Steps Manual - Backyard Ocean
Contents
1. FOR IN GROUND 7400800 STEP ONLY 1 Place the back trim over the 2 Repeat procedure to install the 3 Using a hack saw cut 14 off lower back panel and align the tabs back trim extension and the side trim from the bottom ends of two posts with the slots on panel and push Insert cut posts into both holes down until seated located on the second step and push down until posts stop A little liquid soap on the posts will make assembly easier 4 Insert the other posts into the two 5 Slide a deck connector over 6 Rotate posts to align the flat side holes on third tread and push down each of the top posts again liquid with the flat side on the handrail and until post stops Using the two plugs soap on the posts will make install both handrails by tapping down from hardware bag plug the two this easier with a rubber mallet unused holes on the bottom tread Ill AUAM 7 Attach the handrail to each post 8 Attach all four posts to the step using one 10 x 1 1 4 self tapping panels using one 10 x 1 1 4 self screw repeat for the second hand rail tapping screw in each post Tools needed Parts needed STEP 4 cordless drill with Phillips driver rubber mallet flexible fourth riser fourth tread upper side panel upper back panel 4 handrail posts 2 handrails 2 deck connectors and 10 10 x 1 1 4 self tapping screws FOR ABOVE GROUND 400700 STEP ONLY 1 Insert the two tabs on the upper sid2. 11 Install one of the round step pads over the round tab located on the bottom of the stringer assembly A little liquid soap on the round tab will make assembly easier 14 Align the tab on the side stringer with the groove on the stringer and push down until seated Tools needed cordless drill with Phillips driver rubber mallet Parts needed left bottom tread center bottom tread right bottom tread flexible STEP 2 bottom riser second tread flexible second riser third tread flexible third riser back ballast side ballast and 4 white plugs FOR ABOVE AND IN GROUND STEPS 7oLes sann REQUIRED required for Step 2 1 Position the left bottom tread over 2 Next position the right bottom 43 Lay the center bottom tread over the side extension panel and over the tread over the back extension and the right and left bottom treads and raised tab on the stringer Push down over the raised tab on the side push down and inward The center and inward until seated Attach the stringer Push down and inward until tread will attach from underneath the tread to the stringer using one of the seated Attach the tread to the side step Lean the assembly back to 10 x 1 1 4 self tapping screws in the stringer using one 10 x 1 1 4 self expose the bottom of the tread outer hole tapping screw tapping screws 4 Attach the center tread using two 5 With the step assembly still 46 The flexible riser will only be 10 x
3. bottom Plug the two fill holes with two aligned above the slots in the this time white plugs from the hardware bag first riser Sand is necessary to keep the steps from floating STEP 2 Cont d FOR ABOVE AND IN GROUND STEPS a Mm 10 Next push in and downward at 11 Align the tabs on the other side 12 Place the third flexible riser in to the center of tread to lock into the of the tread with the slots on the panel the groove on the second step and in stringers and tap down until seated to the slots on the side and back extensions The ventilation slots in the riser should positioned on the right side and aligned above the slots in the first and second risers Fill these holes with sand 13 Place the third tread over the 14 Fill the side and back ballast 15 Install the side ballast by placing side and back panels align the tabs with 10 lbs of sand each and plug the over the side extension panel and on the tread with the slots on panels fill holes using the two white plugs pushing down until seated a mallet and push down until seated from the hardware bag may be necessary 16 Repeat procedure to install the back ballast IF YOU HAVE ABOVE GROUND STEP SKIP STEP 3 AND GO TO STEP 4 Tools needed cordless drill with Phillips driver Parts needed 4 posts 2 handrails 2 deck connectors STEP Side trim back trim back trim extension E 8 10 X 1 1 4 self tapping screws
