XTREME VALUE TOWER SERIES (XVT) USER`S MANUAL
Contents
1. EBP s daisy chain to UPS or other 44 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS 3 The AC input cord is for connecting AC utility to operate the Charger contained in each EBP 4 The input AC Circuit Breaker will trip to the OFF position in the event that the internal EBP charger draws excessive current Extended Battery Pack Installation CAUTION Extended Battery Pack EBP Installation should be performed by qualified service personnel 1 Verify that the DC circuit breaker on the rear panel of the EBP is in the OFF position 2 Turn the UPS OFF and disconnect the UPS Input Cord from the AC wall outlet 3 Remove the EBP connector cover from the UPS rear panel 4 Connectthe external DC battery cable from the EBP to the appropriate connector on the UPS 5 Secure the DC battery cable to both the rear of the UPS and the rear of the EBP by using M3x8 screws provided 2 each per connector end 6 Repeat the above procedure for testing and securing each additional EBP required CAUTION Do not use extension cords when connecting input AC power to UPS or EBP s 7 Move the DC circuit breaker on the rear of each to the ON position At this point the UPS will need to be started 8 If the EBP s are plugged into an AC source and properly installed the internal batteries will be charged when acceptable voltage is present EBP s must be charged for a minimum of 62. O e EXr BATTERY Hate The musi be connected the power wiih the grounding mimimmmmmmmmamam LILILILILILILILILJLILILILI noooooooooooo LILILILILILILILILILILILILI NXRTi EBP3 REAR VIEW 41 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS BATTERYPACK BATTERYPACK NXRTi 1000 WITH 2 NXRTi EBP1 42 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS CHARGING LED BAITERY TEST LED BATTERYPACK NXRTi EBP FRONT PANEL LED Description The Charging LED GREEN indicates that the battery charger in the Extended Battery Pack is charging normally with the AC power cord attached to the Battery pack The Battery Test LED GREEN indicates that the DC output of the Extended Battery Pack EBP is normal To perform the Battery Test e switch the breaker on the rear of the to ON position e press the Battery Test Button on the front panel of the e the DC output from the is normal when the Battery Test LED is illuminated Prior to connecting EBP s test each EBP to assure proper operation Extended Battery
3. use the ECO mode when the quality of the input AC utility is not stable 31 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS MAINTENANCE Only minimum maintenance is required for this series of UPS The battery is sealed lead acid maintenance free It only needs to be kept charging to obtain the expected life Whether it is started or not the UPS would charge batteries once it is connected to utility power and provide protection for over charging and deep discharging BATTERIES The life of batteries used in these UPS products is estimated at 3 6 years depending on level of usage Once the battery is no longer useful and must be replaced please contact service personnel for assistance REPLACING THE BATTERY QUALIFIED SERVICE PERSONNEL ONLY CAUTION Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery Service the battery under the supervision of Qualified Service Personnel knowledgeable of batteries and their precautions CAUTION use only the specified type of battery See your dealer for replacement batteries CAUTION rne battery may present risk of electrical shock Do not dispose of batteries in a fire as it may explode Follow all local ordinances regarding proper disposal of batteries CAUTION po not open or mutilate the batteries Released electrolyte is harmful to skin and eyes and may be toxic CAUTION Although the battery system voltage i
4. e Enter the setting interface Press and hold the function setting key for more than 2 seconds the letters ECO will flash as following 111 Letters flash Enter the ECO setting interface Press and hold the function setting button for more than 7 second but less than 2 seconds then come to setting interface of ECO the letters ECO will light for a long time The ON below the ECO will flash Press and hold the inquiring button C DO for more than second but less than 2 seconds to determine whether the ECO function is used or not If used the corresponding word is ON if not the word is OFF 24 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS Letters flash e Confirm the ECO setting function After selecting ON or OFF press and hold the function setting button for more than 2 seconds The ECO setting function is now completed and the ON or OFF below the ECO will light without flash e Exit from the setting interface Press and hold function setting button for more than 2 seconds exit from the setting interface and return to the main interface Bypass Output Setting e Enter the setting interface Press and hold the function setting button for more than 2 seconds Press and hold the function setting button for more than second but less than 2 seconds select the function setting choose the byp
5. prove to be fatal PRODUCT DESCRIPTION Many different kinds of sensitive electrical equipment can be protected by an Uninterruptible Power Supply UPS including computers workstations process control systems telecommunications systems sales terminals other critical instrumentation etc The purpose of the UPS is to protect these systems from poor quality utility power complete loss of power or other associated problems Electrical interference exists in many forms causing problems in AC power from lightning power company accidents and radio transmission motors air conditioners and vending machines Protection of sensitive electrical equipment is vital to protect against power outages low or high voltage conditions slow voltage fluctuations frequency variations differential and common mode noise transients etc To prevent power line problems from reaching critical systems causing damage to software hardware and equipment malfunctions the UPS maintains constant voltage isolating critical load output and cleaning the utility AC power 6 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS Double Conversion On Line Technology A double conversion on line technology UPS provides completely isolated clean uninterrupted single phase power to your critical systems while maintaining the batteries for their maximum potential In the event that the power failure lasts longer than the UPS b
6. 8 hours recharge battery heck th f Short back up time UPS overload Check the usage of loads remove some redundant devices When replace battery contact Battery aged franchiser to get battery and relative assembly T Press and hold the ON key for more Sore than 1s to start UPS UPS doesn t startup UPS has no battery after pressing the ON Connected or battery button voltage low and too many loads connected Fault occurs inside UPS Contact supplier for servicing Charger doesn t work normally or battery aged The voltage or frequency The INPUT letters of utility power exceeds on LCD display UPS input range Connect UPS battery well if battery voltage low please turn off UPS and take off some loads then start UPS The icon of charger status on LCD display flashes and buzzer beeps once per second Contact supplier for servicing 35 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS SPECIFICATIONS MODEL NXRTi 1000 NXRTi 2000 NXRTi 3000 BYPASS VOLTAGE RANGE 186VAC 252VAC HARMONIC DISTROTION 596 NON LINEAR LOAD PHASE SINGE PHASE GROUNDED RATED VOLTAGE 208 220 230 240VAC FREQUENCY 50 60 HZ 0 2 OUTPUT OVERLOAD CAPACITY 15096 for 30 sec 200 for 300ms EFFICIENCY gt 0 VOLTAGE 24VDC 48VDC 72VDC HOLDOVER TIME 5 MIN FULL LOAD 12 MIN HALF LOAD CHARGE CURRENT CURRENT 2 STRINGS OF 2 STRINGS OF 2 STRINGS OF ENSE 70
