting IP Address Setting DHCP Static NETWORK IP Address 192 168 10 30 Network Setting Subnet Mask 255 255 255 0 Advanced Gateway 192 168 10 1 HTTPS SNMP DNS 1 192 168 10 1 IP Address Filter DNS 2 QoS DSCP IPv6 Setting IEEE 802 1x IPv6 Enabled PPPoE amp DDNS E Manually setup the IPv6 address Event Server DHCPv6 Enabled O Disabled IPv6 Address AUDIO VIDEO SETTING fe80 20f dff fe26 9a30 Port Setting EVENT CONFIGURATION Web Page Port HTTPS Port 443 HTTPS Setting pouT Web Authentication Authentication UPnP UPnP tEnabled ObDisabled Copyright 2014 TRENDnet All Rights Reserved Network gt gt Network Setting gt gt IP Address Setting IP Address Setting 9 DHCP Static IP Address Subnet Mask Gateway DNS 1 DNS 2 e DHCP Select this option when your network uses the DHCP server When the camera starts up it will be assigned an IP address from the DHCP server automatically e Static IP Select this option to typ
39. o device wishing to attach to a LAN or WLAN To use this 1 Update Schedule DDNS will be updated automatically The time range is from 60 to 5000 minutes If you do not wish to obtain updates enter 0 function you need a device to build IEEE 802 1x LAN at first 2 For dyn com and 3322 orq it is recommended that updates are done once per day 1440 minutes Your account may be blocked if frequent updates are detected The EAPOL protocol support service identification and optional point to point encryption over the local LAN segment Please check what version of the authenticator and authentication server support This Camera supports EAP TLS method Please enter ID password issued by the CA then upload related certificates Copyright 2014 TRENDnet All Rights Reserved 21 TRENDnet User s Guide TV IP342Pl PPPoE PPPoE Setting Enable Enabled QO Disabled Username Send mail after PPPoE aoe E Enabled Subject PPPoE_TV IP343PI Select Enabled to use PPPoE Type in the username and password for the ADSL connection Send mail after dialed When successfully connecting to the internet it sends a mail to a specific mail account As for the mail account setting please refer to Server setting page DDNS DDNS Setting Enable Enabled O Disabled Provider www noip com V Hostname Username Password Schedule Update This camera supports following Dynamic DNS server Dyndns com 3
40. ome Network Camera b See n IV IP342P1 SNAPSHOT Lopyrqht 2014 INLNDest All gits Bararved The live screen of the IP camera configuration provides you with many useful information and functions including SETUP Click the button to configure the camera SNAPSHOT Click the button to take a snapshot The snapshot will pop up another window for your review first Right click the mouse to save the snapshot at the desire destination System Information It shows current system Date Time Video Resolution and Video Refreshing Rate Digital Zoom The drop down menu has 3 images size available 1 2x 1x and 2x The default is 1 2x Streaming Profile Use the drop down menu to select Streaming 1 amp Streaming 2 video If the streaming 2 setting is closed on AUDIO VIDEO SETTING gt gt Video this option will not appear TRENDnet User s Guide TV IP342PI Speaker Microphone Click the Mic to speak out through the camera Click the Speaker to receive the on side sound and voice from the camera D Online Visitor It shows how many people connect to this IP camera Relay On Click the Relay out ON to trigger the relay output for testing click Off to stop triggering To switch between these two types of relay out please refer to Sy F Enable digital zoom Zoom Factor 299 Event Configuration gt gt GPIO Setting session for detail Logout Click to logout the camera One the live view video right
41. r ONVIF version The two devices that use ONVIF to communicate should be set to the same version e Security Select Disable then the username and password are not required when accessing the camera via ONVIF Select Enable then username and password are necessary e RTSP Keepalive When the function is enabled the camera checks once in a while if the user who links to the camera via ONVIF still keeps connecting If the connection had been broken the camera stops transmitting video to user Network gt gt Network Setting gt gt Bonjour Bonjour Bonjour Enabled ODisabled TV IP343PI This function enable Safari browser s bookmark to link to this IP camera The Bonjour Bonjour Name name is the name that display in the bookmark Please note the Bonjour function on 16 TRENDnet User s Guide TV IP342Pl Safari browser does not support https protocol If you selected https mode you will see the camera appears on Safari s bookmarks but will not be able to access the camera Network gt gt Network Setting gt gt LLTD LLTD Link Layer Topology Discovery LLTD OcEnabled Disabled If your PC supports LLTD enable this function then you can check the connection status properties and device position like IP address of this IP Camera in the network map In Windows Vista or Windows 7 you can find LLTD through the path Call out the Control Panel gt Network and Internet gt Network and Sha