4. plugs TTT Wl n TUI Il Hit I I IM lli MM Tools Needed for Assembly Cordless drill with Phillips head Rubber Mallet Hack saw for 3 tread only Plastic funnel Liquid soad 70 LBS SAND REQUIRED Third Tread I Flexible Second I ME v Tools needed STEP 4 Parts needed cordless drill with Phillips driver rubber mallet 3 leveler tubes 5 round step pads back panel side panel back extension side extension back extension return stringer stringer extension side stringer and stringer brace FOR ABOVE AND IN GROUND STEPS Flat Bottom 2 threads exposed Tapered Bottom no threads exposed 1 Using a rubber mallet install three of the round step pads on to three of the leveler tubes A little liquid soap on the leveler tubes will make assembly easier Set the three assemblies and two round step pads aside 3 To make assembly easier apply a little liquid soap onto the four tabs then insert tabs into the openings on the lower back panel and push panels together Panels are designed to fit together tight it may require a rubber mallet if panels won t go together by pushing 6 Attach the back extension panel using three 10 x 1 1 4 self tapping SCrews 2 Next install one of the leveler tube assemblies into the lower side panel leaving two threads exposed for a flat bottom pool If pool bottom is tapered install leveler tube all the
5. way up so there are no exposed threads To install the leveler tube place the long tab on side of tube into slot on panel and tap down with rubber mallet 4 Install the second leveler tube assembly into the side extension panel This leveler tube assembly is fixed so there will be no adjustment in the slot on panel Tapered Bottom 7 Install the third leveler tube assembly into the back extension return leaving one thread exposed for flat bottom pool If pool bottom is tapered install leveler tube all the way up so there are no exposed threads 5 With the assembled panels from step 3 standing up attach the side extension using three 10 x 1 1 4 self tapping screws 8 Install the back extension return on to the back extension panel Push down until seated STEP 1 Cont d FOR ABOVE AND IN GROUND STEPS 9 Turn the assembly over so the lev eler legs are sitting on the ground 12 Insert the stringer assembly into the opening on the back panel and push down until seated 15 Align the two tabs on the stringer brace with the groove on the stringer and side stringer and push down until seated 10 Using three 10 x 1 1 4 self tapping screws one in every other hole attach the stringer extension to the stringer 13 Install the second round step pad over the round tab located on the bottom of the side stringer Again a little liquid soap will make assembly easier
6. 1 1 4 self tapping screws one leaning back install the flexible bottom attached at both ends Attach at the each in the outer holes located on the riser by placing over the tabs on the angled end first by measuring up 2 underside of center step Screws will stringers and into the groove on the and over 2 then using a 10 x 1 1 4 install at an angle underside of the bottom tread The self tapping screw go through the face angled cut on the riser will match the of the riser and in to the return panel angle on the return panel On opposite end measure up 2 and over to the first groove in the riser and Pour Sand into angle the screw so it will thread into the Stringer holes the raised tab on the panel 1 7 ib f z lt l I hi P Ll 1171 ni Ma 7 At this time pour 25 lbs of sand 8 Place the second flexible riser 9 Place the second tread over the into the stringer and 25 lbs of sand into the groove on the bottom tread stringers and onto the side and back into the side stringer Sand will be into the slots on the side extension extension panels Align the tabs on added through the holes located at and back extension The four one side of the tread with the slots on the top of the stringers As the stringer ventilation slots in the riser should be panel and push down until seated fills tap the sides to settle sand to the positioned on the right side and Only attach one side of the tread at
