eBuddy 9.4 User`s Manual
Contents
1. Caution When you re install operating system by Recovery CD for Windows we STRONGLY recommend connecting the AC adapter do NOT use battery alone to avoid warning message 41 Chapter 4 System Software Recovering Windows and Original Software If your Windows operating system is lost or damaged use the Recovery CD Windows Enter BIOS setup Set first boot device to CD ROM See Chapter 6 BIOS Settings Put the Windows Recovery CD into the CD ROM drive and reboot the computer Hard disk partitioned NO Follow the instructions in the sections below Partitioning the hard drive Recovering Windows Creating a Suspend to Disk Partition Windows 98SE only Recovering original software YES Follow steps under Recovering Windows 42 System Software System Recovery Partitioning the Hard Drive Hard drive is not partitioned When the Microsoft Windows startup menu appears select 2 Go to MS DOS PROMPT Press Enter to repartition your hard disk At the A prompt type fdisk and press Enter Note If your computer is set to boot from the CD ROM drive A refers to your CD ROM If you see the message Do you wish to enable large disk support Y N Select Y On the first screen select Create DOS partition or logical DOS drive On the next screen select Create Primary DOS partition This will create the largest possible partition as the C drive Afte2. Introduction Loading Windows Loading Windows The following section is for installing the Windows operating system only If you are installing a different operating system please check with your vendor for installation details _ GT TT SC Lk mam WE YYY 12345 Your computer will if am I H DCD H begin loading Windows once you turn on the power Wait a few seconds for Windows B rsegof Eeer setup to load The Windows setup will prompt you for the product key number shown to the right XXX 12345 Product key number Note The product key is on a sticker attached to the bottom of the Notebook 1 Type your name and if applicable the name of your company 2 Read the End User s License Agreement Click Next to accept it 3 Enter the product key number You can find this on the Certificate of Authenticity on a sticker attached to the computer Click Finish 4 The Start Wizard will prompt you to set the date and your local time After the Start Wizard updates your system settings the Welcome to Windows screen will appear You may disable this feature by clearing the check box labeled show this screen each time Windows starts Some software comes preloaded with Windows New users can familiarize themselves with this software by selecting Programs from the start menu then clicking on programs to run them Caution When you are installing the Windows A operating system and enter the pro
3. Getting Started The CD ROM DVD ROM Combo Drive or DVD RW The CD ROM DVD ROM Combo Drive or DVD RW Your computer comes with a pre installed CD ROM DVD ROM Combo drive or DVD RW The CD ROM drive is a read only drive It cannot be used to write data to a recordable CD The CD ROM drive can read data from CDs including audio or video CDs The CD RW can perform these same functions as well as record information to writeable CD s The DVD drive can read both DVDs and CDs Your notebook identifies the drive with the letter following the hard drive letter If your hard drive is D then the CD ROM drive will be E Inserting a Disk 1 Press the button on the front of the drive to open the disk tray and pull the tray open 2 Place the disk on the tray label side up 3 Place the disk on the central spindle and press gently until the disk clicks into place 4 Slide back the tray until it clicks shut Removing a Disk a wi QI 1 Make sure the computer is not w accessing the CD ROM drive 2 Press the eject button and pull the tray all the way out 3 Pick up the CD by the edges and bi remove the CD ROM from the tray P sS Push the tray into the computer 00 AE until it closes fully ROM CD RW DVD the indicator light for the CD ROM will flash on Do not attempt to remove a disk while this light is active The lock is located to the left of the eject button In locked mode the drive will stop if the ejec
4. When used with fax software it can be used as a fax When using this function first plug the phone cord into the jack Attention When using the data communications function please do not plug the phone cord into the ISDN or PBX jack to avoid an electrical surge that will cause the MDC module to burn 31 Chapter 2 Getting Started Information about the Wireless LAN button Wireless LAN button Even when a Wireless LAN module has not been built in to your computer the Wireless LAN indicator remains in active when you press the Wireless LAN button near the power button of your computer If Wireless LAN module has been built in your notebook will search for the device and will display an icon on the Windows task bar Built in Wireless Local Area Network The built in Wireless Local Area Network WLAN interface card can provide a quick access without using cables for the connection to the network equipments The interface card adopts the IEEE 802 11 protocol and uses the 2 4 GHz 5 GHz ISM electric wave frequency band as the transmission interface to set up the communications between the host computer and other computers The way of processing communications through the WLAN interface card is the same as that through Ethernet interface card The Configuration Tool is a Window application program If users have a computer equipped with the WLAN interface card then users can use it to set up the interface card
5. Device 3 Boot Device CD DVD HDD Network Realtek Bo Specifies the boot sequence from the available devices A device enclosed in parenthesis has been disabled in the corresponding type menu lt Select Screen fy Select Item Enter Go To Sub Screen F1 General Help F10 Save and Exit ESC Exit V02 57 Copyright 1985 2004 American Megatrends Inc 58 Using the BIOS Setup Utility USecurity Menu Security Menu BIOS SETUP UTILITY Main Advanced Boot Security Exit Security Settings Install or Change the password Supervisor Password Not Installed User Password Not Installed Change Supervisor Password Change User Password lt Select Screen 1 Select Item Enter Change Fl General Help F10 Save and Exit ESC Exit V02 57 Copyright 1985 2004 American Megatrends Inc 59 Chapter 6 Using the BIOS Setup Utility Change Supervisor Password Enter new password Supervisor Password Indicates whether a supervisor password has been set If the password has been installed Installed displays If not Not Installed displays Change Supervisor Password Select Change Supervisor Password from the Security Setup menu and press lt Enter gt Enter New Password appears Type the password and press lt Enter gt The screen does not display the characters
6. Menu u uuu2222000 APPENDIX A FREQUENTLY ASKED QUESTIONS Frequently Asked Questions 35 36 36 37 38 39 40 41 45 46 48 50 50 51 53 54 55 56 57 58 59 60 60 62 63 APPENDIX B STATEMENTS 67 IT EC 68 European Notice rrnnsnvnnnnnnnvennnnnnnvnnnnnnnvennnnnnvennnnnnvennnnnnnvenennnnvenennnnr 71 HL CAUTION annie ar 71 Canadian Department of Communications mrnrnnverrnnnnvvvnnnnnvnvennnn 72 Battery Disposal rrnannvnnnnnnnvnnnnnnnvnnnnnnnvnnnnnnnvnnnnnnnnvennnnnnvennnnnnvennnnnne 73 CAUTION FOR ADAPTER mnnnnnnnnnnnnnnnvnnnnnnnnnnnnnnnnnnnnnnnnnnnvnnnnnnnnnnnnnnnnr 73 BATTERY CAUTION 2 en 73 CLASS 1 LASER PRODUCT rrnnnnvnnnnvnnnnvnnnnnnnnnnnnnnnnvnnnnnnnnnnnnnnnnvnnnnnr 73 Macrovision DVD License Agreement nnssrnnnnnnnnvnnnnnnnvnnnnnnnvnnnnnnnne 74 Chapter 1 Introduction m Zz Q 7 T Chapter 1 Introduction Getting Started Congratulations on your purchase of the Notebook computer Your new notebook features the most innovative advances in portable computing technology lt combines state of the art ergonomics with sophisticated architecture to provide you with a personal computer that is compact powerful and easy to use Designed for a wide range of general business and personal productivity applications the notebook is an ideal choice for use in the office at home and on the road For maximum expandability without compromising portab