42. r media player supports the authentication schemes e RTSP Port It s used for TCP connection Setup port for RTSP transmitting Default 554 e RTSP Start and End Port It s used for UDP connection Setup port for RTSP transmitting Default 5000 9000 Network gt gt Network Setting gt gt Multicast Setting Based on the RTSP Server Multicast Setting Based on the RTSP Server Stream 1 IP Address 234 5 6 78 224 3 1 0 239 255 255 255 6000 1 65535 1 255 Stream 2 IP Address 234 5 6 79 224 3 1 0 239 255 255 255 6001 1 65535 1 255 Multicast is a bandwidth conservation technology This function allows several users to share the same packet sent from IP camera To use Multicast appoint IP Address and port here TTL means the life time of packet The larger the value is the more users can receive the packet Copyright 2014 TRENDnet All Rights Reserved To use Multicast be sure to enable the function Force Multicast RTP via RTSP in your media player Then key in the RTSP path of your camera rtsp IP address to receive the multicast Network gt gt Network Setting gt gt ONVIF ONVIF ONVIF Ov2 20 v1 01 Disabled Security OcEnabled Disabled RTSP Keepalive OcEnabled Disabled Under ONVIF connection the video will be transmitted by RTSP Be sure to enable the RTSP server in IP setting or you re not able to receive the video via ONVIF e ONVIF Choose you
43. ring Center gt Click See full map Network gt gt Advanced gt gt HTTPS When the users access cameras via Https protocol the transmitted information will be encrypted so that the security level is arisen You can select the connection type e Http user can access the camera via Http path e Https user can access the camera via Https path but cannot via Http path e Http amp Https Both the Http and Https path can be used to access the camera When you change the setting of connection type it may cause connection error or disconnection error if you switch the protocol directly Therefore Http amp Https mode is necessary If you want to change from Http to Https please switch to Http amp Https mode first and then switch to Https mode Same method when you change from Https to Http The Https protocol has certificate verifying mechanism When the user access a website via Https the browser will check the certificate of that domain and verify its trustiness and secure Certificate generation process Copyright 2014 TRENDnet All Rights Reserved 1 2 Remove the existing certificate Before you generate a new certificate please remove existing one Select Http connection type and click Remove If a dialog box pops up to ask you to confirm click Yes HTTPS Setting Created Request Subject C TW ST L O OU CN Date 2014 Mar 12 16 56 10 Installed Certificate
44. rk connection was broken down The camera will send trap messages after the network being connected again V3 Authentication Failed A SNMPv3 user account tries to get authentication but failed Due to incorrect password or community 19 TRENDnet User s Guide TV IP342Pl Network gt gt Advanced gt gt IP Address Filter IP Address Filter Setting E Enable ip address filter O Allow Deny address M IPv4 Setting IPv4 List No IP Address Filter E Always allow admin IP address access to this device Admin 1 address D deny an IP address or even a range of the IP address to access the IP camera If you ou can allow or would like to deny a range of IP address but would allow an IP within that range can access the camera please setup the allow IP address in the 1 priority and set the deny range of IP address as 7 priority as example below IPv4 List No IP Address Filter a LT b PAA S o D D allow 2 192 168 1 1 192 168 1 254 deny Copyright 2014 TRENDnet All Rights Reserved Network gt gt Advanced gt gt QoS DSCP QoS DSCP Setting E Enable QoS DSCP Live Stream 0 63 oe o S DSCP specifies a simple mechanism for classifying and managing network traffic and Event Alarm Management provide QoS on IP networks DSCP is a 6 bit in the IP header for packet classification purpose The number 0 63 for Live Stream Event Alarm and Management represent the ratio