7. AND OR BATTERY PACK WILL VOID THE WARRANTY All EBP s have a different DC voltage configuration intended only for the UPS s listed above PLEASE DO NOT MIX EBP s AND MAKE SURE YOU ONLY CONNECT THE EBP TO LIKE EBP s OR UPS INDICATED ABOVE DC VOLTAGES ARE MARKED ON BOTH THE UPS AND THE EBP MAKE SURE THEY MATCH CAUTION CHECK VOLTAGE PACK BEFORE CONN CAUTION LABEL ON EBP CABLE CONNECTORS PLEASE CHECK VOLTAGES CAREFULLY 40 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS BREAKER ExT BATTERY e _ a of o mE INPUT Eee EM 0000000000000 Game amp O ass NOOOOOOOOOo0o0o TSS IL IL IE IL OL CILJE e o wn 5 x A citer NXRTI EBP1 REAR VIEW 5 gt o LICIEJEICIEJ entiers LILILILILIL LILILIEILJE pyaar OOO000 OOOO DODO Q DO LILILILILILI o LILILILILILI gogogo DODOCOO 5 I pem timet m 9 D 9 re fe NXRTi EBP2 REAR VIEW pO BREASER 3AIZ5OVaD uy WS
8. DC battery cable to the rear of the UPS and the rear of the EBP by using M3 x 8 screws provided 2 each per connector end Connect the input power cord from the EBP to an input AC utility source per specifications Connect a second battery pack to the first EBP in the same fashion if more than one is to be installed Refer to Appendix A Battery Pack User Manual for more details Connect SNMP card option Remove the two screws securing the SNMP cover plate on the rear of the UPS and slide the SNMP NetAgentll card into the slot Secure the card into the slot with the two screws previously removed Close the battery breakers on the Optional battery packs if installed Connect the AC input cable to the UPS and connect the other end to an approved grounded outlet Once the UPS has been connected to an AC power source the internal charger will start charging the UPS batteries at this point the yellow LED is illuminated and the LCD displays UPS OFF In this state the output voltage is zero which means UPS has no output Please realize that although you may start using the UPS immediately maximum back up time will still not be available so it is recommended to charge the batteries for a minimum of 6 hours before use Start and configure the UPS ON OFF ROTATE SYSTEM TEST MUTE FRONT PANEL BUTTONS 20 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS e ON OFF BUTTON Press and hold button s
9. STATED ABOVE IN NO EVENT WILL XPC Corporation BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF Xtreme Power Conversion EQUIPMENT including but not limited to any costs lost profits or revenue loss of equipment loss of use of equipment loss of software loss of data cost of substitutes or claims by third parties Purchaser s sole and exclusive remedy for breach of any warranty expressed or implied concerning Xtreme Power Conversion equipment and the only obligation of XPC Corporation under this warranty shall be the repair or replacement of defective equipment components or parts or at XPC Corporations sole discretion refund of the purchase price or substitution of an equivalent replacement product 39 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS APPENDIX A EXTENDED BATTERY PACK USER GUIDE Estimated Run Time for UPS with Extended Battery Packs RUNTIME FOR OTY OF EXTENDED BATTERY PACKS IN MIN VA warts ues tms G EBP 5 EBP MODEL Note for estimated run times using more than 5 EBP s contact Xtreme Power Conversion at support xpcc com CAUTION It is very critical to connect the correct voltage EBP with the UPS intended NXRTi EBP1 is for NXRTi 1000 NXRTi EBP2 is for NXRTi 2000 NXRTi EBP3 is for NXRTi 3000 CONNECTING THE INCORRECT BATTERY PACK TO THE UPS MAY RESULT IN DAMAGE TO THE UPS
10. Time when the utility power fails or returns e UPS has a Bypass Function that allows for the load to be transferred to a bypass mode when a UPS fault occurs No interruption in power occurs to the load and an alarm will alert to this occurrence This feature also allows for configuring the UPS to support fully rated loads of switching power supplies as the bypass circuit can handle the start up Advanced Voltage Compensation Technology allows the input voltage range to be 115VAC to 295VAC reducing battery usage and enhancing UPS response during utility power fluctuations Advanced Wide Input Frequency Technology enables the UPS to perform from 45 to 55 Hz when 50Hz output is selected or 55 to 65 Hz when 60Hz output is selected All of this means that the UPS is very compatible with single phase generator operation Advanced Power Factor Correction PFC Technology on the input of the UPS makes the input power factor more than 0 98 increasing power efficiency removing harmonic noise and lowers the UPS operational cost e Auto Start on Battery allows the UPS to start in battery mode when utility power is not available e Racl Tower Conversion LCD means that the display be read Rack or Tower configurations by only pressing a button the display electronically rotates to provide the detailed information in an easy to read manner ECO Function can help to save electricity by allowing the UPS to operate in a l
11. an extended period of time it means that there is something wrong with the machine 3 f you need help contact our service department the following messages should be provided for analysis UPS MODEL NO and SERIAL NO e Date of fault happened e Detailed description of the problem include indicator statements from front panel LED Indication and Warning Table LCD Fault Codes Fault causation Fault Code Bus Fault 00 19 Inverter Fault 20 39 Over Heat 40 44 Output short circuit 45 49 Overload 50 54 Output Relay Fault 55 59 Input NTC Fault 60 64 Auxiliary Power Fault 65 69 Input Fuse Fault 70 74 Others 33 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS Line mode Normalvoltase x None _ protection turn to four e on battery mode Normaivotage x X ANN E warning second means x smi voltage bypass X X two minutes Eliminate after starting the UPS mode Main AC high I Once every voltage warning in X our eond bypass mode Main AC low voltage Once every warning in bypass X mode Battery disconnect warning Bypass mode X X Once every Affirm if the battery switch is four seconds closed pi ss Affirm if the battery switch is Inverting mode X X four seconds closed 5 Output overload protection Overload warning in Twice per
