P1410 User Manual - NWTruckworks.com
Contents
1. case of rough ground ground might be detected instead of object A 9 Not all obstacles is detected from 8 feet for instance a person is detected from 4 26 feet because of the weak reflection of clothes The distance form sensor A to B rather than C to D is shown Maintenance 1 Clean up the sand ice snow or any other dirt on sensors surface timely 2 Re paint is allowed on sensors surface with slight coat However extra thick paint may affect detection How to install e Tools System Components e Installation diagram 1410 Display rear positioning Controller 1410 Display la as No wires from Front positioning Controller to LCD Must power front LCD to constant 12 volt source Sensor Reverse Light e Installation procedures Sensor positioning Interval of sensors Sensors are installed on the position Mirror symmetry Drill holes in accordance with the diagram horizontally Make holes in bumper with included drill bit Display unit installation Controller installation Plug display unit into its pedestal The position of controller and adjust it to suitable position should be appropriate to gt The mounting surface must be clean both sensors Connection Connect the controller to e Installation of sensors 12V power supply sensors 1 Horizontal position X 0 66 0 98 feet Same height equally distributed wiring Making conne2. P1410 User Manual ER BULLY DOG FA Autero Reverse Backing Systems 866 805 6922 Contents Note Warning Product information Introduction seen Features and benefits Specifications How to use Display Volume Adjustment Precautions 2232222222222 sat cele ae Zee Sensing Range and Warning Method INDles esse 2 an een Zen ee 7 8 Maintenance How to install Tools 10 System Components 10 Installation diagram 11 Installation Procedure 12 Installation of sensors 12 Wire Connection 13 Precaution during installation 14 Final testing 14 Troubleshooting 14 Warranty 14 Note Please read this manual carefully before using this product This system is designed to be an aid and should not replace the need to drive carefully Under no circumstances will the manufacturer or supplier accept any responsibility or can be held liable for any direct or indirect incidental or consequential damage or for injuries r
3. ctions with assistant tools Make sure the recessed sensor surface facing upwards slightly while keeping the whole sensor body horizontally Test To check if the parking assistance system works properly 2 H 1 64 2 30 feet 2 Vertical level The surface to install sensors need to be vertical and flat Connect the red wire of controller to the reversing light s positive and the black to the negative The wiring card usage refers to the following diagram 3 Direction of sensor Note The E shape contact must be fully pressed e Wire Connection e Precaution during installation 1 Do not scratch the surface of bump during drilling holes Do not cut or damage the wire in any circumstance Make sure the power cable is connected correctly The controller should be secured n a water proof location The surface to mount the display must be clean Make sure all the connection is correct before final testing Any problem could refer to the Trouble shooting section e Final testing l 2 Use one selected object to test the sensing distance and warning as stated in page 7 Use one selected object to check if each sensor is in the right position If the system detected something which 1s not existed adjustment is needed for the controller peel off the QC label in the back of controller screw anticlockwise until the signal cleared out e Troublehooting No display during revers
4. esulting from installing or use of this system Manufacturer or supplier does not warrant the accuracy or completeness of the information n this documentation and manufacturer or supplier reserve the right to alter specifications without notice To the extent permitted by law manufacturer or supplier exclude all liability including negligence for any loss incurred in reliance on the contents in this publication Warning Please practice reverse parking using different obstacles to test this product s performance Though the minimum detecting distance is 1 15 feet it is still recommended to keep enough space to stop the car Considering the cars inertia t would be better to stop the car when the distance is shorter than 2 feet The reverse speed should be less than 3 miles hour Products information WN Introduction The system alerts the driver the distance of obstacles while reversing the vehicle It includes 4 sensors 1 waterproof controller and display The system generates both audible and visual warning Features and benefits Accurate measurement and stable readout High sensitivity wide detection range and small blind area Functions include digital display sound alarm zone amp direction indication reverse reminder Self testing The outfit of display unit matches the instrument panel of car Applicable to most cars and easy installation e Specifications Sl Ot a Operation v
5. ing Wrong orientation indication Constantly display p Display a fixed distance Orientation indicator not on Warranty e year a No power b Display unit is not connected to controller properly The sensor s position is wrong An object within 0 89foot is detected all the time a Ground 1s detected b Sensors direction is wrong Sensor s connector is not plugged in properly or is plugged in while power is on Possible Causes Make sure all the connection 1s correct Change sensors position Adjust the sensors position or angle Adjust the sensors position or direction Check if the connector is firmly connected Then witch on power again e Any physical damage will void the warranty
6. nce Display 1 15 p Green Yellow Red light Light light Zone Indication 4 f P l Sound Alarm No Sound with Sound with Rapid Continuous Sound Long Intermit Short Intermit Sound Sound Notes Please check the condition behind your car before reversing In some cases the display may be not as same as the reality due to the sensor position obstacle shape reflection condition and so on Some examples are given below As B is under the level of sensors and A is a strong reflecting point the distance of CA will be shown first When the obstacle is within the blind area both A and B will not be detected This will occurs when the obstacle is lower than the level of sensors Due to obstacle A is pretty short so during reversing the distance between sensor and obstacle A shown first After obstacle A is within blind area the distance between sensor and obstacle B will be shown Though A 1s closer to the car than B the distance from sensor to point B is shown In case of small angle of incidence to the obstacle such as glass or other smooth plane the obstacle s not detected 5 B will be detected sooner or later but A may not be detected at all 6 The reading may moves up and down between 3 9 feet and 7 2 feet because the low obstacle A is at the critical detecting point The reading will be stable after a little bit closer to the obstacle A 7 On certain conditions for example in
7. oltage Power consumption Operation temperature Detection distance Display resolution Detecting error Detecting rate DC 10V 16V lt 4W 35 C 70 C 1 15 8 00 feet 0 Olfeet 0 06 feet A times sec How to use P1410 display unit ggg Sound Alarm Zone Indication Reverse BACKING SYSTEMS Distance Display Direction Indication P 1410 Display e Power The system is automatically activated when the reverse gear is engaged Self testing program will be done right after the system is powered on After the buzzer beeped and the direction indicators on the system is ready The LCD unit is plugged into black receiver box and this receive box must be tapped into a constant 12 volt source in the front of the vehicle e Display 1 28 Distance between sensor and obstacle Rey _____ Indicate the closest obstacle direction using flashing LED or icon om _ Indicate zone stage with a pointer or car icon e Volume Adjustment There are 10 volume levels The toggle switch can be moved to the right and left pushing to the right will increase volume and to the left will decrease down to mute e Precautions Reverse speed should be less than 3 miles hour to avoid accidents and give you a chance to respond to backup sensor Danger zone start 2 feet away from obstacle Thin and small obstacles can be detected at shorter range only e Sensing Range and Warning Method Dista
Download Pdf Manuals
Related Search