7. EFORE ATTEMPTING ASSEMBLY Back Handrail Post Side Stringer Trim 1 9 diameter 1 9 diameter Extension Brace Panel E fer e g ikum _ zi e i Back Ge Extension Panel Mm Em a Return Panel 2 Lower E mW n m a Side 54 lt OPEP VEMM m uS y A A lt 4 4 f TV Side p Stringer f NO l VV 490709 490710 490712 490711 490704 490719 490720 490707 490706 490718 490708 490713 490716 490717 490700 490701 490702 490714 490715 490725 490726 490727 490728 490729 stringer 1 stringer extension I side stringer 1 stringer brace 1 lower back panel back trim back trim extension back extension panel lower side panel side trim side extension panel return panel side ballast back ballast hand rail 1 9 diameter post 1 9 diameter deck connector 1 9 diameter leveler tube iot Botidm round step pad Tread left bottom tread Genter Bottom center bottom tread Tread right bottom tread second tread third tread Second Tread Right Bottom Tread Flexible Third Riser Flexible Bottom Riser Stringer Extension Pan PART DESCRIPTION NUMBER 490721 flexible bottom riser 490722 flexible second riser 490723 flexible third riser Lower Back el 490731 step hardware safety pack 10 x 1 1 4 self tapping screws white plugs safety labels tread
8. SAVE THESE INSTRUCTIONS DEALER INSTALLER GIVE TO HOMEOWNER OCEAN BLUE GRAND ENTRANCE POOL STEPS ASSEMBLY AND INSTALLATION MANUAL ABOVE GROUND FOUR TREAD MODEL IN GROUND THREE TREAD MODEL Part No 400700 Part No 400800 ean WATER PRODUCTS OCEAN BLUE FOUR TREAD STEPS For Above Ground Pools Model No 400700 Four Tread ASSEMBLY INSTRUCTIONS PLEASE READ BEFORE ATTEMPTING ASSEMBLY Ballast Handrail Post Side Stringer Back 1 9 diameter 1 9 diameter Extension Brace Panel Upper ip Side Panel 4 or gt _ d Oy m Extension ia a MW Ew Return Upper FSE 4 Panel Back 4 Panel gt Momm C We EN Side SEA i Lower Ballast e p olde 4 u x Panel Round PF Step J SID trea Pad i Leveler l Tube 4 Deck UE BT y 4 3 Connector aS i UN ie Side i c LE 1 9 diameter NS n gt Stringer Stringer 7 Stringer Lower Back Extension Panel QTY PART DESCRIPTION QTY PART DESCRIPTION Tools Needed for Assembly NUMBER NUMBER M M Cordless drill with Phillips head 490721 flexible bottom riser Rubber Mallet 490722 flexible second riser Hack saw for 3 tread only Plastic funnel 490709 stringer 1 490710 stringer exte
9. and attach using two 10 x 1 1 4 self tapping screws in each connector If you have a con crete deck you will need to purchase the proper fasteners for concrete SAFETY RULES IMPORTANT One person on the step at a time FOR YOUR SAFETY DANGER shallow water no jumping or Consult your local building department before df g Soren sie p or po al dlsek installation of your pool and equipment Check the contents of the carton with the parts list for this step ALWAYS have competent adult supervision when pool is in use DO NOT attempt to assemble or install this step e NEVER leave the pool unattended if there are ANY shortages of parts or hardware e NO unauthorized entry into pool Por proper assembly and installation follow all instructions in the sequence shown lo event entrapment OF drowning step must Before using the product after assembly and be installed up to the inside of pool wall installation go over the instructions and proce e Weight limit 400 Ibs gen to make sure nothing has been over Exceeding the recommended weight limit iocus cuit trien cae NOT may cause step to fail responsible for improper assembly or installation DANGER only use a cordless drill for assembly and installation NEVER use a corded electric drill in or around swimming pool WINTERIZING Disconnect the step from pool deck or outside safety ladder and carefully lift out of water Once out of water tip step on its back to drain
10. e panel in to the openings on the upper back panel and push together A little liquid soap on the tabs will make assembly easier 4 Place the fourth flexible riser on top of the third tread with the ends of the riser into the slots on the upper side and back panels The third tread does not have groove for the riser to set in to 2 Position the upper back side panel assembly over the lower back and side panel align the tabs with the slots on the panels and push down until seated mallet may be required imm nm Pu DU uuu ea 5 Place the fourth tread over the upper side and back panels Slowly push down making sure to align the top of riser with the groove on the underside of fourth