User manual
Contents
1. board Carriage wheel assembly Power Supply Power failure backup batteries Tension wheel Qo et 20 End oo do ES 1 2 1 Motor The motor which is part of the drive unit drives the door leaves through a tooth belt The motor operates on 40V DC 1 2 2 Control board EDSL CU 450 The control board EDSL CU 450 is the central controller for the sliding door It receives information from the safety devices and motion detectors and operates the motor to open or close the door The control board is installed in the drive unit and is connected to The motor Encoder for position feedback Power supply Safety activators Back up battery Electrical lock optional External activation device optional Push buttons intercom installation optional 1 3 Safety System The safety system opens or closes the door in case of emergency The safety system consists of Panic button Safety sensors Emergency battery back up Fire alarm optional 1 4 Activation The different types of optional activators are Radar motion detection Active infrared motion and or presence detection Key switch manual Push button manual Hand transmitters Etc The activators give an impulse to open or close the door The radar and active infrared activators are installed close to or on the drive unit The other activators can be installed in other positions and are not necessarily in proximity to the drive unit 1 5 Program sel2. 1 Checklist before you contact your local service provider esee Declaration of incorporation Revision information Date Revision Description 21 08 2014 1 00 Initial publication 01 12 2014 1 10 Changed declaration About this manual All users and owners of the EDSL450 sliding door must read understand and abbey the information and instructions in this manual Failure to do so may result in damage to or failure of the equipment and possibly injury to persons This manual contains information and user instructions for a sliding door When information or instructions are applicable to all the methods of operation or models there are no operation types or model numbers in the title When information or information are applicable to specific methods of operation or models the applicable operation type or model names appear in the title Maintenance of your sliding door To ensure your sliding door continues to operate with maximum reliability safety and performance it is necessary to perform regular maintenance as specified in this user manual and in the logbook supplied with your sliding door This maintenance must be done by qualified service engineers trained to recognise possible problems and to replace parts that have a defined life expectancy Dismantling and disposal of the door operator Dismantling of the door or parts thereof may only be carried out by qualified personnel These tasks a
3. 6 Program selection and interactiON coconcococccncnccononooononnnnnnnnnnnnnnnnnnnnnnnononnnnnnnnnnnnnnnnnnnnnnnnnanannos 8 1 7 Program Select Nica 8 1 7 1 Program indicati n TET aa 9 1 7 2 Status Indica ore 9 1 7 3 Override pro c EOD ILI 9 1 7 4 Show error and warning COD iii ies 9 1 7 5 RES 10 1 7 6 Initialise door E 10 1 7 7 Warning and error COCGS ccccccccceesssessssecececeseeseaaaeeeecussecaaeseeeescusseaaaaaaaeseseessseseaaeas 10 Di MN TT 12 2 1 Safety symbols used in this manual cccconocococcnnnonononononacnnnnnnnnnnnnnnnnnnnnnnnnnon nono nnnnnnnncnnnna nnns 12 3 Op ratinelinstructions iii aa ga a Rev dus 13 3 1 Daily Procedures uenerit ec pad Sn Ie SEG O decada DUO NE nar te roug aereo dessa nada 13 3 1 1 Daily start procedure coccccnccononoonnnnnnnnononennnnnnnnnnnnnnnnnnnnnnnnnnnnr nn TE EEEE ESASEN aE rE Er Tasai 13 3 1 2 Daily Stop DrOCGdUFe accetto terrent hanc oed sactes as endete 13 3 1 3 Daily function check after start procedure cccccccnoocoooncnnnnnnnonnnnnnnnnoconanononnnnnnancnananenonnos 13 AL irap 14 4 1 Preventive maintenance schedule eese enne nnne nnne 14 4 2 Replacement schedule ite Ete a sees 14 4 3 Preventive maintenance procedures sss nennen nennen enne nnn nnns nnne 15 5 6 4 3 1 Clean the door Troubleshooting 5
4. Entrance Dynamics sliding door operator EDSL450 User manual Original instructions O All rights in and to this material are the sole property of Entrance Dynamics BV Copying scanning alterations or modifications are expressly forbidden without the prior written consent of Entrance Dynamics BV Rights reserved for changes without prior notice Table of contents Revision Information uu 4 About this manlal t assassina pass sita dt iii iia 5 Maintenance of your sliding door ccscccccccecsssesssseseceeecesseseaeeeeeescsesesaeaesesesss cusseseaaeaeeeeeeesseseeaeeeseeseesees 5 Dismantling and disposal of the door operator o cccccccononoononcnnnnnonononnnnncnnnnnnanononnnnnnnnnnnnnrnnnnnnncnnannnns 5 Your local service provider cccccccsesscccececessesenesecececeseaeaeseeecesessesaeaeeesessecesecsaaaeseeeescesseeaseeeeeesesegs 5 Door leaf Scope Of delivery iis eet eae eost fade sa dee ean uos e ea denis de aain a 5 1 introductio cc 6 1 1 BNET 6 1 2 Bue H 6 1 2 1 ioo n 7 1 2 2 Control board EDSL CU 450 iecit detenti espe teo ed onn idosa bra o Range tane 7 1 3 CERA LIMES T 7 1 4 pedido p 7 1 5 Program Selector ec dass 8 1