7. a SPDIF speakers to this jack to listen audio sound 3 Audio out Jack Connect a stereo headset or external speakers to this jack to listen to multimedia 4 Microphone in Jack Connect a microphone to this jack to record audio Chapter 4 System Software m rd O d I Chapter 4 System Software System Software Software List Operating System Your hard drive already contains all the software you need to operate the computer Audio and Video Drivers These utility programs and drivers are included for the PC Card drive the sound system and the graphics sub system DVD Player Application The DVD player application will let you watch DVD movies on your notebook for DVD ROM DVD RW module only 40 System Software System Recovery System Recovery Before you start Your system includes two Recovery CD ROMs Follow the steps in the appropriate section below to reinstall the operating system the system software or add a new hard disk The factory has pre partitioned your system s hard disk so you may directly install the system software however if you change a new hard disk you must first partition it If you reinstall your operating system all of the data originally on the hard disk will be overwritten Before reinstalling the operating system carefully backup any important data Your system is shipped with two different Recovery CD ROMs Before reinstalling note the CD ROM labels
8. and show the current configuration and status Note Contact your distributor for the information of upgrading the wireless local area network 32 Getting Started Information about the Wireless LAN button DGT Warning Article 14 Without permission any company firm or user shall not alter the frequency increase the power or change the characteristics and functions of the original design of the certified lower power frequency electric machinery Article 17 The application of low power frequency electric machineries shall not affect the navigation safety nor interfere a legal communication if an interference is found the service will be suspended until improvement is made and the interference no longer exists The foregoing legal communication refers to the wireless telecommunication operated according to the telecommunications laws and regulations The low power frequency electric machinery should be able to tolerate the interference of th lectric wave radiation electric machineries and equipments for legal communications or industrial and scientific applications 33 Chapter 2 Getting Started 34 Chapter 3 Making Connections m rd O d I Chapter 3 Making Connections Making Connections Your computer is equipped with a full array of ports and connectors including standard input output I O ports for quickly and easily adding peripheral devices such as printer
9. as a special file When the computer returns from suspend mode the desktop appears with the same files and programs open as when the computer was suspended Suspend to Disk is very useful when you don t want to take the time to shut down all open programs one by one to shut off the computer only to have to open the same programs and files the next time you use the computer This mode is also called hibernation mode Suspend to disk Partition Suspend to disk File Suspend to Disk file will be saved by Windows to the hard disk The size of the file will correspond to the amount of system memory Please make sure there is enough space on the hard disk Support wake up on LAN in standby amp Hibernate mode System is shutdown Initiating Suspend Mode There are four ways to initiate suspend mode The settings can be adjusted in the Power Management dialog box e The computer will automatically enter suspend mode when not used for a set period of time e Selecting the Stand by button in the Shut Down Windows dialog box e Closing the screen cover assuming no external monitor has been connected e Pressing the power button if enabled in power settings e Pressing the suspend function key lt Fn gt lt F3 gt 49 Chapter 5 Power Management Power Saving Tips e Avoid operating the fax modem or audio and video applications when using battery power Operating a fax modem video or audio equipment or turning
10. external microphone can I use with my notebook computer You will need to use a self amplifying microphone 64 Appendix A Frequently Asked Questions There is feedback noise coming from my speakers What can I do Double click on the Speaker icon on the task bar Then under Microphone Balance check the Mute box Because of a software problem I was unable to shut down power normally I pressed the power button to force a power off but it didn t work How can I force a power off Make sure you press the power button for at least 4 seconds Normally this will force a power off Why can t I charge the battery of my portable computer after it was out of use for some time After portable computers have not been used for a long time more than one month the batteries will go into the low voltage protection mode due to data back ups and natural electrical discharge At that point restoring normal voltage will require slow charging over a period of several hours Calibration can be performed after the battery has returned to a normal condition 65 Appendix A Frequently Asked Questions 66 m p O d I Appendix B Statements Appendix B Statements Statements Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protec
11. should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection In some cases the company s inside writing associated with a single line individual service may be extended by means of a 72 Appendix B Statements certified connector assembly telephone extension cord The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas CAUTION Users should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician as appropriate The Load Number LN assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device To prevent overloading the ter
12. users can find a simple step by step orientation in the Quick Start section of this chapter About Windows The Windows Manual provides an overview of the Windows operating System Windows Online Help found on the Start menu offers extensive Windows assistance Welcome to Windows offers an online orientation for new Windows users Find it in Start Programs Accessories System Tools Chapter 1 Introduction Quick Start Turning on the Computer for the First Time 1 Connect the AC adapter power cord to the AC adapter Connect the AC adapter to the DC power port on the left side of your computer Connect the AC adapter power cord to an AC outlet 3 Open the LCD panel to s 1 a comfortable viewing Z Iq angle Press the power button to turn on the power Note The battery is not fully charged Allow your battery to fully charge before using it i e before disconnecting AC power Calibrating the battery befor use is also highly recommended Refer to Chapter 5 Power Management for further information Use the touchpad to move the cursor on the screen Move your finger across the pad to control the cursor and press the right and left buttons beneath with your thumb These buttons have the same functions as the right and left buttons of a standard mouse You can also click or double click by tapping on the touchpad The middle button can be used to scroll up and down in documents and Web pages
13. 9 Power Indicators rnnnnnnvnnnnnnnvnnnnnnnnvnnnnnnnvnnnnnnnvnnnnnnnvnnnnnnnnvnnnnnnnnenennnne 20 Function Keys nnsvnnnnnnnvnnnnnnnvnnnnnnnvnnnnnnnvnnnnnnnvnnnnnnnnvnnnnnnnvnnnnnnnnenennnne 20 Numeric Keypad mmmnnsvvnnnnnnvennnnnnvnnnnnnnvnnnnnnnnvnnnnnnnvnnnnnnnvenennnnvenennnnn 21 Jochpass ee EE ees 21 The CD ROM DVD ROM Combo Drive or DVD RW seess 24 Connecting the Printer rrnsavnnnnvnnnnvvnnnnvnnnnnvnnnnnnnnnvnnnnnnvnnnnnnnnnvnnnnnr 26 The PCMCIA Card SlOt srrnnnvnnnnnvnnnnnnnnnvnnnnnvnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnr 26 ET Oe Te E 27 The Graphics System rrnsevnnnnvrnnnnvnnnnnnnnnvnnnnnvnnnnnnnnnnvnnnnnnnnnnnnnnnnnnnnnr 28 Communication ComponentS rrnssvvnnnnvnnnnnnnnnnnnnnnvnnnnnnnnnnnnnnnnnnnnnnr Information about the Wireless LAN button s errnnnnvvnnnnnnvnnnnnnnnr CHAPTER 3 MAKING CONNECTIONS Making Connections Left Side Connectors Right Side Connectors Front Side Connectors CHAPTER 4 SYSTEM SOFTWARE System Software eessen System Recovery seen CHAPTER 5 POWER MANAGEMENT Power Management Power Saving Modes Power Saving Tips When to Replace the Battery Heat Considerations CHAPTER 6 USING THE BIOS SETUP UTILITY Using the BIOS Setup Utility Navigating and Entering Information in BIOS rrsvrnnnnvnnnnvnnnnvenn The Main Menu u222202002 Advanced
