Home

CFX-750 Display User Guide

1. Manual Use the icons on the guidance screen to control when the path is recorded To start recording tap Sa to stop tap So Record with coverage Automatically begin and end recording the FreeFrom pattern when coverage logging begins and ends Note You can still use the FreeForm recording icon to manually override recording Headland Infill Switching Use this setting to choose how guidance switches between the headland and the infill part of the field Select this mode To Automatic Automatically switch from headland to infill when the vehicle moves inside the inner headland boundary Manual Use the icons on the guidance screen to select when guidance switches from headland to infill Boundary setup Use the Boundary Setup option to configure e when boundaries are active See Boundaries below e how the display records boundaries See Expand Boundaries below Note the following e When you record a boundary the display automatically calculates the area of the boundary and displays this information on the Status tab e When you load a field that contains a boundary the boundary also loads e Youcan record multiple boundaries in a single field e If your variable rate controller has section switching capability a boundary acts as a switching barrier When you move outside the boundary the controller will automatically switch off the implement CFX 750 Display User Guide 107 6 Mapping and Guidance
2. For more information on configuring the LH 5000 controller refer to the LH 5000 instruction manual Advanced Use the Advanced option in the Implement screen to configure the following e Boom Setup e Swath Control e Rate Control e Target Rate e Turn Off Rate on Overlap e Rate Snapping Boom Setup Note The boom setup on the CEX 750 display must match the setup on the LH 5000 controller If the boom setup differs between the display and the LH 5000 controller a warning message appears on the display Use this option to view and adjust the following settings Setting Notes Implement width Enter a width between 1 00 328 01 0 30 99 99 m Fence Nozzles Enter the locations of any fence nozzles Number of sections Enter a number between 1 10 Swath Control Use this option to view and adjust the following settings Setting Notes Boom control Enter a width between 1 00 328 01 0 30 99 99 m Coverage switching overlap Control the amount of boom switching overlap allowed before the section will be switched by the system Enter a value between 1 99 Boundary switching overlap Control the amount of overlap on a boundary before the boom section is switched off Enter a value between 1 99 On Off valve latency Tune the section switching to allow for hardware delays Enter a time between 0 0 10 0 seconds Intentional overlap Set a distance to be overlapped when moving to an unsprayed
3. e Ensure that the tire pressure is correct e Complete the GPS Setup on the CFX 750 display For more information see Chapter 7 GPS When you calibrate your auto steer option pay attention to the following e Choose a field with the smoothest possible surface and perform the calibration at the normal operating speed for the vehicle e Fora high clearance sprayer perform the initial calibration without an implement or with the booms folded in After the initial calibration is completed you can fine tune the settings with the implement or booms folded out The calibration process requires a straight AB line If you do not create an AB line before you begin the calibration the system prompts you to open a field and create one To access the auto steer options 1 Inthe guidance screen tap AH and then tap Vehicle 2 Tap Auto Steer K r mG gt gt 48 CFX 750 Display User Guide Vehicle 4 The EZ Steer assisted steering system The EZ Steer assisted steering system works with the CFX 750 displays internal GPS receiver to provide vehicle guidance As such you must complete the GPS setup before you calibrate set up or run your EZ Steer system See Chapter 7 GPS Setup To view and adjust the settings for the EZ Steer system 1 Inthe guidance screen tap 8 and then tap Vehicle kad 2 Tap Auto Steer and then EZ Steer Setup Mao w gt s Note If the EZ Steer Setup button does not appear tap
4. AAA RAEE eae eee ee ee a eee 121 TOO ETIE 2244574806844 oa eek 6 eee iras rata hee Eas 122 GPS DCU saea reheat hate Stee Phe eee eee ae he bee eae ee Bee 122 Position UA raros aos daw ae a he oh eee ee ee eee ee AA aaa 122 A E 123 ATENTA A emos AREA aa as 125 Use SBAS satellites in the position HX 123 ei IA AS 124 Gac so oaw en cea isa e ea eeae ey ise ee ee ee eo ha eee ees 4 124 Saco Cd cee ah eet a eae Bes eee ee ee hae ee ee Se 124 DlUGWS ropas teh eee be eee ek Gee ee eee eee See he Oe ee 124 P o 64 Gok tee Gk eee OB eee Nee eee ee ee ees eee A ee 124 ii AUS 2a 4 aa gid Bonen ea ee oa Aenea oe ee A ee ee 124 IGP Orta bee ee hee eek Geta narra E 125 PEG D een ac aueee e ee ee ses eee eae nee as eh es 125 5 ee ee ee ee ee eee ee ee ee ee ee ae 127 ii A oR 4646065 400 ee eee ee ee hee hekee bees ee as 128 DCM SUC OC puso ye boas ome ee sara se hess eae eee ee eee 128 Sa enero ee eed he BAe Ee eee bes 128 Configuring the display for VRS corrections ooo 130 Soma doo restec 4 26 4088 he 6 54d oe ee a ee hee bene sees 131 Connected Farm Cll 62 ebak au fou eens oS rro ED OA Eee bee eee eee Obese 132 a A e 228 oes ee cet ee oes ee eae hens een ees eno ees ae 132 Device Mae othe nee be tie eee ee Gee ee Chee eS eo eee oe ee ors 133 Modenton Se aeenceseaceee arson aaa ee ape eye rato 133 Networkregistrationi os esarete saetti apinta nna a4 cea eee eed aa R 134 Connected Farm data transfer acia css ron snti eee Dee ew ee ee
5. Run screen overhead view Description Description Manual section control Section control off Automatic section control A Coverage logging on Target rate Coverage logging off 44 CFX 750 Display User Guide Guidance icons eon Description Guidance pattern select Pause guidance Nudge left Nudge right Record FreeForm guidance pattern Set A point Set B point Shift AB line Next AB line Map rock point feature Getting Started 3 Start recording headland Pause recording headland End headland recording Cannot engage auto guidance Ready to engage auto guidance Auto guidance engaged Increase auto guidance aggressiveness Decrease auto guidance aggressiveness eon Deseription Mapping configuration Area feature CFX 750 Display User Guide 45 3 Getting Started 46 CFX 750 Display User Guide CHAPTER Vehicle In this chapter This chapter describes how to configure your auto steer system for use with the CFX 750 m Introduction display m The EZ Steer assisted steering system m The EZ Pilot assisted steering system m The Autopilot automated steering system CFX 750 Display User Guide 47 4 Vehicle Introduction To ensure the proper performance of your auto steer system you need to calibrate it correctly Before you calibrate your auto steer option do the following e Ensure that the vehicles hydraulic oil is up to operating temperature Refer to the vehicle documentation
6. Set a Back Offset when the implement is behind the antenna on the back of the vehicle for EZ Steer systems or behind the fixed axle of the vehicle for Autopilot systems Choose the type of implement mount that is in use After you have defined a guidance line there are two ways to get guidance e Drive the vehicle through a tight U turn The next guidance line appears e Ifyou are manually logging a FreeForm curve tap to stop defining the current line The FreeForm curve is similar to an adaptive curve You must record your line on each pass to receive guidance on the next If the vehicle is not drawing a line or guidance trail behind it you are not recording your path and therefore the next guidance line will not appear Note Do not confuse the existing guidance line with the guidance trail appearing behind the vehicle that shows your current guidance You need to create a new guidance line to receive guidance on the Next pass Using guidance on straight segments When driving on straight AB lines you do not have to record your path because the guidance lines are generated automatically CFX 750 Display User Guide 109 6 Mapping and Guidance Creating straight sections on Headland or Curve swaths To create straight sections when recording headland or curve swaths l Tap Sa 2 Drive the section 3 Tap SO to finish recording the straight section and to start recording a curve again Fields A field
7. is specific area of land where events such as planting seed or applying fertilizer are carried out You create your first field when you first configure your implement see Starting Guidance page 108 That field remains open until you do one of the following e Create a new field or load a previously saved field e Calibrate your EZ Steer system e Perform a hard reset Note Fields are stored automatically You do not have to actively save a field The following sections describe how to use the field function when there is already a field currently loaded on the display Creating a new field 1 Inthe guidance view tap I The Finished with Field screen appears 2 Tap Yes 3 In the Create New or Select Old Field screen tap Create New Field 4 To setup the new field progress through the wizard 5 Follow the on screen instructions to drive your new line For more information see Mapping an AB line page 114 Selecting loading a field 1 Inthe guidance view tap lip The Finished with Field screen appears 2 Inthe Finished with Field screen tap Yes 3 In the Create New or Select Old Field screen tap Select Field by Name 4 Inthe Select Field by Name screen select the field you wish to load 5 To setup the field progress through the wizard 110 CFX 750 Display User Guide Mapping and Guidance 6 Adding an AB line to a current field To create a new AB line in a current field 1 Inthe guidance view tap I The
8. Engage status Icon color Ready to engage O Engaged A Cannot engage Z After using the Autopilot automated steering system e Any time that you are not using the system pivot the Autopilot automated steering system motor away from the steering wheel e Before you leave the vehicle turn off the system power switch or remove the power plug 66 CFX 750 Display User Guide CHAPTER Implement Application Controller In this chapter Introduction Field 1Q HARDI 5500 controller Raven controllers Rawson controller Amazone controller LH 5000 controller Checking the implement connection This chapter describes how to configure the CFX 750 display to use an implement application controller CFX 750 Display User Guide 67 5 Implement Application Controller Introduction The options in the Implement screen enable you to configure an implement application controller such as the Field IQ crop input control system To access the Implement screen L 1 From the guidance screen tap S 2 From the Settings screen tap Implement Implement i L The Implement screen contains two options Advanced and Initial Setup The Advanced option only appears after you have set up your controller via the Initial Setup option To set up your controller 1 From the Implement screen Tap Initial Setup The Controller Type screen appears Controller Type Which controller do you have connected ae Note To a
9. Enter a value between 1 99 On Off valve latency Tune the section switching to allow for hardware delays Enter a time between 0 0 10 0 seconds Intentional overlap Set a distance to be overlapped when moving to an unsprayed area or out of a sprayed area Enter a distance between 0 00 32 10 0 00 10 00 m 100 CFX 750 Display User Guide Implement Application Controller 5 Rate control Use this option to view and adjust the following settings Setting Notes On Application rates are sent from a prescription loaded in the display or the target rate manually configured on the display Off The target rate must be set on the LH 5000 controller The CFX 750 display does not send target rates to the controller This is the default setting Note When sending a target rate to the LH 5000 controller that is higher than 99 9 the display rounds to the nearest whole number For example 0 99 9 is not rounded 101 4 is rounded to 101 Target Rate Set the target application rate that will be sent to the LH 5000 controller Enter a rate between 0 0 11000 0 Single section boom switching Use this to turn off the implement in areas that have already been applied Note This setting can only turn the entire boom on and off It does not support individual sections e Select Yes to avoid spraying an area that has previously been sprayed e Select No to spray an area that has previously been sprayed Checking the imp
10. Pull the USB drive out of the USB socket Taking a screenshot Occasionally you may want to save a screenshot of the touchscreen for example to provide information for troubleshooting purposes When you take a screenshot the display saves a png file to the root directory of the USB drive Note Screenshot capability is only available when there is a USB drive inserted in the display To take a screenshot 1 Press both brightness control buttons at the same time 2 Hold the buttons down until the touchscreen flashes A N CAUTION Do not remove the USB drive from the socket while the display is writing to or from the drive This will corrupt the data The Quick Start Wizard The Quick Start Wizard enables you to configure important settings before you begin driving The first time that you turn on the display the wizard starts automatically Make sure that when you first turn on the display that you run the entire wizard When you run the wizard you can choose whether or not it appears every time the display is turned on If you choose to hide the wizard when you next power up the display the guidance screen automatically appears However you can still access the wizard at a later time as follows 1 Tap S and then tap ul 2 Tap Quick Start Wizard The Welcome screen appears 32 CFX 750 Display User Guide Getting Started 3 3 Tap The first page of the Quick Start Wizard appears Units Select your prefe
11. We call this license the Lesser General Public License because it does Less to protect the user s freedom than the ordinary General Public License It also provides other free software developers Less of an advantage over competing non free programs These disadvantages are the reason we use the ordinary General Public License for many libraries However the Lesser license provides advantages in certain special circumstances For example on rare occasions there may be a special need to encourage the widest possible use ofa certain library so that it becomes a de facto standard To achieve this non free programs must be allowed to use the library A more frequent case is that a free library does the same job as widely used non free libraries In this case there is little to gain by limiting the free library to free software only so we use the Lesser General Public License In other cases permission to use a particular library in nonfree programs enables a greater number of people to use a large body of free software For example permission to use the GNU C Library in non free programs enables many more people to use the whole GNU operating system as well as its variant the GNU Linux operating system Although the Lesser General Public License is Less protective of the users freedom it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified versio
12. A FreeForm Use this pattern type to create curved and straight lines for guidance in fields of any shape The display records the exact path you drive and uses this to generate the next guidance line To select the FreeForm recording option 1 Inthe Settings screen tap Guidance and then FreeForm Recording une 2 Tap Manual or Record with coverage Recording a FreeForm curve 1 Drive to the start point of the FreeForm curve Zi To use Manual recording tap SA Record with Coverage tap either or lt a 118 CFX 750 Display User Guide Mapping and Guidance 6 While the display is recording the current path SO appears on the guidance screen 3 Drive the curve To record straight sections you can use the pause feature See Creating straight sections on Headland or Curve swaths page 110 4 To finish recording do one of the following If Auto U Turn Detection is on perform a tight U turn For Manual recording tap SO Ifyou are using Record with Coverage tap SO or DE Note If Auto U Turn Detection option is off you must manually stop recording at the end of each pass and then start recording again at the beginning of the next pass Using the FreeForm pattern to define a straight AB line 1 Tap A and then drive to the end of the line 2 At the end of the line tap Switching to another line To switch from the current FreeForm guidance line to another tap i l The first ti
13. Auto Steer System Type and then select EZ Steer for your controller The EZ Steer Setup screen contains the following options e Engage Options e Vehicle Setup e Aggressiveness e EZ Steer Demo e EZ Steer Calibration Wizard The following sections describe each option CFX 750 Display User Guide 49 4 Vehicle Engage Options Use this option to view and adjust the settings described below Setting Minimum Maximum speed Maximum Angle Engage Disengage Offline Override sensitivity EZ Steer external switch EZ Steer operator timeout Notes Enter the minimum and maximum speeds at which the EZ Steer system will disengage e Minimum between 1 0 and 15 9 mph 1 6 and 25 5 kph e Maximum between 1 0 and 18 0 mph 1 6 and 28 8 kph The EZ Steer system will not engage when the vehicle is heading toward the guidance line at an angle greater than the Maximum Angle Enter an angle between 5 and 45 degrees Engage offline The system will not engage when the vehicle is offline further than the Engage Offline distance Enter a distance between 0 5 and 27 0 0 2 and 8 2 m Disengage offline The system will automatically disengage when the vehicle is offline further than the Disengage Offline distance Enter a distance between 0 6 and 27 00 0 2 m and 8 2 m Control how much force is required to disengage the system Enter an increment between 1 100 Enable or disable additional safety features
14. Boundaries Select this mode To Enabled Use existing boundaries and create new ones for all your fields Disabled for this field Turn off boundaries for only the current field you are working in When you begin your next field the option will automatically change to Enabled Disabled for all fields Turn off boundaries for all fields you work in including boundaries made with headland patterns Expand Boundaries Use this setting to determine how the display manages the boundary after you finish recording If you select this mode The boundary will Do not expand Not alter once you have finished recording Half swath width Expand by one half swath width toward the outside of the pass One swath width Expand by one full swath width toward the outside of the pass Starting Guidance Before you can use the display for guidance you must configure your implement 1 From the guidance screen tap UII and then tap Create New Field 2 Inthe Create New Field screen tap Implement Setup 3 Edit the settings for each option For more information see Implement Setup options page 108 4 Select a pattern type see Guidance Patterns page 113 and continue through the wizard Implement Setup options For optimum guidance make sure that you enter accurate information for the implement that is attached to the vehicle Incorrect information may result in gaps and overlaps in coverage The following table describes each of the I
15. Canada This apparatus complies with Canadian RSS GEN RSS 310 RSS 210 and RSS 119 Cet appareil est conforme a la norme CNR GEN CNR 310 CNR 210 et CNR 119 du Canada Australia and New Zealand Class A Statement Attention This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Australia and New Zealand This product conforms with the regulatory requirements of the Australian Communications Authority ACA EMC framework thus satisfying the requirements for C Tick Marking and sale within Australia and New Zealand Notice to Our European Union Customers For product recycling instructions and more information please go to www trimble com ev shtml Recycling in Europe To recycle Trimble WEEE Waste Electrical and Electronic Equipment products that run on electrical power Call 31 497 53 24 30 and ask for the WEEE Associate Or mail a request for recycling instructions to Trimble Europe BV c o Menlo Worldwide Logistics Meerheide 45 5521 DZ Eersel NL Safety A A Warnings A gt FP D Always follow the instructions that accompany a Warning or Caution The information they provide is intended to minimize the risk of personal injury and or damage to property In particular observe safety instructions that are presented in the following format WARNING This alert warns of a poten
16. Disabled or Manual CFX 750 Display User Guide GPS In this chapter This chapter describes how to set up the GPS l receiver Introduction GPS Setup Position Quality Advanced Status CFX 750 Display User Guide 121 7 GPS Introduction The GPS menu enables you to select which GPS system and correction source to use and the GPS quality tolerance To access the menu 3 1 From the guidance screen tap S E 2 From the Settings screen tap GPS GPS Setup Use the GPS Correction Source screen to choose the type of GPS position corrections that you want to use Source Description SBAS Free satellite based corrections Satellite based e WAAS Wide Area Augmentation System in North America augmentation system EGNOS European Geostationary Navigation Overlay Service in Europe OmniSTAR VBS Satellite based subscription correction service OmniSTAR XP HP High accuracy satellite based subscription correction service RTK Radio broadcast corrections from a ground based reference station Real Time Kinematic Uncorrected No GPS corrections Position Quality GPS signals can be disrupted by foliage or when the machine moves out of sight of one or more satellites or when one or more satellites move out of sight of the machine or set below the horizon 122 CFX 750 Display User Guide GPS 7 The Position Quality screen provides options that allow you to operate when the quality of GPS position informa
17. Enter a time between 1 60 minutes Vehicle Setup Use this option to view and adjust the settings described below Setting Vehicle type Wheelbase Antenna height Antenna to axle offset Angle per turn Freeplay left right Motor speed Motor direction is reversed Sprayer steering delay Swather steering delay Notes Enter the type of vehicle on which the EZ Steer system will be installed See Entering vehicle measurements page 52 See Entering vehicle measurements page 52 See Entering vehicle measurements page 52 Adjust the angle that the wheels turn during one full rotation of the steering wheel Enter an angle between 2 149 degrees Adjust this setting if the vehicle is consistently off to the right or left of the guidance line Enter a measurement of 0 12 0 30 48 cm Control the speed of the EZ Steer drive wheel motor Select yes or no Account for time lags with vehicle steering Enter a value between 0 1 1 5 Account for time lags with vehicle steering Enter a value between 0 1 1 5 50 CFX 750 Display User Guide Vehicle 4 Aggressiveness Use this option to view and adjust the settings described below Setting Notes Online aggressiveness Control how aggressively the EZ Steer system corrects deviations from the guidance line Enter a value between 50 150 Approach aggressiveness Control how fast the EZ Steer system steers the vehicle onto the guidance line Enter
