User Manual - Kramer Electronics
Contents
1. 6 2 Wiring the RS 232 Connector 12 45 78 36 Prepare an RS 232 cable with a 9 pin D sub connector at one end and a 2 pin terminal block connector at the other end as defined in Figure 5 RS 232 to TP 210A PIN 5 Connected to G PIN 3 Connected to Rx PC 9 pin D sub TP 210A to Controlled Unit G Connected to PIN 5 Tx Connected to PIN 2 9 pin D sub Figure 5 RS 232 PINOUT Connection 10 KRAMER SIMPLE CREATIVE TECHNOLOGY Technical Specifications 7 Technical Specifications Table 4 includes the technical specifications of the TP 210A Table 4 Technical Specifications of the TP 210A INPUTS 1 UXGA video on a 15 pin HD connector 1 unbalanced stereo audio on a 3 5mm mini jack 1 S PDIF on an RCA connector 1 RS 232 with 1 RxD line on a terminal block connector OUTPUTS 10 twisted pairs on RJ 45 connectors 2 UXGA on 15 pin HD connectors 2 unbalanced stereo audio on 3 5mm mini jacks 2 S PDIF on RCA connectors 2 RS 232 with 2 TxD lines on terminal block connectors MAX OUTPUT LEVEL Video 1 6V Audio 2 3V POWER OUTPUTS 12V DC 0 5A max via each RJ 45 output PINs 4 5 RESOLUTION UXGA amp 1080p BANDWIDTH 20Hz to 20kHz 19 audio SAMPLING RATE FOR S PDIF 48kHz S N RATIO AUDIO gt 75dB TOTAL GAIN AUDIO Analog analog 0dB Analog SPDIF 12dBFS TND N AUDIO lt 0 02 POWER SOURCE 100 240V AC 50 60 Hz 46VA DIMENSI2. 1 Getting Started 2 4 Quick Start The quick start chart summarizes the basic setup and operation steps of the TP 210A Step 1 Mount the machine see section 5 Mount the machine in a rack or stick the 4 rubber feet to the underside 4 Connect a computer graphics source to the UXGA input an audio source to the audio input and RS 232 to the G port Connect the UXGA 1 video and audio outputs and the RS 232 port if required Connect the UXGA 2 video and audio outputs and the R5 222 port if required 4 Connect to up to 10 TP 124 receivers via CAT 5 to 300ft 10d Peters meters 124 STP Cable Plasma Display Computer Graphics Audio RS 232 Control Step 3 Set the underside switches see section 6 NEG Set the Hs and Vs polarity switches Vs Hs NORM Step 4 Connect the power 2 KRAMER SIMPLE CREATIVE TECHNOLOGY Overview 3 1 Overview The TP 210A UXGA Audio RS 232 Line Transmitter DA receives a computer graphics signal an audio signal and an RS 232 signal and distributes them to up to 10 receivers via CAT 5 cables The TP 210A also simultaneously distributes the signal to two UXGA outputs two analog audio outputs or two digital audio outputs and two RS 232 outputs The TP 210A serves as a power center that can distribute power to the connected receivers see section 3 1 In particular
3. Connect to the digital audio acceptor 10 RS 232 Terminal IN G Rx Connect the two connectors G and Rx to transmit a Block Connector command see section 6 1 11 OUT G Tx Connect the two connectors G and Tx to control a device see section 6 1 12 Power Connector with Fuse AC connector enabling power supply to the unit 4 1 The TP 210A UXGA Audio RS 232 Line Transmitter DA Underside Figure 2 and Table 2 define the underside of the TP 210A NEG vs NORM Figure 2 TP 210A Underside Table 2 Features of the TP 210A Underside Feature Function VS Switch Slide the switch up to set the VS to negative polarity NEG Slide the switch down to set the VS to its input polarity NORM HS Switch Slide the switch up to set the HS to negative polarity NEG Slide the switch down to set the HS to its input polarity NORM 1 From 1 to 2 2 Using a UTP CAT 5 cable with RJ 45 connectors at both ends the PINOUT is defined in Table 3 and Figure 4 3 For example the Kramer TP 124 or TP 46 4 RS 232 can be embedded only when the S PDIF ANALOG Selector Button is set to the analog state 5 By default both switches are set to NORM KRAMER SIMPLE CREATIVE TECHNOLOGY Installing on a Rack Installing on a Rack This section provides instructions for rack mounting the unit Before Installing in a Rack Before installing in a rack be sure that the environment is w
4. OUT 1 3 5mm mini jack connector to the analog audio connector on the acceptor If required connect the RS 232 G and TX1 terminal block connector to the RS 232 port on the acceptor 5 Connectthe UXGA OUT 2 15 pin HD connector to a UXGA acceptor for example a display and the ANALOG AUDIO OUT 2 3 5mm mini jack connector to the analog audio acceptor for example an AV Receiver 6 Connect the LINE OUTPUT CAT 5 connectors as follows The LINE OUT 1 RJ 45 connector on the TP 210A to the LINE IN RJ 45 connector on a TP 124 unit via UTP cabling with a range of up to 300ft up to 100m The LINE OUT 10 RJ 45 connector on the TP 210A to the LINE IN RJ 45 connector on another TP 124 via UTP cabling with a range of up to 300ft up to 100m 1 Switch OFF the power on each device before connecting it to your TP 210A After connecting your TP 210A switch on its power and then switch on the power on each device 2 Alternatively you can connect a digital audio source and acceptors and release the S PDIF ANALOG selector button 3 Not supplied The full list of Kramer cables is on our Web site at http www kramerelectronics com You can also connect a UXGA source to the UXGA IN 15 pin HD connector and a separate audio source to the AUDIO IN 3 5mm mini jack 4 You do not have to connect all the outputs 5 Refer to the separate user manual which can be downloaded at http www kramerelectronics com 6 For details of how to wir