tread 3 Attach the panel assembly by using one 10 x 1 1 4 self tapping screw in the back panel and one in the side panel at the recesses 6 insert the handrail posts into both holes on the fourth tread and push down until post stops A little liquid soap will make assembly easier 7 Insert the handrail posts into both holes on the second tread and push down until post stops Using the two plugs from hardware bag plug the two unused holes on the first tread 8 Slide a deck connector over each of the top posts A little liquid hand soap on the posts will make assembly easier 9 Rotate posts to align the flat side with the flat side on the handrail and install both handrails by tapping down with a rubber mall
11. et STEP 4 Cont d FOR ABOVE GROUND 400700 STEP ONLY 10 Attach the handrail to each post using one 10 x 1 1 4 self tapping screw repeat for the second handrail 11 Attach all four posts to the step panels using one 10 x 1 1 4 self tapping screw in each post STEP 5 Tools needed Cordless drill w Phillips driver rubber mallet Parts needed FOR ABOVE AND IN GROUND STEPS INSTALLING STEPS INTO SWIMMING POOL IT WILL REQUIRE 2 3 PEOPLE TO PLACE STEP INTO POOL 1 Place pool step in the water if you have an above ground pool be careful not to damage pool frame Hold the step away from swimming pool wall while it is filling with water 4 Attach the deck connectors to each handrail posts using one 10 x 1 1 4 self tapping screw 2 Step will float until all the air is out of step components this will take several minutes To remove the air it will be necessary to tilt the step back wards and to the left and right until the air bubbles stop Once the air bubbles have stopped the step should be sitting firmly on bottom of pool If not air is still trapped in components and step will have to be tilted again 5 Apply the two safety labels on the upper handrail posts so they are visi ble when entering the swimming pool 6 1 1 4 self tapping screws 2 safety label 3 Position the step close to the pool wall Rotate the two deck connectors to sit on to pool deck
12. nsion 1 490712 side stringer 1 490723 flexible third riser 490711 stringer brace 1 490724 flexible fourth riser 1 1 1 1 Liquid soad 1 490704 lower back panel 490731 step hardware safety pack 1 490703 upper back panel 29 10 x 1 1 4 self tapping screws 70 LBS SAND REQUIRED 1 490707 back extension panel 4 white plugs 1 490706 lower side panel 2 safety labels 1 490705 upper side panel 2 tread plugs 1 490708 side extension panel 1 490713 return panel Second 1 490716 side ballast Tread 1 490717 back ballast Right Bottom E 2 490700 hand rail 1 9 diameter Tread Tread 4 490701 post 1 9 diameter 2 490702 deck connector 1 9 diameter Third 3 490714 leveler tube Tread 5 490715 round step pad Left Bottom 1 490725 left bottom tread 1 490726 center bottom tread Center Bottom TUUS 1 490727 right bottom tread Tread JI Ill IM IUE Flexible Second 1 490728 second tread HIMMEL I BOARD Riser 1 490729 third tread Flexible Third DUAE 1 490730 fourth tread HN Riser Flexible Fourth Riser Back Trim Extension Side Trim Back Ballast Side Ballast Round Step Pad Leveler Tube Deck Connector 1 9 diameter Stringer QTY PART DESCRIPTION NUMBER CT WG WN AP lcl OCEAN BLUE THREE TREAD STEPS For In Ground Pools Model No 400800 Three Tread ASSEMBLY INSTRUCTIONS PLEASE READ B
13. water from panels After drained tip step on its front to finish draining water All the water must be drained from step before putting in to storage NOTE sand remains in step do not remove sand OCEAN BLUE WATER PRODUCTS WARRANTY Ocean Blue Water Products warrants their swimming pool steps to be free from defects in workmanship for one year from date of purchase DO NOT RETURN DEFECTIVE PART TO DEALER The defective part should be returned postpaid to Ocean Blue Water Products 4646 W Lake Street Chicago IL 60644 Enclose proof of purchase receipts etc showing date purchased your name address and daytime phone number You will be notified of cost to replace part This warranty gives you specific legal rights and you may also have other rights which may vary from state to state Made in U S A cean ELUE VVATER PRODUCTS Printed in U S A 01 14 11
Download Pdf Manuals
Related Search