5. Red blinking Door controller is in error state Errors can be reset with the program switch retry Orange pulsing Door controller is in service mode Service mode cannot be altered with the program switch 1 7 3 Override program The program used by the door controller can override the selection made with the program switch The indicator will always show the program selected if possible If the active program is different then the program selected with the switch the indicator will blink There are two possible methods to override the program with active inputs and temporary pulses The temporary override can be reset by selecting the active program After it has been selected the override is cancelled As a result the indicator will be lid continuously Afterwards the program can be changed by the program switch again 1 7 4 Show error and warning code If an error or warning is active on the controller the code can be shown on the program indicators A warning or error is indicated with a multi colour indicator next to the service symbol When the program switch is positioned in the service position the warning or error code will be shown Whether the shown code is a warning or error is determined by the status indicator The code is shown using all six program indicators including the service symbol Fout Verwijzingsbron niet gevonden shows the symbols and added labels for clarity The labels are used in the warning and error t
6. ables table and table Multiple warnings can be active simultaneously However only one warning will be shown The door controller determines what code will be shown 1 7 5 Reset error To reset the error the reset position must be selected for more than 1 second On selecting a program position the reset command is transmitted While the key switch is reset position the warning or error code is shown instead of the active program 1 7 6 Initialise door The door can be re initialised by selecting the reset position for more than 3 seconds but less than 8 seconds If the reset is selected more than 8 seconds no actions are performed but the warning or error code is shown instead of the active program 1 7 7 Warning and error codes 1 7 7 1 Table Warning codes A B C D E F Warning description eoooo0 O Service required Battery missing 000000 Sensor supply overload O Indicator is off o Indicator is on 10 1 7 7 2 Table Error codes A B C D E FF Error description 00000 Osu ly failure Current offset error O O O O Motor inverted while operational do Ca CO co 5 Cc e Ui ES NEN a a a DODGE qe CG ECE eee ae ge A oe Se ae ede 1 2 2 CRT 1 904 o ac SS KCEOW E M HET a e To eS ee a NEMINEM Mad RR OLD ES 11 2 Safety 2 1 Safety symbols used in this manual The following safety symbols are used in this manual Indicates a general warning e Only aut
7. ct keeps its functionality safety and classification It keeps the warranty valid and prevents unexpected and expensive breakdowns or accidents The following list contains the recommended replacement frequencies Frequency Tasks Every year or 100 000 openings Replace the floor guide Every 3 years or 250 000 openings Replace the backup batteries Replace the replaceable part of the key switch Replace the mohair brush Replace the tooth belt 14 Every 4 years or 500 000 openings Replace the carriage wheels Replace the wheel track Replace the anti derailment wheels Every 7 years or 750 000 openings Replace the drive unit Replace the electric lock The economic life time of the products is on normal use and in a normal environment estimated on 10 years or 1 000 000 cycles Therefore after 10 years or 1 000 000 cycles a major overhaul has to be executed in order to extend the life time and ensure a safe and reliable function The following items have to be considered for replacement e Hook lock e Combined Radars Sensors e Safety devices e Other activators e Control unit e Program switch e Emergency button 4 3 Preventive maintenance procedures 4 3 1 Clean the door Do not use the door leaf or Drive unit to support a ladder when you do maintenance on a door Always use ladders as specified in local health and safety instructions Do not use a high pressure washer to clean the door Do the Daily Stop proced
