PIR USER MANUAL - SPRINKLER TALK
Contents
1. y Home amp Landscape Controls MotionControl USER MANUAL WIRELESS MOTION SENSOR Quick easy installation with no wires required Once motion is detected a signal is sent to an ABT ZoneControl receiver The signal turns on any landscape lights connected to the ZoneControl Unit Any lights not already On will turn on for 5 minutes INSTALLATION OVERVIEW 1 Take the PIR over to the ZoneControl you want it learned into 2 Learn the PIR into the ZoneControl 3 Test the unit to make sure it operates correctly at the desired location 4 Mount the MotionControl unit in the desired location Height of 7 5 1s recommended 5 Adjust the angle if necessary left right up down 6 If desired change the duration on the MotionControl from 5 60 minutes with the Programmer LEARNING THE MOTIONCONTROL TO A ZONECONTROL 1 With the MotionControl in hand move to the desired ZoneControl Receiver Place the supplied magnet over the arrow on the left side of the MotionControl 2 Remove the magnet when you see a red light on the front screen 3 Using a magnet swipe the ZoneControl Reed 1 top Reed The ZoneControl will start to click until it receives a signal from the MotionControl Swipe your hand in front of the MotionControl to send a signal Once the signal is received the ZoneControl will stop clicking 4 Once complete mount the MotionControl in the desired location and see if the lights connected to the ZoneCon2. Do not release the OK button until you hear the loud beep gt Send Time Datea Motion Astro v Screw MOUNTING 1 Optimal mounting height is 7 5 Ft Attach the MotionControl to the A mounting arm with a screw A Screw the B mounting bracket into the wall using the 2 wall mount screws Place the MotionControl on the mounting bracket and screw in the top screw To tilt the MotionControl simple loosen the screw adjust the unit 1 or 2 clicks and re tighten FAQ s and HINTS Question Answer My MotionControl unit does not turn the lights on Make sure the unit is properly learned into the respective Zone Control Receiver Make sure that there are not any large metal objects or steel Reinforced concrete walls between the MotionControl and the Zone Control My MotionControl unit senses all movement in the Make sure the unit is properly mounted Tilting the MotionControl down area including my pets will pick up more movement including animals What can cause objects to trigger the MotionControl Positioning the MotionControl into direct sun light Close proximity to a heating or cooling A C duct Vegetation that moves in front of a heated source How should I mount the MotionControl to get the most Mount the MotionControl 7 5 high facing the area effective use of it to be protected and make sure that there are no obstacles such as walls furniture posts counter etc that are interfering with the
3. beam pattern Also check to make sure that there is no source of heat or cold to interfere with the MotionControl function If I have a long wall and need to install multiple Mounting them between 3 and 4 meters 10 and 13 apart MotionControl units then how far apart should I mount them insures that you get good beam coverage of the area How many MotionControl units can I learn into a Zone Control Each MotionControl unit acts like a transmitter Each ZoneControl can Learn 8 separate transmitters Why won t my MotionControl shut off after 5 minutes Did you change the duration from 5 to 10 60 minutes If the MotionControl senses movement after 4 minutes it will stay on for another 5 minutes If the duration has been changed to a longer time the MotionControl will stay on for that additional timeframe Specifications Power source use CR123A 3V Panasonic lithium battery only Dimensions L x W x H 3 5 x 3 5 x 3 5 Weight 5 5 oz with battery and bracket Typical battery life 5 to 8 years Operating temperature 32 to 120 F 0 to 49 C Operating frequency 433 MHz Maximum horizontal sensing angle 110 Maximum detection range 40 Technical support Toll free 888 869 4737 in the US including Alaska and Hawaii Puerto Rico Canada Outside the toll free area Contact your local dealer FCC compliance This device complies with part 15 of the FCC rules Operation is subject to the following conditions 1 This de
4. fig 3 fig 1 Side View fig 2 Distance Ft Distance Ft TOP VIEW w EX 18 degrees Distance feet Distance Ft 25 Distance feet Distance feet CHANGING THE DURATION OF THE MOTIONCONTROL To change the duration on the MotionControl utilize the programmer v2 0 or later The MotionControl comes with a 5 minute setting on the sensor duration Utilize the following instructions to change the desired duration Follow the steps below to change the Motion Sensor time duration Time can be changed to 10 15 20 25 30 45 or 60 minutes DURATION 1 Scroll down to the 2 Press ok key 3 Press K or STEPS to change the time gt Motion Controla gt E duration Setting bed Night Only 4 Press key to gt V10 Minutes confirm ee You can change the Setting from Night Only to Day amp Night if Night Day desired STEPS 1 Scroll down to the 2 Press ok key 3 Press to move down to the Night PMotion Controla i a Hiu ntr 5 ienie only line Dane Night Only 4 Press orka 5 Press 0K key to to change to Day amp confirm Night 5 Minutes 10 Minutes Day amp Night Night Only TRANSMIT You can now send the Motion Sensor Time and Day Night Data STEPS To transmit the data to the ZoneControl make sure you swipe reed 1 1 Swipe reed 1 ZoneControl will start to click 2 Within about 2 ft away set the wireless programmer to Send time date and hit OK
5. trol turn on correctly Note After the initial min test there is a 4 minute delay until the MotionControl will sense movement WALK TEST 1 Place the supplied magnet over the arrow on the left side of the MotionControl and Remove the magnet when you see a red light on the front screen 2 Move in the area you want covered by the MotionControl As you walk the LED on the MotionControl will flash This will continue for 1 MINUTE to allow you to check the coverage of the motion sensing beam Note There is a 3 SECOND delay between red light flashes DAY NIGHT MODE The MotionControl has a Day Night feature built in The MotionControl comes programmed to only trigger at night Between 8 00 a m and 3 00 p m the MotionControl will not turn lights on This feature can be changed with the programmer if a customer wants to have the MotionControl trigger during the day and night TESTING NOTE You can test the product 3 times before it reverts to night mode only This is important to note that after you test 3 times the MotionControl will revert to night time only mode SENSOR COVERAGE PATTERNS The Charts demonstrate how the beam pattern changes as you tilt the angle of the MotionControl All units are in feet 0 is the MotionControl facing straight outwards with no tilt fig1 9 is the MotionControl tilted down one click fig 4 18 is the MotionControl tilted down 2 clicks fig 2 9 is the MotionControl tilted up one click
6. vice may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment
Download Pdf Manuals
Related Search