14. A Warning After KBC firmware update is complete 55 Chapter 6 Using the BIOS Setup Utility The Main Menu BIOS SETUP UTILITY Main Advanced Boot Security Exit System Overview Use ENTER TAB Or SHIFT TAB to select a field AMIBIOS Version R0 00 Use or to Configure system Time Processor Type Intel Pentium M processor 1 60Ghz lt gt Select Screen Speed 1600MHz 1 Select Item Change Field System Memory Tab Select Field Size 480MB F1 General Help F10 Save and Exit System ime 19 14 50 ESC Exit System Date Thu 11 13 2003 V02 57 Copyright 1985 2004 American Megatrends Inc 56 Using the BIOS Setup Utility UAdvanced Menu Advanced Menu BIOS SETUP UTILITY Main Advanced Boot Security Exit Advanced Setting Disable Enable Auto DIM function Enabled Legacy USB Support Enabled Serial Port Address 3F8 IRQ4 Com Port Modem RI Resume Enabled Touchpad Support Enabled lt gt Select Screen Share Memory Enabled 32MB 3 Select Item Fan Auto Learning Enabled Change option Battery Auto Learning Enabled F1 General Help F10 Save and Exit ESC Exit V02 57 Copyright 1985 2004 American Megatrends Inc 57 Chapter 6 Using the BIOS Setup Utility Boot Menu BIOS SETUP UTILITY Main Advanced Boot Security Exit 1 Boot Device 2 Boot
15. IOS Setup Utility 3 Inthe BIOS Setup Utility select Advanced Setup choose Start Battery Learning then press lt Enter gt Please make sure that AC adapter amp Battery are present Would you like to do battery learning OK Cancel 4 Select OK at the above Battery Auto Calibration dialog to begin the battery calibration Please press Y to continue Battery Calibration will take from 10 to 16 hours depending on how much power the battery may already contain Note For optimum performance we recommend calibrating the battery again every three months Each time you charge and discharge a battery it loses a tiny part of its storage capacity so that over time it will store less than its potential charge Similarly if you do not use the battery for a few days it will slowly self discharge and when it is recharged it will hold less than 100 of the potential charge 46 Power Management Power Management Monitoring Battery Power There are two ways to 2x monitor how much power the Power Schemes Alarms Power Meter Advanced Hibemate battery has left SE GE 1 Click Start Settings ee VE Control Panel Power 8 Options then click du Power Meter GE 2 Moving the cursor to the battery icon on the taskbar is the simplest way to check on battery ica individual bat icon far more information power status Cancel If you do not see the battery i
16. at may cause undesired operation 68 Appendix B Statements About The Modem This equipment complies with Part 68 of FCC rules On the bottom of this equipment is a label that contains among other information the FCC registration number and ringer equivalence number REN for this equipment If requested this information must be provided to the telephone company The modem jack of this equipment complies with Sub part F of Part 68 of FCC rules The REN is used to determine the quantity of devices that may be connected to the telephone line Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call In most but not all areas the sum of the RENs should not exceed five 5 0 To be certain of the number of devices that may be connected to the line as determined by the total RENs contact the telephone company to determine the maximum REN for the calling areas If the terminal equipment causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of service may be required However if advance notice isn t practical the telephone company will notify the customer as soon as possible Also you will be advised of your right to file a compliant with the FCC if you believe it necessary The telephone company may mark changes in its facilities equipment operations or procedures that could affect the operation of the equipment I
17. ce appears If your computer is already on either power off or select restart option under windows environment Restart it and then press the Del key to enter the setup utility configure your computer s basic settings we STRONGLY recommend connecting the AC adapter do A Warning When you use the BIOS setup utility to NOT use battery alone to avoid warning message 54 Using the BIOS Setup Utility Navigating and Entering Information in BIOS Navigating and Entering Information in BIOS Use the following keys to move between fields and to enter information en men Press Del to start the BIOS utility after turning on the computer Press Esc to exit any section If you wish to exit the BIOS utility without saving changes go to the main menu then press Esc Push the up and down arrow keys to move Up down keys MY among selections then press Enter to make a selection Use the keys to modify a field Use to increase a value such as a date or number and to decrease it For other types of choices such as enabled or disabled use either key to move between choices Ta Press tab to make a selection Fl np Press F10 to save changes then exit the system will automatically shut down Please unplug all power sources including AC or battery and replug or use a paper clip to depress the forced shutdown hole on the bottom of the computer This will enable new settings to be entered
18. con enable it in Start Settings Control Panel Power Options Choose the Advanced tab and click Always show icon on the taskbar Low Battery Alarms How your computer responds to a low battery condition is set under Start Settings Control Panel Power Options Alarms Two different power alarms can be enabled or disabled the Low Battery Alarm and the Critical Battery Alarm Use the slide bar to set the power level at which the alarms are activated Click on the Alarm Action button to choose whether the alarm sounds displays a message or both indicator will flash red and the alarm will beep or display a warning on your screen Take immediate action such as saving files or connecting to the AC adapter or data may be lost Warning When battery power is low the battery When the computer alerts you that the battery is low immediately do one of the following e Connect the AC power adapter e Save your work and suspend to disk lt Fn gt lt F3 gt e Save your work then select Shut Down from the Start menu 47 Chapter 5 Power Management e Turn off or suspend the computer and replace the discharged battery with a charged battery See Battery Charging below Do not restart the computer until you have connected to an AC adapter or replaced the discharged battery with a charged battery Battery Charging When you use the AC adapter to connect your Notebook to a power outlet the internal batte
19. duct key number we STRONGLY recommend connecting the AC adapter do NOT use battery alone to avoid warning message Chapter 1 Introduction Adjusting the Volume You can adjust the volume with the volume control knob located below the touchpad Control Knob Alternatively you can adjust the volume with the Windows volume control applet located on the taskbar Volume Adjusting the Brightness Use the following hot key combinations to adjust the LCD panel brightness e Fn F6 decreases the brightness e Fn F7 increases the brightness 10 Introduction Turning off Your Computer Turning off Your Computer Turning off the computer properly is important to maintaining your computer 1 On the Start menu click Turn 2 Click the Turn Off button Off Computer 7 Run Turn off computer P Log Off t 9 Turn Off Computer Windows XP star 8 G If you are going to be away from the computer for a short period there are ways of conserving power without shutting down the system See Chapter 5 Power Saving Modes for details Warning Shutting off the computer improperly may result in data loss Making a Startup Disk If you have trouble starting Windows the startup disk can be used to start your computer and fix many problems Refer to the Windows user manual for instructions Tips for New Owners Take responsibility for backup Back up files often Users who need to manage la
