TEF 2440 LED
Contents
1. MANUAL COMPLETE THE INSTALLATION Before replacing the globe assembly please review the following e Verify that the grommet kit used match the cable diameter e Cables should have a bend downwards before entering the cable gland which will avoid water intrusion into the luminaire e An unused cable gland should be replaced with a blind plug The safety wire should be in place and the two electrical wires for power to the LED s should be correctly positioned and The input power 120 or 230 VAC should be terminated as indicated inside the lamp For the 24VAC VDC version connect power to the connection block Ensure the globe gasket is clean and properly aligned around the bottom of the globe assembly Carefully position the globe onto the lamp body and ensure that no wires come between the lamp body and the globe assembly Place the globe ring over the globe and ensure the four screws enter the recessed nuts in the lamp body Slightly tighten two opposite screws then repeat with the other two opposite screws This ensures that the globe is positioned evenly and the pressure on the globe gasket is distributed evenly Tighten all four screws until the globe is firmly positioned Power tools should under no circumstances be used n Z ee Ke2. 146 r m T 120 a I an i gt T F F h i mc a S T i in 7 J 100 140 Fi Ei J a A a l T Y o A lT a lL 4 pcs amp 6 TEF 2440 LED LUMINAIRE USER gt MANUAL SPARE PARTS Description Part No Complete low globe assembly green 4528 Complete high globe assembly red 4417 Complete fastening ring 4249 LED driver 230VAC 5086 0079 LED driver 120VAC 5086 0089 LED driver 24VAC VDC 4399 Globe gasket silicon 5001 0021 Complete connection assembly 4246 Cable gland E704 CD M25 9147 200 Stopping plug M25 EExe L 9 7947 304 TECHNICAL DATA Material Acid proof stainless steel powder coated RAL 9010 Globe Polycarbonate lexan Input voltage 24 VAC VDC 120 VAC 50 60Hz 230 VAC 50 60Hz Light output Red gt 32 Candela Green gt 30 Candela Power comsumption Max 10W IP rating IP66 Standard cable entries 1 x M25 stopping plug 1 x M25 cable gland For use in zone Safe area Height Red 240 mm Green 147 mm Width 140 mm Length 164 mm Weight Red 2 0 kg Green 1 9 kg TRANBERG Tranberg AS PO Box 8033 N 4068 Stavanger Norway Tel 47 51 57 89 00 Fa
3. TEF 2440 LED PERIMETER LIGHT OBSTRUCTION LIGHT USER MANUAL IMPORTANT Read this instruction carefully before installing the product TRANBERG Tranberg AS P O Box 8033 N 4068 Stavanger Norway Tel 47 51 57 89 00 Fax 47 51 57 89 50 E mail info tranberg com www tranberg com Tranberg Systems Hjulmagervej 15C 7100 Vejle Denmark Tel 45 75 85 83 80 E mail mail tranbergsystems com www tranbergsystems com TUM 1072 04 03 11 TEF 2440 LED LUMINAIRE USER MANUAL INTRODUCTION TOOLS REQUIRED Thank you for purchasing this product Regular tools required for installation For installation maintenance and assurance of a long life e 10mm wrench whien installing the luminaire of this product please follow this manual e 32mm wrench whien installing the cable gland e 30mm wrench when installing the lock nut APPLICATIONS e 25mm wrench when tightening the pressure nut e PZ 2 screwdriver for assemble dissemble the globe e Perimeter light for helideck landing areas e 3 mm straight screwdriver for terminal to connect the e Signal lighting lighting e Obstacle marking e 5mm straight screwdriver for earth screw Do not use powertools when fastening globe CONTENT IN BOX The product is fully assembled and ready for installation SAFETY PRECAUTIONS MAINTENANCE INSTRUCTIONS Note that changes made to the product and or installation The luminaire should be inspected accord
4. ing to Company of components which do not conform to the approval may routines The manufacturer suggests regular check for be a safety violation The manufacturer will in no water intrusion condensation which should be removed circumstance be held responsible for such activity immediately When cleaning use only mild detergents For your health and safety always use safety gear suited Alcohol or petroleum based products may damage lens for the task Be certain to follow codes regulations and or paint or plastic components specific procedures that are related to the installation RUBBER SEAL Cable diameter Size Part No 8 5 13 5mm 23 13x8mm 5002 0124 13 17mm Q23 16x8mm 5002 0125 Be sure to install cable in a way wich prevents water to penetrate into the enclosure through the cable gland also make sure to use the correct rubber seal when you install the luminaire ELECTRICAL INSTALLATION The luminaire is factory configured with grommet kit 3C suitable for cable diameters ranging from 8 5 mm to 13 5 mm For cable diameters ranging from 13 0 mm to 17 0 mm please ensure to replace the installed grommet kit with kit 3D for thinner cables ask your supplier which grommet kits to be used Cable entries should be tightened properly Do not use excessive force as this may disalign the grommet components and lead to water intrusion Make sure electrical connections are safe and reliable TEF 2440 LED LUMINAIRE USER
5. x 47 51 57 89 50 E mail info tranberg com www tranberg com Tranberg Systems Hjulmagervej 15C 7100 Vejle Denmark Tel 45 75 85 83 80 E mail mail tranbergsystems com www tranbergsystems com
Download Pdf Manuals
Related Search