18. Finished with Field screen appears 2 In the Finished with Field screen tap No 3 In the Create New or Select Old Swath screen tap Add AB Line 4 To setup the new field progress through the wizard 5 Follow the on screen instructions to drive your new line For more information see Mapping an AB line page 114 Selecting loading an AB line into a field 1 Inthe guidance view tap lip The Finished with Field screen appears 2 Inthe Finished with Field screen tap No 3 In the Create New or Select Old Swath screen tap Select Old 4 To setup the new field progress through the wizard 5 Follow the on screen instructions to drive your new line For more information see Mapping an AB line page 114 Record keeping Optionally you can record operational and environmental information about each field that you create including e Operator e EPA license number e Harvest year e Farm location e Vehicle e Implement e Application method e Wind speed e Wind gust speed e Wind direction e Sky conditions e Soil conditions e Temperature e Humidity e Crop e Target pests e Applied material Additionally there are four custom fields where you can enter your own values To learn how to use this information see Chapter 8 Data CFX 750 Display User Guide 111 6 Mapping and Guidance Resetting guidance To reset guidance in the guidance view tap ln The Finished with Field screen appears Finished with Field Have you fn
19. IQ or a variable rate controller Boom setup Use this option to view and adjust the following settings Value Notes Implement width Enter the width of the current implement The display uses this value to automatically calculated the swath spacing Enter a width between 1 00 328 01 0 30 99 99 m Boundaries See Boundary setup page 107 Number of sections Enter the number of sections you want to control on the implement Enter a number between 1 10 Refill Use this option to view and adjust the following settings Setting Notes Current volume Set the current volume of the tank or bin Refill method Choose from one of the following options e Refill to fill the tank or bin to the top e Partial Refill to add a specified amount to the tank or bin when you select Partial Refill Now from the Refill screen Refill Now Partial Refill Now Use this option to refill the tank or bin 38 CFX 750 Display User Guide Getting Started 3 Section Switching Setup Use this option to view and adjust the following settings Setting Notes Coverage switching overlap Control the amount of boom switching overlap allowed before the system switches that section Enter a percentage between 1 99 For e Less skip Set a high percentage when total coverage is essential The system will turn off sections when they cover a larger percentage of any fully covered areas This may cause some double cov
20. Turn left or right for the next swath As you move toward the next swath it appears on the screen and turns orange to show that it is selected A line An A line is a straight line defined by a single A point on the line and the heading of the line When you create an A line you must enter a heading in the A Heading screen By default the A heading is the same as the previous AB line An A line is useful when you need guidance exactly parallel to the last AB line for example when e driving adjacent fields e mapping the AB line on a road down the side of the field e skipping an access road in a field The A line extends 1 km 0 6 miles before and after the A point Mapping an A line 1 Drive to the start point of the master line 2 Tap A and then drive to the end of the line Because you have already set the line heading the master AB line appears on the screen 3 For guidance down the first swath follow the AB line 4 Turn left or right for the next swath As you move toward the next swath it appears on the screen and turns orange to show that it is selected 114 CFX 750 Display User Guide Mapping and Guidance 6 Identical curve The identical curve pattern records your exact route between the A and B points instead of creating a straight line All subsequent guidance lines will match the master curve regardless of where you drive the vehicle Use the identical curve pattern when you want to work a
21. a value between 50 150 EZ Steer Demo Use this option to access the EZ Steer Demo Mode EZ Steer Demo Mode is useful for practice with defining fields coverage logging and assisted steering EZ Steer Demo Mode requires an EZ Steer controller motor and EZ Steer simulator stand P N 54836 00 EZ Steer Calibration Wizard The EZ Steer Calibration Wizard guides you through the process of calibrating your EZ Steer system Calibration Before you begin to use the display you must calibrate the EZ Steer system To do this complete the Quick Start Wizard see The Quick Start Wizard page 32 that appears the first time that you use the display To calibrate the EZ Steer system at a later time complete the following process 1 Inthe guidance screen tap AH and then tap Vehicle 2 Tap Auto Steer and then EZ Steer Setup Auto Steer K m Sa gt gt gt Note If the EZ Steer Setup button does not appear tap Auto Steer System Type and then select EZ Steer for your controller CFX 750 Display User Guide 51 4 Vehicle 3 Inthe EZ Steer Setup screen tap EZ Steer Calibration Wizard The wizard guides you through the following processes Entering your vehicle measurements 2 roll calibration EZ Steer calibration Note To complete the above processes you must have GPS connected Entering vehicle measurements For optimum guidance you must take accurate vehicle measurements and enter them into the displa
22. change liquid rate Field IQ Rawson Control Module s needed Spreading rate control using a Rawson Drive Field IQ Rawson Control Module s needed Definition A number of rows or spray nozzles that are controlled by Tru Count air clutches or Tru Count LiquiBlock valves or boom valves A section can have either a single row nozzle or multiple rows nozzles depending on how the system is set up The individual row unit which material comes from on the implement This can be controlled individually as a single row section or as a group with other rows in a multiple row section Master on off jump start auto manual switch rate selection and increment decrement switch See Field IQ master switch box page 79 Required for section control Manually control sections rows See Field IQ 12 section switch box page 80 Controls 12 sections rows per module with up to 4 modules 48 module sections rows Controls 12 sections and application rate for spraying spreading and NH3 Controls 1 Rawson variable rate drive per module with up to 4 modules Included in planter NH3 and strip till platform kits Units of measure Type Seed Granular seed Liquid application Granular fertilizer NH3 Unit Metric US Imperial Metric US Imperial Metric US Imperial Metric US Imperial Metric US Imperial Metric US Imperial Symbol kS ha kS a kg ha Ibs a L ha Gal a kg ha Ibs a kg NH3 Ibs NH3 kg N lbs N Descripti
23. field with gentle curves Mapping an identical curve 1 Drive to the start point of the curve 2 Tap A and then drive the initial curve 3 When the icon is highlighted tap 18 The master curve appears on the screen 4 Turn left or right for the next swath As you move toward the next swath it appears on the screen and turns orange to show that it is selected Adaptive curve The adaptive curve pattern provides guidance along a curve and updates guidance after each swath to take into account any deviations you make It continually records your path and provides guidance that matches the last path you drove Mapping an adaptive curve You can map an adaptive curve either manually or automatically The method you use depends on the Auto U turn detection setting To change the Auto U turn detection setting 1 Inthe Settings screen tap Guidance 2 Tap Turn Settings then Auto U Turn Detection 3 Ifyou want to map the adaptive curve Automatically select On Manually select Off To map an adaptive curve with automatic turn detection 1 Drive to the start point of the curve 2 Tap A and then drive the initial curve 3 At the end of the first curve perform a U turn The system detects the turn and generates the next swath To map an adaptive curve manually CFX 750 Display User Guide 115 6 Mapping and Guidance w N Drive to the start point of the curve Tap JA and then drive the initial curve A
24. internal memory is full Operational hours This is the number of hours that the CFX has been operating Upgrade options The status of optional features and extensions Fault history Those faults that have occurred recently they may not be currently active CFX 750 screen The CFX 750 screen displays two options e About the Display This screen displays information about your CFX 750 display including the current version and the serial number e Restore Defaults Restore the display defaults to clear all of your current settings Note that if you choose to restore the default settings your display and lightbar will restart Recalibrate touchscreen The first time you power on the display you must calibrate the touchscreen See Power up page 28 Ifthe current calibration does not read your selections accurately use the Recalibrate Touchscreen option to adjust the responsiveness of the touchscreen Alternatively do the following 1 Power off the display and then power it on 2 Wait until the status bar at the bottom of the second startup screen is more than half full 148 CFX 750 Display User Guide System 9 3 Press both brightness control buttons at the same time 4 Hold the two buttons down until the display beeps CFX 750 Display User Guide 149 9 System 150 CFX 750 Display User Guide
25. learn how to change these settings on the CFX 750 display see Advanced below Set the baud rate to 9600 To enable the CFX 750 display to change the rates on the controller you must also set the Rawson controller to GPS mode 1 Turn the Rawson controller on 2 Press the MODE button twice 3 Press the SET button to switch the controller between GPS and non GPS modes Note If you do not set the Rawson controller to use GPS mode the CFX 750 display will only log the rates being used For more information on configuring the Rawson controller refer to the ACCU RATE Controller 9 2A User Guide CFX 750 Display User Guide 87 5 Implement Application Controller Advanced Use the Advanced option in the Implement screen to configure the following e Boom Setup e Swath Control e Target Rate e Default Rate e Step Size e Rate Snapping Boom Setup Use this option to view and adjust the following settings Setting Notes Implement width Enter a width between 1 00 328 01 0 30 99 99 m Number of sections Enter a number between 1 10 Swath Control Use this option to view and adjust the following settings Setting Notes Boom control Enter a width between 1 00 328 01 0 30 99 99 m Coverage switching overlap Control the amount of boom switching overlap allowed before the section will be switched by the system Enter a value between 1 99 Boundary switching overlap Control the amount
26. lt UI gt Field Wu Guidance ALS RA Mapping gi ea Can t engage Too slow Autosteer Setup T 20 0 gal a A 0 0 galia 10 ae A ee Item Description Notes 1 Quick Access icon See Quick Access icon page 38 O Boom section status Shows the current state of each boom section indicators e Green Enabled and spraying e Gray Enabled but not currently spraying e Red The section is off the switch is off Target rate If a prescription is loaded P displays to indicate that the prescription rate is being used rather than the target rate O Actual rate As the HARDI controller does not report the actual applied rate to the display this item always appears as N A O Section control Shows the current mode for the controller CFX 750 Display User Guide 83 5 Implement Application Controller Item Description Notes Fence nozzle indicator This indicator appears only when a fence nozzle is enabled Fence nozzle status is represented with the same colors as the boom sections see below Note The CFX 750 display cannot automatically turn fence nozzles on or Off It only displays the current status Application indicator The wheel on the display spins when the HARDI master switch is on and the booms are on Raven controllers When using the Raven SCS 400 and 600 series controller with the CFX 750 display note the following The CFX 750 display cannot control the status of the Raven controller master
27. modem with a passcode i 2 To view the status of the modem unlocks select the Wrench icon and then select System Turn on the modem and then connect it to the displays USB port Select the Wrench icon and then select System Unlock Upgrade Unlock Upgrade 2 Pasaword Upgrade Enter the passcode When prompted select Yes to restart the modem Enter Lockcode y 59380 TRG31 00000 29134EC9 0000000000 300009800 Be Unlock DCM300 Comgratulations Tour DCM3IGO la success ando ec Status Upgrade Options 8 CFX 750 Display User Guide 129 8 Data To use VRS corrections you must unlock the File Transfer VRS Internet and WiFi options Upgrade Options Orn WAHE Unlocked ATEK e gS Unlocked Variable Rata Unlocked Paricodea Expiration Dat Het Present DCM Spa Sh 5107510065 Firewire Veralori 11857 PROG REL 1 1 0 Celular Parameter Modicatiorn Locked Ag Vehicle Bus Locked File tranafer WAS Internet and WiFi Locked DCM 300 upgrade option Description Cellular Parameter Modification Needed for DCM 300G modem when the customer supplies their own SIM card Ag Vehicle Bus Future functionality File Transfer VRS Internet and WiFi Required for the use of VRS or Connected Farm Sync functions Configuring the display for VRS corrections Note The display must be unlocked for RTK to use the Trimble VRS correction type 1 To access the GPS Setup screens select the Wrench icon a
28. of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits TRIMBLE is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment Unauthorized changes or modifications could void the user s authority to operate the equipment This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Responsible Party Trimble Navigation 935 Stewart Drive Sunnyvale CA 94085 Telephone 1 408 481 8000 Canada This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du
29. or boom switches This means that the operator must remain in complete control of the sprayer at all times The CFX 750 display cannot automatically turn off the sprayer when going outside headlands across exclusion zones or previously sprayed areas The sprayer may not always switch off completely when the CFX 750 sends a zero rate This means the operator may need to manually turn off the master switch to ensure that spray is not applied Note The only time the CFX 750 display sends a zero rate is when the sprayer is outside a prescription boundary and the Rate outside polygon option is zero The operator must ensure that the master switch is off when there is no field open so that no spray is accidentally applied to areas that shouldnt be sprayed for example roads paths and neighboring fields Once you select Raven as your controller the following screen appears on the display Output Port Port A Note Do not configure the display to output NMEA messages on the same port that your controller is connected to 84 CFX 750 Display User Guide Implement Application Controller 5 2 On the Raven controller configure the following Data Menu settings Item Setting Baud or Baud Rate 9600 GPS Inac DLOG or Data Log On TRIG or Data Log Trigger Value 1 UNITor Data Log Trigger Units sec Note In the GPS group if Send time Time acknowledge or Close file appear change them to GPS Inac Otherwise the DLOG or DAT
30. roll offset This takes approximately 20 seconds Angle Per Turn calibration Note Make sure that you have set the IMD 600 orientation and performed the T3 terrain compensation calibration first Note Make sure that you are operating the vehicle in an open field with ample area for the vehicle to make right and left turns 1 Tap Right Angle Per Turn Calibration 2 Drive forward until appears and then tap the icon Note For the best results drive the vehicle between 2 and 4 mph 3 Allow the system to operate for 20 seconds until you receive a message that the calibration is complete 4 Repeat Step 1 through Step 3 for left angle per turn calibration EZ Pilot system calibration In this step you must drive and engage on a straight AB line in a clear field 1 Begin driving and tap A 2 Drive 160 feet and then tap B CFX 750 Display User Guide 61 4 4 Vehicle A series of calibration screens will allow you to adjust any settings as necessary Operation You must calibrate and set up the EZ Pilot system before operation Note Do not operate the EZ Pilot system while driving in reverse gear Engaging the system Before you can engage the EZ Pilot system you must e open a field in the guidance screen e define an AB line e position the vehicle within the configured engage limits To engage the system 1 Point the nose of the vehicle toward the guidance line and drive at operational speed 2 From the gu
31. spraying e Red The section is off the switch is off Target rate If a prescription is loaded P displays to indicate that the prescription rate is being used rather than the target rate O Actual rate The actual application rate This is the amount of product that is currently being applied Application indicator The wheel on the display spins when the Raven master switch is on and the booms are on Target Rate To manually enter a rate to send to the controller 1 Inthe Settings screen tap Implement and then Advanced 2 Tap Target Rate and then adjust the rate that is sent to the controller Automatic Boom Switching The CFX 750 display will not do automatic boom switching for the Raven controller Note To ensure that areas outside the headland in exclusion zones or previously sprayed areas are not sprayed you will need to manually turn off the Raven controller master switch 86 CFX 750 Display User Guide Implement Application Controller 5 Rawson controller Setup 1 Once you select Rawson as your controller a warning message appears Make sure that you read the message carefully and then tap 3 to continue The Output Port screen appears Output Port Port A 2 Change the Output Port to COM or AUX to match the port on the display that the controller is connected to 3 On the Rawson controller Verify the default target rate and step size and then enter these values into the CFX 750 display To
32. steering corrections occur at the correct point When you configure the system on a swather the Swather steering delay setting is available on the Vehicle Setup screen Some swathers have steering that is slow to react after the steering wheel is turned The system uses the steering delay setting to compensate for this slowness and ensure that steering corrections occur at the correct point To improve the performance of your swather adjust the Swather steering delay setting by a small amount 0 1 seconds at a time Test the result between each adjustment After using the EZ Pilot system e Before you leave the vehicle turn off the power to the display which will turn off the EZ Pilot system power e Iftransporting the vehicle between fields or using public roadways the red EZ Pilot system override switch must be in the off down position CFX 750 Display User Guide Vehicle 4 The Autopilot automated steering system Note For advanced setup options contact your Trimble reseller Setup To view and adjust settings for the Autopilot system Fa 1 Inthe guidance screen tap AT and then tap Vehicle 2 Tap Auto Steer and then Autopilot Configuration n Auto Steer System Autepilet d Type j Note lf the Autopilot Configuration button does not appear tap Auto Steer System Type and then select Autopilot for your controller From the Autopilot Configuration screen you can view and adjust the settings for e Online Aggr
33. switch or relay for equipment that should be active when engaged CFX 750 Display User Guide 143 9 System Enable Advanced User Config A N CAUTION Do not use the Enable Advanced User Config feature unless you have the support of a Trimble Reseller Altering any of the settings for this feature may cause system failure NMEA Output NMEA National Marine Electronics Association messages are a standard format that GPS devices use to communicate The CFX 750 display can output NMEA messages to communicate with other NMEA compatible devices In the NMEA Port Parameters screen specify the following Use this setting To NMEA output port Specify the port that the NMEA device is connected to Baud Rate Set the transmit receive rate of the serial port in bits per second bps Data Parity Select how the parity bit is added to the data transfer Note For the CEX 750 display to communicate with another device the Port Parameters on the display must match those of the device In the Message Selection screen select from the list of available NMEA messages Message Description GGA Position and fix related data VTG Speed and heading GSA Position fix mode satellites used and the dilution of precision DOPs GLL Position and status RMC Status position speed over ground SOG date and magnetic variation of the position _ ZDA Date and time GSV Satellite information EZ Remote joystick The EZ Remote option will only appear
34. system features Advanced SavelLoad Configurations 3 Enable Advanced User ort a Config NMEA Output Save Load Configurations Once you have set up your lightbar for your current job you can save the settings to a configuration file Saving a system configuration can be useful for e Quick setup when moving the display between vehicles e Quick setup when using the same vehicle but changing the implement or application e Tuning the settings for improved performance Save your improved settings e Restoring known good settings if unwanted adjustments have been made Digital Output The CFX 750 display can generate a digital signal on pin 2 of Port A Note Additional equipment may be required to properly use the Digital Output function To use speed pulse output you need a radar sensor cable kit that includes a pulse amplifier adapter Contact your local reseller Use this setting To Disabled Disable digital output on pin 2 of Port A Radar Output simulated radar pulses at a pre defined speed pulse output rate This can be useful to e Replace the radar true ground speed sensor for speed on the vehicle e Send speed to any other agricultural device requiring speed pulses such as a yield monitor or variable rate controller Note After you select Radar set the radar frequency rate from the Digital Output screen Remote Output Output a signal whenever auto steering is engaged This can be useful to drive a
35. the mounting plate to the vehicle roof with the adhesive strips Ensure that the mounting plate is centered along the vehicle roof Connect the antenna cable to the antenna Place the antenna directly on the mounting plate The three magnets embedded in the bottom of the antenna will hold it in place Route the other end of the antenna cable into the cab CFX 750 Display User Guide 23 2 Installing the Display and Antenna 24 CFX 750 Display User Guide CHAPTER Getting Started Display basics This chapter describes in general terms how to The Quick Start Wizard use the CFX 750 display Using the setup wizards The guidance screen Using the EZ Remote joystick Reading lightbar patterns On screen icons CFX 750 Display User Guide 25 3 Getting Started Display basics The CFX 750 display provides guidance steering and precision agriculture functionality The display has a touchscreen that you use to operate your system and view guidance information In addition there is a USB port on the display for loading and saving field data Front view Mapping BOO PF ty Autosteer Setup A Se CFX 750 Item Description Notes 5 _ Touch sensitive screen To interact with the system tap the screen with your finger For more information see Recalibrate touchscreen page 148 OQ Speaker You can adjust the speaker volume or turn it off For more information see Touchscreen speaker volume page 142 O Integra
36. you also meet all ofthese conditions a The modified work must itself be a software library b You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change c You must cause the whole ofthe work to be licensed at no charge to all third parties under the terms of this License d If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility other than as an argument passed when the facility is invoked then you must make a good faith effort to ensure that in the event an application does not supply such function or table the facility still operates and performs whatever part ofits purpose remains meaningful For example a function in a library to compute square roots has a purpose that is entirely well defined independent of the application Therefore Subsection 2d requires that any application supplied function or table used by this function must be optional ifthe application does not supply it the square root function must still compute square roots These requirements apply to the modified work as a whole If identifiable sections of that work are not derived from the Library and can be reasonably considered independent and separate works in themselves then this License and its terms do not apply to those sections when you distribute them as separate works But when you distribute th