5. of this warranty EXCLUSION OFDAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for 1 Damage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or 2 Any other damages whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior approval This may be obtained from your dealer This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and light industry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and light industry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart Unintentional radiators CAUTION BO Servicing the machines can only be done by an authorized Kramer technician Any user who makes changes or modif
6. still suitable for the video audio transmission but not for feeding the power at these distances Your TP 210A UXGA Audio RS 232 Line Transmitter DA 3 2 3 3 Shielded Twisted Pair STP Unshielded Twisted Pair UTP We recommend that you use Shielded Twisted Pair STP cable There are different levels of STP cable available and we advise you to use the best quality STP cable that you can afford Our non skew free cable Kramer BC STP is intended for analog signals where skewing is not an issue For cases where there is skewing our UTP skew free cable Kramer BC XTP may be used Bear in mind though that we advise using STP cables where possible since the compliance to electromagnetic interference was tested using those cables Although Unshielded Twisted Pair UTP cable might be preferred for long range applications the UTP cable should be installed far away from electric cables motors and so on which are prone to create electrical interference However since the use of UTP cable might cause inconformity to electromagnetic standards Kramer does not commit to meeting the standard with UTP cable Recommendations for Achieving the Best Performance To achieve the best performance Use only good quality connection cables to avoid interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Avoid interference from neighboring electri
7. Kramer Electronics Ltd USER MANUAL Model TP 210A UXGA Audio RS 232 Line Transmitter DA Contents Contents 1 Introduction 2 Getting Started 2 1 Quick Start 3 Overview 3 1 About the Power Connect Feature 3 2 Shielded Twisted Pair STP Unshielded Twisted Pair UTP 3 3 Recommendations for Achieving the Best Performance 4 Your TP 210A UXGA Audio RS 232 Line Transmitter DA 4 1 The TP 210A UXGA Audio RS 232 Line Transmitter DA Underside 5 Installing on a Rack 6 Connecting the TP 210A 6 1 Wiring the CAT 5 LINE IN LINE OUT RJ 45 Connectors 6 2 Wiring the RS 232 Connector 7 Technical Specifications Figures Figure 1 TP 210A UXGA Audio RS 232 Line Transmitter DA Figure 2 TP 210A Underside Figure 3 Connecting the TP 210A UXGA Audio RS 232 Line Transmitter DA Figure 4 CAT 5 PINOUT Figure 5 RS 232 PINOUT Connection Tables Table 1 TP 210A UXGA Audio RS 232 Line Transmitter DA Features Table 2 Features of the TP 210A Underside Table 3 CAT 5 PINOUT Table 4 Technical Specifications of the TP 210A CAN ADAH FKWW YN p p CO QO o0 t 10 11 Introduction 1 Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentation and broadcasting professional on a daily basis In recent
8. ONS 19 x 9 3 x 1U W D H rack mountable WEIGHT 3kg 6 6lbs approx ACCESSORIES Power cord rack ears 1 Specifications are subject to change without notice 2 We recommend that you use only the power cord that is supplied with this machine 11 LIMITED WARRANTY Kramer Electronics hereafter Kramer warrants this product free from defects in material and workmanship under the following terms HOWLONGIS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase WHOIS PROTECTED Only the first purchase customer may enforce this warranty WHATIS COVERED AND WHATISNOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty 1 Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kramer at one of the agents listed in the Web site www kramerelectronics com 2 Any product on which the serial number has been defaced modified or removed or on which the WARRANTY VOID IF TAMPERED sticker has been torn reattached removed or otherwise interfered with 3 Damage deterioration or malfunction resulting from i Accident misuse abuse neglect fire water lightning or other acts of nature ii Product modification or failure to follow instructions s
