Performer 18 HEX
Contents
1. Sh Performer 18 HEX 18 x 12W 6 in 1 colour LEDs RGBWAUV User Manual Order code LEDJ252B Safety advice WARNING FOR YOUR OWN SAFETY PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START UP e Before your initial start up please make sure that there is no damage caused during transportation e Should there be any damage consult your dealer and do not use the equipment e To maintain the equipment in good working condition and to ensure safe operation it is necessary for the user to follow the safety instructions and warning notes written in this manual e Please note that damages caused by user modifications to this equipment are not subject to warranty CAUTION CAUTION TAKE CARE USING KEEP THIS EQUIPMENT THIS EQUIPMENT AWAY FROM RAIN MOISTURE AND LIQUIDS HIGH VOLTAGE RISK OF ELECTRIC SHOCKH IMPORTANT The manufacturer will not accept liability for any resulting damages caused by the non observance of this manual or any unauthorised modification to the equipment e Never let the power cable come into contact with other If the equipment is dropped or damaged disconnect the cables Handle the power cable and all mains voltage mains power supply immediately and have a qualified connections with particular caution engineer inspect the equipment before operating again e Never remove warning or informative labels from the unit If the equipment has been exposed to drastic Do not open t2. e of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product should not be mixed with other commercial wastes for disposal CE fe www prolight co uk Performer 18 HEX User Manual s8
3. he equipment and do not modify the unit temperature fluctuation e g after transportation do not connect power or switch it on immediately The arising condensation might damage the equipment Leave the equipment switched off until it has reached room temperature e Do not connect this equipment to a dimmer pack e Do not switch the equipment on and off in short intervals as this will reduce the system s life e Only use the equipment indoors If your product fails to function correctly stop use e Do not expose to flammable sources liquids or gases immediately Pack the unit securely preferably in the e Always disconnect the power from the mains when original packing material and return it to your Pro Light equipment is not in use or before cleaning Only handle dealer for service the power cable by the plug Never pull out the plug by pulling the power cable Repairs servicing and power connection must only be e Make sure that the available voltage is between carried out by a qualified technician THIS UNIT CONTAINS 100 240V 50 60Hz NO USER SERVICEABLE PARTS e Make sure that the power cable is never crimped or WARRANTY One year from date of purchase damaged Check the equipment and the power cable periodically Only use fuses of same type and rating OPERATING DETERMINATIONS If this equipment is operated in any other way than those described in this manual the product may suffer damage and the warranty become
4. isplay shows LL on the LED display Press ENTER to confirm the setting Use the UP and DOWN buttons to ajust the speed between CCOO 0949 Press the ENTER button to confirm the setting To exit out of any of the above options press the MENU button Colour fade mode To access colour fade mode press MENU until the display shows L F on the LED display Press ENTER to confirm the setting Use the UP and DOWN buttons to ajust the speed between LPUG CF99 Press the ENTER button to confirm the setting To exit out of any of the above options press the MENU button www prolight co uk Performer 18 HEX User Manual 4 Operating instructions Auto mode To access auto mode press MENU until the display shows dE on the LED display Press ENTER to confirm the setting Use the UP and DOWN buttons to ajust the speed between dE OG dEYY Press the ENTER button to confirm the setting To exit out of any of the above options press the MENU button Static colour mode To access the static colour mode press MENU until 2c5 shows on the LED display Now use the UP and DOWN buttons to select the brightness between r JUG r 255 Press the ENTER button and repeat for green L blue 4 white u amber 4 and UV FP Value 000 255 000 low brightness 255 high brightness To exit out of any of the abo
5. last fixture the possibilities of erratic behaviour 3 pin Order ref CABL9O 5 pin Order ref CABL89 5 pin XLR DMX connectors Some manufactures use 5 pin XLR connectors for data transmission in place of 3 pin 5 pin XLR fixtures may be implemented in a 3 pin XLR DMX line When inserting standard 5 pin XLR connectors in to a 3 pin line a cable adaptor must be used The diagram below details the correct cable conversion F B A E 5 pin XLR socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal Pin 4 N C Pin 5 N C 3 pin XLR socket Pin 1 GND screen Pin 2 Signal Pin 3 Signal 5 pin XLR socket 3 pin XLR socket Pin 1 GND screen Pin 1 GND screen 8 Pin 2 Signal Pin 2 Signal Pin 3 Signal Pin 3 Signal Pin 4 N C Pin 5 N C www prolight co uk Performer 18 HEX User Manual 7 WEEE notice Correct Disposal of this Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries Si with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed of with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reus
