User manual as PDF
Contents
1. Rear view XSR Standard Program 101210 XSR 3B 111210 XSR 3B US with NEMA 5 15 Rear view 101220 XSR 3R 111220 XSR 3R US with NEMA 5 15 Front view A 101230 XSR 3R 3R 111230 XSR 3R 3R US with NEMA 5 15 Rear view Front view Rear view 17 Svvisson 10 12 11 XSR 5B 111211 XSR 5B US with NEMA 5 15 Rear view 101221 XSR 5R 111221 XSR 5R US with NEMA 5 15 Front view Rear view 101231 XSR 5R 5R 11 12 31 XSR 5R 5R US with NEMA 5 15 Front view Rear view 101216 XSR 5B5 111216 XSR 5B5 US with NEMA 5 15 Rear view 101226 XSR 5R5 111226 XSR 5R5 US with NEMA 5 15 Rear view 101233 XSR 5R5 5R5 111233 XSR 5R5 5R5 US with NEMA 5 15 Rear view 18 101235 XSR 5R2 5R2 111235 XSR 5R2 5R2 US with NEMA 5 15 Front view Rear view 101234 XSR 5R 5R5 111234 XSR 5R 5R5 US with NEMA 5 15 Front view Rear view 101232 XSR 5R2. The XSP XSR splits the line into smaller segments with a regenerated signal which reduces the delay of the reflection at each segment Reflection Reflection with small with small delay delay Signal OK Signal OK SvvissSOn Protection In case of an over voltage on the DMX and RDM line s all devices on that line can be damaged The XSP XSR separates the line into multiple segments The over voltage is restricted to the concerned segment The XSP XSR itself is well protected against transient over voltage and the optical isolation of each port prevents a damage to other ports and segments in case of a permanent over voltage XSP Block Diagram Control Logic Optical Optical Optical Optical Optical Receiver Isolation Isolation Isolation isolation Isolation Line J777777777 7 y i Termination Transmitter Transmitter Transmitter Transmitter Transmitter lt lt Termination SvvissOn XSR Block Diagram t t t t t t E t t t t t t E VAI VANVAIVATVA Line Transceiver Transceiver Transceiver Transceiver Transceiver t t t t t t t t t t Termination Termination DMX Only Q Mains Connection Two different mains connections are available The US versions are delivered by SWISSON with an Edison Plug NEMA 5 15 These models carry a US suffix at the end The international versi
3. Svvisson XSP XSR DMX Splitter amp RDM Hub User Manual USER MANUAL Svvisson SvviSSOn English Revisions History Copyright O 2012 SWISSON AG SVVISSON XSR and XSP DMX Splitter Booster amp RDM Hub Introduction The XSR and XSP series of RDM hubs and DMX splitter boosters from SWISSON can easily and economically be integrated into any lighting system where it is desirable to split and boost DMX and RDM signals While the XSP splits and boost only DMX signals the XSR also detects RDM data and uses its bidirectional functionality to report back to the controller Lighting Board All output ports on both XSP and XSR are optically isolated A strong power supply allows for a reliable operation in a broad voltage range A large program of XSR and XSP devices is available consisting of different housings different connector types and different numbers of input and output ports Applications Concert Lighting TV Sets Live Events Theme Parks Multimedia Shows e Achitectural Lighting Theater e Installations Typical Application 2 DMX Light Board with or without 2 RDM functionality i i DMX Ea DMX Dimmers with or without with or without i i RDM functionality The XSR works within DMX RDM environments but can also operate mainly in pure DMX environments The XSR is a good solution for those who expect to use RDM in future because the XSR a
4. 3R 111232 XSR 5R 3R US with NEMA 5 15 Front view Rear view 101250 XSR TR5 111250 XSR TRS US with NEMA 5 15 Rear view 101251 XSR TR5 TR5 11 12 51 XSR TR5 TR5 US with NEMA 5 15 Rear view 101251 XSR IB5 W Front view Rear view 19 Technical Data Mains Voltage Main Frequency Current Consumption Single Units Current Consumption Double Units Operating Temperature Protocol Standard Safety Standards EMC emission EMC immunity SVVISSON 100 240 VAC 50 60 Hz 0 2 A 0 4 A 0 F to 131 F 17 C to 55 C ANSI E1 11 DMX 512 ANSI E1 20 RDM EN60950 1 UL508 EN55103 1 EN55103 2 No part of this documentation may be reproduced or transmitted in any form or by any means electronically or mechanically including photocopying and recording without the prior written permission of SWISSON AG The information in this documentation is supplied without warranty of any kind either directly or indirectly and is subject to change without prior written notice SWISSON AG its employees or appointed representatives will not be held responsible for any damages to software hardware or data arising as a direct or indirect result of operating and or handling the product s mentioned herein Issued by S