37. 50 display If the section switch is in the off down position the section s assigned to it are commanded to be off When the Automatic Manual section switch is in the Manual position If the section switch is in the on up position the section s assigned to it are commanded to be on This overrides the CFX 750 display and coverage logging is ignored If the section switch is in the off down position the section s assigned to it are commanded to be off This overrides the CFX 750 display and coverage logging is ignored The LED has the following status indicators Green The unit is powered and is communicating with the CFX 750 display Yellow The unit is initializing communications with the CFX 750 display Red The unit is powered but not communicating with the CFX 750 display 80 CFX 750 Display User Guide Implement Application Controller 5 HARDI 5500 controller Note For the HARDI 5500 controller to work correctly with the CFX 750 display you must install firmware version 3 16 or greater on the HARDI controller and connect a JOBCOM control box Setup 1 Once you select the HARDI 5500 as your controller the following screen appears on the display Output Port Port A Note Do not configure the display to output NMEA messages on the same port that your controller is connected to de 3 On the HARDI 5500 controller go to the Settings menu Change Remote to Enable For more information o
38. 542760 R 1234FOCFO3 Section Control Module is on the left 1234807838 123457D3A1 dl For each module the width of the section it will control Width of Left Rawson Control Module How wide la tha section of implement for this Rawson Control Module 74 CFX 750 Display User Guide Implement Application Controller 5 For Section Control a Where on your implement each module is located Hardware Location Left ke Using the serial mumbar indicate which Section Control Module is on the left gt al b For each module the number of sections it will control of Sections Left Section Module How many comitrol sections are attached to this Field I9 Section Control Module Note You must enter accurate values for the system to work properly 9 Once you have completed the wizard you can adjust your section widths if necessary Section Widths Edit settings by pressing each one individuality A Sectonwidthi ie Press the green accept button to cont nua y Section Width 2 ae d Section Width 3 nne y Section Width 4 une gt CFX 750 Display User Guide 75 5 Implement Application Controller Field 1Q Hydraulics Test A WARNING MOVING PARTS DURING THIS TEST Please stay clear of the implement Ensure the implement is raised the transmission is in PARK and the emergency brake is applied before continuing After the setup wizard is complete the display tests the hydraul
39. A LOG option will not appear For more information on configuring and calibrating the Raven controller refer to the Raven instruction manual Advanced Use the Advanced option in the Implement screen to configure the following e Boom Setup e Target Rate e Rate Snapping Boom Setup Use this option to view and adjust the following settings Setting Notes Implement width Enter a width between 1 00 328 01 0 30 99 99 m Number of sections Enter a number between 1 10 Target Rate Set the target application rate that will be sent to the Raven controller Enter a rate between 0 0 11000 0 Rate Snapping Due to pump constraints liquid flow is generally inconsistent To control how these inconsistencies appear on your display turn rate snapping on or off Setting Notes On Matches the applied rate to the target rate when within 10 of the value Off Shows all fluctuations in the actual applied rate CFX 750 Display User Guide 85 5 Implement Application Controller Operation When you connect the Raven controller to the CFX 750 display the following items appear on the guidance screen a Of OE K E W ny e Can t engage Too slow peo T 20 0 gal a A 0 0 gal a Ek ca oe Item Description Notes 1 Quick Access icon See Quick Access icon page 38 O Boom section status Shows the current state of each boom section indicators e Green Enabled and spraying e Gray Enabled but not currently
40. A messages on the same port that your controller is connected to 2 On the Bogballe controller press Return Return Fertil Distrib Select Type Bogballe E EX Accept For more information on setting up the Amazone controller refer to the Amazone instruction manual CFX 750 Display User Guide 99 5 Implement Application Controller Advanced Use the Advanced option in the Implement screen to configure the following e Boom Setup e Swath Control e Rate Control e Target Rate e Single Section Boom Switching Boom Setup Note The boom setup on the CEX 750 display must match the setup on the LH 5000 controller If the boom setup differs between the display and the LH 5000 controller a warning message appears on the display Use this option to view and adjust the following settings Setting Notes Implement width Enter a width between 1 00 328 01 0 30 99 99 m Fence Nozzles Enter the locations of any fence nozzles Number of sections Enter a number between 1 10 Swath Control Use this option to view and adjust the following settings Setting Notes Boom control Enter a width between 1 00 328 01 0 30 99 99 m Coverage switching overlap Control the amount of boom switching overlap allowed before the section will be switched by the system Enter a value between 1 99 Boundary switching overlap Control the amount of overlap on a boundary before the boom section is switched off
41. B B e 2 Item Description Notes 1 Quick Access icon See Quick Access icon page 38 2 Boom section status Shows the current state of each boom section indicators e Green Enabled and spraying e Gray Enabled but not currently spraying e Red The section is off the switch is off Target rate If a prescription is loaded P displays to indicate that the prescription rate is being used rather than the target rate O Actual rate The actual application rate This is the amount of product that is currently being applied Application indicator The wheel on the display spins when the LH 5000 master switch is on and the lightbar receives flow messages from the controller 96 CFX 750 Display User Guide Implement Application Controller 5 Vaderstad Setup l Once you select Amazone as your controller the following screen appears on the display Output Port Port A Note Do not configure the display to output NMEA messages on the same port that your controller is connected to 2 Inthe Device Type screen select the type of implement you are using Sprayer Planter Seeder Fertilizer Spreader 3 On the Vaderstad controller go to the setup screen 4 Set GPS to No Advanced Use the Advanced option in the Implement screen to configure the following Boom Setup Swath Control Rate Control Target Rate Single section boom switching Rate Snapping CFX 750 Display User Guide 97 5 Implement Ap
42. Back view page 27 Use the USB socket to manage your data via a USB drive 30 CFX 750 Display User Guide Getting Started 3 USB drive compatibility You can use the following USB drives with the CFX 750 display e A Data micro SDHC SD USB adapter e ADATA Classic C801 8GB e Digital Concepts USB to PC Reader e Generic USB UDHC adapter with Transcend 8GB microSDHC card e Kingston Data Traveler 8 GB e Kingston Data Traveler 101 e Lexar Firefly 1 GB e Lexar JumpDrive TwistTurn e Lexar Secure II Plus e PNY Attache e PNY Micro Swivel Attache 4GB e PNY Mini Attache 4 GB e PNY Mini Attache 8 GB e SanDisk Cruzer e SanDisk Cruzer Gator 4GB e SanDisk Cruzer Micro 1GB e Toshiba TransMemory U2M 004GTA 4GB e Transcend JetFlash Inserting a USB drive 1 Rotate the display so you that can see the back of it 2 Insert the USB drive into the USB socket When the USB drive is properly inserted the USB icon appears on the guidance screen Drive 160 ft to set B point The color of the USB icon indicates the current state of the USB drive Green the USB drive is connected Yellow the USB drive is connecting Red the connection to the USB drive has been lost Removing a USB drive A N CAUTION Do not remove the USB drive from the socket while the display is writing to or from the drive This will corrupt the data CFX 750 Display User Guide 31 3 Getting Started 1 Rotate the display so that you can see the back of it 2
43. E ER beg ER RT R KEN aus 91 DCD AA 91 e A oe eee Stee eee bee aah eee ee oee tad 91 Opera E pence teh tans a eee eee aes eae eee ee ee 93 EH DOUNCOMTOUCT 44 4 e44e54 5 ee PNG Pde he Pee a ee ee e hee he eee 93 DCMU AGG E ed eee ene ees Bae ae ee eta eee ee 93 TONG NC A ee ee ee es ee ee 94 J DCTANONy 4 4 ao e Sod oh ba ae yo eee ee ee a ee A 96 10 CFX 750 Display User Guide Contents Nerea AE rn eee eee ee ee eee G eae 97 ee A A AAA 97 o 4 gee ed pa pha eee eed eee eee be ean Goes eee oon G ees es 97 Single section boom switching ooo ooo 99 Bosbale CONTO e eppsaa ds aser a A esas 99 AAA 99 ACQUANCC O 44 posos raras arar asadas Aa 100 Single section boom switching 4 eee anh we es nan A AA Ee ee 101 Checking the implement connection 256649244444 48 455 5444440846004 2a 101 Mapping and Guidance xs s s s s e e 103 IMPOCUCHOM E rasa eae aioe dae eee ee toe E 104 Configuring the Guidance settings 2 ee 104 MIDIS T E shat e resonar ees eae es awe eee e 105 COVEerado DELI 46 5 oe BG eae eee a he eee Oe ee Lee ey ee ae A 105 pora a be ee eect ee Sete eee set ake eeee eset eeeee eee setae 106 MapDINS es cora ere eee ene eee tet eee ee wee ee eae eee Bea aa es 106 Freelorm ReCOMdINe e eseas tiag imina tania 107 Headland Infill Switching 4 2204 toe he 8 poke ke Ge oe Be nissan 107 os A peewee eke enG see eee nee ee eo eee ee ee Se 107 Sa Ee L ooo ees epee ee ees Fe ea eee eee ee bee eye ee ee ee 108 Im
44. EN INVOLVED IN ITS CREATION PRODUCTION INSTALLATION OR DISTRIBUTION INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TITLE AND NONINFRINGEMENT THE STATED EXPRESS WARRANTIES ARE IN LIEU OF ALL OBLIGATIONS OR LIABILITIES ON THE PART OF TRIMBLE ARISING OUT OF OR IN CONNECTION WITH ANY PRODUCTS OR SOFTWARE BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW LIMITATIONS ON DURATION OR THE EXCLUSION OF AN IMPLIED WARRANTY THE ABOVE LIMITATION MAY NOT APPLY OR FULLY APPLY TO YOU NOTICE REGARDING PRODUCTS EQUIPPED WITH TECHNOLOGY CAPABLE OF TRACKING SATELLITE SIGNALS FROM SATELLITE BASED AUGMENTATION SYSTEMS SBAS WAAS EGNOS AND MSAS OMNISTAR GPS MODERNIZED GPS OR GLONASS SATELLITES OR FROM IALA BEACON SOURCES TRIMBLE IS NOT RESPONSIBLE FOR THE OPERATION OR FAILURE OF OPERATION OF ANY SATELLITE BASED POSITIONING SYSTEM OR THE AVAILABILITY OF ANY SATELLITE BASED POSITIONING SIGNALS Limitation of Liability TRIMBLES ENTIRE LIABILITY UNDER ANY PROVISION HEREIN SHALL BE LIMITED TO THE AMOUNT PAID BY YOU FOR THE PRODUCT OR SOFTWARE LICENSE TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW IN NO EVENT SHALL TRIMBLE OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES WHATSOEVER UNDER ANY CIRCUMSTANCE OR LEGAL THEORY RELATING IN ANY WAY TO THE PRODUCTS SOFTWARE AND ACCOMPANYING DOCUMENTATION AND MATERIALS INCLUDING WITHOUT LIMITATION DAMA
45. FX 750 power cable 77282 e CFX 750 basic power cable 67258 01 O 8 m GPS TNC TNC RT angle cable 50449 O AG25 GNSS antenna 77038 CFX 750 Display User Guide 21 2 Installing the Display and Antenna Standalone CFX 750 RTK corrections Connecting a standalone CFX 750 display to use RTK corrections Item Description 1 CFX 750 display Note RTK password required CFX 750 power cable CFX 750 basic power cable 8 m GPS TNC TNC RT angle cable AG25 GNSS antenna NMO to TNC 20ft antenna cable and base 00 0 00 900 MHz radio antenna kit Installing the antenna Trimble part number 94110 00 77282 67258 01 50449 77038 62120 22882 10 Note To minimize any interference to the GPS signal make sure that the GPS antenna is at least 1 m 3 ft from any other antenna including a radio antenna You may experience interference if you operate the vehicle within 100 m 300 ft of any power line radar dish or cell phone tower Note The AG25 antenna has integrated magnets for easy installation To attach the antenna to a non metal surface you must use the mounting plate 22 CFX 750 Display User Guide Installing the Display and Antenna 2 To install the AG25 antenna Find the mounting location for the antenna at the front of the vehicle roof centered from left to right On the mounting plate remove the protective covers from the adhesive strips Attach
46. GES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION LOSS OF BUSINESS INFORMATION OR ANY OTHER PECUNIARY LOSS REGARDLESS WHETHER TRIMBLE HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH LOSS AND REGARDLESS OF THE COURSE OF DEALING WHICH DEVELOPS OR HAS DEVELOPED BETWEEN YOU AND TRIMBLE BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES THE ABOVE LIMITATION MAY NOT APPLY OR FULLY APPLY TO YOU 4 CFX 750 Display User Guide PLEASE NOTE THE ABOVE TRIMBLE LIMITED WARRANTY PROVISIONS WILL NOT APPLY TO PRODUCTS PURCHASED IN THOSE JURISDICTIONS E G MEMBER STATES OF THE EUROPEAN ECONOMIC AREA IN WHICH PRODUCT WARRANTIES ARE THE RESPONSIBILITY OF THE LOCAL DEALER FROM WHOM THE PRODUCTS ARE ACQUIRED IN SUCH A CASE PLEASE CONTACT YOUR TRIMBLE DEALER FOR APPLICABLE WARRANTY INFORMATION Official Language THE OFFICIAL LANGUAGE OF THESE TERMS AND CONDITIONS IS ENGLISH IN THE EVENT OF A CONFLICT BETWEEN ENGLISH AND OTHER LANGUAGE VERSIONS THE ENGLISH LANGUAGE SHALL CONTROL Registration TO RECEIVE INFORMATION REGARDING UPDATES AND NEW PRODUCTS PLEASE CONTACT YOUR LOCAL DEALER OR VISIT THE TRIMBLE WEBSITE AT www trimble com register UPON REGISTRATION YOU MAY SELECT THE NEWSLETTER UPGRADE OR NEW PRODUCT INFORMATION YOU DESIRE Notices This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15
47. Offline distance CFX 750 Display User Guide 63 4 Vehicle Vehicle specific performance Before you use the EZ Pilot system consider the following performance suggestions Performance hint With tractors that have SuperSteer for example New Holland TG if the tractor has a SuperSteer front axle for best performance Reduce the Online Aggressiveness value Line up close to the swath and make certain that the front wheels are straight before engaging the EZ Pilot system To get smoother performance when the vehicle is pulling an implement over tilled ground enable the Diff Lock This prevents the machine from pulling sharply to the left or right If you are calibrating on a hard surface turn off Diff Lock The EZ Pilot system can be installed on Case IH STX tractors with Accusteer For optimal performance disable Accusteer using the switch in the cab if possible Vehicle type 2WD tractor O L L AWD tractor Sprayer L L L Swather e 64 It is common for these vehicles to have slow steering To compensate for this use high aggressiveness If you experience large slow oscillations increase the aggressiveness When you configure the system on a sprayer the Sprayer steering delay setting is available on the Vehicle Setup screen Some sprayers have steering that is slow to react after you turn the steering wheel The system uses the steering delay setting to compensate for this slowness and ensure that
48. To unlock features you must have an unlock code To obtain an unlock code contact your Trimble reseller l Ze Status In the Unlock Upgrade screen tap Password Upgrade Enter the unlock password Note that passwords are case sensitive Once the password is successfully entered the display automatically restarts Do not disconnect the power from the display while it is rebooting Use the Status screen to view the current status of the system The items that appear in the Status screen vary according to the features that you use Select this item To view Region protect The GPS signal region you are currently in and whether it is locked or unlocked If your region is locked contact your Trimble reseller Language Pack status The language packs that have been installed on the display LB25 remote lightbar status The following information for the lightbar e Status Connected or Disconnected e Serial number e Firmware version CFX 750 Display User Guide 147 9 System Select this item To view EZ Remote status The following information for the EZ Remote e Status Connected or Disconnected e Serial number e Firmware version System status The current time and date ID CFX 750 The following data about your CFX 750 display eVersion and Version date eSerial number ePart number eHarware Revision System voltage Temperature Storage This is the number of hours of coverage logging remaining before the
49. USER GUIDE CFX 750 Display Version 1 9 Revision A September 2011 Trimble Agriculture Business Area Trimble Navigation Limited Trimble Agriculture Division 10355 Westmoor Drive Suite 100 Westminster CO 80021 USA trimble_support trimble com www trimble com Legal Notices Copyright and Trademarks 2010 2011 Trimble Navigation Limited All rights reserved Trimble the Globe amp Triangle logo AgGPS EZ Boom EZ Guide EZ Steer Fmx and Tru Count are trademarks of Trimble Navigation Limited registered in the United States and in other countries Autopilot Autoseed AutoSense CFX 750 EZ Office FieldManager Field IQ FreeForm VRS VRS Now T2 Tru Application Control TrueGuide and TrueTracker are trademarks of Trimble Navigation Limited GreenSeeker is a registered trademark of NTech Ltd For STL support the software uses the Moscow Center for SPARC Technology adaptation of the SGI Standard Template Library Copyright 1994 Hewlett Packard Company Copyright 1996 97 Silicon Graphics Computer Systems Inc Copyright 1997 Moscow Center for SPARC Technology Microsoft Windows ActiveX Excel and Internet Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and or other countries Portions Copyright c 2009 Nokia Corporation and or its subsidiary ies Portions Copyright c 2003 Bitstream Inc All other trademarks are the property of th
50. a Manage Data Connected Farm Send Data Send Data Use the Client Farm Field and Event options to select an individual field or all events farms or fields for a client Send Fields to Connected Farm E press the green arrow button to send the selected Miles to the Cornected Farm y Cient Petersa mekatet is k a Farm Daiei x E Receiving Field data through the Connected Farm service With the Connected Farm service you can wirelessly transfer field information from the office to the CFX 750 display Field data includes field boundaries guidance lines prescriptions area features line features and point features To receive data from the Connected Farm service L Select the Wrench icon and then select Data Manage Data Connected Farm Retrieve Data From the Retrieve Data screen tap Check Server to check for and download new field data from the Connected Farm server CFX 750 Display User Guide 135 8 Data 3 Once the data is downloaded select the Get Fields from Connected Farm option to import the data into the display As new data is received use the Get Fields from Connected Farm function to import the most recent data into the display Retrieve Data The Connected Farm service adds a status icon to the Run screen that shows the status of Connected Farm operation An icon at the top right of the screen shows if field data is being sent or received When data is being sent or receiv
51. age logging when the auto steer system is engaged Use a remote switch to turn coverage logging on or off Description When enabled the display clears the nudged position each time you change swaths When enabled any applied nudge is cleared and all swaths return to their Original positions Each nudge moves the guidance line by this value The default nudge increment is 0 1 2 5 cm Enter a value between 2 12 3 30 cm Use this setting to set warning distance and recording positions for the following features Mapping e Point e Line e Area Warning distance You can set a warning distance so that the CFX 750 display alerts you when your machine approaches a feature As the machine moves to within the specified distance a warning screen appears on the display If you have an EZ Steer or Autopilot system with a sonalert connected an audible alarm also sounds You can set the warning distance to between 0 00 984 03 0 0 300 0 m Recording position Choose the point at which a feature is recorded When your vehicle is at this point the feature will be recorded 106 CFX 750 Display User Guide Mapping and Guidance 6 Delete features Use this function to delete point line and area features from a selected field Note that this function deletes only the features not the field itself FreeForm Recording Use this setting to choose how the display records a FreeForm pattern Select this mode To
52. and Trailing view icons e Panning Mode To e change the view tap A and then select the option that you require e exit a view and return to the guidance screen tap ES To learn how to change the View settings see View page 141 Zooming To zoom in or out on the guidance screen tap either A or Viewing modes There are two viewing modes Overhead and Trailing By default the view switches from Overhead to Trailing when you approach the AB line To access the Overhead view tap G l Mapping USB drive connected 36 CFX 750 Display User Guide Getting Started To access the Trailing view tap rey Happing Extended icons The guidance screen features several extended icons that are hidden in the default view To access or hide the extended icons tap or lt lt The following images show how the extended icons appear on the guidance screen when they are expanded and collapsed En 2 0 09 lt 00 SOT Status lt K E Settings Quick Access Quick Access Expanded Collapsed CFX 750 Display User Guide 3 37 3 Getting Started Quick Access icon You can use the Quick Access icon to quickly adjust common settings The items that appear in the Quick Access menu will vary depending on the AD applications that you are currently running Quick The following sections describe the items that may appear Access Note The Quick Access icon only appears when you are running Field
53. area or out of a sprayed area Enter a distance between 0 00 32 10 0 00 10 00 m 94 CFX 750 Display User Guide Implement Application Controller 5 Rate control Use this option to view and adjust the following settings Setting Notes On Application rates are sent from a prescription loaded in the display or the target rate manually configured on the display Off The target rate must be set on the LH 5000 controller The CFX 750 display does not send target rates to the controller This is the default setting Note When sending a target rate to the LH 5000 controller that is higher than 99 9 the display rounds to the nearest whole number For example 0 99 9 is not rounded 101 4 is rounded to 101 Target Rate Set the target application rate that will be sent to the LH 5000 controller Enter a rate between 0 0 11000 0 Turn Off Rate on Overlap Use this option to view and adjust the following settings Setting Notes Yes Does not spray over an area that has been previously sprayed No Sprays over an area that has been previously sprayed CFX 750 Display User Guide 95 5 Implement Application Controller Operation When the LH 5000 variable rate controller is connected to the display the following items appear on the CFX 750 displays guidance screen Em lt O OE 0 0 mph Es O lt gt Fleld L s W Sicllings Guidance A y ni e L Can t engage Too slow agpo T 20 0 gal a A 0 0 gal a
