TU-2 Take Up User Manual
Contents
1. FORWARD Take up with outward curl You can take up media by using the MANUAL switch However never operate the MANUAL switch while the loading lever is engaged low ered Doing so may cause the media to be pulled with excessive force actuating the protective feature and resulting in an error 27 4 Operation How to Remove Taken up Media Z CAUTION Removal of taken up roll media from the unit is a task which must be carried out by two or more persons If dropped such items may cause injury Cut off the media For more information about how to perform cutoff refer to the user s manual included with the printer Support the paper tube to prevent it from falling Loosen the retaining screw and move the arm 0008 Detach the paper tube from the end caps Arm retaining screw 28 5 What to do if The take up unit doesn t take up media Are the power cord and AC adapter connected correctly Connect securely so that the connection will not come loose or be incomplete Is the AUTO switch set to OFF Set the AUTO switch to match the direction of take up Is the setting for the AUTO switch at the correct position Orient the setting of the AUTO switch to match the direction of take up for the media Is automatic cutoff of the media being performed Take up quits as soon as the media is cut off On the computer the2. 26 4 Operation J Take up the media O Make the setting for the AUTO switch on the take up unit Take up with outward curl TO Y AUTO MAN BACKWARD BACI L Lr FORWARD FOR Take up with inward curl AUTO MAN BACKWARD BACH FORWARD FOR While supporting the dancer roller feed out media and take it up on the paper tube While using _Y_ to feed out the media a little at a time pull the dancer roller back toward you stopping at a place where the dancer roller doesn t go back into the machine when you let go of it Let go of the dancer roller then press Y again When the take up unit starts to perform take up release Ly creased When you begin take up take care to ensure that the end of the media does not become rolledor Press BASE POINT key 4 Operation Be sure to press and set the base point the output start location Attempting to start printing with the base point left unset causes the media to be taken up with excessive force and results in a mo tor error This completes loading of the media To Take up Media Manually Take up with inward curl MANUAL 5
3. y Line up with the a A Aot e aie Line up with the bolt hole and secure in place Pull the dancer roller back toward you Dancer roller Loosen the arm adjustment screw Loosen the screw just enough to allow the arm to move left and right Arm retaining screw 17 3 Assembling and Installing Q Attach the end caps to the paper tube and secure the arm in place First fit the paper tube securely onto the end cap on the same side as the right stand leg Next press the end cap on the same side as the arm into the paper tube and securely fit the end cap into the paper tube Finally secure the arm in place using the arm retaining screw Tighten the screw while pressing down 3 from above Fit onto this securely Paper tube For the paper tube use the included item Using something other than the included item may result in spinning without traction or other problems that impede media take up 3 Assembling and Installing 4 Connect the cables NWARNING Connectto electrical outlet that complies with this machine s ratings for voltage frequency and current Incorrect voltage or insufficient current may cause fire or electrical shock insert the printer connector cable into the printer connector and connect the other end to the printer Affix large and small cable clamps at the locations shown in the figure and secure the ca
4. generates uses and can radiate radio fre quency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Unauthorized changes or modification to this system can void the users authority to operate this equipment For Canada CLASSA NOTICE This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations CLASSEA AVIS Cet appareil num rique de la classe A respecte toutes les exi gences du Reglement sur le mat riel brouilleur du Canada For California WARNING This product contains chemicals known to cause cancer birth defects and other reproductive harm including lead WARNING This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures For EU Countries Manufacturer C ROLAND DG CORPORATION 1 6 4 Shinmiyakoda Kita ku Hamamatsu shi Shizuoka ken 431 2103 JAPAN The authorized representative in the EU Roland DG Corporation German Office Halskestr 7 47877 Willich Germany Contents Contents ueniet a 1 AN To Ensure Safe Use acetil 2 Important Notes on Ha