8. ector switch The Program switch is used to select the required program The program switch can be installed close to the door or at another location in the building 1 6 Program selection and interaction The program switch is used to select the program that will be used for the sliding door 1 7 Program selection Selection is done with a key switch The switch can be positioned in six different positions five of which are programs and one is used for error reporting and reset position F See the table below for the list of programs that can be selected To prevent multiple changes to the selected program while switching from one to another the switch has to remain stationary for more than two seconds before the new program is activated Position A EEE EE L Function Program close Door is closed and locked Sensors will not open the door Only porter input can be used to open the door Program exit only full open Door opens on activation of inside motion sensor An open door will remain open if either inside or outside presence sensor is active Door is opened to the full open position Program automatic full open The door will open on activation of all sensors inside or outside Door is opened to full open position Program automatic reduced open The door will open on activation of all sensors inside or outside Open position will be to the reduced open position or full open position depending on
9. horized persons are permitted to operate the door e Read and fully understand the safety instructions before you operate or do maintenance on the door e Always obey local health and safety regulations when you operate or do maintenance on the door e Make sure there are no persons or equipment in the working area of the door before you operate the door e Donotremove or immobilize safety equipment installed on or near the door e Do not operate the door if it has any defects Report defects to the supervisor immediately e Do not operate the door after the date of the next scheduled maintenance The date of the next scheduled maintenance is shown in the logbook e Donot modify the door Unauthorized modification can cause danger to people and affect the function and safety of the door 12 3 Operating instructions 3 1 Daily Procedures 3 1 1 Daily start procedure e Visually check the door for damage e Ifdamage is found o Apply suitable warning signs around the door and on the door leaves o Contact your local service provider e f no damage is found o Set program selector to the required position 3 1 2 Daily stop procedure e Examine the door for damage e f damage is found o Apply suitable warning signs around the door and on the door leaves o Contact your local service provider e f no damage is found o If the door is in an escape route and or the only entrance make sure that no person is in the building o Se
10. re complicated and potentially dangerous Please make a contribution to protecting the environment when disposing of the door at the end of its functional life Contact your local authorised service provider for appropriate means of disposal Your local service provider It is recommended that you contact your local authorised Entrance Dynamics service provider for details about service agreements available for your sliding door Door leaf Scope of delivery The door leaves are produced by third parties in accordance with specifications as approved by Entrance Dynamics However they are not included in the scope of delivery 1 Introduction The sliding door is designed to enable easy access to and from buildings or between building sections The sliding door has 3 primary parts 1 Door leaves 2 Drive unit 3 Activators Safety sensors 1 1 Door Leaves The door leaves are usually made of glass and surrounded by profiles made of aluminium Brush profiles are installed on the door leaves to reduce draft The door leaves are suspended from the carriage wheels The door adapter profile connects to the carriage wheels and the door leaves The bottom of the door leaves are kept in position by the floor guides 1 2 Drive unit The drive unit opens and closes the sliding door The door leaves are connected to the drive unit via the carriage wheel brackets The drive unit consists of Mounting profile Motor Tooth belt Control
11. s declared that final installed automatic door system has been subject to a risk assessment in compliance with Machinery Directive 2006 42 EC The manufacturing process ensures the compliance of the equipment with the technical file and is regularly accessed by 3 party 17
12. sure the inside and outside sensors are clean and free of obstructions Make sure the safety sensors are clean and free of obstructions Make sure the photocells are clean Make sure bottom guides are running freely Perform reset on the program switch 16 6 Declaration of incorporation We Entrance Dynamics B V Breeuwhamer 6 1648 HG De Goorn Netherlands Declare under our sole responsibility that the type of equipment Sliding door operator type EDSL450 Sliding door retrofit kit type EDSL450 Is in compliance with the following directives 2006 95 EC Low Voltage Directive 2004 108 EC ElectroMagnetic Compatibility Directive EMCD 2006 42 EC Machinery Directive MD with the following essential health and safety requirements 1 1 2 1 2 1 1 2 2 1 2 3 1 2 4 2 1 2 6 1 3 9 1 4 3 1 7 2 1 7 4 1 7 4 1 1 7 4 2 2002 95 EC Restriction of Hazardous Substances RoHS Technical documentation for safe integration is provided Harmonized European standards which have been applied EN 60335 1 EN 61000 6 2 EN 61000 6 3 EN ISO 13849 1 Other standards or technical specifications which have been applied DIN 18650 1 2 EN 60335 2 103 EC type examination or certificate issued by notified body IFT 0757 No 14 000152 PB01 SP 0402 No SC0707 14 for full address please contact Entrance Dynamics B V EN 16005 The equipment must not be used until the installation organisation by issuing a Declaration of Conformity ha