5. B 111162 XSP 5B US with NEMA 5 15 Rear view 101172 XSP 5R 111172 XSP 5R US with NEMA 5 15 Rear view 101182 XSP 5R 5R 111182 XSP 5R 5R US with NEMA 5 15 Rear view 18 fone Ws Taya d VVIDD 101160 XSP 5B5 111160 XSP 5B5 US with NEMA 5 15 pro Rear view 101170 XSP 5R5 111170 XSP 5R5 US with NEMA 5 15 Front view Rear view 101180 XSP 5R5 5R5 111180 XSP 5R5 5R5 US with NEMA 5 15 9000300 Front view Rear view 101187 XSP 5R2 5R2 111187 XSP 5R2 5R2 US with NEMA 5 15 Front view Rear view 10 11 84 XSP 5R 5R5 111184 XSP 5R 5R5 US with NEMA 5 Front view Rear view 101186 XSP 5R 3R 111186 XSP 5R 3R US with NEMA 5 15 Front view Rear view 16 sf TM A Asr MA IDD 101150 XSP TR5 11 11 50 XSP TR5 US with NEMA 5 15 Rear view 10 11 51 XSP TR5 TR5 11 11 51 XSP TR5 TR5 US with NEMA 5 15 Rear view 101198 XSP IB5 W
6. DM packets and when receiveing RDM responses This LED is not available on XSP models XSP XSR Box Models Mains plug US Versions only cable length approx 145cm M10 female threat for clamp Ring for safety wire The M10 screw which enters the XSP XSR should not exceed a maximum length of 20mm Clamp is not included with the XSP XSR 11 SVVISSON Single Rack Models Mains plug US Versions only sf TM A SE a Svvisson Single Rack Terminal Models SvvissOn Terminal Models The terminal models of the XSP XSR series come with pluggable terminal blocks The terminal blocks are located on the back of the devices XSP XSR terminal models are shipped with the terminal blocks They can accept wires up to AWG 17 1mm Installation Models The XSP XSR installation model is manufactured to be installed by certified professionals This version has no plugs The connections are all located inside the device Input port Mains Thru po N grommet 14 SvvissOon XSP Standard Program 101163 XSP 3B 111163 XSP 3B US with NEMA 5 15 Rear view 101174 XSP 3R 111174 XSP 3R US with NEMA 5 15 O5 100000 Front view Rear view 101185 XSP 3R 3R 111185 XSP 3R 3R US with NEMA 5 15 Front view Rear view 101162 XSP 5
7. WISSON AG Fabrikstrasse 21 CH 3250 Lyss Switzerland e mail welcome Qswisson com SWISSON of AMERICA Corp 2419 East Harbor Blvd 34 Ventura CA 93001 U S A 20
8. cts as a normal DMX splitter if there is no RDM data The XSP works only within DMX evironments Unpacking The DMX Splitter is packaged in a cardboard box The following items are included The device This user manual SvviSSOn Consider the following notes mandatory when you set up connect and use the XSP XSR Safety Information This product is approved for professional use only it is not intended for household usage Follow the safety instructions closely when setting up connecting and using the device Read the manual before operating the device E and pay attention to all the instructions or warnings given in this manual or printed on the product Use this device only in accordance with local laws and regulations Safety Precautions e Disconnect the device from the AC power supply before removing any cover or part including fuse even when not in use e Ensure the device is electrically connected to ground earth e Use only a source of AC power supply that complies with local building and electrical regulations and which has both overload and ground fault earth fault protection e Connect the device to a AC power supply using the supplied power cable e Before using the device check that the power distribution equipment and cables are in perfect condition and rated for the current required of all connected devices e Isolate the device from power supply immediately if the power cable or power plug ar
9. e in any way damaged defective or wet or if they show signs of overheating e Do not expose the device to rain or moisture e Do not operate the device if any cover or component is missing damaged or deformed e Refer any service operation not described is this manual to SWISSON AG e Provide unrestricted airflow around the device e Do not operate the device where the ambient temperature exceed 55 C 131 F e Do not modify the device in any way other than described in this manual or install other than genuine SWISSON parts e Do not attempt to bypass the fuse Replace defective fuse with one of the specified type and rating only e When suspending the device ensure that the supporting structure and all hardware used is capable to withstand at least 10 times the weight of all devices suspended together e Install as described in this manual a secondary attachment such as a safety cable that has been approved by an official body such as e g TUV German Technical Monitoring Association as a safety attachment for the total weight it secures The safety cable must comply with EN 60598 2 17 Section 17 6 6 and be capable of bearing a static suspended load representing 10 times the actual weight of the device e Make sure that all external covers and rigging hardware are securely fastened e Provide clearance underneath the work area and a stable platform whenever installing servicing or moving an overhead device e Do not use
