User Manual - Automated Environmental Systems
Contents
1. AND MOTOR 1 Plugged basket in skimmer or hair in lint strainer Worn motor bearings Valve in suction line partly closed Suction line partly plugged Vacuum hose plugged or too small Pump not supported properly AIR BUBBLES AT INLET FITTINGS 1 Leakage of air into suction line at connections or valve stem 2 Cover gasket of hair and lint strainer needs cleaning 3 Low water level in pool NOTE If the recommendations in the trouble shooting portion of this manual do not solve your particular problem s please contact your local dealer for service2. DISCHARGE PORT TO SUCTION PORT FROM POOL OR VACUUM FILTER tat WU z z CLI a ir FILTER OR POOL PUMP MAY BE BOLTED TO LEVER FOUNDATION OR MOUNTING BRACKET PARTS OF PUMP STAINING SCREWS OF PUMP BODY Description Part No Lid lock ring CP 01 02 Lid CP 01 03 O ring CP 01W 01 Stop back valve CP 01 12 Basket Hair with lint pot CP 01 04 CP 01 05 O ring bulkhead CP 01W 04 O OlN OD Oa AI OJN Bulkhead fitting MPV 02 005 Adaptor bulkhead MPV 02 007 io Nut bulkhead VIPI S a a a a a MPV 02 006 Drain plug with o ring CP 01 013 CP 01W 05 SB Series Centrifugal Pump Installation amp Operating Instructions Gasket CP 01W 06 Nut CP 02W 03 2 Screw CP 01W 08 1HP 1 5HP 2HP 3HP Base Pump body CP 01 06 2 CP 01 06 1 CP 01 07 O ring CP 01W 10 Diffuser CP 01 08 Screw with o ring CP 01 10 CP 01W 05 Impeller CP 01 09 Shaft seal CP 01W 13 O ring CP 01W 14 Flange CP 01 11 Screw CP 01W 16 Screw CP 01W 17 1HP 1 5HP on 2HP3Hp O9 CP 01W 18 1 CP 01W 18 2 Over load switch CP 01W 19 Irdome CP 01 14 1HP 1 5HP 2HP 3HP COYS CP 01 13 2 CP 01 13 1 Motor CP 01W 31 Opening key CP 01 00
3. INSTALLATION Only qualified licensed personnel should install pump and wiring IMPORTANT ELECTRICAL Electrical Contractors Please Note All 220 volt 50 Hz pumps must be wired to the main power supply through an approved and correctly rated contactor Pump Mount Must Be solid Level Rigid Vibration Free Allow pump suction inlet height to be as close to water level as possible Allow use of short direct suction pipe To reduce friction losses Allow for gate valves in suction and discharge piping Have adequate floor drainage to prevent flooding Be protected from excess moisture All adequate access for servicing pump and piping NOTICE Pump suction and discharge connections have moulded in thread stops DO NOT try to screw pipe in beyond these stops EMPU05080302 OPERATION A NEVER run pump dry Running pump dry may damage seals causing leakage and flooding Fill pump with water before starting motor A Before removing lid STOP PUMP before proceeding CLOSE GATE VALVES in suction and discharge pipes RELEASE ALL PRESSURE from pump and piping system NEVER tighten or loosen screws while pump is operation Do not block pump suction To do so with body may cause severe or fatal injury Children using pool must ALWAYS have close adult Supervision CAUTION Hazardous suction Can trap hair or body part causing severe injury or f death say In a flooded suction system wate
4. PARTS Refer all service to your local agent or dealer as his knowledge of your equipment makes him the vest qualified source of information Order all repair parts through your dealer Give the following information when ordering repair parts 1 Unit nameplate data or serial number on label 2 Description of part TROUBLE SHOOTING MOTOR DOES NOT START 1 Disconnect switch or circuit breaker in off position Fuses blown or thermal overload open Locked motor shaft Motor windings burned out Defective starting switch inside singl phase motor 6 Disconnected or defective wiring 7 Low voltage PUMP DOES NOT REACH FULL SPEED 1 Low voltage 2 Pump connected for wrong voltage MOTOR OVERHEATS protector trips 1 Low voltage 2 Motor windings connected for wrong voltage on dual voltage model 3 Inadequate ventilation PUMP DELIVERS NO WATER 1 Pump is not primed 2 Closed valve in suction or discharge line 3 Leakage or air into suction system 4 Impeller clogged LEAKAGE OF WATER AT SHAFT 1 Shaft seal requires replacement LOW PUMP CAPACITY 1 Valve in suction or discharge line partly closed 2 Suction or discharge line partly plugged 3 Suction or discharge line too small 4 Plugged basket in skimmer or hair and lint strainer Dirty filter Impeller clogged HIGH PUMP PRESSURE 1 Discharge valve or inlet fittings closed too much 2 Return lines too small 3 Dirty filters NOISY PUMP
5. r source higher than pump Do not block pump will prime itself when suction and discharge valves are suction opened If pump is not in a flooded suction system unscrew and remove trap cover fill trap and pump with water Clean and inspect Ring re install on trap cover Replace trap cover on trap turn clockwise to tighten cover NOTICE Tighten trap cover by hand only Pump should prime now Priming time will depend on vertical length of suction lift and horizontal length of suction piping Priming Pump Release all air from filter and piping system see filter owner manual Routine Maintenance The only routine maintenance needed is inspection cleaning of trap basket Debris or trash that collects in basket will choke off water flow through the pump Follow instructions below to clean trap 1 Stop pump close gate valve in suction and discharge and release all pressure from system before proceeding 2 Unscrew trap lid turn counterclockwise 3 Remove strainer basket and clean Be sure all holes in basket are clear flush basket with water and replace in trap with large opening at pipe connection port between ribs provided If basket is replaced backwards cover will not fit on trap body 4 Clean and inspect lid Ring reinstall on trap cover 5 Clean Ring groove on trap body and Replace lid To help keep lid from sticking tighten hand tight only 6 Prime pump see priming instructions above SERVICE amp REPAIR
Download Pdf Manuals
Related Search