54. brary uses material from a header file that is part of the Library the object code for the work may be a derivative work of the Library even though the source code is not Whether this is true is especially significant if the work can be linked without the Library or if the work is itself a library The threshold for this to be true is not precisely defined by law If such an object file uses only numerical parameters data structure layouts and accessors and small macros and small inline functions ten lines or less in length then the use of the object file is unrestricted regardless of whether it is legally a derivative work Executables containing this object code plus portions of the Library will still fall under Section 6 Otherwise if the work is a derivative of the Library you may distribute the object code for the work under the terms of Section 6 Any executables containing that work also fall under Section 6 whether or not they are linked directly with the Library itself 6 As an exception to the Sections above you may also combine or link a work that uses the Library with the Library to produce a work containing portions of the Library and distribute that work under terms of your choice provided that the terms permit modification of the work for the customer s own use and reverse engineering for debugging such modifications You must give prominent notice with each copy of the work that the Library is used in it an
55. c to Manual mode while traveling Master switch e A Jump start top position The sections and rate are ready to be commanded by the CFX 750 display and the system is overridden to use a preset control speed the speed is set in the Setup screen Override tab X Tip Use the jump start function if you lose a GPS signal or you want to start applying before your implement is up to speed e B On middle position The sections and rate are ready to be commanded by the CFX 750 display e C Off lower position Sections are closed and rate is set to zero Note All systems must have a Field IQ master switch box CFX 750 Display User Guide 79 5 Implement Application Controller Field IQ 12 section switch box Note The 12 section switch box is required for section control For rate control only the switch box is optional Only one section switch box can be used on each system Each section switch is automatically assigned to the corresponding module The modules are read from left to right For example switch 1 assigns to the module furthest on the left when standing behind the implement The section switches have different functions depending upon the status of the master Automatic Manual section switch on the master switch box When the Automatic Manual section switch is in the Automatic position Ifthe section switch is in the on up position the section s assigned to it are commanded automatically by the CFX 7
56. ccess all of the available Controller Type options apart from None and Field IQ you must have a VRA unlock code To obtain a VRA unlock code contact your Trimble reseller 2 Select the controller that you are using Note When you change the controller type any open field will close 3 Configure your controller For more information see the following sections Field IQ page 70 HARDI 5500 controller page 81 Raven controllers page 84 68 CFX 750 Display User Guide Implement Application Controller 5 Rawson controller page 87 Amazone controller page 91 LH 5000 controller page 93 Prescriptions The CFX 750 display can use a prescription file to determine the rate of application in different areas of the field The prescription file consists of three separate ESRI files shp dbf and shx Each of these files contain different attribute information that the display uses You must load a prescription from the USB drive to the internal memory of the CFX 750 display The display cannot read prescriptions directly from a USB drive For more information see the section below Loading a prescription 1 Copy the prescription file from your computer to the AgGPS Prescriptions folder on your USB drive Note If you do not have an AgGPS directory on your USB create one by exporting field data to the USB For more information see Sending data to the USB drive page 137 2 Insert the USB drive into the USB s
57. cklight You can adjust the brightness of the screen backlight to maximize visibility and reduce glare in different light conditions For more information see Color Scheme page 141 Touchscreen speaker volume You can adjust the volume of the speaker according to your preference Choose from Loud Quiet or Off Lightbar Setup You can adjust the lightbar settings as follows Use this setting To Look Ahead Allow time for large vehicles to correct offline error e For large vehicles that take longer to turn increase the look ahead time e For 4WD articulated tractors always set the look ahead time to 0 seconds Look ahead time applies to LED guidance only and does not affect EZ Steer performance Set the look ahead time in seconds LED Spacing Adjust the sensitivity of the LEDs To Note The LED spacing increase sensitivity decrease the LED spacing is the distance decrease sensitivity increase the LED spacing represented by one LED LED Brightness Adjust the LED brightness for maximum visibility Main Lightbar LED Mode Select the required LED mode There are two modes to choose from e Chase Chase the lights to stay online The lights represent the swath location relative to the vehicle e Pull Center the lights to stay online The lights represent the vehicle location relative to the swath 142 CFX 750 Display User Guide System 9 Advanced Use the items in the Advanced screen to view and adjust advanced
58. commercially available and for which it does not charge separately subject to the procedures for delivery to purchasers of Trimble products generally If you have purchased the Product from an authorized Trimble dealer rather than from Trimble directly Trimble may at its option forward the software Fix to the Trimble dealer for final distribution to you Minor Updates Major Upgrades new products or substantially new software releases as identified by Trimble are expressly excluded from this update process and limited warranty Receipt of software Fixes or other enhancements shall not serve to extend the limited warranty period For purposes of this warranty the following definitions shall apply 1 Fix es means an error correction or other update created to fix a previous software version that does not substantially conform to its Trimble specifications 2 Minor Update occurs when enhancements are made to current features in a software program and 3 Major Upgrade occurs when significant new features are added to software or when a new product containing new features replaces the further development of a current product line Trimble reserves the right to determine in its sole discretion what constitutes a Fix Minor Update or Major Upgrade This Trimble software contains Qt 4 5 libraries licensed under the GNU Lesser General Public License LGPL The source is available from http qt nokia com downloads A copy o
59. ctions occur at the correct point Swather e When you configure the system on a swather the Swather steering delay setting is available on the Vehicle Setup screen e Some swathers have steering that is slow to react after the steering wheel is turned The system uses the steering delay setting to compensate for this slowness and ensure that steering corrections occur at the correct point e To improve the performance of your swather adjust the Swather steering delay setting by a small amount 0 1 seconds at a time Test the result between each adjustment After using the EZ Steer system e Any time that you are not using the EZ Steer system pivot the EZ Steer motor away from the steering wheel e Before you leave the vehicle turn off the EZ Steer system power switch or remove the power plug 56 CFX 750 Display User Guide Vehicle 4 The EZ Pilot assisted steering system The EZ Pilot assisted steering system works with the CFX 750 display s internal GPS receiver to provide vehicle guidance As such you must complete the GPS setup before you calibrate set up or run your EZ Pilot system See Chapter 7 GPS Setup To view and adjust the settings for the EZ Pilot system 1 Inthe guidance screen tap H and then tap Vehicle 2 Tap Auto Steer and then EZ Pllot Setup K Auto Steer System a Type LE EZ Pllot Setup Note If the EZ Pilot Setup button does not appear tap Auto Steer System Type and then select EZ Pilot f
60. d that the Library and its use are covered by this License You must supply a copy of this License If the work during execution displays copyright notices you must include the copyright notice for the Library among them as well as a reference directing the user to the copy of this License Also you must do one of these things a Accompany the work with the complete corresponding machine readable source code for the Library including whatever changes were used in the work which must be distributed under Sections 1 and 2 above and if the work is an executable linked with the Library with the complete machine readable work that uses the Library as object code and or source code so that the user can modify the Library and then relink to produce a modified executable containing the modified Library It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions b Use a suitable shared library mechanism for linking with the Library A suitable mechanism is one that 1 uses at run time a copy of the library already present on the users computer system rather than copying library functions into the executable and 2 will operate properly with a modified version of the library ifthe user installs one as long as the modified version is interface compatible with the version that the work was made with c Accompany t
61. dvanced filter technology CFX 750 Display User Guide 125 7 GPS 126 CFX 750 Display User Guide CHAPTER Data In this chapter The CFX 750 display saves field data to the displays internal memory You can transfer this m Introduction data to your home or office computer through a m Connected Farm Setup USB drive or wirelessly through the Connected Farm server m Manage Data This chapter describes how to manage the data generated by the CFX 750 display CFX 750 Display User Guide 127 8 Data Introduction Use the options in the Data menu to Save and retrieve fields from the USB drive Send fields via Connected Farm to your home or office PC Delete fields and coverage logging Export diagnostic log files to the USB drive for technical support purposes Copy prescriptions from the USB drive to the internal memory and delete from the internal memory To access the Data menu Fi 1 From the guidance screen tap HT 2 From the Settings screen select Data The following screen appears E aj lw gt DCM 300 modem This section describes how to set up a DCM 300 modem for use with VRS corrections Passcodes The DCM 300 modem requires a passcode upgrade to use VRS and Connected Farm functions VRS and Sync File Transfer functions in the DCM 300 modem must be unlocked to begin using VRS corrections or transferring data 128 CFX 750 Display User Guide Data To unlock the
62. e Chase the vehicle is offline to the right e Pull the vehicle is offline to the left Using the EZ Remote joystick Optionally you can use an EZ Remote joystick to control the CFX 750 display The joystick has ten LED buttons six have preset functions you can assign one of the following functions to each of the other four e Map arock tree or weed e Start or finish a line e Start or finish an area e Start or finish an exclusion zone e Turn coverage on or off e Camera A or Camera B control e Show trailing map view e Show overhead map view e Zoom e Show status To learn how to assign a function to a programmable button see EZ Remote joystick page 144 42 CFX 750 Display User Guide Getting Started 3 On screen icons The tables in this section describe all of the icons available on the CFX 750 display Note Icons appear only when they are appropriate They are not visible at all times To activate an icon tap it with your finger If the display does not respond when you tap it see Recalibrate touchscreen page 148 System icons Data configuration Settings Configuration Accept save changes Information icons Description Description Setup complete General alert Critical warning Information CFX 750 Display User Guide 43 3 Getting Started View icons eon Description Activate external video input Pan view Full screen external video Zoom in Run screen trailing view Zoom out
63. e following 1 Configure how the guidance displays on your screen See Configuring the Guidance settings below 2 Seta guidance line See Guidance lines page 112 3 Configure the lightbar See Lightbar Setup page 142 Configuring the Guidance settings To configure your Guidance settings 1 From the guidance screen tap P l 2 From the Settings screen tap Guidance Guidance 7 S Turn Settings O Coverage Settings b y iii Autisma 3 Select the options that you would like to configure Option To learn more see Turn Settings page 105 Coverage Settings page 105 Nudge Settings page 106 Mapping page 106 FreeForm Recording page 107 Headland Infill Switching page 107 Boundary Setup page 107 104 CFX 750 Display User Guide Mapping and Guidance 6 Turn Settings The available Turn Settings are described below Minimum turn radius mode This setting smoothes corners on curved AB lines which optimizes the accuracy of your auto steer system when steering curves Use this mode To Automatic Set the radius to 80 of the swath width or 32 8 10 m whichever is larger This is the default mode Disabled Manual No attempt is made to keep the corners above a minimum turn radius Note If you use this mode curves may be very tight and the auto steering system may be unable to successfully complete the turn Manually choose the minimum radius Tight turn alert threshold The CFX 750 dis
64. e headland CFX 750 Display User Guide 117 6 Mapping and Guidance 3 Begin to drive the circuit of the headland Note To ensure straight sides on the headland you can use the pause feature See Creating straight sections on Headland or Curve swaths page 110 4 Tap A to set the A point of your guidance line If the internal pattern is an A line the line is set an AB Line continue to drive around the headland When you reach the other end of the internal guidance line tap to set the B point o When you have defined the internal pattern guidance line the start point circle appears around the start point ofthe headland Note If you return to the start of the headland before you define a guidance line the headland will not complete 5 To complete the headland do one of the following Note Define the master line for the internal pattern before you complete the headland Drive around the rest of the headland until you return to the start point circle When you drive into the start point circle the headland completes automatically Drive part of the headland and then tap O The headland completes with a straight line from the vehicle position back to the start point Once you have completed the headland the headland guidance line appears When the vehicle moves out of the headland and into the interior of the pattern the interior is populated with your selected the guidance line pattern straight AB or
65. e same sections as part of a whole which is a work based on the Library the distribution of the whole must be on the terms of this License whose permissions for other licensees extend to the entire whole and thus to each and every part regardless of who wrote it Thus it is not the intent of this section to claim rights or contest your rights to work written entirely by you rather the intent is to exercise the right to control the distribution of derivative or collective works based on the Library In addition mere aggregation of another work not based on the Library with the Library or with a work based on the Library on a volume of a storage or distribution medium does not bring the other work under the scope of this License 3 You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library To do this you must alter all the notices that refer to this License so that they refer to the ordinary GNU General Public License version 2 instead of to this License If a newer version than version 2 of the ordinary GNU General Public License has appeared then you can specify that version instead if you wish Do not make any other change in these notices Once this change is made in a given copy it is irreversible for that copy so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy This option is useful when
66. e you are driving to finish coverage logging tap d iih gt Note There may be a delay between the time you start or stop coverage logging onscreen and the time the implement actually starts or stops coverage To compensate for this you can add a time delay to the drawing of coverage logging See Coverage on off delay page 105 Note Field coverage is limited to 1000 acres for each event The pause resume function When you tap Pause an icon appears on the screen to show your exact location when the guidance was paused This enables you to return to that position in the field When you pause guidance e Your current position relative to the pause icon appears in the status bar at the top of the screen e The guidance line that you were on is displayed even if you drive onto another swath e The pause resume icon remembers the vehicle position even when the lightbar is turned off Curve smoothing 120 By default the CFX 750 display smooths curves for improved guidance and auto steering You can disable curve smoothing on tight turns curves that have a radius of less than 3m 10 ft Note If you disable curve smoothing the CFX 750 display or the Autopilot system may not be able to auto steer around the tighter turns Be careful when you disable curve smoothing To disable curve smoothing 1 Inthe Settings screen tap Guidance and then tap Turn Settings 2 Tap Minimum Turn Radius Mode and then select Automatic
67. ed an orange arrow blinks between the tractor and office computer ive 160 fe to mal B Seine Manage Data The Manage Data screen enables you to handle your data through the USB drive or the displays internal memory USB The USB screen enables you to e Retrieve the field data and CFX 750 configuration files from a USB drive and transfer it to the internal memory The field data includes Field Boundaries Point Line and Area features Guidance lines Event data coverage 136 CFX 750 Display User Guide Data 8 Prescriptions e Send the following data from the internal memory to the USB drive Autopilot information Prescriptions a Client farm and field data Retrieving data from the USB drive To transfer data from the USB drive to the internal memory 1 Inthe Manage Data screen tap USB 2 Tap Retrieve Data and then choose the data that you would like to retrieve Sending data to the USB drive To transfer data from the internal memory to the USB drive 1 Inthe Manage Data screen tap USB 2 Tap Send Data to USB and then choose the data that you would like to send Send Fields to USB Prasa tha green arrow button to pend the selected files to the USS drive Note You cannot send data to a USB drive that is over 90 full For more information see The USB socket page 30 Clearing the internal memory Over time the CFX 750 displays internal memory may become full To avoid th
68. eir respective owners Release Notice This is the September 2011 release Revision A of the CFX 750 Display User Guide It applies to version 1 9 of the CFX 750 display software Legal Notices The following limited warranties give you specific legal rights You may have others which vary from state jurisdiction to state jurisdiction Product Limited Warranty Trimble warrants that this Trimble product and its internal components the Product shall be free from defects in materials and workmanship and will substantially conform to Trimbles applicable published specifications for the Product for a period of two 2 years starting from the earlier of i the date of installation or ii six 6 months from the date of original Product shipment from Trimble This warranty applies only to the Product if installed by Trimble or a dealer authorized by Trimble to perform Product installation services Software Components All Product software components sometimes hereinafter also referred to as Software are licensed solely for use as an integral part of the Product and are not sold Any software accompanied by a separate end user license agreement EULA shall be governed by the terms conditions restrictions and limited warranty terms of such EULA notwithstanding the preceding paragraph During the limited warranty period you will be entitled to receive such Fixes to the Product software that Trimble releases and makes
69. elbase Antenna height Antenna to axle offset Freeplay left right Motor speed Notes Enter the type of vehicle on which the EZ Pilot system will be installed See Entering vehicle measurements page 59 See Entering vehicle measurements page 59 See Entering vehicle measurements page 59 Drives consistently to one side of the line e If the vehicle is offline to the left increase the Freeplay offset to the right e If the vehicle is offline to the right increase the Freeplay offset to the left Control the speed of the EZ Pilot drive wheel motor Aggressiveness Use this option to view and adjust the settings described below Setting Online aggressiveness Approach aggressiveness Notes Control how aggressively the EZ Pilot system corrects deviations from the guidance line Enter a value between 50 150 Control how fast the EZ Pilot system steers the vehicle onto the guidance line Enter a value between 50 150 58 CFX 750 Display User Guide Vehicle 4 Vehicle Calibration Menu See Angle Per Turn calibration page 61 Calibration Before you begin to use the display you must calibrate the EZ Pilot system To do this complete the Quick Start Wizard see The Quick Start Wizard page 32 that appears the first time that you use the display To calibrate the EZ Pilot system at a later time complete the following process 1 Inthe guidance screen tap A and then tap Vehicle 2 Tap A
70. entering VRS settings provided by your Trimble CenterPoint or Network RTK provider The required settings are as follows Server Address Internet base settings Description Server Name Address RTK VRS CORS base station broadcast name Server Port Number Server Port Number Mount Point Base station mount point VRS User Name Network Assigned username VRS Password Network Assigned password CFX 750 Display User Guide 131 8 Data Once the wizard is completed a screen shows the VRS connection status and details all the settings entered The VRS status message types are as follows Logged in 155 83 111 09 2170 Mount Paint TWH AG GNSS WAS Laer Harme WAS Password Device Mare DMH Serial Humber 5051593079 Firmware Version LLO VRS connection status Description Logged in VRS connected Mobile network No service Connected Farm Setup When you enable the Connected Farm feature this allows the CFX 750 display to use the Connected Farm server to automatically and wirelessly send field information to your home computer Initial setup The Initial Setup wizard takes you through the process of setting up your wireless modem and registering the network By default the Connected Farm feature is set to Off To turn the feature on 1 Tap Connected Farm Setup and then Connected Farm 2 Select On The Connected Farm Setup screen appears Connected Farm Setup E Seings j Note When you turn the C
71. erage Sections will turn on as soon as they move from a covered to an uncovered area e Less overlap Set a low percentage when you need to save product The system will turn off sections as soon as you reach any covered area This may leave some skips Sections will turn on when the entire section has moved from a covered to an uncovered area Refill method Choose from one of the following options e Refill to fill the tank or bin to the top e Partial Refill to add a specified amount to the tank or bin when you select Partial Refill Now from the Refill screen Refill Now Partial Refill Now Use this option to refill the tank or bin Boundary switching overlap Use this option to control the amount of overlap on a boundary before the system switches off the boom section Enter a percentage between 1 99 Note This setting only operates when the boom is overlapping a headland or pivot boundary or exclusion zone For e Less skip Set a high percentage when it is acceptable to apply outside the boundary e Less overlap Set a low percentage when you do not want to apply outside the boundary A very low setting may cause some skip at the boundary On off valve latency This option allows for hardware delays by adjusting the amount of time needed before turning the valves on or off To use this option 1 Measure the amount of time it takes in seconds for the system to reach the correct rate after you have switched it on