12. for more than second to turn on or turn off the UPS e ROTATE BUTTON Press and hold button s for more than 2 seconds to rotate the LCD in any mode e SELF TEST MUTE BUTTON Press and hold button s for more than 1 second in utility mode or ECO mode to operate UPS Self Test Press and hold button s for more than 1 second in battery mode to operate the Mute Function e INQUIRE BUTTON Press and hold the button s for more than second but less than 2 seconds to change inquire function Press and hold this button for more than 2 seconds to change display information e FUNCTION SETTING MODE Press and hold this button for more than second but less than 2 seconds to set options e NON FUNCTION SETTING MODE Press and hold the button for more than 2 seconds 6 Configure the local monitoring software if desired e Insert the UPSilon 2000 CD included with UPS packaging into the CD ROM of the local computer e Select Install program from the Autorun menu and choose for the correct operating system 21 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS Follow the setup instructions Enter the product key when prompted The software key is found on the CD cover Click finish when prompted e UPSILON icon will appear in the system tray of the desktop near the system clock Double click this icon to enlarge the program window e Connect the RS232 cable included the UPS packagin
13. for this type of installation The instructions contained within this safety manual are deemed important and should be closely followed at all times during installation and follow up maintenance of the UPS and batteries CAUTION The unit has a dangerous amount of voltage If the UPS indicator is on the unit s outlets may have a dangerous amount of voltage even when not plugged into the wall outlet because the battery may continue to supply power Care should be taken to undertake installation indoors free from electrically conductive particles which are under temperature and humidity control in order to reduce the risk of electric shock It is best to disconnect the device using the power supply cord Ensure that the equipment is placed in a position near the outlet where easily accessible Except for replacing the batteries all servicing on this equipment must be carried out by qualified service personnel Before conducting any maintenance repair or shipment first ensure that everything is turned off completely and disconnected For additional safety instructions please use the Safety Manual as a reference Special Symbols The following symbols used on the UPS warn you of precautions RISK OF ELECTRIC SHOCK Please observe the warning that a risk of electric shock is present CAUTION REFER TO OPERATOR S MANUAL Refer to the operator s manual for additional information such as important operating and maintenance ins
14. hours for full battery time NOTE If the EBP is going to be out of service or stored for six months or longer the batteries must be recharged for at least 36 hours every six months Extended Battery Pack Q amp A 1 Which EBP s do connect to an AC input source e t is possible to plug in every into an AC input source The more connected the faster the recharge time It is recommended that every third EBP be connected to incoming AC utility to properly charge the batteries in a complete system Leaving too many chargers connected may cause an over charge situation which could damage the batteries 2 Which LED s are supposed to be lit on the front of each EBP 45 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS When an is connected to an AC input source and the unit is charging a GREEN LED on the front of the EBP will be illuminated 3 Are any LED s on the front of the EBP supposed to be lit if it is not connected to an AC input source e No The UPS and or the EBP s that are plugged into an AC input source are responsible for charging the entire system The EBP is still working and has the capability of providing DC voltage when needed No LED on the front bezel will be illuminated 4 The EBP is connected to an AC input source why does the LED on the front of the EBP turn ON and OFF intermittently and does this mean this EBP is not working GREEN LED o
15. inquire about items Items can include input battery output load and temperature The displayed items on LCD screen are showed as following Output Display the output voltage and output frequency of the UPS As the following graphic shows the output voltage is 220v the output frequency is 50Hz Load Display the numerical value of the active power in WATTs and apparent power in VA of the load For example as the following graphics shows the WATT of the load is 100w VA is 100VA Please note that when the load is disconnected it is a normal to see a small numerical value of WATT and VA 27 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS Temperature Display the temperature of the inverter in the UPS The graphics shows the temperature of the inverter is 37 C NES Input Display the voltage and frequency of the input The graphic shows the input voltage is 210v input frequency is 49 8Hz 28 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS Input INIZI Battery Display the voltage and capacity of the battery determined by type The graphic shows the battery voltage is 28v the capacity of battery is 10096 the capacity of battery is an approximation 111 v FA Press and hold the inquiring button for more than 2 seconds LCD begins to display the items seque
16. 007 070707 X 12V 9AH 4 12V 9AH 6 12V 9AH COMMUNICATIONS INTERFACE RS232 USB DRY CONTACT SNMP RS232 USB DRY CONTACT SNMP OPTIONAL INCLUDED WITH UNIT RS232 software cable mounting brackets user s manual input power cord BATTERY 36 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS MODEL NXRTi 1000 NXRTi 2000 NXRTi 3000 UNIT SHIPPING DIMENSIONS W x D x H mm UNIT SHIPPING 26 28 WEIGHT ROI 12 14 5 21 5 24 3 6 28 8 IEC to 1 8m length IEC to 1 8 length IEC to 1 8 length Schuko input plug Schuko input plug Schuko input plug 440 x 380 x 86 5 440 x 520 x 131 440 x 520 x 131 607 x 514 x 170 607 x 654 x 210 607 x 654 x 210 INPUT POWER CORD PHYSICAL 0 75x3C OD6 0mm 1 5x3C OD8 5mm 1 5x3C OD8 5mm RECEPTACLES 6 IEC C13 4 IEC C13 1 IEC C19 UNIT SHIPPING NXRTi EBP1 NXRTi EBP2 NXRTi EBP3 EBP DIMENSIONS 440 x 380 x 86 5 440 x 520 x 131 440 x 520 x 131 W x Dx H mm 607 x 514 x 170 607 x 654 x 210 607 x 654 x 210 UNIT SHIPPING 5 34 41 43 SHIPPING LIST 1 1 UPS 2 1 User s and Installation Manual 3 1 6ft RS232 cable 4 1 UPSILON CD monitoring software 5 2 sets of mounting brackets 6 1 input power cord 37 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS OBTAINING SERVICE If the UPS requires Service 1 Use the TROUBLESHOOTING sec
17. 2X gt lt T REME gt O W c CONVERSION Network Xtreme Rack Tower International Series NXRTi User s amp Installation Manual OE Xtreme Power Conversion XPC Corporation NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS Table of Contents IMPORTANT SAFETY INSTRUCTIONS 4 INTRODUCTIOD seco veR uu INS 6 PRODUCT DESCRIPTION 6 Double Conversion On Line Technology tentent 7 Functions Trees OT ETE 7 SYSTEM CONFIGURATION 9 BE 10 00 2 2 11 40401 13 SNMP Communications Option 14 DETERMINING THE POWER REQUIREMENTS OF YOUR EDUIPMENT SS aou mad vim DM IS 14 HARDWARE INSTALLATION GUIDE 15 EE 15 Storage and Transportat Oi esequi ead hk ayapa Ne Ere 15 16 16 18 INITIAL CONNECTION AND 5 19 USER SOPERATIONS