13. the activator This program cannot be used in escape routes Program open full open Door opens and remains open during this program regardless of sensors active Error reporting and reset When the controller has a warning or is in error placing the switch in this position will cause program switch to display the warning or error code Program change may not be possible if the program is overridden in the door controller For added security the key can be removed from the switch when positioned in any position except the reset position F 1 7 1 Program indication The active program of the door controller is presented with an indicator If the program switch is at that program the indicator lights continues If the program selection of the switch is overridden then the indicator will blink If a program is active that the program switch is not capable of displaying or during loss of communication to the controller the program switch will rotate the program selection indicators as the indication that no program can be displayed 1 7 2 Status indication Next to the service symbol is a multi colour indicator for status information such as warning and error Status indicator colours Colour Description Green Ok no errors or warnings active Orange continuous Warnings present which may prevent the door from functioning correctly Some warnings can be reset with the program switch but most must be resolved otherwise
14. tthe program selector to the required position 3 1 3 Daily function check after start procedure e Approach the door from both sides and make sure the door opens and closes e If the door does not operate correctly contact your local service provider 13 4 Maintenance According to the EN16005 DIN18650 and AutSchR for escape routes the installer retains responsibility for the safe operation of the sliding door only when user instructions are obeyed and the service checklist and scheduled maintenance tasks are done by authorised certified people If not the owner takes over all responsibility The owner is responsible that maintenance is carried out 4 1 Preventive maintenance schedule Fewwy mo qua Daily Door complete Do the daily start procedure Do the daily function check after start procedure Do the daily stop procedure Make sure the door leaves are clean but visible Make sure the door leaves are free of obstacles boxes goods etc Floor guides Make sure the leaves are guided properly and remove any debris from floor track follow the local Door complete Annual inspection made by authorised regulations but not Service Partner less as every 12 months 4 2 Replacement schedule Apart from regulatory maintenance we at Entrance Dynamics think it is important for our doors to be treated the same way as a vehicle change the oil and the tires at the correct time With preventive replacement you make sure the produ
15. ure Use a soft clean brush and mild detergent to clean the inside and outside of the door leaf Use a soft clean brush and mild detergent to clean the outside of the Radars Sensors Photocells If damage is found contact your local service provider for repairs cues 15 5 Troubleshooting This chapter contains troubleshooting information for the user of an automatic sliding door If a fault is not described below contact your local service provider for assistance Symptom Door does not open Door does not close Cause No power Program Selector in close position Object detected by Sensor Radar No power Program Selector in open position Solution Make sure the main switch and fuse are serviceable Switch the power supply on Select program selector to the automatic position Do the daily start procedure Move the object outside the detection area Make sure the main switch and fuse are serviceable Switch the power supply on Change the position on the program selector If it is necessary to adjust the opening or closing speed or the sensitivity or detection field of sensors please contact your local service provider 5 1 Checklist before you contact your local service provider Make sure the main electrical power supply is on Make sure the program switch is in the correct position Make sure there are no obstacles beside under or between the door leaves Make
Download Pdf Manuals
Related Search