Plimmer Cubetto Delta Plus User manual
Contents
1. sueerra Plimmec DELTA PLUS Operation and maintenance user manual Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification Operation and maintenance manual 1 Introduction 1 1 Preliminary inspection 1 1 1 CoVisual check 1 1 2 Materials handling and storage 1 2 Warranty 1 3 Applications 2 Important safety information 2 1 Protection against freezing 3 Technical data 4 Assembling 4 1 Installation 4 2 Power supply 5 Start up 5 1 Initial start up 6 Cubetto main panel 6 1 Multicolor led colors 7 How it works 7 1 Quick start 7 2 Cubetto features 7 3 Panel for debug mode 8 Maintenance 8 1 Maintenance 9 Technical schematics 9 1 Plimmer plumbing connection Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification 1 General The purpose of this manual is to provide the necessary information for the installation use and maintenance of the Plimmer the user should read this manual before using the Plimmer Improper use could damage the Plimmer and will re2. 90 UV lamp finished Lack of water Check if the water z z Repeated lack of water is present and resetthe equipment Generic tauk Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification 7 How it works Keyboard unlock To avoid wrong usage by the user when no key is pressed for 120 seconds keyboard will lock and no key pression is recognized To unlock the keyboard you have to press simultaneously the following 3 keys Water quality Select Confirm cane If unlock is recognized all the lights will flash for a while 7 1 Quick start Plimmer Cubetto comes with default settings that can be changed as follows POWER INTERRUPTION Plimmer is a device using an electrostatic field to remove salts from water For this reason it is very important that it remains powered continuosly and with no high or under voltage We recommend to connect the Cubetto to a protected power source otherwise buy a UPS and connect the Cubetto to it PLIMMER POWER OFF To disconnect power source from Cubetto wait to have led 7 see paragraph 7 3 on If this condition is not respected you may damage the equipment Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are re
3. Cubetto main panel Figure 2 1 Water quality regulation 2 Standby on off 3 Select 4 Confirm 1 3 4 Keyboard unlock 5 Function light 6a Alarms 6b Plimmer state lights See paragraph 7 2 7 Safe power off indicator 8 Time 9 Extra antifouling cycle 10 Water hardness selection 11 Not used 12 Filter cartridge 13 Maintenance solution 14 Disinfecting solution if available Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification 6 1 Multicolor LED combinations 0 peration Normal operation Tank filling lst stage Normal operation Tank full Qudet closed Normal operation 2nd stage production Antifouling ocle Spedal regeneration for 2nd stage Rev 1 0 ENG 29 06 2012 Multicolor LED cambinations u betto multicolor rontal led rules the current machine status Status under green column defines normal operation the ones in the orange columns a user interaction while the one in the zone involve an authorized technician User interaction Technical assistance Maintenance solution lifecycle gt 90 Maintenance solution finished Filter cartridge lifecycle 90 Filte r cartridge finished UW lamp lifecycle gt
4. and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification 9 Tecnichal schematics 9 1 Plimmer plumbing connections In the case the Plimmer were connected to a public water supply a retaining valve can be installed Verify the local regulations DRAIN OUT WATER INPUT Figure 3 Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification
5. different applications e Cubetto Delta Plus can treat water with maximum inlet conductivity of 2000 uS with a salt rejection up to 90 99 variable in relation of the inlet conductivity water composition and operation flow e Is certified in Europe for human water consumption e Reduce bacterial charge e It is suitable to replace an ion exchange water softener avoiding periodic maintenance and salt consumption e To remove Nitrates Arsenic and organics contaminants from drinking water Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification 2 Important safety information The user should read this manual before using the Plimmer Improper use could damage the Plimmer and will result in your warranty becoming void The following instructions and warnings refer to the standard model for any variations or characteristics of the special versions please refer to the sales contract For any instructions or situations not referred to in this manual or in the sales documentation please contact our sales service Addtionally please observe security and industrial safety regulations 2 1 Protection against freezing Plimmer is a machine that treats and contains water For this reason install and stor
6. making a claim under this warranty If in the event the receipt of purchase is not presented then this warranty is invalid 3 SERVICE OR REPLACEMENT DURING THE WARRANTY PERIOD 3 1 In the event that Plimmer is Dead On Arrival DOA the owner has 14 days in which to return the Product to the retailer or place of purchase for a new replacement If the owner does not return the product within 14 days then the Product will be treated under normal warranty conditions 3 2 Under normal warranty conditions the product must be returned to the Retailer place of purchase or any IDROPAN DELL ORTO DEPURATORI SRL Service Centre in the country of purchase 3 3 Please ensure that the product is properly packaged so as to ensure that no damage occurs to the product during transit Also make sure you have included an explanation of the problem 3 4 In the event that the goods requiring repair under warranty the owner is responsible for the cost of transportation to and from the service centre Whilst in transit the goods are at the owners risk Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification 4 GENERAL EXCLUSIONS AND LIMITATIONS 4 1 In the event that no identical Product is available for service repair
7. 50 ppm TDS water Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification 5 Start up 5 1 Initial Start up Check plumbing and electrical connections We advise to let water pass freely for a few minutes before connecting fittings UAMH Plimmer might be subject to water hammer due to the air in the tubes during the first working minutes We advise to reduce the operating pressure for the first 10 minutes Verify that all pipes are well connected and that there are no leaks When the Plimmer is switched on for the first time it should be in production BEFORE the water taps are opened When the Plimmer is ready to produce partially open the entry valve in order to verify the presence of any leaks Let the machine work at a reduced flux level for at least 10 minutes and then gradually bring values to idle operating levels it is advisable to drain the water produced in the first 30 60 minutes Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification 6