18. D 9 CAUTION MAX RATED VALUES 12VDC SNMP Communications Option The UPS provides an intelligent slot for internal or external network card This special intelligent network card can be compatible with popular software and hardware found on the web and in operating systems It can support operating systems such as HP Open View IBM Netview SUN Netmanager etc This enables the UPS to provide instant UPS and power information over the network Please contact your reseller for additional details Notes The UPS can be monitored through the RS232 interface or the SNMP card but only one way at a time The user can choose RS232 or SNMP communications through the communications switch on the rear panel of the UPS RS232 is chosen if the switch is depressed to the RS232 position and SNMP is chosen if the switch is depressed to the SNMP position When there are two or more monitored pieces of equipment the ground of each piece of equipment should be shared The SNMP card is configured as DHCP by default IP setting DETERMINING THE POWER REQUIREMENTS OF YOUR EQUIPMENT 1 Make sure the total Volt Amp VA requirements of your connected equipment does not exceed the maximum VA rating for the UPS The maximum VA ratings are shown in the Specifications section of this document 2 Ensure that the equipment plugged into the battery powered outlets does not exceed the UPS rated capacity If UPS rated capacities are
19. MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS EXTERNAL BATTERY SOCKET INPU INPUT BREAKER MAINS POWER HOLE SOCKET RJ45 NET SURGE PROTECTION 11212101 112101 OOOOO0O000 o QODOOO000 LJOODQDODCOOCCOLD LIDODDOCDLCLDLI INTELLIGENT SLOT 5232 OOOO NOOOUOOOO00 ee NOOO NXRTi 2000 3000 REAR VIEW LED Description The UPS has four LED s on the front control panel These LED s allow the user to quickly understand if any action is needed JNPUT BATTERY OUTPUT LOAD 72 E zm e T gt TEMP N Kz C ZND 10 INVERTER LED BATTERY LED BYPASS LED WARNING LED NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS Red LED If this WARNING LED is illuminated it indicates a fault and the UPS will have no output Faults that would indicate this alarm condition include e Overload e Inverter fault e BUS fault e Over temperature fault Yellow LED If this BYPASS LED is illuminated it indicates the user needs to take some action and included UPS Bypass Mode If this BATTERY LED is illuminat
20. O Mode LED indications on front panel on ECO mode are as follows both the inverter green LED and bypass yellow LED are illuminated 30 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS When the input utility equals the input range of the ECO mode and the ECO function is activated the UPS will operate in ECO mode If input AC utility exceeds the range of ECO several times in a row in a minute but stays in the inverter input range the UPS will operate on inverter mode automatically Fault Mode LED indications on front panel in fault mode are as follows Fault mode LCD interface with the fault code display When UPS has a fault the fault LED lights and the buzzer beeps The UPS will turn to fault mode with an overload fault inverter fault and over temperature The UPS cuts off the output and LCD displays the fault codes Pressing the mute key will make the buzzer stop beeping You can also press the ON OFF key to shut down the UPS NOTE As for corresponding information of the fault code please refer to Fault Code information Table The following process must be performed if UPS is connected with generator First turn on generator after it runs stably connect output power of generator to UPS input terminal then turn on UPS After UPS turned on please connect load one by one It is recommended that the generator capacity is twice the UPS rated capacity Do
21. Pack Operation The NXRT UPS System can be connected to multiple extended battery packs to increase the runtime when connected to the UPS supporting the load Most UPS Systems are limited to one or two external battery packs because the UPS is responsible for the recharging and does not have the recharge capacity to handle the additional batteries to a full recharge The NXRT UPS System overcomes this limitation by equipping each extended battery pack EBP with its own charger providing the user a way to achieve 43 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS significantly more battery backup time Not all of the AC input power cords for the EBP s need to be connected to AC the more you connect the faster the recharge of the batteries 1 The DC Circuit Breaker on the rear of the EBP connects and disconnects the DC bus voltage from the EBP to the UPS The DC Circuit Breaker will also trip to the OFF position in the event of an over current condition in the EBP LJL JL JEJE IE EET UAI Dp fergie eee pec OOOO LILJCJL ILE EBP2 REAR VIEW 2 The EBP s use a cable shipped with each EBP to daisy chain together additional EBP s to the first EBP being connected to the UPS in the appropriately labeled connector or for connecting the first EBP to the UPS UPS y EBP 74 4 J 7 a
22. Remove the less important loads line mode second Overload in line Long beeps Remove the less important loads mode protection Overload warning in X X Twice per Remove the less important loads battery mode second Overload in battery Long beeps Remove the less important loads mode protection PIE ul warning in X X Once every 2 Remove the less important loads tie mode seconds Fan fault fan icon Once every 2 Check if the fan is blocked by 7 X X X X flash seconds object If display fault code and X iconA lights contact for maintenance when you can t deal with it by yourself 34 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS Note When UPS has a fault you need to know the working status of UPS and the exact information about the fault promptly by referring to the two tables listed above When the fault occurs firstly perform troubleshooting by referring to the troubleshooting table If the fault still exists please contact the franchiser Fat Cae Solution 000000000 UPS is working in battery mode save disk and close the programs make sure AC mains voltage and frequency is in the normal range line and neutral make a correct connection Check UPS battery connect battery indicator flashes battery disconnected well if battery damaged replace it UPS has no input circuit Keep UPS connecting with mains power Battery not fully charged for more than
23. S The only operations that users are permitted to do are Turning the UPS unit ON or OFF e Operating the user interfaces Connecting data interface cables 22 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS All such operations are to be performed exactly as instructed in this manual The greatest care possible must be taken for any of these operations and any change thereof may prove very hazardous to the operator Turning Off the UPS when connected to an AC source e Once utility power is plugged in the UPS will charge the battery at the moment LCD shows that the output voltage is 0 which means UPS has no output If it is expected to have output of bypass you can set the bps ON by LCD setting menu e Press and hold the ON OFF key for more than half a second to start the UPS then it will start the inverter e started the UPS will perform a self test function LED will light and go out circularly and orderly When self test finishes it will come to line mode the corresponding LED lights UPS is working in line mode Starting the UPS from a DC source cold start e When utility power is disconnected press and hold the ON OFF key for more than second to start UPS The operation of the UPS in cold start is almost the same as that when utility power is available After finishing the self test the corresponding LED lights and UPS are working in battery mode Turnin