20. e normal typing position The touchpad is easily accessible by moving either your left or right thumb off the space bar and on to the touchpad 2 Gently move your thumb across the pressure sensitive touchpad in the direction you want the cursor to move The pad detects the change in pressure and moves the cursor in the corresponding direction 3 The touchpad offers another method of making selections in a software program It is called double tapping This function corresponds to double clicking with a mouse Once the cursor has been moved to the object you want to select lightly double tap the pressure sensitive touchpad This double tapping on the touchpad will select the desired item and prompt the software to perform the related operation 4 The buttons located directly below the touchpad are the same in function as those on a two buttoned mouse Clicking these buttons 21 Chapter 2 Getting Started makes selections drags objects or performs a variety of other functions depending on the software To select an object first move the pointer over the object you want to select and then press the left button one time The functions of these buttons are software specific 5 Double clicking is a common technique for selecting objects or launching programs from icons Once you have moved the pointer over the object you wish to select rapidly press the left button two times This action is commonly referred to as double clickin
21. eBuddy 9 4 User s Manual egen XW EarthWalk a step ahead 10262 Battleview Parkway Manassas VA 20109 7033931940 wwwearthwalkcom Table Of Contents CHAPTER 1 GETTING STARTED 1 EE le E WE 2 Inventory TEE 3 Safety and Maintenance rnnnvnnnnvnnnnnvnnnnnvnnnnvnnnnnnnnnnnnnnnvnnnnnnnnnnnnnnnnenn 4 Checklists ainia onanan aona anaa aoaaa pa yaoa emnet emesaesesteen 5 Features PAEA AEE EE EE 6 Where to Look For Information rrnnnnvennnnnnnvnnnnnnnvnnnnnnnvnnennnnnvenennn 7 QUICK St rt aent das Eed 8 Loading Windows s runnnnnvnnnnnnnvennnnnnvnnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnennnnnneennnnnnenr 9 Adjusting the Volume rnseennnnnnvnnnnnnnnvnnnnnnnvnnnnnnnvnnnnnnnvnnnnnnnnnnnnnnnnnnenn 10 Adjusting the Brightness nrssvvrnnnnnvvnnnnnnnvnnnnnnnvnnnnnnnvnnnnnnnnnnnnnnnnnnenn 10 Turning off Your Computer rrrsavrnnnnvnnnnvnnnnnvnnnnnnnnnnvnnnnvnnnnnnnnnnnnnnnnr 11 Making a Startup Disk rrrnvrnnnnvnnnnnvnnnvvennnnvnnnnnnnnnnnnnnnvnnnnnnnnnnnnnnnnnnn 11 Tips for New Owners ssrnnnnvrnnnvnnnnnvnnnnnnnnnvnnnnnnvnnnnnnnnnvnnnnnvnnnnnnnnnnnnnnnr 11 CHAPTER 2 GETTING STARTED 13 Hardware and Software rrnnnvnnnnnvnnnnvnnnnvnnnnnvnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnenn 14 Front VIEW Ladies 15 Lett VIEW sne EE 16 Right EE 17 Bottom VieW unrsnsvnnnnnnnvnnnnnnnvennnnnnnvennnnnnvnnnnnnnvennnnnnvennnnnnnvennnnnnvennnnne 18 LED Status IndicatOrS rrrsvnnnnnvnnnnvnnnnvnnnnnvnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnenn 1
22. ebook via the USB port use the optional USB to printer adapter cable Note Before use you must install the driver for the adapter cable The PCMCIA Card Slot The PC card slot can be used as an interface between your computer and a variety of communications devices such as network adapters SCSI adapters fax modems or provide additional data storage capacity Your computer s PC card slot supports PCMCIA Type II and 32 bit CardBus Installing a Card 1 The top side of a PCMCIA card is usually identified with a label Insert the card into dn the slot with the label side up and the edge with pinhole Slide the card contacts going in first into the slot 2 Insert the card into the slot Sash the E You will feel some resistance eject the card as the card slides into the back of the slot 3 PCMCIA cards require drivers or a program that allows the operating system to use a specific device Many drivers are included with Windows but if not you will be prompted to install the driver included with your card wa o gt ME por Removing a Card 1 Ifa card is in use you must shut down the card before removing it Or you can click the PCMCIA icon on the right side of the taskbar then click Stop 2 Select the PCMCIA card in the next window and click OK 3 Press the eject button on the card slot to release the button 4 Press again to release the card 25 Chapter 2 Getting Started Memory Addin
23. en the card is fully inserted 3 Press the card downwards so that it is flat inside the compartment 4 You may hear an audible click as the latches of the connector lock the card in place Replace the RAM compartment cover and secure it with the two screws Your notebook computer will automatically detect the change in RAM capacity when it restarts 27 Chapter 2 Getting Started The Graphics System Your computer has a high performance graphics system which can easily handle the demands of today s multimedia computing Screen Controls Brightness Function keys can increase or decrease the brightness of the monitor e lt Fn gt lt F6 gt decreases the LCD panel brightness e lt Fn gt lt F7 gt increases the LCD panel brightness Resolution 1 Click My Computer Control Panel Display Settings Click the Settings tab The dialog box indicates the monitor resolution 2 Use the slide bar to adjust the resolution Normally you should use the resolution the LCD or monitor was designed for Note Using a lower resolution than the screen was designed for will reduce the area of the display Using the computer in DOS mode may produce the same effect because it uses a 640 by 480 resolution by default You can stretch these low resolution displays to full screen size by selecting either the Expanded Display or Display Expansion Mode features in the BIOS utility However the stretching may cause distortion es
24. entered Retype the password as prompted and press lt Enter gt If the password confirmation is incorrect an error message appears Change User Password Enter new password User Password Indicates whether a user password has been set If the password has been installed Installed displays If not Not Installed displays Change User Password Select Change User Password from the Security Setup menu and press lt Enter gt 60 Using the BIOS Setup Utility U Exit Menu Enter New Password appears Type the password and press lt Enter gt The screen does not display the characters entered Retype the password as prompted and press lt Enter gt If the password confirmation is incorrect an error message appears 61 Chapter 6 Using the BIOS Setup Utility Exit Menu BIOS SETUP UTILITY Main Advanced Boot Security Exit Exit Options Exit system setup After saving the changes Save Changes and Exit Discard changes and Exit F10 key can be used Discard Changes for this operation Load Optimal Defaults lt gt Select Screen ty Select Item Enter Go To Sub Screen Fl General Help F10 Save and Exit ESC Exit V02 53 Copyright 1985 2002 American Megatrends Inc 62 Appendix A Frequently Asked Questions m rd Q d x Appendix A Frequently Asked Questions Frequently Asked Questions Q My screen seems to time out too qu
25. ew p Pr TET 1 2 3 4 5 6 8 10 Shoulder strap hole Kensington lock hole Ventilation slots DC adapter port VGA port external video display LAN Ru 45 jack RJ 11 jack USB port PCMCIA card slot 0 PCMCIA card eject button Bi D Jm pm Spa 16 Getting Started Bottom View Right View N S ON USB ports S Video port CD ROM DVD ROM Combo DVD RW drive CD ROM DVD ROM Combo DVD RW drive lock CD ROM DVD ROM Combo DVD RW drive eject button Com Port Shoulder strap hole 17 Chapter 2 Getting Started Bottom View Ventilation slots WLAN Module Battery release button Battery SO DIMM DDR RAM Module HDD Module GROD gt 18 Getting Started LED Status Indicators LED Status Indicators The status indicators in the upper left corner of the keyboard light up when a particular function of the computer is active Each indicator is marked with a symbol The computer is reading information CD ROM Drive Tom the CD ROM CD RW or the DVD ROM drive HDD The computer is reading from or writing to the built in hard disk Number Lock The keyboard is in Num Lock mode Caps Lock The keyboard is in Caps Lock mode D En DOG Scroll Lock The keyboard is in Scroll Lock mode Lei Wireless LAN The Wireless LAN is accessing 19 Chapter 2 Getting Started Power Indicators The power indicators show wh