10. her models pin 4 amp 5 are not available V A Line A KNN Transceiver Protection Termination Input Port Thru Port SvvissOon Line Termination All XSP and XSR splitters have a built in line termination The termination is activated by pressing the termination button On terminal and Installation versions DMX Only only on XSR models The DMX only function removes all non DMX data before sending the data to the Output ports RDM data will be removed too This can be helpfull when DMX devices are not compatible and do not check the data they receive as valid DMX signals The DMX only function is activated by pressing the DMX only button On terminal and Installation versions the button is only accessible with a tool Output Ports The output section of The OUTPUT section versions with XLR of versions with connectors terminals output 2 E signal The OUTPUT terminals are located on the back of the devices Each Output port is individually optically isolated meaning that it is totally isolated from the other Output ports and the Input selection The Pins 4 amp 5 on models with 5 Pin XLR connectors are not connected 10 SvviSSOn ER E ME Control fone FE Logic te las 9 Isolation Transceiver Network i ES Output Port E On the XSR the indicator LED of the OUTPUT ports indicates if a valid Ed signal is transmitted It works bidirectionally m When sending DMX or R
11. ons are supplied plugless SWISSON distributors or dealers may deliver the devices with a country specific plug Yellow Green Earth Brown Phase Blue Neutral US Versions US suffix International Versions Wire US System Wire EU System Symbol ve Neutral Ground Earth yellow green Consult a qualified electrician if you have any doubts about A proper installation The socket where the device is plugged in must be close to the device and easy to access Pr JV san AA v550NN Input Section of XSP Versions The Input section of versions with XLR connectors E Swisson PUSH DMX G power E signal The Input section of the versions with terminals The input and thru terminals are located on the back of the device swisson DMX RDM 5 3 855 dy mv Es The Power LED indicates if the device is powered and if the power supply unit of the XSP is working A green LED indicates if a signal is available at the Input port A red LED indicates if the received signal is faulty The XSP has a built in line termination This can be activated by pressing the termination button A LED indicates if the termination is activated LJ amp err signal G power Input Section XSR Versions The Input section of the XSR versions with XLR connectors E rdm amp dmx only O G power The Input section of the XSR versions with terminal
12. s The input and thru terminals are located on the back of the device SvviSSONn Fale VTS Svvisson DMX RDM BG dmx only The Power LED indicates if the device powered and if the power supply unit of the XSR is working G power E signal rdm G power A multicolor LED indicates if a signal is available at the Input port The LED has 2 different states Green Signal is present and Ok Red No signal is present or signal is present but faulty E signal The RDM LED indicates if ROM data packets are preset In a pure DMX environment this LED remains in OFF state 4 rdm The XSR has a built in line termination This can be activated by pressing the termination button A LED indicates if the termination is activated J dmx The DMX only function of the XSR allows removal of all RDM data only from the Output ports A LED indicates if the DMX only function is activated RDM Identify Blinking of all Output LEDs The RMD Identify is activated Errors Blinking of DMX only LED Error UID not valid RDM operation is not possible DMX operation only Blinking of all LEDs except power and termination LED Fatal error Input and Thru Port The THRU port is hardwired with the INPUT port and allows to daisy chain the devices even when the XSR is not powered On all XSP and XSR models with a 5 Pin XLR connector the pin 4 and 5 are also looped through to the THRU port On all ot
13. the device in areas where it is exposed to direct sunlight e Do not use the device in areas that are considered to be highly inflammable 3 SVVISSON Benefits of using a XSP XSR Splitter Booster E Boost On installations with excessively long cable runs the DMX and or RDM signal can be compromised or significantly weakened by the distance good signal weak signal bad signal The XSP XSR boosts the signals thus eliminating signal interference encountered in such situations good signal weak signal good signal Regeneration In harsh environments DMX and RDM signals can be disturbed or corrupted good signal disturbed bad signal signal The XSP XSR cleans and regenerates the signals good signal disturbed good signal signal SvviSSONn Splitting A simple split of signal lines is not allowed The bidirectional operation of RDM is even more sensitive to the split than DMX nn Pr E not allowed gt gt gt PPT 133333 A split of the signal lines is possible with the XSR XSP by using different output ports Reduction of Reflection Problems Signal reflection is a common problem in large DMX installations or on long signal lines The bidirectional operation of RDM is more sensitive to reflections than DMX Weak Strong Strong reflection reflection reflection with large with large with small delay delay delay Signal OK Bad signal Signal OK
Download Pdf Manuals
Related Search