24. TM ld a aae QS Ea ex FEY NO 22 Turning Off the UPS when connected to an AC source 23 Starting the UPS from a DC source cold Stat satire tenets concn 23 Turning Off the UPS when in Utility 23 Turning Off the UPS when in Battery Mode tenentes 23 2 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS 21 74 37 311307 23 s 00102 24 uode setia uu 24 SWISS CeO E S OO 25 S nami bP hamaman asas 27 ss 29 MAINTENANC 32 BATTERIES 21 32 REPLACING THE BATTERY sssssssssssseecsescessnessacanvansisavsvaunsansopesensvebuniupeeess 32 TROUBLESHOOTING 2220595 33 LED indication and Warning 33 SPECIFICATIONS 36 SHIPPING CIS Lu 37 OBTAINING SERVIC Escini 38 XTREME POWER CONVERSION XPC CORPORATION LIMITED WARRANTY craniene 39 APPENDIX A EXTENDED BATTERY PACK USER GUIDE 40 Estimated Run Time for UPS with Extended Battery Packs 40 T 43 Extended Battery Pack 1 tette tenente ttti tenete 43 Extended Battery Pack In
25. ackup time the UPS will shut down avoiding battery damage When the input AC voltage returns the UPS will automatically return online to recharge the batteries As shown in fig 1 block diagram An input filter reduces transients on the incoming utility To maintain full battery charge the AC input power is rectified and regulated in the rectifier feeding power to the battery converter and inverter DC power is converted to AC in the inverter passing it on to the load Power is maintained from the battery during a power failure The converter increases voltage appropriately for the inverter Input Filter DC DC Converter Battery Figure 1 Block Diagram Functions and Characteristics Advanced IGBT modules are used in our UPS with electronics that will work for more than 300 000 hours Digital Control Technology with high efficiency algorithm delivers a most reliable controller design used to optimize the output parameters of the UPS The UPS performs a Self Diagnostic Test before starting enabling the UPS to detect and correct any potential problems prior to powering up the load 7 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS e Double Conversion On Line Topology makes the output of the UPS a pure sine wave with consistent frequency and voltage regulation low noise and no interruption in power to the load when utility power is lost e Zero Transfer
26. ass output interface at that moment the letters bPS will flash as following 25 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS Letters flash e Enter the Bypass output setting interface Press and hold the function setting button for more than second but less than 2 seconds at this time the letters bPS will light for an extended period The ON below the bPS will flash Press and hold the inquiring button C DO for more than second but less than 2 seconds to determine whether the bPS function is used or not If used the corresponding word is ON if not the word is OFF Letters flash e Confirm the Bypass output setting interface After selecting ON or OFF press and hold the function setting button for more than 2 seconds The bPS setting function is completed and the ON or OFF below the bPS will light without flash 26 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS e Exit from the setting interface Press and hold function setting button for more than 2 seconds exit from the setting interface and return to the main interface e After setting bPS as ON when utility power is plugged in without turning on the UPS or no utility power is plugged in there is bypass output but no power down backup function Parameter Inquiring Press and hold the inquiring button for more than second but less than 2 seconds to
27. ckaging and never drop the unit Please adhere to the following instructions if the UPS is not installed immediately e Store the equipment as is in its original packing and shipping carton Do not store in temperatures outside the range of 15 C to 25 C e Ensure that the equipment is fully protected from wet or damp areas and from moist air In order to maintain the batteries the UPS should be recharged every 6 months for at least 8 hours If flammable substances such as gases or fumes are present or if the room is airtight a hazardous situation may exist in which no electrical equipment should be operated The instructions in this manual explain how to install the UPS safely Not acknowledging such electrical hazards may be fatal keep this manual for future reference WARNING It is strongly recommended that the UPS cabinet not be opened as components have very high voltage and touching those components may be fatal Only a qualified technician or authorized agent may service the unit The UPS unit s output receptacles carry live voltage even when not connected to an input voltage source The UPS has its own internal energy source 15 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS Environment Ensure that all environmental concerns and requirements are met according to specifications listed in this document otherwise the safety of installation personnel cannot b
28. e guaranteed and the unit may malfunction Ensure that you remember the following when locating the UPS system and battery options e Avoid extremes of temperature and humidity Maximum battery life can be attained with recommended temperature range of 15 C to 25 e Provide protection for the equipment from moisture e Space and ventilation requirements must be met Ensure there is 100mm behind and 50mm on the sides of the UPS for proper ventilation e Ensure that the front of the UPS remains clear for user operation Installation Plastic Base Installation for use in Tower configuration Two plastic base brackets interconnect and flatten for holding 2U base unit configuration Plastic base bracket Plastic base bracket Plastic base bracket Plastic base bracket 16 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS The same plastic base assembly plus a 1U plastic base extension bracket are connected together as shown below to accommodate 3U enclosures 1U plastic base bracket Plastic base bracket extended board 1U plastic base bracket Plastic base bracket extended board 1U plastic base bracket extended board Plastic base bracket Plastic base bracket Plastic base 1U plastic base bracket Plastic base bracket extended board bracket 17 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS 19 Cabinet Ear In