26. f this happens the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service If trouble is experienced with this equipment please contact the manufacturer for repair and or warranty information If the trouble is causing harm to the telephone network the telephone company may request you remove the equipment from the network until the problem is resolved The equipment cannot be used on public coin service provided by the telephone company Connection to Party Line Service is subject to state tariffs Contact the state public utility commission public service commission or corporation commission for information 69 Appendix B Statements The Telephone Consumer Protection Act of 1991 marks it unlawful for any person to use a computer or other electronic device including fax machines to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission the date and time it is sent and an identification of the business or other entity or other individual sending the message and the telephone number of the sending machine or such business other entity or individual The telephone number provided may not be a 900 number or any other number for which charges exceed local or long distance transmission charges To program this information refer to the manual of t
27. g an object Dragging There are two ways to drag e Move the pointer to the desired location then press down the left button While still holding down the left button move the pointer to the desired location Release the button e Move the pointer to the desired location Tap the touchpad twice quickly as if you were double clicking however do not remove your finger after the second tap Move the cursor to the desired location Lift your finger to finish dragging Adjust the touchpad settings by selecting Settings Control Panel Mouse Buttons These settings allow you to change the orientation of the touchpad from right handed to left handed and fine tune the pointer movement and timing of clicks Touchpad Precautions The Touchpad is a pressure sensitive device If not properly cared for it can be easily damaged Please take note of the following precautions e Make sure the touchpad does not come into contact with dirt liquids or grease e Do not touch the touchpad if your fingers are dirty e Do not rest heavy objects on the touchpad or the touchpad buttons Scrolling Buttons If you are scrolling through a document you may find that using the scrolling button is more restful to your hand than holding down a mouse button The scrolling button is located between the touchpad buttons Push the top of the button to scroll up in a document or Web page press the bottom of the button to scroll down in a document or Web page 22
28. g memory allows the computer to operate faster handle more tasks simultaneously and work more smoothly with large files Users who increase memory demands by adding additional programs for example may notice a slowdown in operating speed and wish to increase memory The notebook includes a memory card slot for adding additional memory Note Use only 1 inch SODIMM modules Calculate memory size by adding the size of the memory module to the two memory slots For example 256 MB module 256 MB module 512 MB Total Replacing a Memory Card static electricity Leave the module inside its A Warning Memory modules can be easily damaged by static proof bag until it is ready for installation Removing a Memory Card 1 Turn off the computer and disconnect the AC adapter Turn the computer upside down and lay it on a flat surface 2 Carefully remove the two RAM compartment cover screws and remove the RAM compartment cover 3 Gently pull tabbed latched in the direction of the arrows 1 The card will pop up slightly 4 Pull upwards on the card and then slide the card out 2 26 1 n Getting Started Memory serting a Memory Card Hold the memory card by its edges with the edge connector side towards the slot Hold the card at a shallow angle about 25 degrees and insert the edge connector into the connector slot 3 The gold teeth of the edge connector should no longer be visible wh
29. he communication software R amp TTE CE MANUAL REGULATORY REQUIREMENT WLAN IEEE 802 11a b g 802 11a Restrictions e European standards dictate maximum radiated transmit power of 200mW EIRP and frequency range 5 15 5 35GHz and the equipment must be restricted to the 5 47 5 725 GHz frequency range and must be restricted to indoor use 802 11b g Restrictions e European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range 2 400 2 4835GHz e In France the equipment must be restricted to the 2 4465 2 4835GHz frequency range and must be restricted to indoor use Federal communications commission interference statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and 70 Appendix B Statements on the user is encouraged to try to correct the interference by on or more
30. ich power source the system is using They also show battery status and low battery power alerts The power indicators remain active and viewable even when the LCD panel is closed Icon Light Description Power is on and the AC adapter is in use Flashing Power is in suspend Blue mode Power is on and the Ea battery is in use Blue Blue Flashing Power is in suspend Blue mode Green Battery fully charged H Du Flashing Battery charging Green Red Battery charge fault indicator Function Keys Hold the Fn key while pressing the numbered function key Function key Description Fn F1 Toggles display on off Fn F2 Toggles between LCD CRT TV displays Fn F3 Suspend to RAM HDD Fn F6 Decreases LCD brightness Fn F7 Increases LCD brightness Fn F10 Speaker Mute On Off 20 Getting Started Touchpad Numeric Keypad The embedded numeric keypad consists of ten keys that make number intensive input more convenient Press lt NumLock gt to enable or disable the numeric keypad Touchpad The touchpad is a pressure sensitive pointing device that provides all the features of a two button mouse Its primary function is to move the cursor around the screen Touchpad Botton Touchpad Scrolling Button The instructions listed below describe how to use the touchpad 1 First place your fingers on the keyboard in th
31. ickly I have to constantly hit a key or move the mouse in order to bring it back How can I adjust the screen time out This is part of Windows Power Management Access Power Management by clicking on Start Settings Control Panel Power Management Adjust the display time out by selecting a time next to the Turn off monitor option You may also select different time out values for adapter and battery power states I ve heard that cleaning up and rearranging files on the hard drive will improve the startup speed of my programs How do I do this Hard disk maintenance can improve the startup speed of programs This maintenance includes deleting unnecessary files and defragmenting which rearranges data into more efficient groupings Windows includes utilities for performing these maintenance tasks In Windows 98 for example go to Start Programs Accessories System Tools Run Disk Cleanup to remove unnecessary files and Disk Defragmenter to defragment the hard drive For more information refer to Windows documentation The internal fax modem dial tone sound is too low How can I increase the volume There are two methods to adjust the volume of the internal fax modem dial tone Method 1 1 Use the volume control button on the front of the computer Method 2 gt To Start Setting Control panel Phone and Modem Options Modem Properties Modem Speaker Volume Adjust Move the slider to adjust the modem speaker volume What kind of