72. essiveness e Operator Alert Timeout e End of Row Warning Distance e NMEA Output See Chapter 7 GPS e Rave Vehicle Configuration File use a virtual keypad to save your current vehicle configuration Operation You must calibrate and set up the Autopilot automated steering system before operation Engaging the system Before you can engage the Autopilot automated steering system you must e open a field in the guidance screen e define an AB line e position the vehicle within the configured engage limits To engage the system CFX 750 Display User Guide 65 4 Vehicle 1 Point the nose of the vehicle toward the guidance line and drive at operational speed 2 Doone of the following From the guidance screen tap Press the optional remote engage foot pedal Disengaging the system The Autopilot automated steering system automatically disengages when one of the following happens e The vehicle is outside the configured engage limits e You pause the system e GPS positions are lost e You tap the Engage button on the guidance screen You can manually disengage the system by turning the steering wheel this overrides the electric motor Check this setting before you start using the system by engaging on a line and then turning the wheel until the system disengages To adjust the amount of force required to disengage the system change the Override Sensitivity in the Engage Options screen Engage status indicators
73. f the LGPL license is included in the appendices of this manual and at ftp ftp trimble com pub open_source FmxX This software includes the DejaVu fonts which are licensed under the Bitstream Vera license terms available at http dejavu fonts org wiki index php title License and http www gnome org fonts GNU LESSER GENERAL PUBLIC LICENSE Version 2 1 February 1999 Copyright c 1991 1999 Free Software Foundation Inc 51 Franklin Street Fifth Floor Boston MA 02110 1301 2 CFX 750 Display User Guide USA Everyone is permitted to copy and distribute verbatim copies of this license document but changing it is not allowed This is the first released version of the Lesser GPL It also counts as the successor of the GNU Library Public License version 2 hence the version number 2 1 Preamble The licenses for most software are designed to take away your freedom to share and change it By contrast the GNU General Public Licenses are intended to guarantee your freedom to share and change free software to make sure the software is free for all its users This license the Lesser General Public License applies to some specially designated software packages typically libraries of the Free Software Foundation and other authors who decide to use it You can use it too but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case ba
74. faced maintained stored and operated in accordance with Trimble s relevant operator s manual and specifications and b the Products and Software are not modified or misused The preceding warranties shall not apply to and Trimble shall not be responsible for defects or performance problems resulting from i the combination or utilization of the Product or Software with hardware or software products information data systems interfaces or devices not made supplied or specified by Trimble ii the operation of the Product or Software under any specification other than or in addition to Trimble s standard specifications for its products iii the unauthorized installation modification or use of the Product or Software iv damage caused by accident lightning or other electrical discharge fresh or salt water immersion or spray outside of Product specifications or v normal wear and tear on consumable parts e g batteries Trimble does not warrant or guarantee the results obtained through the use of the Product or that software components will operate error free THE WARRANTIES ABOVE STATE TRIMBLE S ENTIRE LIABILITY AND YOUR EXCLUSIVE REMEDIES RELATING TO THE PRODUCTS AND SOFTWARE EXCEPT AS OTHERWISE EXPRESSLY PROVIDED HEREIN THE PRODUCTS SOFTWARE AND ACCOMPANYING DOCUMENTATION AND MATERIALS ARE PROVIDED AS IS AND WITHOUT EXPRESS OR IMPLIED WARRANTY OF ANY KIND BY EITHER TRIMBLE NAVIGATION LIMITED OR ANYONE WHO HAS BE
75. gage limits To engage the system 1 Point the nose of the vehicle toward the guidance line and drive at operational speed 2 Doone of the following From the guidance screen tap Press the optional remote engage foot pedal Disengaging the system The EZ Steer system automatically disengages when one of the following happens e The vehicle is outside the configured engage limits e You pause the system e GPS positions are lost e You tap the Engage button on the guidance screen You can manually disengage the EZ Steer system by turning the steering wheel this overrides the electric motor Check this setting before you start using the system by engaging on a line and then turning the wheel until the system disengages To adjust the amount of force required to disengage the system change the Override Sensitivity in the Engage Options screen 54 CFX 750 Display User Guide Vehicle 4 Engage status indicators Engage status Icon color Ready to engage O Engaged 6 Cannot engage Z Curve Auto steering Accuracy in Headlands It is possible to engage the EZ Steer system on headlands with sharp corners at the edge of the field However the EZ Steer system may be unable to drive around these sharp bends Use one of the following methods to compensate e Manually steer the vehicle around the corner Once you have rounded the corner re engage the EZ Steer system e Inthe Engage Options screen increase the Disengage Offli
76. getting in or out of the cab or any other activities 18 CFX 750 Display User Guide The image to the right shows the mounting assembly for the display Item Description O Diamond shaped mounting plate O RAM mount Bar mount To install the display Installing the Display and Antenna 1 Use the supplied screws to firmly attach the diamond shaped mounting plate to the back of the display CFX 750 Display User Guide 2 19 2 Installing the Display and Antenna FIRE 2 Attach the RAM mount to the ball on the diamond shaped mounting plate 3 Select a position in the cab for the display Hold the display in the selected location and check that it is easily accessible from the drivers seat 4 Use the provided bolts to attach the bar mount to the cab 5 Attach the other end of the RAM mount to the ball on the bar mount and then tighten the screw Connecting the display The diagrams in this section show how to setup the CFX 750 display as a standalone system To learn how to connect the CFX 750 display to other the system components see the CFX 750 Cabling Guide 20 CFX 750 Display User Guide Installing the Display and Antenna 2 Standalone CFX 750 WAAS EGNOS OmniSTAR XP HP corrections Connecting the CFX 750 display to use WAAS or XP HP corrections Es gt y O uy Item Description Trimble part number O CFX 750 display 94110 00 O C
77. he buttons on the EZ Remote joystick to perform the functions you have assigned 2 1 Left Right Trigger on back ii Engage Note The Up Down and Trigger buttons are not supported Use this button To Engage Engage auto steering Up Down N A Right Nudge the guidance line to the right in the guidance screen Left Nudge the guidance line to the left in the guidance screen Trigger N A 1 4 Activate the function that you have assigned To learn how to assign a function to the programmable button see the EZ Remote joystick page 144 146 CFX 750 Display User Guide System 9 Unlock Upgrade Use the Unlock Upgrade screen to Upgrade your CFX 750 display to a newer firmware version Unlock features such as Field IQ crop input control system Upgrading your display l 2 3 4 5 6 Transfer the new firmware file from www trimble com to your office computer Connect the CFX 750 display USB memory stick to your office computer Unzip the firmware file and then save it to the root folder ofthe USB memory stick Insert the USB memory stick into the USB socket of the display In the Unlock Upgrade screen tap Firmware Upgrade Wizard Select the file that you want to upload and then tap Cy The firmware begins to load Once the new firmware has successfully loaded the display automatically restarts Do not disconnect the power from the display while it is rebooting Unlocking features Note
78. he work with a written offer valid for at least three years to give the same user the materials specified in Subsection 6a above for a charge no more than the cost of performing this distribution d If distribution of the work is made by offering access to copy from a designated place offer equivalent access to copy the above specified materials from the same place e Verify that the user has already received a copy of these materials or that you have already sent this user a copy For an executable the required form of the work that uses the Library must include any data and utility programs needed for reproducing the executable from it However as a special exception the materials to be distributed need not include anything that is normally distributed in either source or binary form with the major components compiler kernel and so on of the operating system on which the executable runs unless that component itself accompanies the executable It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system Such a contradiction means you cannot use both them and the Library together in an executable that you distribute 7 You may place library facilities that are a work based on the Library side by side in a single library together with other library facilities not covered by this License and distribute such a combined library prov
79. here is no warranty for the free library Also if the library is modified by someone else and passed on the recipients should know that what they have is not the original version so that the original author s reputation will not be affected by problems that might be introduced by others Finally software patents pose a constant threat to the existence of any free program We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder Therefore we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license Most GNU software including some libraries is covered by the ordinary GNU General Public License This license the GNU Lesser General Public License applies to certain designated libraries and is quite different from the ordinary General Public License We use this license for certain libraries in order to permit linking those libraries into non free programs When a program is linked with a library whether statically or using a shared library the combination of the two is legally speaking a combined work a derivative of the original library The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom The Lesser General Public License permits more lax criteria for linking other code with the library
80. ics of your system During this test you must run the motors at the minimum and maximum RPM and make sure the motor s achieve these RPM Field IQ Calibrations After the hydraulics test is complete the display calibrates your system The available calibrations are Field IQ Rawson Control Module Servo Pump or PWM Pump Pressure Sensors Implement LIft Switch When the calibration is complete save the data to a configuration file and export it to the USB drive See Chapter 8 Data Advanced Use the Advanced option in the Implement screen to configure the following Controller and Material Type Selection Implement Setup Section Switching Setup Field IQ System Status Advanced 76 CFX 750 Display User Guide Implement Application Controller Controller and Material Type Selection Select this option to return to the Controller Type screen For more information see Introduction page 68 Implement Setup Use this option to adjust the following settings e Implement Measurements If you select this option the display returns you to the Implement Measurements screen in the Field IQ setup wizard See Step 7 page 73 e Section Control Module Setup If you select this option the display returns you to the second part of the Field IQ setup wizard See Step 8 page 73 Section Switching Setup Use this option to view and adjust the following settings Setting Coverage switching overlap Boundar
81. idance screen or the optional remote control tap Note If you use the vehicle on a public roadway you must put the red EZ Pilot system override switch in the off position 62 CFX 750 Display User Guide Vehicle 4 Disengaging the system The EZ Pilot system automatically disengages when one of the following happens e The vehicle is outside the configured engage limits e You pause the system e GPS positions are lost e You tap the Engage button on the guidance screen e You press the Engage button on the optional EZ Remote joystick You can manually disengage the EZ Pilot system by turning the steering wheel this overrides the electric motor Check this setting before you start using the system by engaging on a line and then turning the wheel until the system disengages To adjust the amount of force required to disengage the system change the Override Sensitivity in the Engage Options screen Engage status indicators Engage status Icon color Ready to engage Engaged Cannot engage Curve Auto steering accuracy in headlands It is possible to engage the EZ Pilot system on headlands with sharp corners at the edge of the field However the EZ Pilot system may be unable to drive around these sharp bends Use one of the following methods to compensate e Manually steer the vehicle around the corner Once you have rounded the corner re engage the EZ Pilot system e Inthe Engage Options screen increase the Disengage
82. ided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted and provided that you do these two things a Accompany the combined library with a copy of the same work based on the Library uncombined with any other library facilities This must be distributed under the terms of the Sections above b Give prominent notice with the combined library of the fact that part of it is a work based on the Library and explaining where to find the accompanying uncombined form of the same work CFX 750 Display User Guide 3 8 You may not copy modify sublicense link with or distribute the Library except as expressly provided under this License Any attempt otherwise to copy modify sublicense link with or distribute the Library is void and will automatically terminate your rights under this License However parties who have received copies or rights from you under this License will not have their licenses terminated so long as such parties remain in full compliance 9 You are not required to accept this License since you have not signed it However nothing else grants you permission to modify or distribute the Library or its derivative works These actions are prohibited by law ifyou do not accept this License Therefore by modifying or distributing the Library or any work based on the Library you indicate your acceptance of this License to do so and all its terms and cond
83. in the System menu if you have an EZ Remote joystick installed For more information see the EZ Remote Joystick Quick Reference Card Use the Z Remote screen to e assign functions to buttons 1 4 on the EZ Remote joystick e adjust the LED brightness of the buttons 144 CFX 750 Display User Guide System 9 e review your button assignments EZ Remote ts a Keypad ees Assignment Wizard K a EZ Remote LED 50 Brightness B EZ Remote Keypad Assignments EZ Remote Keypad Assignment Wizard 1 On the CFX 750 display tap the first EZ Remote joystick button that you would like to program In the Choose a Function screen tap the function you would like to assign to the joystick button See Using the EZ Remote joystick page 42 3 Inthe Finished screen select either Choose another button to repeat Step 1 and Step 2 Complete this wizard to exit the wizard EZ Remote LED Brightness Use this screen to adjust the brightness of the LED buttons on the joystick Enter a number between 0 100 EZ Remote Keypad Assignments The EZ Remote Keypad Assignments screen shows the functions that have been assigned to the four programmable buttons EZ Remote Keypad Assignments Button 1 Button 2 Button 3 Button 4 Show Trailing Map View Show Overhead Map View Finish a Line oom Out CFX 750 Display User Guide 145 9 System EZ Remote operation When the Run screen is active on the CFX 750 display use t
84. ing down the power button the Power Down In Progress screen appears Power Down In Progress Power down In progress Release button to cancel Seconds until power downc 2 Note To cancel the power down process release the power button before the three second countdown is complete Resetting the display Occasionally you may want to reset the display settings There are two ways to do this e Soft reset This returns all settings to the factory defaults All saved field data remains intact e Hard reset This returns all settings to the factory defaults and deletes all saved data including any field data CFX 750 Display User Guide 29 3 Getting Started Note Do not perform a hard reset unless it is absolutely necessary or you are instructed to do so by Trimble Technical Support Soft reset 1 Power down the display and then power it on 2 Wait until the status bar at the bottom of the second startup screen is over half full 3 Press the power button and top brightness control button at the same time 4 Hold the buttons down until the display beeps Hard reset 1 Power down the display and then power it on 2 Wait until the status bar at the bottom of the second startup screen is over half full 3 Press the power button and both brightness control buttons at the same time 4 Hold the buttons down until the display beeps The USB socket The USB socket is on the rear of the display See
85. is delete files that you no longer require 1 Inthe Manage Data screen tap Internal and then Delete Data 2 Select the information that you want to delete and then follow the wizard until the files are deleted Note If a field is currently open it will close prior to the deletion CFX 750 Display User Guide 137 8 Data 138 CFX 750 Display User Guide System In this chapter Introduction Display Advanced EZ Remote joystick Unlock Upgrade Status CFX 750 screen Recalibrate touchscreen CHAPTER This chapter describes how to configure the system settings CFX 750 Display User Guide 139 9 System Introduction The System menu enables you to adjust a variety ofthe CFX 750 display settings To access the System menu 1 From the guidance screen tap H 2 From the Settings screen tap The following screen appears lle Quick Start Wizard Unlock Up grade an EZ Remote oO Recalbrate Touchscreen K The following sections describe the various items that are available in the System menu Display Use the items in the Display screen to adjust the appearance of your CFX 750 display Units You can display distances speeds and areas in either US Imperial or Metric format By default the display uses the US Imperial format The available units for each format are outlined below Unit US Imperial Metric Distance inches centimeters feet meters miles kilometers Speed miles pe
86. itions for copying distributing or modifying the Library or works based on it 10 Each time you redistribute the Library or any work based on the Library the recipient automatically receives a license from the original licensor to copy distribute link with or modify the Library subject to these terms and conditions You may not impose any further restrictions on the recipients exercise ofthe rights granted herein You are not responsible for enforcing compliance by third parties with this License Warranty Remedies Trimbles sole liability and your exclusive remedy under the warranties set forth above shall be at Trimbles option to repair or replace any Product that fails to conform to such warranty Nonconforming Product and or issue a cash refund up to the purchase price paid by you for any such Nonconforming Product excluding costs of installation upon your return of the Nonconforming Product to Trimble in accordance with Trimbles product return procedures than in effect Such remedy may include reimbursement of the cost of repairs for damage to third party equipment onto which the Product is installed if such damage is found to be directly caused by the Product as reasonably determined by Trimble following a root cause analysis Warranty Exclusions and Disclaimer These warranties shall be applied only in the event and to the extent that a the Products and Software are properly and correctly installed configured inter
87. k eee ee RR eS 147 ad ara 2 5 a ea dae ieee eae eek Ree PPOs eee aos 147 DiS as Gch AS eer ed eee eee Sh GO ee ee Gk ae A eee 147 EF E ss ae os hk enh RIE eo Ben Pane Bk AG Se A BE eS 148 Rescalbrale TOUCISCIOO INS edite Bene Bea acre o Gite Grd were ah reads ed SB 148 CFX 750 Display User Guide 13 Contents 14 CFX 750 Display User Guide Introduction This manual describes how to install configure and use the Trimble CFX 750 display version 1 00 Even if you have used other Global Positioning System GPS products before Trimble recommends that you spend some time reading this manual to learn about the special features of this product If you are not familiar with GPS visit the Trimble website www trimble com for an interactive look at Trimble and GPS About the product The Trimble CFX 750 is an in cab touchscreen display that provides affordable guidance steering and precision agriculture functionality The CFX 750 display includes a built in GPS receiver that you can upgrade to receive GLONASS satellite signals The display can also use an array of components to maximize efficiency when planting spraying spreading and strip tilling including the Trimble Field IQ crop input control system CHAPTER Related information Sources of related information include the following e Release notes The release notes describe new features of the product information not included in the manuals and a
88. lahad working with tha current field To map a new e field or select an existing field select Yes e AB line or select an existing AB line in the current field select No Note If you select Yes then the current field automatically closes This means that you cannot cancel out of the New Field wizard and go back to your current field Guidance lines To create a guidance line you define a start point A and an end point B Once you define the A and B points the display draws a line between them This is the master AB line Note AB lines are stored automatically You do not have to actively save an AB line When you define the first guidance line the display copies it to create additional guidance lines Distance between guidance lines When you define the AB line you specify the width of the implement that is attached to the vehicle The display uses this measurement to calculate the distance between the guidance lines Ifyou do not want the guidance lines to be exactly one implement width apart you can set an overlap or skip Headlands You can record a headland boundary or you can work without a headland 112 CFX 750 Display User Guide Mapping and Guidance On screen appearance When the guidance screen shows the trailing view it tags the guidance lines with the following icons These icon s Are tagged to The first swath to the left of the master line where left is relative to the directi