29. ed it indicates the user needs to take some action and included e UPS operating on battery e Batteries Overcharged e Charger fault e Fan fault e Batteries discharged to low voltage level Green LED If this INVERTER LED is illuminated it indicates that everything is normal and the UPS is being powered by incoming AC utility or by the batteries After starting the UPS the four LED s will light and go out one by one cycling until the UPS starts successfully LCD Descriptions The LCD display electronically rotatable by PRESS and HOLD the ROTATE button for more than 1 second ON OFF ROTATE SYSTEM TEST MUTE NXRTi BUTTONS 11 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS 111 VBA Fan status c graphics Eu Numerical Section C I M value Charger status ENS graphics Capacity section graphics section Capacity graphics Charger status section graphics section Numerical Fan status value graphics section section NXRTi LCD PANEL IN RACK MODE The LCD display contains Numerical value section This section displays the corresponding numerical value of output load temperature input and battery Example Output Voltage 220V Output Frequency 50Hz Capacity graphics section This section displays the capacity of the battery and amount of load on the UPS output Each pane represents 20 capacity When the capacity of the battery is 80 100 5
30. exceeded an overload condition may occur and cause the UPS to shut down and trip the circuit breaker 3 If the power requirements of your equipment are listed in values other than Volt Amps VA convert Watts W or Amps A into VA by doing the calculations below Note The equation below only calculates the maximum amount of VA that the equipment can use not what is typically used by the equipment at any given time Users should expect usage requirements to be approximately 6096 of the value to estimate power requirements Watts W x 1 43 VA or Amps A x 230 Volts V VA 14 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS Add the totals for all of the equipment and multiply this total by 0 65 to calculate actual power requirements Note Many factors can affect the amount of power that your computer system will require The total load that you will be placing on the battery powered outlets should not exceed 8596 of the UPS capacity HARDWARE INSTALLATION GUIDE Inspect the UPS upon receipt The packaging is recyclable keep it for reuse or dispose of properly Safety Information Information presented here is vital to all personnel Please read all Safety information Storage and Transportation Please handle the UPS and associated equipment with extreme caution since a high amount of energy is contained in the batteries Always keep the unit in an upright position as marked on the pa
31. g to the Computer and UPS Communication should start momentarily If it does not click on Settings up on the UPSilon toolbar then select a different Comport until communication is established e Click on Manual in the UPSILON toolbar for further software configuration e NOTE PLEASE VERIFY AUTOMATIC SHUTDOWN TIME PARAMETERS IN THE SETTINGS SECTION FOR YOUR SPECIFIC INSTALLATION 7 Configure the optional NetAgentll SNMP card if installed e Insert the NetAgent Utility CD included with SNMP packaging into a PC and download the user manual Install Netility from the AutoRun menu Connect a network cable from the PC to the SNMP Run Netility program and it will auto search and list available NetAgents SNMP card Highlight and click Configure to change the network settings on the NetAgent discovered Disconnect the cable to the PC and connect the SNMP card to your network e Access the SNMP card via the network and make configuration changes using the manual downloaded previously e NOTE PLEASE VERIFY AUTOMATIC SHUTDOWN TIME PARAMETERS IN THE SETTINGS SECTION FOR YOUR SPECIFIC INSTALLATION 8 After charging is complete connect the loads to the UPS while monitoring the load levels via the UPS LCD or via the software Do not connect any devices that have the possibility of overloading the UPS Refer to the Troubleshooting section and or Technical Support with any problems during setup USER S OPERATION
32. g Off the UPS when in Utility Mode e Press and hold the ON OFF key for more than second to turn off the UPS and inverter e After the UPS shuts down the LEDs go out and there is no output If output is needed you can set bps ON by LCD setting menu Turning Off the UPS when in Battery Mode e Press and hold the ON OFF key for more than second to turn off the UPS When turning off the UPS it will do a self test first then the LED light and LCD display will turn off Self Test amp Mute Test Operation When the UPS is in on line mode Press and Hold the Self Test Mute Button for more than 1 second the LED lights and go out in order The UPS arrives then at its Self Test Mode and tests its status The UPS will exit this mode automatically after finishing testing LED resumes status e When the UPS is in Battery Mode Press and Hold the Self Test Mute Button for more than 1 second the buzzer stops Press and Hold the Self Test Mute Button for more than 1 second and the UPS will restart buzzer again 23 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS Parameter Setting e The UPS has a setting function It can run the setting function in any mode After setting the changes will become effective at once when The set information can be saved only when the battery is connected and following normal power off process The operation of settings are as following ECO mode setting
33. ine interactive mode The load is supplied with utility power directly while the inverter is in a standby mode until needed 8 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS SYSTEM CONFIGURATION The UPS device and the internal batteries make up the system Depending on the site and load requirements of the installation certain additional options are available for the solution Planning a UPS system the following should be taken into consideration e total demand of the protected system shall dictate the output power rating VA Allow margin for future expansion or calculation inaccuracies from measured power requirements Backup time required will indicate the battery size needed If the load is less than the UPS nominal power rating then actual backup time is longer e following options are available o Extended Battery Packs NXRTi EBP1 for 1000 NXRTi EBP2 for 2000 NXRTi EBP3 for 3000 o Connectivity Options SNMP WEB card o Xtreme Power Distribution Units XPDU See the Specification section of this manual for additional model information gt T Exe LL rt cone 4 NXRTi series FRONT VIEW EXTERNAL GND RJ45 NET BATTERY INPUT SCREW SURGE SOCKET BREAKER HOLE OUTPUT PROTECTION 89232 INPUT MAINS INTELLIGENT SLOT POWER SOCKET NXRTi 1000 REAR VIEW 9 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S
34. n the front of each indicates that the charger contained in the is charging Under certain conditions when the batteries are 10096 charged the charger in the EBP will shut off and the LED will no longer be illuminated This is normal operation for the EBP The EBP is working properly 5 Why don t the LED s on each EBP connected to an AC input source turn ON and OFF at the same time e The charger on each functions independently from the others One charger may be charging while another one might be at 10096 and the charger turned off This is normal operation of the EBP CAUTION It is very critical to connect the correct voltage EBP with the UPS intended EBP1 is for NXRTi 1000 EBP2 is for NXRTi 2000 EBP3 is for NXRTi 3000 CONNECTING THE INCORRECT BATTERY PACK TO THE UPS MAY RESULT IN DAMAGE TO THE UPS AND OR BATTERY PACK WILL VOID THE WARRANTY All EBP s have a different DC voltage configuration intended only for the UPS s listed above PLEASE DO NOT MIX EBP s AND MAKE SURE YOU ONLY CONNECT THE EBP TO LIKE EBP s OR UPS INDICATED ABOVE DC VOLTAGES ARE MARKED ON BOTH THE UPS AND THE EBP MAKE SURE THEY MATCH 46 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS CAUTION LABEL ON EBP CABLE CONNECTORS PLEASE CHECK VOLTAGES CAREFULLY 47 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS 48