5. media are taut Ifthe media is slack or crooked raise the load ing lever and reload the media 21 4 Operation 22 2 Fasten the media to the paper tube O Make sure the screen shown in the figure is displayed then use _Y_ to pull out the media until its leading edge reaches the paper tube Check to make sure the media is pulled out straight at this time If the media is not straight redo the loading operation You can adjust the length of the media in 10 millimeter steps by pressing Y To pull out media con tinuously hold down the key LOAD SHEET TO TAKE UP a OK 4 Using adhesive tape fasten the center and side edges of the media to the paper tube fasten a total of three locations D Secure the center of the media in place while keeping the media stretched taut to keep it free of slack While pulling the media from the center outward fasten the left and right edges D Take up with outward curl Paper tube Adhesive tape Take up with inward curl O Paper tube Adhesive tape 6 4 Operation TILT DANCER Press ROLLER TO FRONT d The media is pulled out an
6. printer Make sure the take up unit is completely flush with the stand Place so that the control box and frame are pressed against the stand leg and mounting fixture A is pressed against the caster PRO II PRO II V series SP 540V Bottom Mounting fixture A The left and right sides have no handedness Front side of the printer ELE 2 Place pressed against Place pressed against Caster Place pressed against Control box Mounting fixture A 14 3 Assembling and Installing Other Models VS series RS series VP series SP 300V 300 SP 540i 300i etc Mh with small Control bo box TI A Hex wrench au ME Mounting fixture A The left and right sides Mounting have no handedness fixture A roy Front side of the printer Q Q Place Stand leg Place pressed against again pressed _ el st 7 Stand leg Caster Place pressed gt against 5 Control box Mounting fixture A Q Attach mounting fixtures B and C and secure the take up unit to the stand Tighten the screws while holding the take up PRO II PRO II V series SP 540V unit pressed against the stand leg In Press against 9 S
7. software RIP make the setting so that the printer doesn t perform automatic cutoff For more information about the setting for automatic cutoff refer to the documentation for the software RIP Is the paper tube installed correctly Securely insert the paper tube onto the end caps If the paper tube is not attached correctly it may spin without traction and fail to take up the media P 18 3 Assembling and Installing Procedure 3 e Is the paper tube bent or sagging Media cannot be taken up smoothly when the paper tube is bent or sagging Are you using the included paper tube For the paper tube use the included item Using something other than the included item may result in spinning without traction or other problems that impede media take up P 20 About the Paper Tube Media take up is not straight Is the media loaded correctly Remove the media then redo media loading from the beginning 29 6 Appendix Locations of the Power Rating and Serial Number Labels Serial Number This is required when you seek maintenance servicing or sup port Never peel off the label or let it get dirty Power Rating Use an electrical outlet that meets the requirements for voltage frequency and amperage given here Specifications TUC 2 Rail and Accessaries TU2 74 TU2 64 TU2 54 TU2 42 TU2 30 Acceptable media widths Less than 1 879 Lessthan 1 625 Le
8. your authorized Roland DG Corp dealer 4 Operation How to Load Media NCAUTION Load roll media correctly Otherwise the media may fall and cause injury NCAUTION Roll media weighs about 30 kg 66 Ib To avoid injury handle with care NCAUTION Never load media that weighs more than 30 kg 66 Ib The printer may fail to withstand the weight and topple over or the media may fall from the unit VS series RS series VP series SP 540i 300i I Pass the media through the printer O Move the dancer roller toward the rear si Switch on the printer s sub power and when the screen shown TU in the figure appears press _ _ to select TU2 ac companying the pull back operation or TU not accompanying the pull back operation TU2 is available only when you re using the VS seriese printer RS series VP series SP 540i 300i or when selecting TU with VS series Make sure the printer s PREFEED and FEED FOR DRY menu items are each set to DISABLE For RS series make sure only the FEED FOR DRY menu For information on how to check or change setting values refer to the user s manual for the printer OK Not OK Load roll media onto the printer then lower the loading lever For information on how to perform loading refer to the user s manual for the printer After loading check the following points O The media is loaded straight O All areas of the
9. NT key 10 2 Checking the Included Items The following included items are contained in two packing cartons Make sure they are all present and accounted for Control Box TUC 2 Arm Arm retaining screw one for each Frame 1 Control box 1 lt gt Mounting fixture A 1 Mounting fixture B 1 SP y Mounting fixture C 1 SON SD e Bolts with washers 4 Small Bolts 6 lt Hex wrench small 1 Printer connector cable 1 Small Large Cable clamps small 2 large 1 Power Cord 1 AC adapter 1 2 Checking the Included Items Rail and accessories TU2 74 64 54 42 30 Dancer roller 1 Support bar 1 Rail slider 1 Paper tube 1 Pa Hex wrench large 1 Large bolts 16 User s manual this document 1 11 3 Assembling and Installing Read This First O Before attempting the operations described here first install the printer you re using at the target loca tion O Carry out the operations in a location that is flat level and stable OWe recommend carrying out the operations at a location near to where the printer you re using is installed Assembling and Installing NCAUTION Unpacking and installation must be carried out by two or more persons Otherwise the machine or the stand may fall resulting in injury I Assemble the take up unit Q At