89. lement connection To check that the CFX 750 display and your implement controller are communicating correctly access the VR Controller Status screen 1 Inthe Settings screen tap Vehicle and then tap Status 2 Tap VR Controller Status A screen similar to the following appears VR Controller Status Name HAADI 5500 Status Lonnaciod 3 Check that the status displays Connected CFX 750 Display User Guide 101 5 Implement Application Controller Note If the status displays Not Connected verify that the controller cable is securely connected to the display Ifthe cable is secure verify that the display and the controller are configured correctly as detailed in the sections above 102 CFX 750 Display User Guide CHAPTER Mapping and Guidance In this chapter This chapter describes the type of guidance information that the CFX 750 display provides Introduction Configuring the Guidance settings Starting Guidance Fields Resetting guidance Guidance lines Guidance Patterns Coverage logging The pause resume function Curve smoothing CFX 750 Display User Guide 103 6 Mapping and Guidance Introduction While you work guidance information appears on the CFX 750 display screen and the integrated lightbar that indicate the e position of your vehicle in the field e guidance lines e offline distance To receive this guidance information and any assistance from an auto steer system you must do th
90. llow at least one 1 hour for the system to fully discharge Before you open the system make sure that the pressure gauge on the manifold reads zero and that the cooling tower is not cold to the touch This ensures that all liquid NH3 has evaporated and that the pressure is discharged Note Frost on any component is a positive indication of trapped NAS at low pressure Lack of frost does not always indicate a lack of NH3 CFX 750 Display User Guide 7 Safety 8 CFX 750 Display User Guide Contents a A EE II 5 cr A E AA 5 Working with anhydrous ammonia sssaaa eee 6 Servicing the equipincol sse rs skarr esse oras a ees 7 1 introductio lt so KDA e oe EE R 15 ADONDE PIQUE porcion rr ar 15 Relateq Een Ee save a aca Pe Gacw ee erat ee eee be Bae eee ee ee eee 15 Tecunicala sistance meso Gob pe eee eee ee ee eee eee bee eee 15 2 installing the Display and Antenna lt lt lt 17 System COMPONCHUS vais 4s RA Aa ARAS A 18 Teal the display se teasad ad eaaa E address eh renos ad Bae 18 Connecting th display rasero rra raro ha4 R 20 Standalone CFX 750 WAAS EGNOS OmniSTAR XP HP corrections 21 Standalone CFX 750 RTK corrections 000000 ee eee 22 stan AS ciel 010 0 R ee T a sore ee ee ee ee E 22 3 Getting Started 25 DispPlarbDasic es esop aran roer poa 26 ELOUE VIEW soe he Oe Soe aa AAA AA 26 Backers tee ee Poa arpa an a 27 Cleaning the
91. me you tap the icon guidance snaps to the next nearest curve Continue tapping the icon to cycle through other guidance lines Note To use this feature the vehicle must be within 1 5 swath widths of a FreeForm curve Using FreeForm curves in spiral fields If you are creating a spiral into the center of the field drive the full circuit and then back onto the start ofthe FreeForm curve Continue to record your guidance path as you spiral toward the center of the field If you encounter an obstacle in the field continue to record your path as you drive around it On the next pass the guidance line will adjust to reflect this Note When you create a spiral with the FreeForm guidance pattern there may be a space at the center of the spiral Using FreeForm curves in fields with variable terrain Start and stop recording guidance at the ends of each pass If there are two guidance lines in close proximity tap i C2 to snap to the correct line At any point you can add a straight AB line for repeated straight line guidance Tap l c to switch between straight AB and FreeForm curve guidance lines CFX 750 Display User Guide 119 6 Mapping and Guidance Coverage logging Coverage logging draws a solid block of color behind the vehicle to show the area that you have applied When you pass over an area for the second time the color ofthe covered area changes This is useful for viewing overlaps To begin coverage logging tap lt a whil
92. mplement Setup options Option Enter a This adjusts guidance Notes measurement and coverage between logging when Implement Width 1 00 328 01 0 305 99 990 m Overlap Skip 394 skip and 394 To avoid skips in application coverage overlap set an intentional overlap 1000 cm 108 CFX 750 Display User Guide Option Left Right Offset Forward Back Offset Implement Draft Implement Mount Type Enter a measurement between 1969 right and 1969 left 5000 cm 1188 behind and 384 forward 3018 cm 975 cm 393 7 left and 393 7 right 1000 0 cm This adjusts guidance and coverage logging when The implement if offset from the vehicle center line The implement is not centered directly under the GPS antenna for EZ Steer systems or the fixed axle of the vehicle for Autopilot systems There is a variable implement draft caused by a side slope and or an implement pulling to one side Using guidance on curved segments Mapping and Guidance 6 Notes When configured and online the implement should be over the guidance line with the vehicle to the side For guidance when driving use the LEDs on the lightbar For more information see Reading lightbar patterns page 41 Set a Forward Offset when the implement is forward of the antenna on the front of the vehicle for EZ Steer systems or forward of the fixed axle of the vehicle for Autopilot systems
93. n To clean the CFX 750 display use the following supplies e Ammonia free glass cleaner Note Do not apply glass cleaner directly to the touchscreen e Soft lint free cotton cloth e 50 isopropyl alcohol 1 Apply a small amount of glass cleaner to the cloth and gently rub it against the touchscreen 2 To clean off any stains or smudges use a cotton cloth dampened with 50 isopropyl alcohol X Tip Clean the display while it is switched off It is easier to see dirt and fingerprints when the touchscreen is dark Power up To turn on the display press the power button on the rear of the display After a short time the Welcome screen appears Y The first time that you turn on the CFX 750 display the following wizards appear 28 CFX 750 Display User Guide Getting Started 3 e Touchscreen calibration Touchscreen Calibration Please calibrate your touchacresn by pressing on the target as it appears in multiple locations or sereern Take care ba press the center of the target for optimal calibration If the calibration is mot sufficient the process will repeat You must calibrate the touchscreen before you can use the display to do this follow the onscreen instructions e The Quick Start wizard To configure your system properly make sure that you run the entire wizard See The Quick Start Wizard page 32 Power down To turn offthe CFX 750 display hold down the power button for three seconds While hold
94. n of the Library The precise terms and conditions for copying distribution and modification follow Pay close attention to the difference between a work based on the library and a work that uses the library The former contains code derived from the library whereas the latter must be combined with the library in order to run GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING DISTRIBUTION AND MODIFICATION 0 This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License also called this License Each licensee is addressed as you A library means a collection of software functions and or data prepared so as to be conveniently linked with application programs which use some of those functions and data to form executables The Library below refers to any such software library or work which has been distributed under these terms A work based on the Library means either the Library or any derivative work under copyright law that is to say a work containing the Library or a portion ofit either verbatim or with modifications and or translated straightforwardly into another language Hereinafter translation is included without limitation in the term modification Source code for a work means the preferred form of the w
95. n setting up the HARDI 5500 controller refer to the HARDI instruction manual Advanced Use the Advanced option in the Implement screen to configure the following Boom Setup Swath Control Rate Control Off When Stopped Rate Snapping Boom Setup Note The boom setup on the CEX 750 display must match the setup on the HARDI controller If the boom setup differs between the display and the HARDI controller a warning message appears on the display CFX 750 Display User Guide 81 5 Implement Application Controller Use this option to view and adjust the following settings Setting Notes Implement width Enter a width between 1 00 328 01 0 30 99 99 m Fence Nozzles Enter the locations of any fence nozzles Number of sections Enter a number between 1 10 Swath Control Use this option to view and adjust the following settings Setting Notes Boom control Enter a width between 1 00 328 01 0 30 99 99 m Coverage switching overlap Control the amount of boom switching overlap allowed before the section will be switched by the system Enter a value between 1 99 Boundary switching overlap Control the amount of overlap on a boundary before the boom section is switched off Enter a value between 1 99 On Off valve latency Tune the section switching to allow for hardware delays Enter a time between 0 0 10 0 seconds Intentional overlap Set a distance to be overlapped when moving to an uns
96. nd then select GPS GPS Setup GPS Correction Source RTK 2 Select the option for Trimble VRS Modem and then select Continue 3 From the device selection list select the required Trimble modem option Correction Delivery Choose pour method for receming ATK correctoras and press the green forward TOW Device Selection Choose the device for delivering ATE corrections and press the green forward TOW 130 CFX 750 Display User Guide Data 8 Configuring VRS settings 1 Connect the modem and turn it on 2 Select the required Trimble modem and then follow the on screen instructions The first step in the VRS setup wizard is Wireless Modem Setup This is required only for Trimble modems where you have installed a SIM card Wireless Modem settings are as follows The SIM card provider is responsible for providing any settings required Wireless Modem Setup Edit settings by pressing ench ome irdi a Presa the green accept button to Tort ina Wireless modem settings Description Mobile Network Access Point Name usually required by the network GPRS User Name Mobile Network User name optional setting check with your mobile network if this setting is required GPRS Password Mobile Network Password optional setting check with your mobile network if this setting is required CPIN SIM PIN optional password lock to restrict use of the SIM card The next steps in the wizard guide you through
97. ne distance Vehicle specific performance Before you use the EZ Steer system consider the following performance suggestions Vehicle type Performance hint 2WD tractor With tractors that have SuperSteer for example New Holland TG if the tractor has a SuperSteer front axle for best performance e Reduce the Online Aggressiveness value e Line up close to the swath and make certain that the front wheels are straight before engaging the EZ Steer system e To get smoother performance when the vehicle is pulling an implement over tilled ground enable the Diff Lock This prevents the machine from pulling sharply to the left or right If you are calibrating on a hard surface turn off Diff Lock AWD tractor The EZ Steer system can be installed on Case IH STX tractors with Accusteer For optimal performance disable Accusteer using the switch in the cab if possible CFX 750 Display User Guide 55 4 Vehicle Vehicle type Performance hint Sprayer e It is common for these vehicles to have slow steering To compensate for this use high aggressiveness e If you experience large slow oscillations increase the aggressiveness e When you configure the system on a sprayer the Sprayer steering delay setting is available on the Vehicle Setup screen e Some sprayers have steering that is slow to react after you turn the steering wheel The system uses the steering delay setting to compensate for this slowness and ensure that steering corre
98. nter of the back wheel Note that the wheelbase measurement for tracked vehicles is exactly half of the length of the track Antenna height Ground to the top of the GPS antenna Antenna to axle Center the axle of the front or rear wheel to the top of the GPS offset antenna Note Make sure that you take this measurement to within 7 6 cm 3 in as an incorrect distance may result in poor steering performance Take the measurement from the antenna to the correct point of your vehicle as follows e Rear axle MFWD Sprayer Floater Truck e Front axle Awd tractor Combine e Track center Tracked tractor If the antenna is e in front of the axle enter a Forward distance e behind the axle enter a Behind distance 60 CFX 750 Display User Guide Vehicle T3 roll calibration Calibrating the T3 roll sensor enables the display to calibrate terrain compensation in the IMD 600 This step requires you to 1 Enter an accurate value for the IMD 600 orientation Controller Orientation Label faces up connector faces front j i Label up connector front Pe ij 3 conector right 2 Park the vehicle and mark the inside of both sets of wheels 3 Remain stationary while the system calculates the roll offset This takes approximately 20 seconds 4 Turn the vehicle around and ensure the wheels are over the positions marked in the previous step 5 Remain stationary while the system calculates the
99. ny changes to the manuals The release notes are available at www trimble com e Trimble training courses Consider a training course to help you use your GPS system to its fullest potential For more information go to the Trimble website at www trimble com training html Technical assistance Contact your Trimble Reseller for technical assistance CFX 750 Display User Guide 15 1 Introduction 16 CFX 750 Display User Guide CHAPTER Installing the Display and Antenna In this chapter This chapter introduces the CFX 750 display and system components and also describes how to system components install the display and antenna E m Installing the display m Connecting the display E Installing the antenna CFX 750 Display User Guide 17 2 Installing the Display and Antenna System components Item Description CFX 750 display RAM mount and screws Quick reference card Compact disc GPS antenna cable Power bus CAN cable Power cable AG25 Antenna G G e 0900600 0 AG25 Antenna mount plate Installing the display Part number 94110 00 61958 78838 00 ENG 78821 02 50449 77282 67258 01 77038 62034 Mount the CFX 750 display in the vehicle cab When you position the display make sure that e itis within the drivers reach the USB drive is easy to remove and replace e the touchscreen is easy to see but the display does not block the drivers view e it does not interfere with the driver
100. o ensure user safety Failure to do so may result in serious injury or death CFX 750 Display User Guide 5 Safety A N WARNING When the implement is down and the master switch is in the On position the machine is fully operational Take all necessary precautions to ensure user safety Failure to do so could result in injury or death A N WARNING The display contains a single use Lithium sulfide LiSO2 battery Do not expose the battery to temperatures greater than 71 C 160 F as the battery may explode A N WARNING MOVING PARTS DURING THIS TEST Please stay clear of the implement Ensure the implement is raised the transmission is in PARK and the emergency brake is applied before continuing Working with anhydrous ammonia Contact your NH3 supplier to review all safety requirements associated with anhydrous ammonia NH3 Always wear correct personal protective equipment This includes but is not limited to Goggles or face shield Protective suit and gloves Respirator Do not allow anyone to operate the system without proper instruction and training Stand up wind when working around NH3 and related equipment Always keep NH3 equipment away from buildings livestock and other people Never work on NH3 equipment in confined spaces Before you attempt to transport the implement discharge the system of all NH3 and completely shut down the system See Discharging the system page 7 If symptoms of illness occ
101. ocket and then copy the prescription file to the display s internal memory See Retrieving data from the USB drive page 137 3 From the guidance screen tap I to create a new field or select an existing field The CFX 750 display searches the internal memory for prescription files and after you define or select a field the following screen appears in the wizard Available Prescriptions List E None None i L00riverbull shp Annex Road Prescription shp Corn plus 50 bu beans ship 9 CFX 750 Display User Guide 69 5 Implement Application Controller 4 Select the prescription file that you require and then tap v The following screen appears Prescription Parameters Edit settings by pressing sach one PCV d Rate Column Press the green accept button to continga y Scale Factor 3 Rate Outside zero Prescription 5 Configure each of the items in the Prescription Parameters screen N CAUTION For the system to work correctly you must choose the correct Rate Column setting If you do not then the applied rate will be incorrect Field 1Q The Field IQ crop input control system enables the CFX 750 display to control the following e planters e sprayers e liquid strip till toolbars e spinner spreaders Additionally it enables the display to use Tru Count air clutches or Tru Count LiquiBlock to perform automatic section control and or use a prescription with Rawson drives to control seed or liquid fer
102. of overlap on a boundary before the boom section is switched off Enter a value between 1 99 On Off valve latency Tune the section switching to allow for hardware delays Enter a time between 0 0 10 0 seconds Intentional overlap Set a distance to be overlapped when moving to an unsprayed area or out of a sprayed area Enter a distance between 0 00 32 10 0 00 10 00 m Target Rate Set the target application rate that will be sent to the Rawson controller Enter a rate between 0 0 11000 0 Alternatively you can load a prescription so the CFX 750 display will automatically send target rates to the Rawson controller 88 CFX 750 Display User Guide Implement Application Controller 5 Note When the CFX 750 display is sending target rates to the Rawson controller the Rawson controller will only display the Target Rate screen To change or view any other screen on the Rawson controller you must unplug the CFX 750 display cable Note When using a prescription with the Rawson controller the target rates in the prescription must match the step sizes in the Rawson controller For example if the default is 25000 and the step size is 4 then the target rate values accepted by the Rawson controller are 26000 27000 28000 40000 Otherwise the Rawson controller may not be able to apply the correct rate Default Rate On the CFX 750 display set the same target rate that appears on the Rawson controller when you first
103. om the antenna to the correct point of your vehicle as follows e Rear axle MFWD Sprayer Floater Truck e Front axle 4wd tractor Combine e Track center Tracked tractor If the antenna is e in front of the axle enter a Forward distance e behind the axle enter a Behind distance T2 roll calibration Calibrating the T2 roll sensor enables the display to calibrate terrain compensation in the EZ Steer controller This step requires you to Enter an accurate value for controller orientation Park the vehicle and mark the inside of both sets of wheels e Remain stationary while the system calculates the roll offset This takes approximately 20 seconds e Turn the vehicle around and ensure the wheels are over the positions marked in the previous step e Remain stationary while the system calculates the roll offset This takes approximately 20 seconds EZ Steer calibration In this step you must drive and engage on a straight AB line in a clear field 1 Begin driving and tap A l 2 Drive 160 feet and then tap E CFX 750 Display User Guide 53 4 Vehicle A series of calibration screens will allow you to adjust any settings as necessary Operation You must calibrate and set up the EZ Steer system before operation Engaging the system Before you can engage the EZ Steer system you must e open a field in the guidance screen e define an AB line e position the vehicle within the configured en
104. on Thousands of seeds per hectare Thousands of seeds per acre Kilograms of seed per hectare Pounds of seed per acre Liters per hectare Gallons per acre Kilograms of fertilizer per hectare Pounds of fertilizer per acre Kilograms of anhydrous per hectare Pounds of anhydrous per acre Kilograms of nitrogen per hectare Pounds of nitrogen per acre CFX 750 Display User Guide 71 5 Implement Application Controller A N WARNING Anhydrous ammonia NH3 can cause severe burning blindness or death Before you begin to operate or service equipment that contains NH3 carefully read and follow all safety instructions in Working with anhydrous ammonia page 6 Installing the Field 1Q hardware For information on installing the Field IQ crop input control system on your implement refer to e Field IQ Platform Installation Instructions Tru Count Air Clutch Installation Instructions e Rawson Installation Instructions For the latest versions of these documents go to www trimble com agriculture Setting up the Field 1Q system The CFX 750 display automatically detects the Section Control Modules and or the Rawson Control Modules installed on your implement When you use the wizard to set up your Field IQ system the screens that appear may differ according to the modules you have installed If during the setup a screen appears that you are unsure of you can either e Tap to go back and check the previous screen s e Tap
105. on the L1 master line was drawn not the vehicle s current position Note the following The master line that you created The swaths are based on this line The A start and B end point on the master line e The current swath and tag are orange e Ona Pivot pattern the swaths are numbered out from the center not from the initial swath The second line to the left of the master line Guidance Patterns Select a guidance pattern that enables you to create a guidance line to suit your field 1 From the guidance screen tap lip and then tap Create New Field 2 Inthe Create New Field screen tap Pattern Type 3 Select the pattern that you want to use Pattern To learn more see Straight AB page 114 A line page 114 Identical curve page 115 Adaptive curve page 115 Pivot page 116 Headland page 116 FreeForm page 118 6 CFX 750 Display User Guide 113 6 Mapping and Guidance Straight AB Use a straight AB line when you do not need to define headlands and you want to drive the field in parallel straight lines Note When the vehicle is on a guidance line the line extends 1 km 0 6 miles before point A and 1 km beyond point B This makes it easier to see where the next swath is and to get online after a turn Mapping an AB line 1 Drive to the start point of the master line 2 Tap A and then drive to the end of the line 3 When the icon is highlighted tap 18 The master AB line appears 4
106. on the display spins when the Rawson master switch is on and the lightbar receives flow messages from the controller 90 CFX 750 Display User Guide Implement Application Controller 5 Amazone controller Setup 1 Once you select Amazone as your controller the following screen appears on the display Output Port _ MN Port A an Note Do not configure the display to output NMEA messages on the same port that your controller is connected to 2 3 On the Amazone controller go to the Settings menu Change Remote to Enable For more information on setting up the Amazone controller refer to the Amazone instruction manual Advanced Use the Advanced option in the Implement screen to configure the following Boom Setup Swath Control Rate Control Target Rate Turn Off Rate on Overlap Rate Snapping Boom Setup Note The boom setup on the CFX 750 display must match the setup on the Amazone controller If the boom setup differs between the display and the Amazone controller a warning message appears on the display CFX 750 Display User Guide 91 5 Implement Application Controller Use this option to view and adjust the following settings Settings Implement width Fence Nozzles Number of sections Swath Control Notes Enter a width between 1 00 328 01 0 30 99 99 m Enter the locations of any fence nozzles Enter a number between 1 10 Use this option to view and adjust