35. nt from the customer in a timely manner as agreed to with the customer once the customer has requested and received a Return Material Authorization RMA number DOA equipment is defined as equipment that does not properly function according to user documentation when initially received and connected in conjunction with proper procedures as shown in the user documentation or via support provided by XPC Corporation personnel or authorized agents This warranty shall be void if a the equipment is repaired or modified by anyone other than XPC Corporation or a XPC Corporation approved third party b the equipment is damaged by the customer is improperly used or stored is subjected to an adverse operating environment or is operated outside the limits of its electrical specifications or c the equipment has been used or stored in a manner contrary to the equipment s operating manual intended use or other written instructions Any technical advice furnished by XPC Corporation or a XPC Corporation authorized representative before or after delivery with regard to the use or application of Xtreme Power Conversion equipment is furnished on the basis that it represents XPC Corporations best judgment under the situation and circumstances but it is used at the recipient s sole risk EXCEPT AS STATED ABOVE XPC Corporation DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE EXCEPT AS
36. ntially every 2 seconds Press and hold the button again and the display will return to output status Run Mode Bypass Mode LED indications on front panel in bypass mode are as following 29 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS Bypass yellow LED is on the buzzer beeps once every 2 minutes The warning red LED is on when beeping LCD displays are according to the exact load and battery capacity Turn to bypass mode under the following two conditions e Turn off the UPS in line mode while starting the bypass output e Overload in line mode NOTE When UPS is working in bypass mode it has no back up function Line Mode LED indications on the front panel in line mode are as following the inverter green LED is on When input AC utility is in line with the working conditions UPS will work in line mode Battery Mode LED indications on front panel in battery mode are as follows both the inverter green LED and battery yellow LED are on the buzzer beeps once every 4 seconds The warning red LED is on when beeping When the utility power is not available or is not stable UPS will turn to battery mode immediately Continuously working on battery mode can last for 20 hours depending on the battery volume and the load If battery discharge for 20 hours and the load is lower than 1096 of rated power the UPS will alarm for hour and then shutdown to protect the batteries EC
37. panes would be displayed When the load reaches 40 6096 3 panes would be displayed When the UPS is in overload the icon will flash When the capacity of battery is too low or disconnected the icon will also flash 12 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS Fan status graphics section This section displays if the fan works normally When the fan is working normally it will show the dynamic fan blades rotating If the fan fails or works abnormally the icon will keep flashing and alarm Charger status graphics section The section displays the status of the charger When the charger is working normally the corresponding icon will vary dynamically and orderly When the charger works abnormally the icon will flash as shown below Flash When the UPS is in Battery Mode the number of icons for the charger status section will vary according to the changeable capacity of the battery For example there are five panes in the figure below so the corresponding number of icons is five rows RS 232 Standard Interface The RS 232 interface uses a 9 pin female D sub connector Information provided includes data about utility load and the UPS The interface port pins and their functions are identified in the following table 800800 13 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS PIN FUNCTIONS 1 4 6 7 8 NOT USE
38. receipt and a brief description of the problem Mark the RMA number on the outside of all packages Xtreme Power cannot accept any package without the RMA number marked on the outside of the boxes Return the UPS by insured prepaid carrier to the address provided by the Technician Refer to the Warranty statements in this manual for additional details on what is covered 38 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS XTREME POWER CONVERSION XPC CORPORATION LIMITED WARRANTY Xtreme Power Conversion XPC Corporation warrants Xtreme Power Conversion equipment when properly applied and operated within specified conditions against faulty materials or workmanship excluding batteries for a period of two years for NXRTi Series products from the date of purchase XPC Corporation warrants internal batteries for a period of two years from the date of purchase For equipment sites within the United States and Canada this warranty covers repair or replacement at the sole discretion of XPC Corporation The customer is responsible for the costs of shipping the defective product to XPC Corporation XPC Corporation will pay for ground shipment of the repaired or replacement product This warranty applies only to the original purchaser If equipment provided by XPC Corporation is found to be Dead on Arrival DOA XPC Corporation will be responsible for the costs of shipping product to and returning equipme
39. s only 12VDC and 24VDC the battery can present a high risk of short circuit current and electrical shock The short circuit current capability of the battery is sufficient to burn wire or tools very rapidly producing molten metal Observe these precautions when replacing the battery 1 Remove all watches rings or other metal objects Only use tools with insulated handles Do not lay tools or metal parts on top of battery or any terminals Wear protective eye wear goggles rubber gloves and boots Disconnect the charging source before connecting or disconnecting the battery terminals DA ae ie Determine if the battery is inadvertently grounded If inadvertently grounded remove the source of the ground Contact with a grounded battery can result in electrical shock The likelihood of such shock will be reduced if such grounds are removed during installation and maintenance applicable to a UPS and a remote battery supply not having a grounded circuit 32 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS TROUBLESHOOTING The following messages are the information that users would find on UPS if it fails to perform as designed Users can judge if the fault is caused by external factors and know how to deal with it by making full use of the information 1 Fault indicator on indicates that the UPS has detected some fault 2 Buzzer beeps indicates that UPS needs maintenance if beeps for