6. ments for DMX operation This fixture can be controlled via DMX 512 protocol The DMX address is set on the back of the unit Your unit and your DMX controller require a standard 3 pin XLR connector for data input output see image below Further DMX cables can be purchased from all good sound and lighting suppliers or Pro Light Concepts dealers Please quote CABL10 2m CABL11 5m CABL12 10m Also remember that DMX cable must be daisy chained and cannot be split www prolight co uk Performer 18 HEX User Manual 6 DMX setup Notice Be sure to follow the diagrams below when making your own cables Do not connect the cables shield conductor to the ground lug or allow the shield conductor to come in contact with the XLRs outer casing Grounding the shield could cause a short circuit and erratic behaviour common DMX 512 out DMX 512 in 3 pin XLR 3 pin XLR EN MORE EN RNR SORES OM EE OE XLR MALE SOCKET XLR FEMALE SOCKET XLR Pin Configuration 2 cold 1 ground 1 ground 2 cold Pin 1 Ground Q Pin 2 Negative 3Hot 3Hot Pin 3 Postive Special note Line termination When longer runs of cable are used Termination reduces signal transmission you may need to use a terminator on problems and interferance it is always the last unit to avoid erratic behaviour advisable to connect a DMX terminal _ resistance 120 Ohm 1 4 W between pin 2 Using a cable terminator will decrease DMX and pin 3 DMX of the
7. mple a fixture that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 100 would read data from channels 100 101 102 103 104 105 and 106 Choose a start address so that the channels used do not overlap E g the next unit in the chain starts at 107 DMX 512 DMX Digital Multiplex is a universal protocol used as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions form the controller to the fixture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a data out terminal DMX linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant To ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned to a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain DATA cable DMX cable require
8. s void Incorrect operation may lead to danger e g short circuit burns and electric shocks etc Do not endanger your own safety and the safety of others Incorrect installation or use can cause serious damage to people and or property www prolight co uk Performer 18 HEX User Manual 2 Product overview amp technical specifications Performer 18 HEX The Alu Performer Par HEX punches out astonishing levels of colour ideal for uplighting in large venues general stage wash and illumination Featuring 18 x 12W 6 in 1 LEDs the Performer HEX offers shadow free light output across a wide colour spectrum e 18 x 12W 6 in 1 colour LEDs RGBWAUV e Beam angle 40 e DMX channels 6 or 10 selectable e Static colour colour change colour fade auto run sound e Bracket allows for multiple rigging and floor standing applications e 4 push button menu with LED display e Captive power connection e 3 pin XLR in out sockets active and master slave modes ss Fan cooled e O 100 dimming with variable strobe 40 Lux 29625 6920 3010 1635 981 n u a a C A O Om 1m 2m 3m 4m 5m DMX OUT 100 240V 50 60Hz FUSE F2A 250V O MENU 01 Earth point 02 LED display 03 Function buttons 04 DMX input socket 05 DMX output socket 06 Captive power connection O7 Fuse F2A 250V www prolight co uk PERFORMER 18 HEX Cr UP DOWN ENTER www prollght co uk In the box 1 x fix
9. ture amp 1x user manual Performer 18 HEX 290mm Specifications Power consumption Performer 18 HEX 190W Power supply 100 240V 50 60Hz Fuse F2A 250V Dimensions 290 x 270 x 255mm Weight 2 6kg Order code LEDJ252B 270mm User Manual 3 Operating instructions DMX mode To select the DMX address press the MENU button on the rear of the unit to show dU onthe LED display Now press the ENTER button and use the UP and DOWN buttons to select the DMX address between 000 512 To exit out of any of the above options press the MENU button DMX channel mode Operating in a DMX control mode environment gives the user the greatest flexibility when it comes to customising or creating a show In this mode you will be able to control each individual trait of the fixture and each fixture independently To access the DMX channel mode press the MENU button on the rear of the unit to show amp LH or IOCH on the LED display Now press the ENTER button and use the UP and DOWN buttons to select between 6 and 10 channel To exit out of any of the above options press the MENU button 6 channel mode 10 channel mode Channel value Function 3 000 255 Amber 0 100 000 255 UV 0 100 e fe oo0255 ercon 0100 a oo0o2s5 wnte 0100 o oo0255 amber 0100 Colour change mode To access colour change mode press MENU until the d
10. ve options press the MENU button Master slave mode To set the master unit press the MENU button on the rear of the master unit to select your desired program sound active auto static colour or colour fade To set the other units in slave mode press the MENU button on the rear of the unit to show dig on the LED display and press the ENTER button to confirm the setting The units will now run in sequence with the master unit To exit out of any of the above options press the MENU button Please ensure that all slave units are set to the same DMX channel mode as the master unit Sound active mode To access the sound active mode press the MODE button on the rear of the unit to show hE bE on the LED display The unit will now respond to sound To exit out of any of the above options press the MODE button Menu system Static colour mode ag og og og og og Colour change mode Colour fade mode CPGG CP99 dEO0 dEIS Sound active mode bEbE DMX mode 6CH 10CH Address setting OG in dS ie N u N u N u N u N u N u m u m u www prolight co uk Performer 18 HEX User Manual 5 DMX setup Setting the DMX address The DMX mode enables the use of a universal DMX controller Each fixture requires a start address from 1 512 A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address For exa
Download Pdf Manuals
Related Search