45. rt transmitting port Default 80 e HTTPS Port Setup HTTPS connecting port Default 443 Network gt gt Network Setting gt gt Web Authentication Web Authentication Authentication The camera supports two levels of authentication Basic and Digest The Basic option having the username and password transmitted as plain text The digest option encrypted username and password during data transmission The default authentication is set to Digest UPnP This IP camera supports UPnP Universal Plug and Play which is a set of computer network protocols that enable the device to device interoperability UPnP Port Forwarding When the camera is installed under a router enable UPnP Port Forwarding to let the router open ports so that the video streams can be sent out from a LAN Set Web Port Https Port and RTSP port and make sure your router supports UPnP and the function has been activated After type in the port number and click Apply the port forwarding status will display beside the port column There are three status will show Registered successfully UPnP port forwarding setting succeeds The router doesn t support UPnP Port Forwarding The camera can detect the router but router return a message that it does not support UPnP Port Forwarding The router is with some problems Please reboot it The camera cannot detect the router Please check your router If this router has a WAN IP this function al
46. ss of your camera This information is required in the installation process The MAC address is located on the camera label shown in photo below MODEL TV IP342PI DC12V 1A cE Fe S N 1234567890123 v Kudane 4 x HIW V1 0R F W V1 XX XX FF MAC FFFFFFFFFF AMUI ce raman sae Copyright 2014 TRENDnet All Rights Reserved initiate the 4 5 Plug in and connect the power adapter to the camera If you are using the PoE to supply power to the camera please skip to the next step Click Next when you are done Power up the camera lf using PoE to supply power to the camera please skip to the next step Plug in and connected the power adapter to the camera The IR LEDs will be on and you can see dim visible red light Allow 60 seconds for the camera to boot up Connect a network cable to the camera s network port and then to your router If you are using PoE please ensure the cable is connected to a PoE switch or PoE injector Connect the network cable Connect a network cable to the camera s network port and then to your router or PoE Switch If you are using PoE the IR LEDs will be on and you can see dim visible red light Allow 60 seconds for the camera to boot up TRENDnet User s Guide TV IP342Pl 6 Wait while searching the cameras Please wait while the wizard searches for your camera 7 The founded cameras will show on the screen The camera already selected by default
47. surances are added when developing SNMPv3 The user has to give not only the security name similar with community name in v1 amp v2c but the password in order to access the IP camera Please set security name authentication type authentication password encryption type encryption password of write and read respectively The security Copyright 2014 TRENDnet All Rights Reserved name can be any English characters and numbers and must be shorter than 31 letters The password must be 8 64 letters in length Different from in SNMPv1 and v2c the user have to create an account when using SNMPv3 In the account parameters key in the security name and password you set in the camera to get accessing SNMPv1 SNMPv2 Trap E SNMPv1 v2c Trap Trap Address E Cold Start E Setting Changed E Network Disconnected E V3 Authentication Failed E SD Insert Remove Trap Community Trap Event Trap is a mechanism that allows a managed device to send messages to the manager instead of waiting passively for polling from the manager Specify the trap event When those events occur the camera will send the ring message to the Trap Address which is usually the manager s IP address Trap Community means the community that can receive the trap message Note Trap Address must be under the same LAN with IP camera Cold Start The camera starts up or reboots Setting changed The SNMP setting is changed Network Disconnected The netwo
48. t on or off by click the ON OFF button e Language There are 5 languages options When changing the language it will prompt dialogue box for confirmation Click Yes to proceed Copyright 2014 TRENDnet All Rights Reserved 11 TRENDnet User s Guide TV IP342PIl System gt gt System Information gt gt OSD Setting OSD Setting Time Stamp Enabled O Disabled Enabled O Disabled i OSD_T IP343P Text Edit e Time Stamp Enable or disable the time that will show on the live screen Position After enabling time stamp you can select the position of time stamp on the live screen OSD Setting Time Stamp Enabled Disabled Enabled Disabled Text OSD_TY IP342Pl Text Edit e Text Enable the Text option to have the desire text show on the camera live screen Text Edit Click it to call out text edit window Text Key in the words you want to show on the live screen Opaque Set the background transparency of the text Text Settings Text OSD_TV IP342PI Opaque Size T2 Y Copyright 2014 TRENDnet All Rights Reserved System gt gt System Information gt gt Time Setting Time Setting Server Time 2014 05 05 17 13 01 Date Format O yyyy mm dd mm dd yyyy dd mm yyyy Time Zone GMT 08 00 Pacific Time US amp Canada E Enable Daylight Saving O NTP NTP Server pool ntp org Update E Time Shift ooo Synchronize with PC s time Date Tim