107. onnected Farm option On tapping Connected Farm Setup takes you directly to the Connected Farm Setup screen 132 CFX 750 Display User Guide Data 8 The following sections describe the menu options available from the Connected Farm Setup screen Device name Use the on screen keypad to give your device a name that you will recognize once you transfer the data to your personal computer Modem only setup Use this option to set up your wireless modem Once you have connected your modem the following screen appears Modem Detected Wa have successfully detected your wireless modem Continue to the next screen to attempt to conrect to the network In the Wireless Modem Setup screen you can adjust the following e APN Setup String e SIM PIN e Network username change the username used for network registration e Network password change the password used for network registration After you set up your modem the following screen appears Network Operational Longratulaticre You have successTuly sel Up your wireless modem Once you receive this message you can continue with the registration process CFX 750 Display User Guide 133 8 Data Note The internal settings for your modem are on the SIM card that your modem uses For further setup information contact your SIM card provider Network registration Register your information with the Connected Farm Network Use the username and password you created
108. or delete the following features e rock e line tree e area e weed Exclusion v exclusion The Auto steer icon From the guidance screen tap to quickly adjust the aggressiveness setting for the EZ Steer or Autopilot system x 8 Aggress iveness Reading lightbar patterns When lit the LEDs show the position of your vehicle relative to your intended guidance line As your vehicle position changes in relation to the guidance line the LEDs move left or right Use the lightbar to obtain accurate guidance when e you have set an implement offset or implement draft e fine tuning guidance on straight swaths The LEDs in the integrated lightbar show the position of your vehicle relative to the guidance line e When your vehicle is on the guidance line the three central green LEDs are lit CFX 750 Display User Guide 41 3 Getting Started e As your vehicle moves off the guidance line the lit LEDs move left or right and change to red Note that the LED pattern that appears has a different meaning for each Main Lightbar LED Mode For more information see the table below and Lightbar Setup page 142 This LED pattern Indicates that the vehicle is A Py on the guidance line FEAT Off the guidance line For this pattern if the Main Lightbar LED Mode is set to e Chase the vehicle is offline to the left e Pull the vehicle is offline to the right CO main Lightbar LED Mode is set to
109. or off 2 Enter a time between 0 0 10 0 seconds CFX 750 Display User Guide 39 3 Getting Started Intentional overlap You can use this option to make sure that when applying there are no gaps in coverage if you move into an uncovered area or out of a covered area Use this option To set the distance that you want to travel before On overlap distance Exiting a covered area and switching the implement on Off overlap distance Entering a covered area and switching the implement off Target rate Use this option to set the target application rate the amount of product you want to apply Enter a number between 1333 41333 Valve aggressiveness If you use an auto steer system such as an EZ Steer or Autopilot system you can use this option to adjust how the system responds to steering changes Note the following e A higher setting brings the vehicle back on line quickly but may cause tight oscillations e A lower setting gives a more moderate response to bringing the vehicle back on line but can avoid overshoot Enter a setting between 50 150 The Field icon From the guidance screen tap I to create a new field or select an existing field See Chapter 6 Mapping and Guidance The Guidance icon From the guidance screen tap MU to quickly nudge shift or resume a guidance line 40 CFX 750 Display User Guide Getting Started 3 The Mapping icon g From the guidance screen tap to quickly add
110. or the current rate switch position This is the amount of product that you want to apply O Actual rate The actual application rate This is the amount of product that is currently being applied Rate switch position Indicates the current position of the rate switch O Section control Shows the current mode for the controller Automatic Manual 75 78 CFX 750 Display User Guide Implement Application Controller 5 Item Description Notes Master switch status Master switch on Master switch off G Pressure P1 The current pressure reported by the primary pressure sensor P2 The current pressure reported by the secondary pressure sensor Field 1Q master switch box A B C Feature Function O Increment decrement Increases the applied amount by a set amount the amount set in the switch Setup screen Rate tab e Rate switch Choose to use preset Rate 1 preset Rate 2 or Manual rate LEDindicator Red Unit is powered but not communicating with the CFX 750 display Green Unit is powered and communicating with the CFX 750 display Yellow Unit is initializing communications with the CFX 750 display O Automatic Manual section Automatic mode The CFX 750 display automatically opens and closes switch sections when entering areas of overlap non apply zones or crossing boundaries Manual mode The sections are controlled manually bypassing the CFX 750 display X Tip You can switch from Automati
111. or your controller The EZ Pilot Setup screen contains the following options e Engage Options e Vehicle Setup e Aggressiveness e Vehicle Calibration menu The following sections describe each option CFX 750 Display User Guide 57 4 Vehicle Engage Options Use this option to view and adjust the settings described below Setting Minimum Maximum speed Maximum Angle Engage Disengage Offline Override sensitivity Operator timeout Notes Enter the minimum and maximum speeds at which the EZ Pilot system will disengage e Minimum between 1 0 and 15 9 mph 1 6 and 25 5 kph e Maximum between 1 0 and 18 0 mph 1 6 and 28 8 kph The EZ Pilot system will not engage when the vehicle is heading toward the guidance line at an angle greater than the Maximum Angle Enter an angle between 5 and 45 degrees Engage offline The system will not engage when the vehicle is offline further than the Engage Offline distance Enter a distance between 0 5 and 27 0 0 2 and 8 2 m Disengage offline The system will automatically disengage when the vehicle is offline further than the Disengage Offline distance Enter a distance between 0 6 and 27 00 0 2 m and 8 2 m Control how much force is required to disengage the system Enter an increment between 1 100 Enter a time between 1 60 minutes Vehicle Setup Use this option to view and adjust the settings described below Setting Vehicle type Whe
112. ork for making modifications to it For a library complete source code means all the source code for all modules it contains plus any associated interfacedefinition files plus the scripts used to control compilation and installation of the library Activities other than copying distribution and modification are not covered by this License they are outside its scope The act of running a program using the Library is not restricted and output from such a program is covered only ifits contents constitute a work based on the Library independent of the use of the Library in a tool for writing it Whether that is true depends on what the Library does and what the program that uses the Library does 1 You may copy and distribute verbatim copies of the Library s complete source code as you receive it in any medium provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty keep intact all the notices that refer to this License and to the absence of any warranty and distribute a copy of this License along with the Library You may charge a fee for the physical act of transferring a copy and you may at your option offer warranty protection in exchange for a fee 2 You may modify your copy or copies of the Library or any portion of it thus forming a work based on the Library and copy and distribute such modifications or work under the terms of Section 1 above provided that
113. play alerts you when your machine is within a specified distance of a tight turn The threshold is set between 1 and 10 To increase the sensitivity of the alert lower the number Auto U turn detection Auto U turn detection operates only on FreeForm and adaptive curve patterns For more information see Guidance Patterns page 113 Use this mode To On Off Automatically detect that the vehicle has done a U turn and generate the next guidance line Manually control when a path is finished With the FreeForm pattern you must manually stop recording With the adaptive curve pattern you must manually set the B point Coverage Settings Configure the Coverage Settings options to suit the requirements of your system Coverage on off delay If you activate coverage logging at the same time as you enable your spraying or spreading system set a coverage delay that matches the time it takes for flow to start when you turn on your spraying spreading system This ensures that the display records coverage from the actual start point of application You can enter a delay time between 0 0 10 0 seconds CFX 750 Display User Guide 105 6 Mapping and Guidance Coverage logging Use this mode Disabled Manual Engaged Switch Nudge Settings Option Clear nudge at swath end Reset nudge Nudge increment To Turn coverage logging off Turn coverage logging on and off manually Automatically enable cover
114. plement Setup options cc8408 h eee been de HbR OSS aE we eo 108 Using guidance on curved segments 00 eee ee ee 109 Using guidance on straight segments 2 2 ee 109 Creating straight sections on Headland or Curve swaths nsan sasaaaa aaaea aan 110 FOIS a a a dao es e ee es 110 Creatine mew cl cares roer eey EES 110 Selecting loading a field rra ae o A 110 Adding an AB line to a current field onnan anauaa aa 111 Selecting loading an AB line into a field nanana 111 RECord KCCOINE 2 raros osas sa a oe es E 111 MS A III 110 Guia anco eS erre Fae Pra ees Ge de eee eee as 112 Distance between guidance nes ooo 112 Ie pobres ene aes eee sarral 112 Oniscreen appearaCO a4 ressrao Ge EER as ee a a ae T E 113 EIS Te Paes sra rca AAA AAA 113 eE L 2 445042 parres or rra eee he eee ee eae eee ros 114 L beis te ee Bees ee ee eee eee Se ee eee eee ee oe ae 114 IGM RICA Ea scada ae eee eee Bhan ee Ae OR EE AS 115 a ky ea R end ee eae tae ee eae eee eRe eee ea oo BE ee 115 E ee aw od BSE SRE REE OE EEG ER OEE RE Re ee eee Oe 116 Headland cestas Shoe goed betes posos ee tee eee cra ues 116 DICE OM 5442566 os ee Ree OR aeee Cae eee ee eee aw eee ee Be oe we 118 CONG ASC IOUSING ce cenando terme eee ee eee eee eee ee dra ees 120 The pause resume function o oooo ee ete eee eee 120 CFX 750 Display User Guide 11 Contents 12 Clive SMIOO Mine narcosis aaron Ar 120
115. plication Controller Boom Setup Note The boom setup on the CEX 750 display must match the setup on the LH 5000 controller If the boom setup differs between the display and the LH 5000 controller a warning message appears on the display Use this option to view and adjust the following settings Setting Notes Implement width Enter a width between 1 00 328 01 0 30 99 99 m Fence Nozzles Enter the locations of any fence nozzles Number of sections Enter a number between 1 10 Swath Control Use this option to view and adjust the following settings Setting Notes Boom control Enter a width between 1 00 328 01 0 30 99 99 m Coverage switching overlap Control the amount of boom switching overlap allowed before the section will be switched by the system Enter a value between 1 99 Boundary switching overlap Control the amount of overlap on a boundary before the boom section is switched off Enter a value between 1 99 On Off valve latency Tune the section switching to allow for hardware delays Enter a time between 0 0 10 0 seconds Intentional overlap Set a distance to be overlapped when moving to an unsprayed area or out of a sprayed area Enter a distance between 0 00 32 10 0 00 10 00 m Rate control Use this option to view and adjust the following settings Setting Notes On Application rates are sent from a prescription loaded in the display or the targe
116. power up it up Enter a number between 0 9999000 Step Size The step size increases or decreases the actual applied rate by the percentage that you select You can choose from one of the following settings e 2 e 4 o 6 2 Rate Snapping Due to pump constraints liquid flow is generally inconsistent To control how these inconsistencies appear on your display turn rate snapping on or off Setting Notes On Matches the actual applied rate to the target rate when within 10 of the value Off Shows all fluctuations in the actual applied rate CFX 750 Display User Guide 89 5 Implement Application Controller Operation When you connect the Rawson controller to the display the following items appear on the CFX 750 guidance screen lt OP ole OF a Ea Status gt Guidance HE he E ae Can t engage Too slow reine T 20 0 gala A 0 0 gal a BR R oe 3 4 Item Description Notes O Quick Access icon See Quick Access icon page 38 Boom section status Shows the current state of each boom section indicators e Green Enabled and spraying e Gray Enabled but not currently spraying e Red The section is off the switch is off Target rate If a prescription is loaded P displays to indicate that the prescription rate is being used rather than the target rate O Actual rate The actual application rate This is the amount of product that is currently being applied Application indicator The wheel
117. prayed area or out of a sprayed area Enter a distance between 0 00 32 10 0 00 10 00 m Rate control Use this option to view and adjust the following settings Setting Notes On Application rates are sent from a prescription loaded in the display or the target rate manually configured on the display Off The target rate must be set on the HARDI controller The CFX 750 display does not send target rates to the controller This is the default setting Note When sending a target rate to the HARDI 5500 controller that is higher than 99 9 the display rounds to the nearest whole number For example 0 99 9 is not rounded 101 4 is rounded to 101 Off When Stopped You can use this option to control whether the system allows the vehicle to continue operating when it is not moving If the vehicle is a clutch operated planter select No so you can continue planting even when stopped 82 CFX 750 Display User Guide Implement Application Controller 5 Rate Snapping Due to pump constraints liquid flow is generally inconsistent To control how these inconsistencies appear on your display turn rate snapping on or off Value Notes On Matches the applied rate to the target rate when within 10 of the value Off Shows all fluctuations in the actual applied rate Operation When you connect the HARDI 5500 controller to the CFX 750 display the following items appear on the guidance screen 0 0 Man Ea
118. r Use the OnPath Filter option to detect and eliminate GPS position jumps and significantly improve pass to pass accuracy Select the option that best describes the surrounding environment Satellite Health You can use this setting to disregard signals from a specific satellite due to concerns about its state For more information contact your reseller Status The Status screen enables you to view the current status of the GPS functions ey GPS Status DGPS Status GPS Status The GPS Status screen displays information about your position and the current GPS signal strength Satellite Status The Satellite Status screen displays information about the current satellite constellation 124 CFX 750 Display User Guide GPS 7 The information for each satellite is contained in one line The following table describes fields that the line contains Field Description Sv Satellite number Note GLONASS satellites have an R in front of the satellite number GPS satellites do not El Elevation Az Azimuth DLA SNR L2 L2 SNR Corr Correction Only appears if correction is applied Used Used Only appears if the satellite is used in position calculation ss Ss DGPS Status The DGPS Status screen displays which DGPS signal is selected from the GPS Correction Source screen For more information see GPS Setup page 122 Filter Status The Filter Status screen provides diagnostic information about the OnPath a
119. r hour kilometers per hour Area acres hectares 140 CFX 750 Display User Guide System 9 Color Scheme You can adjust your color scheme according to the cab lighting and time of day For more information see Backlight page 142 This color scheme Is suitable for Day A brightly lit environment Note This is the default color scheme Dimmed Dark and low cab light environments Red Dark and low cab light environments Time Zone The GPS receiver provides UTC formerly GMT time To display and log times in your local time set the time zone offset Location standard Time Offset Daylight Savings Time Offset _ US Eastern Time 5 00 4 00 US Central 6 00 5 00 US Mountain 7 00 6 00 US Pacific 8 00 7 00 Australia East 10 00 11 00 excludes QLD Australia Central 9 30 10 30 excludes NT Australia West 8 00 8 00 View There are three options for the map views View Description Auto Headland The view automatically swaps between overhead view in headlands and trailing view on swaths Auto Engage The view automatically swaps between overhead view not engaged and trailing view engaged Manual You must manually change between overhead and trailing view Status Popup Transparency Use this option to control the transparency level of the status popup tab At this level of transparency The tab is 10 completely solid 1 barely visible CFX 750 Display User Guide 141 9 System Ba
120. rmation and access to various system functions The availability of the text and icons depends on the set up of your system For example some icons are not available while you are using an auto steer system To activate an icon tap it with your finger Ifthe display does not respond when you tap it see Recalibrate touchscreen page 148 The following sections describe the icons that can appear on the guidance screen 34 CFX 750 Display User Guide Getting Started 3 Status Tapping Sd scrolls through several pop up screens that describe various system settings Field Name 083110 0001 gt Field Area 0 00 a D Productive Area 0 00 a Coverage 0 00 a Status Nudge g Imp Width 60 00 Overlap A Storage Settings To remove the pop ups continue to tap Sd until they disappear Settings Pl Tap S to open the Settings screen Use the Settings screen to adjust your system settings and view the status of the following Setting For more information see Vehicle Chapter 4 Vehicle page 47 Implement Chapter 5 Implement Application Controller page 67 Guidance Chapter 6 Mapping and Guidance page 103 GPS Chapter 7 GPS page 121 Data Chapter 8 Data page 127 System Chapter 9 System page 139 View The options for viewing the guidance screen are e Zoom In e Zoom Out e Change View CFX 750 Display User Guide 35 3 Getting Started Note Change View toggles between the Overhead view
121. rred unit of Measurement 4 To set up your system complete each page of the wizard See the section below Using the setup wizards The CFX 750 display contains various wizards that guide you through the task of configuring your system The following table describes how to use the wizards to enter your system settings Select the setting you require The field that displays the desired value When you make your selection the field changes color from gray to green Enter the numbers that you require Enter text Accept the selection and go to the next screen Accept the selection and exit the screen CFX 750 Display User Guide 33 3 Getting Started Navigate the wizard Yu gt 2 gt W Guldance Go back to the previous page Exit the wizard Note When you exit the wizard the system retains any settings you have already selected for any settings that you have not yet entered the system uses the settings from the previous configuration Access the on screen help The guidance screen 1 l m P nr a ee ma Tai grii fay fet ee 1 ES L oF LU hs L LF ne Mp a Status gt lt lt gt E Scllings A a View iT Field 10 Can t engage Too slow T 20 0 gal a Pl N A Tx A 0 0 gala 10 Els c P2 N A R iy WI Fleld U Guidance Mapping Tp lal Autogheer Setup A oe The guidance screen displays a mix of text and icons that provide operating info
122. s e e ee rasgado boo ee eee eee ees aes 57 A AAA A EAS 57 CAMO AION 64 uns ee oe a eee EP eos a ee eye ee eee eee 59 OPEO Coat hee aee hte tener eared ehh tame ae oud ea hae oe S 62 The Autopilot automated steering system annaua 65 o eed eee eae Pee ee REO ed eee ee eee Oe ee Bes 65 o aed haeae ee E eee ae we oh ae ke ee ee 65 5 Implement Application Controller lt lt 67 IO reus fo eee ee aon ed oo ee es ea ee oe eee oe ee S 68 caja o A eae ates Cee ALO we aoe Gee eee ee eee Be 69 Sas Kanaan sane ee ee oo eae oa ee ee ee ee Ge eae ee ee eee a de 70 DEMONS a across nados sra oasis Bena Rs 71 Units of measure A bebe beeen ees ee eee eeeeeee oes 71 Installing the Field IQ hardware 2 0 eee eee Ta Setting up the Field IQ system aero a ad 72 A Ones Ch Gee eae PEt ae ee eee eee dea eee seset eae 76 ODEON 2454024 E eee beet II 78 IST RIE CONUONCH suka n bets too te eee Rh eae eee Gaede eee eee ae 81 DCU 2a nea ee eeu eee Re eee eee eee eee eee eee ee ee eo eee ba Se ee 81 MOVANCEO Gab 4oe er Chee oan Go oes a shee eae eee ee PE ee ae ee ee te ae 81 OPS xsara abe deseo een 4 ba be baa Gee eee eee eee ee 83 Raven controllers A 84 eraa erea IIA 84 a e 85 UperatiOA casara rotando cero roer rro ridad 86 LEN AA O E 87 o oak eee eee Gt ee eee eee ee ee ee eee ee 6 eo 87 PON ANCE Oe a a aig ona eee eke ee OS eaa 4 eee ee pe ee Se 88 Y A oe eo ees oe Stee eee eh a 90 Amazone 2 5445 5456 rer eak E
123. sed on the explanations below When we speak of free software we are referring to freedom of use not price Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software and charge for this service if you wish that you receive source code or can get it if you want it that you can change the software and use pieces of it in new free programs and that you are informed that you can do these things To protect your rights we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it For example if you distribute copies of the library whether gratis or for a fee you must give the recipients all the rights that we gave you You must make sure that they too receive or can get the source code If you link other code with the library you must provide complete object files to the recipients so that they can relink them with the library after making changes to the library and recompiling it And you must show them these terms so they know their rights We protect your rights with a two step method 1 we copyright the library and 2 we offer you this license which gives you legal permission to copy distribute and or modify the library To protect each distributor we want to make it very clear that t
124. ser Guide Implement Application Controller 5 Turn Off Rate on Overlap Use this option to view and adjust the following settings Settings Notes Yes Does not spray over an area that has been previously sprayed No Sprays over an area that has been previously sprayed Operation When you connect the Amazone controller to the display the following items appear on the displays guidance screen Item Actual rate Target rate Boom section status indicators Application indicator Quick Access icon LH 5000 controller Setup Notes If a prescription is loaded P displays to indicate that the prescription rate is being used rather than the target rate Shows the current state of each boom section e Green Enabled and spraying e Gray Enabled but not currently spraying e Red The section is off the switch is off The wheel on the display spins when the Amazone master switch is on and the lightbar receives flow messages from the controller See Quick Access icon page 38 1 Once you select the LH5000 as your controller the following screen appears on the display Output Port Port A 2 On the CFX 750 display make sure that Output Port matches the port on the display that the controller is connected to COM or AUX CFX 750 Display User Guide 93 5 Implement Application Controller 3 Do not configure the display to output NMEA messages on the same port that your controller is connected to