9. ack rails and insert the proper screws not provided through each of the four holes in the rack ears Note e In some models the front panel may feature built in rack ears e Detachable rack ears can be removed for desktop use e Always mount the machine in the rack before you attach any cables or connect the machine to the power e If you are using a Kramer rack adapter kit for a machine that is not 19 see the Rack Adapters user manual for installation instructions available from http www kramerelectronics com Connecting the TP 210A 6 Connecting the TP 210A This section describes how to connect the TP 210A see section 6 wire the CAT 5 LINE OUT RJ 45 Connectors see section 6 1 and wire the RS 232 connectors see section 6 1 To connect the TP 210A as illustrated in Figure 3 do the following 1 Connect a UXGA source for example a laptop s graphics card to the UXGA INPUT 15 pin HD connector 2 Connect an analog audio source to the Audio IN 3 5mm mini jack for example using a Kramer C GMA GMA cable VGA 15 pin HD Audio jack to VGA 15 pin HD Audio jack and press the S PDIF ANALOG selector button 3 Connect an RS 232 cable with a 9 pin D sub connector at one end to the laptop and a 2 pin terminal block connector at the other end to the RS 232 IN port G Rx 4 Connect the UXGA OUT 1 15 pin HD connector to the UXGA acceptor for example a plasma display and the ANALOG AUDIO
10. cal appliances that may adversely influence signal quality and position your Kramer TP 210A away from moisture excessive sunlight and dust Your TP 210A UXGA Audio RS 232 Line Transmitter DA Figure 1 and Table 1 define the TP 210A 1 Available from Kramer Electronics on our Web site at http www kramerelectronics com KRAMER SIMPLE CREATIVE TECHNOLOGY Your TP 210A UXGA Audio RS 232 Line Transmitter DA LINE OUTPUTS ANALOG AUDIO soir OUT1 OUT2 OUT3 OUT4 OUTS OUT7 OUT 10 INPUT Our 1 2 JL Anos Figure 1 TP 210A UXGA Audio RS 232 Line Transmitter DA Your TP 210A UXGA Audio RS 232 Line Transmitter DA Table 1 TP 210A UXGA Audio RS 232 Line Transmitter DA Features Feature Function 1 POWER Switch Illuminated switch for turning the unit ON or OFF 2 UXGA INPUT 15 pin HD Connector Connect to the video source 3 UXGA OUT 15 pin HD Connectors Connect to the video acceptor 4 LINE OUTPUT RJ 45 Connectors Connect to the LINE IN RJ 45 connector on a receiver 5 ANALOG AUDIO INPUT Connect to the stereo analog audio source 6 35mm Mini Jacks our Connect the stereo analog audio acceptor 7 S PDIF ANALOG Selector Button Press to select the analog audio source Release to select the S PDIF source 8 S PDIF RCA INPUT Connect to the digital audio source 9 Connectors OUT
11. e a CAT 5 LINE IN LINE OUT RJ 45 connector see section 6 1 7 Alternatively you can connect the Kramer TP 46 which can be connected to an additional TP 46 unit for transmitting the signal further 8 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the TP 210A 7 Connect the power cord 8 If necessary set the HS and VS switches on the underside TP 210A Display Range up to 300ft up to 100 meters STP Cable Computer Graphics Plasma Plasma Audio RS 232 Display AV Receiver Display AV Receiver Control Figure 3 Connecting the TP 210A UXGA Audio RS 232 Line Transmitter DA 1 We recommend that you use only the power cord that is supplied with this machine 2 By default both switches are set down for normal V SYNC and H SYNC polarity 9 Connecting the TP 210A Table 3 and Figure 4 define the UTP CAT 5 PINOUT using a straight pin Figure 4 CAT 5 PINOUT 6 1 Wiring the CAT 5 LINE IN LINE OUT RJ 45 Connectors to pin cable with RJ 45 connectors Table 3 CAT 5 PINOUT EIA TIA 568A EIA TIA 568B PIN Wire Color PIN Wire Color 1 Green White 1 Orange White 2 Green 2 Orange 3 Orange White 3 Green White 4 Blue 4 Blue 5 Blue White 5 Blue White 6 Orange 6 Green 7 Brown White 7 Brown White 8 Brown 8 Brown Pair 1 4 5 Pair 1 4and5 Pair2 3and6 Pair 2 1and2 Pair3 1 2 Pair 3 3and6 Pair4 7 8 Pair 4 7 8
12. ications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment DO Use the supplied DC power supply to feed power to the machine DO Please use recommended interconnection cables to connect the machine to other components FCC and CE approved using STP cable for twisted pair products 12 KRAMER SIMPLE CREATIVE TECHNOLOGY For the latest information on our products and a list of Kramer distributors visit our Web site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Caution Safety Warning Disconnect the unit from the power supply before opening servicing P N 2900 000367 Rev 3 Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 000367 REV 3