10. Roland Automatic Media Take up Unit TU2 74 TU2 64 TUC 2 amp TU2 54 TU2 42 TU2 3O User s Manual Thank you very much for purchasing this product O To ensure correct and safe usage with a full understanding of this product s performance please be sure to read through this manual completely and store it in a safe location O Unauthorized copying or transferral in whole or in part of this manual is prohibited O The contents of this operation manual and the specifications of this product are subject to change without notice O The operation manual and the product have been prepared and tested as much as possible If you find any misprint or error please inform us O Roland DG Corp assumes no responsibility for any direct or indirect loss or damage which may occur through use of this product regardless of any failure to perform on the part of this product O Roland DG Corp assumes no responsibility for any direct or indirect loss or damage which may occur with respect to any article made using this product Roland DG Corporation For the USA FEDERAL COMMUNICATIONS COMMIS SION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment
11. When feeding out media toward the front of the machine by pressing the cursor key Y be sure to set the base point O Set the PREFEED setting menu item to DISABLE O If a FEED FOR DRY menu item is available set it to DISABLE Never use the automatic cutoff feature for media When the setting to execute automatic cutoff of the media is made on the computer media cutoff is performed when printing of one page finishes When you re performing continuous printing and take up for two or more pages turn off the automatic cutoff feature on the computer Take up quits as soon as the media is cut off Q Point For those who use the VS series printers With the machines of the VS series you can perform cutting operations by selecting TU2 from the SETUP SHEET menu Refer to the procedure 1 2 in How to Load Media on page 21 User s Manual for the VS series Using Media Take up System in Chapter 4 Part of Practice About the Paper Tube For the paper tube use the included item The included paper tube is a special part exclusively for use with this machine Using something other than the included item may result in spinning without traction or other problems that impede media take up The paper tube is a part that wears out The replacement cycle varies according to usage conditions but to ensure good media take up monitor the state of the paper tube and replace it when necessary To purchase a replacement contact
12. a ssesscsssscscseseecsssscssseesssssecssseceesuseccsuecessucessuscessueesssutecssueeesuteccsueessueeessuseceaseees 29 Media take up isinot Straighit csieiscsascsesssscocesescouisessneseasisescibsecebosciesnnsssisnesenussasnnsssSsazesseunsuenssslendzesededecostdvonoususssuededbushecnuscelee 29 6 APPO et Em 30 Locations of the Power Rating and Serial Number Labels eene tete tttnnnnntttnnnns 30 Ejezeeijm A 30 Company names and product names are trademarks or registered trademarks of their respective holders Copyright O 2008 2010 Roland DG Corporation http www rolanddg com N To Ensure Safe Use Improper handling or operation of this machine may result in injury or damage to property Points which must be observed to prevent such injury or damage are described as follows About A WARNING and CAUTION Notices Used for instructions intended to alert the user to the risk of death or severe NWARNING injury should the unit be used improperly Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly NCAUTION Material damage refers to damage or other adverse effects caused with respect to the home and all its furnishings as well to domestic animals or pets About the Symbols The A symbol alerts the user to important instructions or warning
13. bles in place Bundle excess cable into the large cable clamp If you re using a PRO II PRO II V series or SP series except SP 540i and 300i printer this cable connection is not necessary Place the AC adapter at the location shown in the figure and connect it to the AC adapter jack Connect the power cord Affix a small cable clamp at the location shown in the figure and secure the power cord in place Printer connection jack Cable clamp large Printer connector cable After connecting this cable connect the AC adapter Cable clamp small Cable clamp small ian Printer connector 1 z 3 2 ji Place inside the control box AC adaptor jack Electrical outlet 19 4 Operation Operating Conditions for the Take up Unit Never pull the media with excessive force Pulling the media with excessive force may actuate the protective feature and result in an error To avoid pulling the media with excessive force be sure to observe the following points O Never operate the MANUAL switch for the take up unit when the loading lever is engaged low ered O Never use the cursor key 4 to feed the media in reverse If the printer is provided with a cutting feature be sure to observe the following points as well These are all intended to avoid pulling the media with excessive force O Never perform cutting operations O