32. ility the notebook accommodates a number of modules including CD ROM DVD ROM Combo DVD RW Drive and 3 USB ports and one IEEE1394 port The high capacity hard disk drive provides you with plenty of storage space for multimedia files and applications This Manual contains all the information you need to set up and use your new notebook It describes all the features of the notebook in an easy to read yet thorough manner Introduction Inventory Inventory This computer system is designed for years of productive and pleasurable computing Use this section to keep details of your purchase This information will be required should you need to make repairs to your notebook during the warranty period Update this section when you add new options DATE OF PURCHASE PLACE OF PURCHASE DEALER S NAME DEALER S ADDRESS TELEPHONE E MAIL ADDRESS WWW CONTACT PERSON MODEL NUMBER SERIAL NUMBER BIOS VERSION The serial number is on the label with a bar code on the bottom side of the computer The BIOS revision number will appear briefly on the screen after turning on the computer before the graphic BIOS screen appears Press the Pause key to keep the number on the screen so you can record it Chapter 1 Introduction Safety and Maintenance You can use your computer under a wide range of environmental conditions However to ensure long use and continued high performance consider the fo
33. llowing factors when setting up your computer Follow all warnings and instructions noted in this documentation and in the Windows Help program The first time you use your computer we recommend that you carefully read the Making Connections section of this manual and initialize the battery to ensure optimum battery performance Unplug the computer from the power outlet before cleaning Use a damp cloth for cleaning Do not use aerosols solvents or strong detergents Do not use the computer near open water or other liquids Never spill liquid onto the computer Do not place the computer in an unstable location where it might slip or be knocked over Serious damage could result from a fall Slots and openings in the system cabinet are for ventilation purposes Do not block or cover these openings or the system could overheat Do not use or store the computer near a source of heat or dust On the base or rear panel of this notebook there is a label with information on the power requirements of this system These requirements must be followed If you are unsure of your local power supply consult your dealer or local Power Company Do not step on or place anything on the power cord If you use the computer with an extension cord ensure that the total ampere ratings of all the devices sharing the extension do not exceed the rating of the extension cord or the rating of the wall outlet Never push foreign objects into the compute
34. mination on a loop may consist of any combination of devise subject only to the requirement that the total of the Load Numbers of all the devices does not exceed 100 Battery Disposal THIS PRODUCT CONTAINS A LITHIUM ION OR NICKEL METAL HYDRIDE BATTERY IT MUST BE DISPOSED OF PROPERLY CONTACT LOCAL ENVIRONMENTAL AGENCIES FOR INFORMATION ON RECYCLING AND DISPOSAL PLANS IN YOUR AREA CAUTION FOR ADAPTER THIS NOTEBOOK COMPUTER IS FOR USE WITH MODEL NO LSE0202A2090 LSE9802A2060 adapter BATTERY CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER S INSTRUCTIONS 73 Appendix B Statements CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825 CAUTION THIS APPLIANCE CONTAINS A LASER SYSTEM AND IS CLASSIFIED AS A CLASS 1 LASER PRODUCT TO USE THIS MODEL PROPERLY READ THE INSTRUCTION MANUAL CAREFULLY AND KEEP THIS MANUAL FOR FUTURE REFERENCE IN CASE OF ANY TROUBLE WITH THIS MODEL PLEASE CONTACT YOUR NEAREST AUTHORIZED SERVICE STATION TO PREVENT DIRECT EXPOSURE TO THE LASER BEAM DO NOT TRY TO OPEN THIS ENCLOSURE Macrovision DVD License Agreement This product incorporates copyright protection technology that is protected by method claims of certain U S patents and other intellectual property rights owned by Macrovision Corporation and other rights owners U
35. ned for this system In this case you may use a PCMCIA modem 6 USB Universal Serial Bus Ports The Universal Serial Bus USB is the latest standard for attaching monitors input devices scanners and other devices to a PC USB devices can be chained together on a single cable Right Side Connectors 1 2 1 USB Universal Serial Bus Ports The Universal Serial Bus USB is the latest standard for attaching monitors input devices scanners and other devices to a PC USB devices can be chained together on a single cable 2 S Video Port S Video technology provides sharper video image on a video or television device than traditional TV out connections provided your video display device supports S Video output 3 Com Port The Com Port provides the connection for RS232 interface device such as mouse and modem Chapter 3 Making Connections jack only Most homes use analog lines Do not use digital lines such as the PBX and ISDN systems found in many offices Digital lines may damage your modem A Warning Plug your modem into an analog telephone Front Side Connectors 1 IEEE 1394 Port 4 pin The IEEE 1394 port is able to transfer large amounts of data at high speed Because of this ability the IEEE 1394 port is often used with multimedia devices such as video cameras However a variety of devices that support the IEEE 1394 standard can be connected to this port 2 SPDIF Jack Connect
36. neric Immunity Standard EN 60950 IEC60950 Product Safety 71 Appendix B Statements UL CAUTION To reduce the risk of fire use only No 26 AWG or larger telecommunication line cord IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment basic safety precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following Do not use this product near water for example near a bathtub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool Avoid using a telephone other than a cordless type during an electrical storm There may be a remote risk of electric shock from lightning Do not use the telephone to report a gas leak in the vicinity of the leak Use only the power cord and batteries indicated in this manual Do not dispose of batteries in a fire They may explode Check with local codes for possible special disposal instructions Canadian Department of Communications This class B digital apparatus meets all requirements of the Canadian Interference causing Equipment Regulations About the Modem The Industry Canada label identifies certified equipment This certification means that the equipment meets certain telecommunications network protective operational and safety requirements The department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users
37. of the following measures H Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference 2 this device must accept any interference received including interference that may cause undesired operation CAUTION Any changes or modifications not expressly approved by the grantee of this device could void the user s authority to operate the equipment FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body European Notice Products with the CE Marking comply with both the EMC Directive 89 336 EEC and the Low Voltage Directive 73 23 EEC issued by the Commission of the European Community Compliance with these directives implies conformity to the following European Norms EN 55022 CISPR 22 Radio Frequency Interference EN 55024 EN61000 4 2 EN61000 4 3 EN61000 4 4 EN61000 4 5 EN61000 4 6 EN61000 4 8 EN61000 4 11 EN61000 3 2 EN61000 3 3 Ge
38. on the Wireless LAN power button increases the computer s power requirements e Decreasing monitor brightness can also save power Decrease brightness by pushing lt Fn gt lt F6 gt Increase it by pushing lt Fn gt lt F7 gt When to Replace the Battery Over time the battery s capacity gradually decreases We recommend that you replace your battery when you notice that it begins to store significantly less charge Changing the Battery Change the main battery pack as follows 1 Turn off the computer 2 Close the screen cover and turn the computer over 3 Slide the side battery latch 1 away from the battery Continue to hold it until the battery is removed 4 Push in the latch on the battery 2 while lifting the battery out of the compartment Remove the battery 5 Make sure the replacement battery is properly orientated Slide back the side battery latch 1 then insert the battery into the battery compartment Check that the latch locks back into position Heat Considerations The computer s processor has been specially designed to consume little power and generates very little heat However working in a hot environment or working for long periods may raise the temperature Your computer takes the following steps to lower temperature 50 Power Management Heat Considerations The cooling fan will automatically turn on You may feel air coming from a vent at the left side when this ha