49. t the image will get brighter and moving subjects might be blurred Sense Up option is only enabled when users select outdoor or indoor in shutter time option D WDR Digital Wide dynamic range This function enables the camera to reduce the contrast in the view to avoid the dark zones resulting from over and under exposure Video Orientation Flip mirror or rotate the image Day amp Night The camera can detect the light level of environment If you choose Light Sensor Mode the image will be turned to black and white at night in order to keep clear To set light sensor mode appoint a lux standard of switching D N here Current lux value is provided for reference Under Times Mode the switch Copyright 2014 TRENDnet All Rights Reserved time of Color Black and white is according to the given time If you select Synchronize with DI input the image turns to black and white when digital input is triggered You can also control it by choosing Color or B W e White Balance Adjust the Red Blue gain values e Denoise This function is able to filter the noise and blur from the image and show a clearer view 3D and 2D filer values can be adjusted Note When you select a number in Shutter Time actually the shutter time varies in a range and controlled by camera automatically Following table shows the shutter time option and corresponding range Option Shutter Time Range sec Outdoor 1 10000 Selected num
50. talled e BNC Video Out Connect a CRT monitor or handheld monitor e GPIO Port Connect external device Please refer to I O setting paragraph It s also used for IP camera reset Please refer to Factory Default paragraph Copyright 2014 TRENDnet All Rights Reserved Installation Hardware Installation Viewing Angle Choose a location that has good angle to shoot the image you expect to see The motion detection area should also be considered when installing the camera Manual Pan Tilt The camera can manual pan tilt to your desired location Pan 360 Rotate 172 Tilt 30 90 Vari Focal Lens The camera equipped with external vari focus lens control Achieve clear focus by adjusting the zoom focus button Zoom Focus TRENDnet User s Guide TV IP342PI Waterproofing e Before closing the dome cover make sure that the black rubber band sticks to the inside of the cover completely If the rubber band is crooked or uneven it may The camera is designed to be waterproof However you need to protect the connectors cause the camera to no longer be waterproof from water damage For example you can tape the junction points of the connectors while you connect the cables or purchase a weatherproof cable power cord protector f Lock the screws on the dome cover tightly to ensure there s no gap between the lid and the base Vandal Dome Installation Tips In order to ensure IP66 waterproof level p
51. to your CD ROM Drive and then 192 168 1 175 press the ENTER IP Address 4 Click IPInstaller Folder and click IP Installer exe Saag 209 299 299 0 Default 192 168 1 254 DNS 1 5 The main screen will pop up DNS 2 Http Port O 80O MAC Account Device lists fDevice Name IP Address MAC Adress O Static DHCP TV4P343PI 192 168 11 1 00 18 1A 0C 2B BNEW TV4P342PI TV 4P342PI 192 168 1 175 00 30 4F 00 29 A9 n TV IP343PI 192 168 50 1 00 0F 0D 26 41 40 MMMM ea e a Subnet Mask Default 192 168 1 254 DNS 1 DNS 2 168 95 192 Http Port a 80o Password Access Camera MAC _90 30 4F 00 29 43 Account Po Password Fc el e Exit Exit the IP Installer Utility To change the IP Camera name and IP address information 1 Select the IP camera in the list 2 Change the network parameters on the right 3 Click Change to apply the changes 4 Click Search 5 Select the IP camera in the device list 6 Click Access Camera to login to the IP camera s web browser configuration e Search Search the IP Camera within the Network e Access Camera access the selected camera s web page e Change change the selected camera s IP address via Static IP or DHCP Copyright 2014 TRENDnet All Rights Reserved 37 TRENDnet User s Guide TV IP342PI Trou bleshooting 2 The autorun program is unable to detect my camera What should I do a Verify that you ha