40. side Refer servicing to qualified service personnel CAUTION Non isolated Battery supply Risk of electric shock battery circuit is not isolated from AC input hazardous voltage may exist between battery terminals and ground Test before touching WARNING Fuses To reduce the risk of fire replace only with the same type and size of fuse WARNING unit intended for installation in a controlled environment CAUTION po not dispose of batteries in a fire the battery may explode CAUTION po not open or mutilate the battery released electrolyte is harmful to the skin and eyes CAUTION A battery can present a risk of electric shock and high short circuit current The following precaution should be observed when working on batteries Remove watches rings or other metal objects e Use tools with insulated handles To reduce the risk of electric shock disconnect the UPS from the main supply before installing a computer interface signal cable Reconnect the power cord only after signaling interconnections have been made 4 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS Servicing of batteries should be performed or supervised by personnel with knowledge of batteries and the required precautions Keep unauthorized personnel away from batteries These UPS units are extremely heavy Do not install the UPS in a rack or enclosure by its front two ears only Adjustable rack rails are required
41. stallation 45 Extended Battery Pack Q amp A ptite 45 Thank you for selecting this uninterruptible power supply UPS It provides you with protection for connected equipment Please read this manual before installing the NXRTi Series UPS models NXRTi 1000 NXRTi 2000 and NXRTi 3000 as it provides important information that should be followed during 3 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS installation and maintenance of the UPS and batteries allowing you to correctly set up your system for the maximum safety and performance Included is information on customer support and service if it is required If you experience a problem with the UPS please refer to the Troubleshooting section in this manual to correct the problem If the problem is not corrected please collect information so that the Technical Support personnel can more effectively assist you WARNING Any changes or modifications not expressly approved by the manufacturer of this device could void the user s authority to operate the equipment IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS CAUTION UPS having Internal Batteries Risk of electrical shock Hazardous live parts inside this unit are energized from the battery supply even when the input AC power is disconnected CAUTION No User serviceable Parts Risk of electrical shock do not remove cover No user serviceable parts in
42. stallation The bracket is installed on the UPS as shown below screw B UPS FRONT CORNER UPS RACK BRACKET UPS FRONT CORNER WITH BRACKET INSTALLED 18 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS Plastic base 01184110 1 1 1 TOWER ASSEMBLED UNIT T n ood Cabinet installation bracket UPS gt Cabinet OOO RACK ASSEMBLED UNIT INITIAL CONNECTION AND STARTUP Ensure that the UPS and optional battery packs are mounted correctly and the UPS is disconnected from input power before proceeding 1 Connect external battery packs option 19 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS 2 3 4 5 CAUTION CONNECT ONLY BATTERY PACKS PROVIDING THE SAME DC VOLTAGE AS THE UPS PLEASE DOUBLE CHECK LABELING ON THE UPS AND BATTERY PACKS TO ASSURE PROPER VOLTAGES ARE CONNECTED CONNECTING THE INCORECT BATTERY PACK TO THE UPS MAY RESULT IN DAMAGE TO THE UPS AND OR BATTERY PACK THAT WILL VOID THE WARRANTY Ensure that the UPS is disconnected from AC input and is off while connecting the External Battery Packs Ensure all battery breakers are in the OFF position Remove the EBP covers on the UPS and EBP Connect the battery cable that comes with the External Battery Pack between the External Battery Pack to the UPS Secure the
43. tion in this manual to eliminate obvious causes 2 Verify there are no circuit breakers tripped 3 Call your dealer for assistance If you cannot reach your dealer or if they cannot resolve the problem contact Xtreme Power Conversion Corp Technical Support at 1 720 292 1217 or support xpcc com Please email the following information to the Technical Support Department 560 deo Dem Your name and address The serial number of the unit Where and when the unit was purchased All of the model information about your UPS Any information on the failure including LED s that may or may not be illuminated A description of the protected equipment including model numbers if possible A technician will ask you for the above information and if possible help solve your problem over the phone In the event that the unit requires factory service the technician will issue you a Return Material Authorization number RMA If you are returning the UPS to Xtreme Power for service please follow these procedures 1 4 Pack the UPS in its original packaging If the original packaging is no longer available as the Technical Support Technician about obtaining a replacement set of packaging material It is important to pack the UPS properly in order to avoid damage in transit Never use Styrofoam beads for a packing material Include a letter with your name address daytime phone number RMA number a copy of your original sales
44. tructions SAFE GROUNDING TERMINAL Indicates primary safe ground LOAD ON OFF Pressing the button turns on off the output receptacles and the indicator light RJA5 RECEPTACLE The receptacle provides network interface connections and telephone or telecommunications equipment should not be plugged into it Please do not discard of the UPS or the UPS batteries as the UPS may have valve regulated lead acid batteries Please recycle batteries appropriately 5 NXRTi 1000 NXRTi 2000 NXRTi 3000 USER S MANUAL UNINTERRUPTIBLE POWER SUPPLY UPS EMC standard Safety standard Our products are manufactured in accordance with the following EMC international grade standards and has passed the CE authentication EMC standard number Safety standard number IEC62040 2 IEC62040 1 IEC61000 4 2 GB4943 2005 INTRODUCTION The information provided in this manual covers high voltage single phase 1000 3000 VA uninterruptible power systems their basic functions operating procedures options available and emergency situations It also includes information on how to ship store handle and install the equipment Only detailed requirements of the UPS units are described herein and installation must be carried out in accordance with this manual Electrical installation must also carefully follow local legislation and regulations Only qualified personnel should conduct these installations as failure to acknowledge electrical hazards could
Download Pdf Manuals
Related Search