13. ithin the recommended range range perature range CAUTION When installing on a 19 rack avoid hazards by taking care that 1 Itis located within the recommended environmental conditions as the operating ambient temperature of a closed or multi unit rack assembly may exceed the room ambient temperature 2 Once rack mounted enough air will still flow around the machine 3 The machine is placed straight in the correct horizontal position 4 You do not overload the circuit s When connecting the machine to the supply circuit overloading the circuits might have a detrimental effect on overcurrent protection and supply wiring Refer to the appropriate nameplate ratings for information For example for fuse replacement see the value printed on the product label 5 The machine is earthed grounded in a reliable way and is connected only to an electricity socket with grounding Pay particular attention to situations where electricity is supplied indirectly when the power cord is not plugged directly into the socket in the wall for example when using an extension cable or a power strip and that you use only the power cord that is supplied with the machine How to Rack Mount To rack mount a machine 1 Attach both ear brackets to the machine To do so remove the screws from each side of the machine 3 on each side and replace those screws through the ear brackets 2 Place the ears of the machine against the r
14. the TP 210A features e resolution of up to UXGA e One UXGA input and two outputs on 15 pin HD computer graphics video connectors e One digital audio input and two outputs S PDIF on RCA connectors as well as one analog audio input and two outputs on 3 5mm mini jacks e A transmission range of up to 300ft up to 100 meters over STP cabling e Changeable polarity for decoding H and V Sync for video UXGA The TP 210A is housed in a 19 1U rack mountable enclosure with rack ears included and is fed from a 100 240V AC universal switching power supply About the Power Connect Feature The Power Connect feature applies as long as the cable can carry power This feature is available when using STP cable and the distance does not exceed 50m on standard CAT 5 cable For longer distances heavy gauge cable should be used For units which are connected via RJ 45 connectors make sure that the shield of the STP cable is connected to the metal casing of the connectors on both ends of the cable For units which are connected via terminal block connectors the shield of the STP cable must be connected to a ground terminal on the units at both ends use the ground terminal of the power supply connection if necessary For a CAT 5 cable exceeding a distance of 50m separate power supplies should be connected to the transmitter and to the receiver simultaneously 1 Selectable analog or digital S PDIF audio signal 2 CAT 5 cable is
15. upplied with the product iii Repairorattempted repair by anyone not authorized by Kramer iv Any shipment of the product claims must be presented to the carrier v Removalorinstallation ofthe product vi Anyothercause which does not relate to a product defect vii Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WILLPAY FOR AND WHAT WE WILLNOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following 1 Removalorinstallations charges 2 Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased 3 Shipping charges HOW YOU CAN GET WARRANTY SERVICE 1 obtain service on you product you must take or ship it prepaid to any authorized Kramer service center 2 Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem s 3 For the name of the nearest Kramer authorized service center consult your authorized dealer LIMITATION OFIMPLIED WARRANTIES All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length
16. years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function Thank you for purchasing the Kramer 210 UXGA Audio RS 232 Line Transmitter DA which is ideal for e Presentation and multimedia applications e Long range graphics distribution for schools hospitals security and stores The package includes the following items e 210 UXGA Audio RS 232 Line Transmitter DA e Power cord e This user manual 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual e Use Kramer high performance high resolution cables 1 GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Matrix Switchers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters GROUP 11 Sierra Products 2 We recommend that you use only the power cord supplied with this device 3 Download up to date Kramer user manuals from our Web site at http www kramerelectronics com 4 The complete list of Kramer cables is on our Web site at http www kramerelectronics com
Download Pdf Manuals
Related Search