14. ck or injury Entrust repairs to a trained service technician Conduct operations in a clean brightly lit location Working in a location that is dark or cluttered may lead to an accident such as becoming caught in the machine as the result of an in advertent stumble 9 QD 9 Never climb or lean on the machine The machine is not made to support a per son Climbing or leaning on the machine may dislodge components and cause a slip or fall resulting in injury A To Ensure Safe Use AN Danger of electrical short shock electrocution or fire Z WARNING NWARNING Connect to an electrical outlet that com plies with this machine s ratings for volt age frequency and current Incorrect voltage or insufficient current may cause fire or electrical shock Ratings S Never use out of doors or in any location where exposure to water or high humidity may occur Never touch with wet hands Doing so may result in fire or electrical shock Never allow any foreign object to get inside Never expose to liquid spills Inserting objects such as coins or matches or allowing beverages to be spilled into the ventilation ports may result in fire or electrical shock If anything gets inside immediately disconnect the power cord and contact your authorized Roland DG Corp dealer Never place any flammable object nearby Never use a combustible aerosol spray nearby Never use in any location wh
15. d the screen shown in the figure appears Q Pull the dancer roller back toward you then make sure the media is stretched taut and press The screen shown in the figure appears CHECK TAKE UP SETTING J Take up the media O Make the setting for the AUTO switch on the take up unit Take up with outward curl AUTO MAN BACKWARD BACI OFF l FORWARD FOR a 9 Take up with inward curl AUTO MAN f BACKWARD BACI FORWARD FOR O 23 4 Operation Press The screen shown in the figure appears When you begin take up take care to ensure that the end of the media does not become rolled or creased This completes loading of the media PRO II PRO II V series SP series except SP 540i and 300i I Pass the media through the printer O e SET UP Steadily lighted refer to the user s manual for the printer OK Not OK Move the dancer roller toward the rear Load roll media onto the printer and put the printer in the setup state so that is illuminated For information on how to perform loading After loading check the following points O The media is loaded straight O All areas of the media are taut If
16. ere gases can accumulate Combustion or explosion may be a danger Handle the power cord plug and electrical outlet correctly and with care Never use any article that is damaged Using a damaged article may result in fire or electrical shock When using an extension cord or power strip use one that adequately satisfies the machine s ratings for voltage frequency and current Use of multiple electrical loads on a single electrical outlet or of a lengthy extension cord may cause fire Position so that the power plug is within immediate reach at all times This is to enable quick disconnection of the power plug in the event of an emergency Install the machine next to an electrical outlet Also provide enough empty space to allow immediate access to the electrical outlet If sparking smoke burning odor unusu al sound or abnormal operation occurs immediately unplug the power cord Never use if any component is damaged Continuing to use the machine may result in fire electrical shock or injury Contact your authorized Roland DG Corp dealer A To Ensure Safe Use A Important notes about the power cord plug and electrical outlet Never place any object on top or subject to Never allow to get wet damage b A Y 7 ZH Never bend or twist with undue force Never make hot Dust may cause fire Never bundle bind or roll up Important Notes on Handling and Use This machine is a
17. ing this unit select TU2 accompanying the pull back operation or TU not accompanying the pull back operation RS 640 540 VP 540i 300i SP 540i 300i O At the SETUP SHEET screen selecting either ROLL or TU is now possible When performing printing using this unit select TU 1 Getting Started Part Names and Functions MANUAL switch You use this when you want to operate the take up unit manu Arm Dancer roller Control box ally This is used to mount the This maintains uniform This controls take paper tube for take up tension for media up of the media AUTO MiNUAL BACKWARD BA KWARD FORW RD FORWARD AUTO switch This makes the direction of rotation for take up during printing change automati cally O IN S End caps ota Here is where you Printer connector e mount the paper tube This connector is used for mak for taking up media ing the connection when using the o i printer connector cable included with the unit i Clee I 1 AC Adapter Jack t l Here is where you connect the e included dedicated AC adapter About the Notation Used in This Manual This document uses the following images to indicate the keys and lights on the printer s operation panel Ca JC Y JC x JC Cursor keys SETUP key light ENTER key BASE POI