39. pecially to fonts High Resolution with an external monitor Higher resolution modes may be used as long as the monitor supports them Connecting to an External Monitor The notebook has a VGA monitor port to connect your computer to an external monitor Using the VGA monitor port 1 Locate the 15 pin VGA monitor port on the left side of your notebook and connect the video signal cable from the external monitor or the VGA adapter to the monitor port 2 Connect the power cable from the external monitor to a power outlet and turn on the monitor 3 On your notebook click the right touchpad button on the 28 Getting Started Dual Displays Windows desktop to open the desktop menu Click Properties to open the Display Properties window 4 Inthe Display Properties window click Advanced in the Settings tab Click the Display Modes tab 5 Under Driver mode you can select the appropriate options to change the display to an external monitor 6 Adjustments to screen resolution and color depth can also be made in this dialog box Dual Displays With Windows system you may use an external monitor simultaneously with your notebook s LCD You may also use the external monitor only and disable the LCD or only use the LCD To do this you may first need to enable the Intel dual display clone in Windows 1 Open the Control Mobile Intel R 915GM GMS 910GML Express Chipset Fam PAR Panel Devices Color Scheme
40. ppens If the temperature continues to rise processor activity will be reduced You may notice a slight loss of performance when this happens Warning If the operating temperature exceeds 100 c the system will shut down to prevent the heat from damaging the computer s infrastructure When the computer cools to a normal temperature you can restart the system The higher the temperature of the environment the longer the period the computer will need to cool down 51 Chapter 5 Power Management 52 Chapter 6 Using the BIOS Setup Utility m rd Q d x Chapter 6 Using the BIOS Setup Utility Using the BIOS Setup Utility Your notebook has a BIOS setup utility which allows you to configure important system settings including settings for various optional functions of the computer This chapter explains how to use the BIOS setup utility BIOS Setup Menu The setup uses a menu interface to allow the user to configure their system The features are Main Allows the user to specify system time and system date and the system overview Advanced Allows the user to set advanced settings Boot Allow the user to set the boot sequence Security Allows the user to set the password for system Exit Exit option Starting the BIOS Setup Utility You can only enter the BIOS setup utility as the computer is booting that is between the time you turn on the computer and before the Windows interfa
41. r completing disk partitioning press ESC to exit fdisk Press lt Alt gt lt Ctrl gt and lt Del gt to reboot your computer Follow steps under Recovering Windows 43 Chapter 4 System Software Windows XP Reinstallation Enter BIOS setup Set first boot device to CD ROM See Chapter 6 BIOS Settings Put the Recovery CD for Windows XP Disch into the CD ROM drive and reboot the computer When the CD Boot Menu appears choose option 1 Recovery CD for Windows XP When prompted insert the Disch It will take approximately five minutes to complete the installation Remove the CD ROM from the drive when the installation is complete Suggesting plug AC Adapter when Recovering Press lt Alt gt lt Ctrl gt and lt Del gt to reboot the computer Enter the BIOS Setup Utility and select Boot priority Reset the boot priority to either A or C While starting Windows reenter the Windows information as prompted 44 Chapter 5 Power Management m Z Q 7 I Chapter 5 Power Management Power Management Battery Calibration The first time you use a battery you should calibrate it The calibration process empties and charges the battery one time This allows the Windows battery gauge to accurately monitor battery status To calibrate a battery follow these steps 1 Plug inthe AC adapter 2 Restart the computer and when the startup screen appears press Del key to enter the B
42. r through any of the slots or openings Dangerous voltages are present which could cause electric shock or fire or damage sensitive components For best results use a power strip with a built in surge protector Do not use inferior extension cords as this may result in damage to your computer Introduction Checklists Set the computer on a flat stable surface To prevent damage to the computer e hard disk drive avoid using the computer where it will be exposed to strong vibration Checklists After opening the package carefully inspect the contents If any of the items is missing or appear damaged contact your dealer The shipping carton should contain the following STANDARD A notebook computer with a hard disk drive An internal battery A CD ROM DVD ROM Combo DVD RW drive An AC adapter with power cord User s Manual System software CD ROMs Anti electromagentic wave clip OPTIONS The following items are normally optional but some vendors may include them in the standard package Some items may not be available in some countries or some vendors may choose not to carry all the items 256 or 512 MB or 1G SO DIMM memory card A Carry bag An operating system manual Chapter 1 Introduction Caution When purchasing any of the accessories listed above purchase only those accessories that are approved for use with your computer The above accessories are proprietary items Your system vendor can obtain these app
43. rge amounts of data may wish to use backup devices such as a tape backup unit or a ZIP drive If you use your notebook as a networked workstation with system backup talk to the system administrator about backup procedures for your notebook 11 Chapter 1 Introduction Don t leave passwords anywhere on your notebook or carrying case Be careful when placing your notebook on an airport security conveyor belt In most airports security conveyor belts are safe for computers If you are not sure ask the security staff You should keep a close eye on your computer When you are in a hurry make sure that you walk away with the correct notebook computer Tape your business card to the notebook and accessories In the workplace notebooks and accessories may often look exactly alike leading to equipment mix ups Prevent such mix ups by placing your name on your equipment Develop ergonomic work habits The science of ergonomics studies the relationship between health and a suitable work environment For more information on ergonomics contact your nearest computer bookstore or local library The Internet also has information on this and other related subjects Never take the notebook anywhere without the carrying case A broken screen or case can be costly to repair Prevent accidents by carrying the computer in a suitable carrying case Consider using a lock For added security consider purchasing a Kensington lock to put in
44. roved accessories If you use items that are not approved for use with this computer you may cause your computer to malfunction or to emit or receive electro magnetic radiation in excess of local regulations For non proprietary accessories such as PC cards or printers ensure that the accessory functions properly in your computer before making the purchase Your system vendor may be able to recommend reliable brands and models Features High Capacity Hard Disk Drive The computer has a high capacity hard disk drive to store your favorite programs and large multimedia files Built in Modem LAN Capability A built in 56k modem and 10 100 1000 Mbps Ethernet port allows you to access the Internet or a local area network LAN Large LCD Your computer has an easy to view XGA SXGA LCD panel Built in Stereo Speakers and Microphone The stereo speakers and internal microphone enable you to run a variety of multimedia applications Convenient Audio Control The conveniently located audio control knob enable you to easily adjust the volume to the stereo speakers Function Keys Function keys give you easy control of power management and your monitor Scrolling Button Comfortably scroll through documents with the ergonomically designed scrolling button Introduction Where to Look For Information Where to Look For Information About Your Computer This User s Manual describes the key elements of your computer New