52. tter compression way and the file may be smaller However the VBR file size cannot be predicted The image may become broken or lagged when your bandwidth is not enough for the data quantity you selected Copyright 2014 TRENDnet All Rights Reserved Video Quantitative The quality parameter of VBR You can choose 1 10 compression rate The higher the value is the higher the image quality is Video Bitrate The quality parameter of CBR You can choose 32kbps 8Mbps The higher the value is the higher the image quality is Video Frame Rate The video refreshing rate per second The max value is affected by the input resolution you choose GOP Size It means Group of Pictures The higher the GOP is the better the quality is Video Format H 264 or M JPEG RTSP Path RTSP output connecting route You can use the RTSP address displaying beside the column to access this IP camera 3GPP Streaming mode 3GPP Streaming Setting Disabled 3 ex rtsp IP_Address v3 Audio AMR 9 Enabled Resolution Video Bitrate Video Frame Rate Video Format RTSP Path 3GPP Streaming is designed for specific mobile viewing To receive video via 3gpp please remember to enable rtsp server in the Network Setting page Resolution 640x480 320x240 or 176x144 Quality The higher the quality is the bigger the file size is It might affect Internet transmitting speed if the file gets too large Video Bitrate
53. u can access it via Internet Stream 1 Video Stream 1 Video e Enable Password Protection Yes User needs to enter user name and password to stream the camera No User can stream the camera without entering the username and password e Add user Enter the username and password to add guest users to access the camera The guest user can only view the live view video and is not allowed to do any configuration Copyright 2014 TRENDnet All Rights Reserved e User List List all users that were added into the camera Click Edit to modify the user information Click Remove to remove the users from the list System gt gt Tools Tools Firmware Upgrade Firmware Version V1 03 33 ES New Firmware System Reboot Click the Reboot button to reboot your IP Camera Factory Reset Click the Reset button to reset to factory default settings Configuration Save the device configurations to your local hard drive Backup Password Pssw ord ae eS EOSS e Firmware Upgrade To update the firmware click Browse to select the firmware then click Upgrade to proceed Please do not disconnect power or Network cable during firmware upgrading e System Reboot Click Reboot to reboot the IP camera e Factory Reset Click Reset to reset all the settings back to factory default value e Configuration 13 TRENDnet User s Guide TV IP342PIl Backup Click Backup t
54. ve followed all the steps in Section 2 Hardware 1 linserted the Utility CD ROM into my computer s CD ROM Drive but the installation menu does not appear automatically What should do b Installation Disable any software firewall programs such as ZoneAlarm or Norton Internet Security If you are using Windows 8 7 Vista or XP disable the Windows 8 8 1 If the installation menu does not appear automatically press the windows icon built in firewall c Reset the IP Camera ll and press r simultaneously In the run box type D autorun exe where Run the Autorun program from the CD ROM again D in D autorun exe is the letter assigned to your CD ROM Drive and then press the ENTER key on your keyboard 3 I do not have a DHCP server or DHCP is disabled on my network and am unable Windows 7 to configure the TV IP343PI What should I do If the installation menu does not appear automatically click on the Windows Icon on the bottom left hand corner of the screen click the Search programs a Go to the TCP IP settings on your computer and assign a static IP address on your computer s network adapter in the subnet of 192 168 10 x Since the default IP address of the TV IP343PI is 192 168 10 30 do not assign a static IP address of 192 168 10 30 on your computer s network adapter and files box and type D autorun exe where D in D autorun exe is the letter assigned to your CD ROM Drive
55. x480 320x240 or 176x144 Video Format H24 gt Quality The higher the quality is the bigger the file size is It might affect Sastry ENN x rtsp 1P_Address v2 Audio G 711 Internet transmitting speed if the file gets too large Video Frame Rate The video refreshing rate per second The max value is 3GPP St ing Setti reaming Setting affected by the input resolution you choose Enabled Disabled Video Format H 264 or M JPEG Copyright 2014 TRENDnet All Rights Reserved TRENDnet User s Guide TV IP342Pl RTSP Path Set the RTSP output connecting route You can use the RTSP address displaying beside the column to access this IP camera Advanced Mode of Streaming 1 and Streaming 2 Stream 1 Setting 9 Basic Mode Advanced Mode Resolution 1920x1080 Profile Quality Video Frame Rate Video Format RTSP Path ex rtsp IP_Address Audio G 711 Stream 2 Setting Basic Mode 9 Advanced Mode Close 640x480 9 CBR VBR Resolution Profile Bitrate Control Mode Video Quantitative Video Bitrate Video Frame Rate GOP Size Video Format RTSP Path ex rtsp IP_Address v2 Audio G 711 Resolution 1280x800 1280x720 640x480 320x240 or 176x144 Bitrate Control Mode In CBR Constant Bit Rate mode the bitrate keeps consistent all over the video In VBR Variable Bit Rate mode the bitrate changes with the complexity extent of the video data VBR provides a be

TRENDnet User`s Guide Cover Page

Contents

Download Pdf Manuals

Related Search

Related Contents