18. mall bolts wrench the stand log Hex Mz small GE ux fixture C Frame Control box P Press against the stand leg re Bolts with fixture A wasn ee Hex wrench Mounting small Hex wrench fixture B small Small bolt Bolt with washer HH cm L Mounting fixture A Mounting fixture B 15 3 Assembling and Installing Other Models VS series RS series VP series SP 300V 300 SP 540i 300i etc ARES Press against 9 Small bolts T Hex wrench Press against Mounting 7 the stand leg pn eae ie atend led EE Pp Ax p 7 4 E Small bolts y 2 Do b lt AA Bolts with Control box i N washer L e Hex wrench Cu small ing fi Mountin Fans Mounting fixture C e B Hex wrench small Small bolt Bolt with Ls washer Mounting Mounting fixture A fixture B After securing in place hold the unit atthe locations shown in the figure apply gentle pressure and make sure the assembly is free of looseness If looseness is present again press the take up unit against the stand leg and caster and tighten the small bolts 16 3 Attach the dancer roller and mount the paper tube Attach the dancer roller Working from the right side first secure in place 3 Assembling and Installing Dancer roller bolt hole and secure in place oF
19. ndling and Use eese enne nennen nnn nnne nnn nnns 6 WETT 7 aucune EM 8 EXHI IM 8 Main Compatible Models As of September 2010 ssssssssscsssscsssseccsuseccssecessusecssusessuseessuscessnseessuseessuecessnsecssneeseenseessnees 8 Changes in Printer Functioning ssec crore rotten terit onde tecta rteeteoeve ede eue Hebraea Habeo res eU PH Qu ree OPER stu GUERRE RUD 8 Part Names and FUMCHOMS cscsssssciaiseccocsdesacoceasssoosstenssooctninseossdodissecenssseoestoasssdesnsaseosddodud issivaveccstounssstetnassecdtodnssaeebnnssaaitdoasnabdtonns 9 2 Checking the Included Items te eto eere le aere roa et an 10 3 Assembling and Installitg 3 is 12 hc rurdidipiee c 12 Assembling and Installing ee eh In 12 A Operation p E 20 Operating Conditions for the Take up Unit unesseesssensssssunsssennsssenussenunsssunnsssnnnsssennsssnnnssennnnssennnssnensssnnnnsssnnnsssanessennne 20 Abo t th amp Paper Ule 20 Howto Load Lee 21 To Take up Media Manual Visca inc tutore rire aa i cera rese reed ehe pneu 27 How to Remove Taken up MeCia ssssssssssssssccsssessesssssssseesssessessnsessssesnsessersssesessesnsesserssneeseesnsesseresnesssesnsesserennereesesnseeessess 28 5 Whatto do Muscari H PM 29 The take up unit doesn t take up MECI
20. precision device To ensure the full performance of this machine be sure to observe the following important points Failure to observe these may not only result in loss of performance but may also cause malfunction or breakdown This Machine Is a Precision Device O Handle carefully and never subject the machine to impact or excessive force O Never cover the ventilation holes with cloth tape or anything else User s Manual 1 Getting Started System Features O This is a take up unit for large format printers from Roland DG Corp O This unit automatically takes up media as it is being printed This enables lengthy output and unattended operation at night to be accomplished efficiently O Media weighing up to 30 kilograms can be used Stable take up is possible even for heavy media If the printer s usable media weight is less than 30 kilograms media weighing more than this cannot be used Main Compatible Models As of September 2010 O PRO II PRO II V series including SOLJET PRO II V series SOLJET PRO II series Hi Fi JET PRO II series CAMM JET PRO II series O VersaCAMM series including VS series VP series SP series O VersaArt series including RS series Changes in Printer Functioning Installing this unit changes the printer s menus and other behavior in the following ways VS 640 540 420 300 O At the SETUP SHEET screen selecting whichever ROLL TU or TU2 is now possible When performing printing us