45. ry will automatically begin to recharge While the battery is charging the Battery Charge icon on the Indicator panel will be active after 6 12 seconds When the battery is fully charged the Battery Charge icon will turn to green If your computer is turned off a fully discharged battery will take about 3 5 hours to recharge If your computer is turned on and is not in suspend mode it twill take about 6 13 hours to recharge the battery Refer to the following table Charging System On 6 13 hours System Off 3 5 hours suspend to disc Note A fully charged Li Ion battery can run the Notebook for approximately 3 hours According to Battery Mark benchmark tests Power Saving Modes Adjust the default power management settings in the Power Options Advanced dialog box in the Control panel The Power Options Properties dialog box allows you to set different actions to take when the computer is left idle for a certain amount of time Suspend Mode There are several possible settings for suspend mode which can be selected in the Power Management dialog box You may have the 48 Power Management Power Saving Modes notebook standby hibernate or you can power off the computer altogether Standby Hibernate Power Off All devices are powered up and in suspend mode Suspend to Disk is similar to turning off the computer except that the current state of the computer is copied to the hard disk
46. s Hot Keys Rotation OpenGL Information 2 Double click Display J Devices The Display Properties Primary Device Monitor v window opens Monitor 3 Click the Settings tab pe zi 4 Click the Advanced Notebook EC Device Options button a 5 Click the Intel 4 Graphics Media ktam Dual IV Same display configuration driven on both displays Display Cl Accelerator tab The SE screen shown at the right appears Device Settings Cancel Apply These options are described below 29 Chapter 2 Getting Started In Display Combination there are six options available by pressing the Fn F2 keys Hot Key Switch cp CRTSLCD CRT gt TV gt LCD TV gt CRT TV LCD is the default value for Primary D Tip To ensure trouble free video output the first time you use an external monitor change the output in the Display Properties dialog box After successfully switching modes you may use the video function keys Note Light or dark dots may appear on the LCD due to technical limitations of LCD manufacturing This will not effect normal operation of the LCD 30 Getting Started Information about the Wireless LAN button Communication Components This system provides powerful communication functions including built in MiniPCI 802 11a b g and PCMCIA card slot Fax Modem A phone jack on the left side of the computer allows you to connect to the Internet to send and receive data
47. s keyboards and mice Refer to documentation included with individual devices for details on connecting these devices to your computer Along with the standard ports found on most computers your computer also includes IEEE 1394 ports modem and LAN ports offering advanced communications technology Left Side Connectors PTT TI 1 2 3 4 1 Kensington Lock Your computer includes a Kensington lock hole to be used with a standard Kensington lock You can connect the notebook to a large object with the Kensington lock to prevent theft of your notebook See the documentation that comes with your Kensington lock for more information 2 DC in Jack Connect the DC power cable from the AC adapter to this jack 3 VGA Out External Video Port The 15 pin VGA port can be used to connect your computer to an external monitor See the Graphics System in chapter 2 for more information 6 36 Making Connections Right Side Connectors 4 LAN RJ 45 Jack With the built in Ethernet LAN combo you can make LAN connections without installing PC cards Connection speed is 10 100 1000 Mbps When using the LAN function wrap your LAN cable around the EMI ferrite suppression box to inhibit electromagnetic interference 5 Fax modem RJ 11 Jack The fax modem can transmit data using the 56 Kbps V 90 protocol and send and receive faxes at 14 4 Kbps In some countries local regulations may not permit the use of the fax modem desig
48. se of this copyright production technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation Reverse engineering or disassembly is prohibited 74
49. t button is accidentally pressed when reading a CD When this happens please unlock the drive press eject and push the tray back into the computer before reading again 2 Warning When the computer is reading from a CD 23 Chapter 2 Getting Started Precautions for Handling CD ROM Discs Keep these precautions in mind when handling CD ROM discs Always hold the disc by the edges avoid touching the surface of the disc Use a clean dry cloth to remove dust smudges or fingerprints Wipe from the center outward Do not write on the surface of the disc Extremes in temperature may damage discs Store discs in a cool dry place Do not use benzene thinners or cleaners with detergent Only use CD ROM cleaning kits Do not bend or drop the discs Do not place objects on top of discs Warning Do not insert any foreign objects into the disc tray Do not force the tray to open or close manually When not in use keep the tray closed to prevent dust or dirt from entering the drive unit If you experience difficulty when removing a CD disc stretch a paper clip or use a pin ora thin metal rod and insert it into the emergency eject hole located on the front panel The CD disk tray should eject immediately This procedure can also be used to remove a CD from the drive when the notebook is powered off 24 Getting Started The PCMCIA Card Slot Connecting the Printer To connect a printer to your not
50. tion against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and the receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for help Shielded interconnect cables and shielded AC power cable must be employed with this equipment to insure compliance with the pertinent RF emission limits governing this device Changes or modifications not expressly approved by the system s manufacturer could void the user s authority to operate the equipment Declaration of Conformity This device complies with part 15 of the FCC rules Operation is subject to the following conditions e This device may not cause harmful interference e This device must accept any interference received including interference th
51. to the Kensington lock hole on the left side of your computer see Chapter 2 Left View Use the Kensington lock to secure the computer to a desk or table Note Using a computer for extended periods of time with a poor workstation setup and incorrect work habits can cause health problems 12 Chapter 2 Getting Started m rd O 7 I Chapter 2 Getting Started Hardware and Software This chapter introduces the different components and controls of your notebook computer including the hardware components the software and the audio and video systems Getting Started Before you begin using your computer read this chapter to familiarize yourself with the main components installed in the system First gently lift the cover using both hands and open up the computer 14 Front View QOS Et DDE LCD panel Battery Keyboard Speakers Touchpad Touchpad buttons Scrolling button Volume control knob Microphone in jack 10 11 12 13 14 15 16 17 Getting Started Left View Audio out jack for external speakers or headphones SPDIF jack IEEE1394 port Power indicators Microphone Activity indicators Power button Wireless LAN power button communications antenna is located in upper right hand corner of the cover A Warning The wireless Please avoid hitting it so communications quality will not be affected 15 Chapter 2 Getting Started Left Vi
Download Pdf Manuals
Related Search