125. t rate manually configured on the display Off The target rate must be set on the LH 5000 controller The CFX 750 display does not send target rates to the controller This is the default setting Note When sending a target rate to the LH 5000 controller that is higher than 99 9 the display rounds to the nearest whole number For example 0 99 9 is not rounded 101 4 is rounded to 101 Target Rate Set the target application rate that will be sent to the LH 5000 controller Enter a rate between 0 0 11000 0 98 CFX 750 Display User Guide Implement Application Controller 5 Single section boom switching Use this to turn off the implement in areas that have already been applied Note This setting can only turn the entire boom on and off It does not support individual sections e Select Yes to avoid spraying an area that has previously been sprayed e Select No to spray an area that has previously been sprayed Rate Snapping Due to pump constraints liquid flow is generally inconsistent To control how these inconsistencies appear on your display turn rate snapping on or off Value Notes On Matches the applied rate to the target rate when within 10 of the value Off Shows all fluctuations in the actual applied rate Bogballe controller Setup 1 Once you select Bogballe as your controller the following screen appears on the display Output Port Port A Note Do not configure the display to output NME
126. t the end of the first curve tap 18 The system generates the next swath Continue to drive the swaths setting the B point at the end of each one Using the adaptive curve pattern for row finding 1 2 3 4 Pivot Use the pivot pattern on fields that use center pivot irrigation With this pattern you can drive concentric circles around the center pivot To map a pivot Note Always set the master line near the outer edge of the field Set Auto U Turn Detection to Off Create a guidance line based on the adaptive curve pattern Set the B point at the end of each row Turn the vehicle toward the next swath When the vehicle is halfway through the turn guidance along the next swath appears 1 Drive to the start point of the pivot 2 Position one wheel of the vehicle in a pivot wheel rut with the rear of the vehicle to the pivot arm If the field is not a full circle pivot face the rear of the vehicle to the edge of the field 3 Tap A and then drive around the field Keep the vehicle in the rut The display will generate guidance swaths 4 Turn left or right for the next swath As you move toward the next swath it appears on the screen and turns orange to show that it is selected 5 Steer the vehicle so that the lit LEDs are centered on the lightbar as you drive forward along the swath Headland The headland pattern enables you to define the boundary headland of the area as well as the guidance lines con
127. tained within it Use the headland pattern to allow room to turn 116 CFX 750 Display User Guide Mapping and Guidance 6 The following diagrams show the two headland patterns Single Multiple A When you start to define the headland you define the internal guidance line as you drive around the headland and then you complete the headland You can change two settings for the headland pattern e The number of circuits e The internal pattern Number of circuits When you create a headland you need to specify the total number of circuits including the master headland This defines how wide the headland is Note No matter how many circuits you create only define the outside headland The inner headlands are copied from that original circuit Internal pattern The internal pattern is the pattern of the guidance lines inside the headland Choose from the following Choose this pattern To create Straight AB Standard parallel swaths inside a headland A Parallel swaths at a pre defined heading Reselecting the headland When you use the headland pattern you can see either the headland or the internal pattern To see the headland guidance again when you are driving the internal pattern drive into the headland before the first internal swath or after the final internal swath The headland appears automatically Mapping a headland 1 Drive to the start point of the headland 2 Tap o to set the start point of th
128. te Gdn Bee aks 134 Sending Field data using Connected Farm 2 2 aaa ee 135 Receiving Field data through the Connected Farm service ooo ooo 135 Nanade Data esos tenen etarra 136 AA II 136 Clearing the internal memory arresta ee ee eee 137 DUST q ndo RARA AAA ARAN AAA 139 MOOO sacarnos rra AAA esau 140 Di Nesse Erene ee bee ee haeee obese gees eae 140 Uli ee ee ee ee ee ee eee ee ee ee eee ee 140 Color Somone os een aoe ope s eee bee heat eee ee ne sere ee eee ese 141 TMC ZOU 4s beecagt III 141 NIOW ear anno ana sea eee eee eens ada 141 Status Popup Transparency ssc rassa addat 24 e ag eee HRP e Oe Be 141 Paeko a8 262 ree ern Ae oe eee eee deca rosa boa 142 Touchscreen speaker volume annaa aaa ee eee 142 CFX 750 Display User Guide Contents a A a pena os ea GPR Bede gee Oe ae ee yay Bd 142 PCIM A fe eas rn ee ek ith hes aii ee oh ee ee ee ee a eg 143 Save Load COn ratos natos eth dou are ae e Poh eG ew ene WO K 143 Dita wae ee Ao oe hae RDS SRS ES ORY Eee ee R 143 Enable Advanced User Cone 4 3 E EEE L be bee kee Be RE AGE GES ES 144 O O Gere tart A OS AN 144 EZ Remote JONS cau td dd il de dd o det Bae Gs 144 EZ Remote Keypad Assignment Wizard eos pS hae ia 145 EZ Remote LED DMShINeSss E E E E EN EE 2 145 EZ Remote Keypad Assignments 2 454448 na AR Oe Se ad 145 EZ Remote opera Oks da a oh ER ee AA 146 Unlock NS 2 6 5 db babs om ASG eer deed d OSG Ae hehe oh Bes Gree Z 9 147 Uperadins your MSP ar is S
129. ted lightbar with 27 LEDs When lit the LEDs show the position of your vehicle relative to your intended guidance line For more information see Reading lightbar patterns page 41 CAUTION Do not press on the screen with a sharp item such as a pencil or screwdriver you may damage the surface of the screen 26 CFX 750 Display User Guide Back view Item and oo O O Description Power button Brightness controls Note You can also use the Color Scheme and Backlight menu options to set the screen brightness See Color Scheme page 141 and Backlight page 142 USB socket GPS connector Port A Power connection socket Port B Radio access panel Getting Started 3 44 1 CHT II L i i Notes Turns the display on or off e To increase the brightness of the screen press e To decrease the brightness press You can connect a USB memory stick to the display to transfer data to and from the unit For more information see The USB socket page 30 Connects the GPS cable P N 50449 to the display Connects external devices to the display Connects the power cable P N 67258 to the display Connects external devices to the display If you purchase the optional RTK module install the module here For more information see the install instructions supplied with the radio module CFX 750 Display User Guide 27 3 Getting Started Cleaning the touchscree
130. the following settings Settings Boom control Coverage switching overlap Boundary switching overlap On Off valve latency Intentional overlap Rate control Notes Enter a width between 1 00 328 01 0 30 99 99 m Control the amount of boom switching overlap allowed before the section will be switched by the system Enter a value between 1 99 Control the amount of overlap on a boundary before the boom section is switched off Enter a value between 1 99 Tune the section switching to allow for hardware delays Enter a time between 0 0 10 0 seconds Set a distance to be overlapped when moving to an unsprayed area or out of a sprayed area Enter a distance between 0 00 32 10 0 00 10 00 m Use this option to view and adjust the following settings Settings Notes On Application rates are sent from a prescription loaded in the display or the target rate manually configured on the display Off The target rate must be set on the Amazone controller The CFX 750 display does not send target rates to the controller This is the default setting Note When sending a target rate to the Amazone controller that is higher than 99 9 the display rounds to the nearest whole number For example 0 99 9 is not rounded 101 4 is rounded to 101 Target Rate Set the target application rate that will be sent to the Amazone controller Enter a rate between 0 0 11000 0 92 CFX 750 Display U
131. tial hazard which if not avoided can cause severe injury CAUTION This alert warns of a hazard or unsafe practice which if not avoided can cause injury or damage Note An absence of specific alerts does not mean that there are no safety risks involved WARNING Anhydrous ammonia NH3 can cause severe burning blindness or death Before you begin to operate or service equipment that contains NH3 carefully read and follow all safety instructions in Working with anhydrous ammonia page 6 WARNING Incorrect adjustment of the Manual Override Sensitivity calibration setting could cause this critical safety feature to fail resulting in personal injury or damage to the vehicle Any adjustment to this setting should only be made by an experienced user WARNING During the Deadzone calibration the system moves the vehicle s steering wheels To avoid injury be prepared for sudden vehicle movement WARNING When you tap the liquid flow calibration Start button the machine will become operational Take all necessary precautions to ensure user safety Failure to do so may result in serious injury or death WARNING When you tap the control valve calibration Start button the machine will become operational Take all necessary precautions to ensure user safety Failure to do so may result in serious injury or death WARNING When you tap the fill disk Start button the machine will become operational Take all necessary precautions t
132. tilizer rates The different functions of the Field IQ system that you can configure and control are Application Main functions Planter e Seed section control of up to 48 individual rows Field IQ section control module s needed using Tru Count air clutches e Seed rate control using up to 4 Rawson drives to change seed population Field IQ Rawson Control Module s needed e Liquid fertilizer control of up to 48 individual liquid nozzles Field 1Q section control module s needed using Tru Count LiquiBlock valves e Variety tracking Sprayer e Liquid section control of up to 48 individual rows Field IQ section control module s needed using existing boom shutoff valves or Tru Count LiquiBlock valves e Connects to spraying systems that are configured with servo pump servo PWM bypass dump and master valves 70 CFX 750 Display User Guide Application Strip till liquid Spreading Definitions Term Section Row Master Switch Box MSB 12 Section Switch Box 12SSB Section Control Module SCM Rate and Section Control Module RSCM Rawson Control Module RWCM Implement Switch Main functions Implement Application Controller 5 Liquid section control of up to 48 individual spray nozzles Field IQ Section Control Module s needed using Tru Count LiquiBlock valves Liquid ratecontrol using up to 2 Rawson drives connected to fixed displacement pumps such as CDS John Blue piston pumps to
133. tion is compromised Option Description Favor Accuracy Provides the highest level of accuracy Balanced Quality Trades potential accuracy for a slight increase in production time Favor Availability Extends production time further with more potential for reduced accuracy Advanced The Advanced screen enables you to view and adjust advanced GPS settings g Use SHAS satellites in thre position fix Antenna Type Access the Antenna Type screen to alter the internal settings of the GPS receiver to ensure optimum accuracy for the antenna Select the antenna you have connected to the display The AG15 and AG25 antennas are white and dome shaped Use SBAS satellites in the position fix Choose this option if you want to use SBAS corrections from WAAS satellites to calculate the GPS positions For example if the display receives position information from six standard GPS satellites and two WAAS satellites the display uses all eight satellites to calculate the GPS position This can extend operating time when limited number of satellites are available Note This option does not work with EGNOS satellites OmniSTAR or RTK corrections CFX 750 Display User Guide 123 7 GPS Force GPS lono Choose On to force the use of modeled rather than real time ionosphere data This setting is designed primarily for locations at the edge of SBAS coverage such as northern Canada and could affect accuracy if used elsewhere OnPath Filte
134. touchscreen 44 24 Gan Ge tierra rara ae 28 POWT Urs codes increase as paraa so 28 POWELL WI parao oe gee eae ae eo bee ee ye ee ee 29 Resetting Ne display 4 sera daa daea SHELA SCG e T a op ET E Ae 29 Tne 8 e o E E eee E E E E E E E E E 30 Removing a USB drive se ceripacas aa 31 ls esre serrare t eae Reheat as eRe ee eee eee ee A ae 32 The QuickStart VVS arl 6 ooo deca rss ras traii nepsi eta L 32 Usine the sep Wizarde OSA Gee eee eae Oe od Cee SSE SEE Oe Se OEE Ee 33 TNC SIG TOG TOI error rare ee ee eee oes eee E tay 34 o oe eo ee ee a ee ee ee ee es ee ee ee ee 35 Dees ate teehee eee hae hee hs E E ee eae E ae ee 35 VOW ps ee ee ee a ee ee ee ee ee ee ee eee 35 EXVCNGCE COS errores we oS Be Ree ee eed ee oe eS eS ee oe amp 37 OUI OOE ICO betheck neers due ee R REE ER RE R REE 38 Lx Te AO sopresa pres Gene oe raras 40 The Gudane iGO rasero 40 THEMPO O ejer dejos praia cerrar a 41 dotes ICOM a 4can4eeeeers ee eee ne tees eeeeet eens eee a ea ee 41 Reading lentbar paltas seer E prorrata eee ERE oh eee eee 41 Using the EZ Remote joystick pst eres e445 Se RAR a ewd 42 CFX 750 Display User Guide 9 Contents On scr encon ercer praia RAE AAA AAA 43 S SOS A EI INE III 47 A op Ben oo REM oe oh AG hehe eee chee 5 oe 48 The EZ Steer assisted steering system 1 o 49 DOU 44 sews eos 4k Oe eee he ee ee eee he eee ee ee 49 EH e A E AA 51 Operator arras o rro ros rr ra 94 The EZ Pilot assisted steering system
135. ur during or shortly after use of NH3 products seek immediate medical attention Keep a source of clean water at least five gallons readily available In case of exposure flush exposed skin or eyes immediately with large quantities of water and seek immediate medical attention NH3 can be harmful to the environment if not used correctly Follow all local state and federal regulations regarding proper handling of this chemical 6 CFX 750 Display User Guide Safety Servicing the equipment E 2 Remove the system from operation before performing any maintenance Thoroughly bleed all system lines and disconnect the nurse tank hose See Discharging the system page 7 Make sure that the gauge pressure is at zero before you open the system Use extreme caution when opening a previously pressurized system Discharging the system L o NS ot p 10 Turn off the console or vehicle master switch Completely close the main shut off valve on the supply or nurse tank Resume field application until the pressure gauge shows zero pressure Check again that the console and or vehicle master switch and all section switches are turned off Completely close the emergency shut off valve the cooling tower Bleed and disconnect the nurse tank supply hose from the system Turn on the console master switch and all section switches Stand up wind from the implement and then slowly open the bleed valve s until fully open A
136. uto Steer and then EZ Pilot Setup Auto Steer x Auto Steer System a TER E EZ Pllot Setup Note If the EZ Pilot Setup button does not appear tap Auto Steer System Type and then select EZ Pilot for your controller 3 In the EZ Pilot Setup screen tap EZ Pilot Calibration Wizard The wizard guides you through the following processes Entering your vehicle measurements Troll calibration EZ Pilot calibration Note To complete the above processes you must have GPS connected Entering vehicle measurements For optimum guidance you must take accurate vehicle measurements and enter them into the display Note Do not enter calibration numbers from EZ Guide Plus or EZ Steer systems This may cause very poor vehicle control including swerves and or large oscillations To streamline the calibration process you may want to take the vehicle measurements and record them for entry later on CFX 750 Display User Guide 59 4 Vehicle The techniques for taking vehicle measurements are described below to learn about implement measurements see Implement Setup options page 108 Before you take the measurements position your vehicle as follows 1 Park the vehicle on level ground 2 Make sure that the vehicle is straight with the centerline of the body parallel to the wheels 3 Take the vehicle measurements To take this Measure from the measurement Wheelbase Center the axle of the front wheel to the ce
137. when you purchased Connected Farm For more information contact your Trimble reseller Connected Farm data transfer Note The Connected Farm service requires a subscription For more information on purchasing a subscription contact a Trimble reseller To configure Connected Farm operations 1 Tap and then select Data Connected Farm Setup 2 To enable the feature select the option to turn on the Connected Farm service The setup menu now includes a number of settings as shown below If you are a first time user of the Connected Farm service select Initial Setup to open a setup wizard Connected Farm Setup y Cornactad Farm i Ga A Connected Farm setup option Description Connected Farm registration Initial Setup First time Connected Farm setup wizard This requires a DCM 300 modem to be connected and in an area with good wireless service Once the initial setup is complete you can change individual settings as required 134 CFX 750 Display User Guide Data 8 Sending Field data using Connected Farm Connected Farm field data includes event coverage field boundaries guidance lines area features line features and point features You can wirelessly transfer all this data from the CFX 750 display to the office With Connected Farm enabled field event data is automatically sent to the Connected Farm service when you close the event To manually send field events l Tap gt and then select Dat
138. x to discard all of the changes and start again To set up your Field IQ system 1 From the guidance screen tap 2 From the Settings screen tap Implement The Controller Type screen appears 3 Select Field IQ Controller Type Which controller do you have connected 4 The Field IQ Hardware Summary Screen appears Press Cy to continue through the setup wizard 72 CFX 750 Display User Guide Implement Application Controller 5 In the Application Controller Mode screen select what you are using the implement for Row crop planting Liquid Granular seed Granular spreading Anhydrous Note If you change the Application Controller Mode the display erases any previous calibrations 6 In the Rate and Section Control screen select one of the following section Control Only Rate Control Only Both Note Ifyou do not have at least one section control box and at least one Rawson control box installed both options will not appear 7 In the Implement Measurements screen edit each of the setting items Note that the items that appear in this screen vary depending on the Application Controller Mode chosen previously In this part of the wizard you must indicate the following For Rate Control CFX 750 Display User Guide 73 5 Implement Application Controller a Where on your implement each module is located Hardware Location Left Using the serial mumbar indicate which 1234
139. y Note Do not enter calibration numbers from EZ Guide Plus or EZ Steer T2 systems This may cause very poor vehicle control including swerves and or large oscillations To streamline the calibration process you may want to take the vehicle measurements and record them for entry later on The techniques for taking vehicle measurements are described below to learn about implement measurements see Implement Setup options page 108 Before you take the measurements position your vehicle as follows 1 Park the vehicle on level ground 2 Make sure that the vehicle is straight with the centerline of the body parallel to the wheels 3 Take the vehicle measurements To take this Measure from the measurement Wheelbase Center the axle of the front wheel to the center of the back wheel Note that the wheelbase measurement for e Tracked vehicles is exactly half of the length of the track e Articulated 4WD vehicles is half of the distance between the center of the front and rear wheels 52 CFX 750 Display User Guide To take this measurement Antenna height Antenna to axle offset Vehicle Measure from the Ground to the top of the GPS antenna Center the axle of the front or rear wheel to the top of the GPS antenna 4 Note Make sure that you take this measurement to within 7 6 cm 3 in as an incorrect distance may result in poor steering performance Take the measurement fr
140. y switching overlap On Off valve latency Intentional overlap Notes Control the amount of boom switching overlap allowed before the section will be switched by the system Enter a value between 1 99 Control the amount of overlap on a boundary before the boom section is switched off Enter a value between 1 99 Tune the section switching to allow for hardware delays Enter a time between 0 0 10 0 seconds Set a distance to be overlapped when moving to an unsprayed area or out of a sprayed area Enter a distance between 0 00 32 10 0 00 10 00 m Field 1Q System Status Select this option to view the status for the following a Master Switch Module e Section Switch Module Rate Control Module Section Control Module OEM Switch Interface Accessories CFX 750 Display User Guide 5 17 5 Implement Application Controller Operation Once you have enabled configured and calibrated your Field IQ crop input control system the following items appear on the guidance screen T lt O 07 5 6 Mph u gt lt W mg gt a W Settings Guidance m oa Lhe 1 ES aan T y Autost Press or use footswitch to engage sc T 10 0 gal a Pl 10 PSI o TS 1 N 0 0 galia p Tk P2 12 PSI Xn N y oS Item Description Notes Quick Access icon See Quick Access icon page 38 Coverage status On Inactive ET Off Target rate The target application rate f
141. you wish to copy part of the code of the Library into a program that is not a library 4 You may copy and distribute the Library or a portion or derivative of it under Section 2 in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machine readable source code which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange If distribution of object code is made by offering access to copy from a designated place then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code even though third parties are not compelled to copy the source along with the object code 5 A program that contains no derivative of any portion of the Library but is designed to work with the Library by being compiled or linked with it is called a work that uses the Library Such a work in isolation is not a derivative work of the Library and therefore falls outside the scope of this License However linking a work that uses the Library with the Library creates an executable that is a derivative of the Library because it contains portions of the Library rather than a work that uses the library The executable is therefore covered by this License Section 6 states terms for distribution of such executables When a work that uses the Li

CFX-750 Display User Guide

Contents

Download Pdf Manuals

Related Search

Related Contents