21. s The specific mean ing of the symbol is determined by the design contained within the triangle The symbol at left means danger of electrocution The symbol alerts the user to items that must never be carried out are forbidden The specific thing that must not be done is indicated by the design contained within the circle The symbol at left means the unit must never be disassembled The symbol alerts the user to things that must be carried out The specific thing that must be done is indicated by the design contained within the circle The symbol at left means the power cord plug must be unplugged from the outlet A Media weighs 30 kg 66 Ib Z WARNING NWARNING Handling roll media is an operation that When storing roll media implement ad D must be performed by two persons or equate safety measures to ensure that the more and care must be taken to prevent stored media will not roll fall or topple falls over Attempting to lift heavy media in a manner Danger exists of becoming pinned under the that taxes your strength may cause physical media and suffering serious injury injury A To Ensure Safe Use A Incorrect operation may cause injury NWARNING NCAUTION Be sure to follow the operation procedures described in this documentation Never allow anyone unfamiliar with the usage or handling of the machine to touch it Incorrect usage or handling may lead to an accident A Exerci
22. se caution to avoid being pinched or becoming caught Inadvertent contact with certain areas may cause the hand or fingers to be pinched or become caught Use care when performing operations Keep children away from the machine The machine includes areas and components that pose a hazard to children and may result in injury blindness choking or other serious accident Never attempt operation while wearing a necktie necklace or loose clothing Bind long hair securely Such items may become caught in the ma chine resulting in injury Never operate the machine while tired or after ingesting alcohol or any medication Operation requires unimpaired judgment Im paired judgment may result in an accident Never use the machine for any purpose for which it is not intended or use the machine in an undue manner that exceeds its capacity Doing so may result in injury or fire For accessories optional and consumable items AC adapter power cord and the like use only genuine articles compatible with this machine Incompatible items may lead to an accident Before attempting cleaning maintenance or attachment or detachment of optional items disconnect the power cord Attempting such operations while the machine is connected to a power source may result in injury or electrical shock o e e ooo e Never attempt to disassemble repair or modify the machine Doing so may result in fire electrical sho
23. ssthan 1 371 Less than 1 071 Less than 762 mm 74 in mm 64 in mm 54 in mm 42 in mm 30 in Acceptable media weights Maximum 30 kg man 26 5 k 25k 22k 205k 185k Sud eae box 58 4 Ib 551 Ib 48 5 1b 45 2 Ib 408 Ib Power Dedicated AC adapter AC 100 to 240 V 10 50 60 Hz requirements Machine DC 19V 21A Power consumption Approx 20 W Acoustic noise level 64 dB A or less Environmental Temperature 5 to 40 C 41 to 104 F humidity 20 to 80 RH non condensing NOTE The actual usable media weight may depend on the printer s conditions for usable media 30 31 32
24. tach the frame and control box to the support bar Control box A qu A bar y gt pate Narrow Frame Hex wrench Large bolt sI large i Large bolts A 4 pcs Attach the arm to the rail slider and secure in place with the arm retaining screw Rail slider Orient this side toward the rear Arm retaining screw 12 3 Assembling and Installing Place the rail slider on the control box and the frame and secure it in place Line up the tab on the frame with the slot in the rail slider then use large bolts to secure it in place first to the control box and then to the frame Line up the tab with the slot Bottom surface of the rail slider Ais Hex wrench O 1 Slot l large Y Large bolt loe Slot O Lay the unit on its side oriented as shown in the figure then use large bolts to fasten the control box and the frame to the support bar Large bolts Hex wrench large Frame Support bar Control box Large bolts 3 Assembling and Installing 2 Secure the assembled take up unit in place on the printer stand O Check to make sure the screws on the printer stand are not loose Retighten if loose Place the take up unit on the stand Determine where to secure the take up unit in place 0 Secure mounting fixture A in place using bolts with washers The mounting location varies according to the
25. the media is slack or crooked cancel the setup state and reload the media Check to make sure the following setting menu items on the printer are each set to DIS 24 ABLE O The PREFEED setting menu item O The FEED FOR DRY setting menu item only on models where this setting is avail able For information on how to check or change setting values refer to the user s manual for the printer 4 Operation 2 Fasten the media to the paper tube Make sure is lighted then use CY to pull out the media until its leading edge reaches the paper tube Check to make sure the media is pulled out straight at this time If the media is not straight redo the loading operation OK Not OK 6 Using adhesive tape fasten the center and side edges of the media to the paper tube fasten a total of three locations Secure the center of the media in place while keeping the media stretched taut to keep it free of slack While pulling the media from the center outward fasten the left and right edges Take up with outward curl ii Paper tube Adhesive tape 25
Download Pdf Manuals
Related Search