8. IDROPAN DELL ORTO DEPURATORI SRL has the right to replace the Product with a device of equal capacity or offer the customer the choice of a Product upgrade which may incur an extra cost 4 2 This warranty is limited to defects in workmanship or parts All defective products or parts will be repaired or replaced This warranty does not extend to accessories This warranty does not cover manuals and packaging line cords or wiring 4 3 This warranty does not cover consumable items 4 4 This warranty does not cover any defect caused by an accident misuse abuse improper installation or operation lack of reasonable care unauthorised modification loss of parts tampering or attempted repair by a person not authorised by the distributor 4 5 The warranty will not apply if the factory applied serial number has been altered or removed from the Product 4 6 The warranty will not apply if damage malfunction or failure resulting from alterations accident misuse abuse fire liquid spillage maladjustments of customer controls use on an incorrect voltage power surges and dips thunderstorm activity acts of God voltage supply problems tampering or unauthorised repairs by any persons use of defective or incompatible accessories exposure to abnormally corrosive conditions or entry by any insect vermin or foreign object in the Product 4 7 This warranty does not cover damage arising during transportation installation or while moving t
9. ace the cartridge in the following way With the select key go until 8 Press confirm key EN All the leds will start flashing Wait until the become continuosly on Replace the cartridge mounting and umounting by turn Press the confirm key MAINTENANCE SOLUTION BOTTLE WARNING STOP Maintenance bottle life is limited At 90 of its lifecycle led E start flashing and the machine still operates At the end of its lifecycle instead the machine stops working because it can not guarantee anymore correct functioning It is important to replace the cartridge in the following way With the select key Bideo until 2 Press confirm key l 4 All the leds will start flashing Replace the bottle Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification Press confirm key Leds will stay on for a while they will switch off and recover normal operation of the equipment UV LAMP WARNING STOP At 90 of UV lamp lifecycle Alarm led 2 start flashing At the end of its lifecycle instead the machine stops working because it can not guarantee anymore correct functioning For the replacement you have to call an authorized technician PUMP MODE SELECTION To increase CO
10. e the Plimmer in places where temperatures do not allow water to freeze If this happens iK a EAL x Clute ke Cate Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification 3 Technical Data e Partial demineralizing machine with Plimmer technology Maximum day production at 25 C 1 000 1 600 litres day based on requested conductivity Maximum hourly flow at 25 C 50 80 litres hour Productivity and salt removal based on requested conductivity Average power consumption 100W Dimensions mm 850 h x mm 530 x mm 620 e Tank Total volume 91 litres Useful volume 80 litres e Sterilizer with UVC lamp complete with shield UV transparent made in glass PVDF Power 18 W e High efficiency submersed pressurization pump with analog pressure sensor made by stainless steel Maximum pressure 3 2 Bar Maximum pressure at 30 litres minute 2 8 Bar Power 0 25 Kw e Pressure accumulator tank 4 litres e Bistable bypass valve to ensure direct water suppli in case of power outage or excessive water consumption e Intended for drinking domestic usage e Certified e Maximum inlet water conductivity 2000 uS e Advanced tank functions e Integrated filter e Ease of use e Smart functions e Plug amp Play A
11. et second cipher of minutes between 0 and 9 yellow led When the right value is set press the ON OFF key 6 red leds will switch on 1 2 3 4 5 and 6 alarm zone You can now choose between If you want to start again press ON OFF key If you press confirm key you set the values for maintenance and system time Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification 7 2 Cubetto features EXTRA ANTI FOULING CYCLE To make an extra antifouling cycle press selection key x till the third icon Press confirm key to start STAND BY FUNCTION You can activate stand by function by simultaneously pressing the select key and the ON OFF key If everyting is ok multicolor led will become flashing blue This function is useful to keep the Cubetto clean during inactivity periods Power must be kept for the whole period To get back in normal operation mode press simultaneously the select key and the ON OFF key FILTER CARTRIDGE WARNING STOP Filter cartridge life is limited At 90 of its lifecycle led 8 start flashing and the machine still operates At the end of its lifecycle instead the machine stops working because it can not guarantee anymore correct operation It is important to repl
12. gistered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification WATER HARDNESS REGULATION Water hardness defines its tendency to foul Plimmer has an automatic system to avoid fouling inside the cells it is needed to set the value To make the regulation Unlock the keyboard Press the select key until position 10 Press the confirm key t Green led 10 will glove and on the bottom line also some yellow lights will switch on Using select key choose the right hardness value step of 5 FH example to select 25 FH switch on 5 lights measured in Frech hardness degrees Press the confirm key NOTE Fouling capacity of water changes even with the same hardness based on water composition temporary hardness and permanent hardness presence or absence of strong anions such as chlorides solfate and nitrates In case of high fouling water almost made up of bicarbonates temporary hardness and small quantity of strong anions chlorides sulfates nitrates we recommend a value greater than at least 1 2 shots Regulation range is between 15 and 60 we remind you that Plimmer maximum hardness accepted is 50 FH Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other t
13. he Product or to any transportation costs of the Product or any parts thereof to and from the owner unless otherwise specified in these warranty conditions 4 8 This warranty does not apply whilst outside the country of purchase 4 9 IDROPAN DELL ORTO DEPURATORI SRL will not be liable for any loss damage or alterations to third party furniture hardware or software or programs data or information stored on any media or any part of the Product no matter how occurring or for any loss or damage arising from loss of use loss of profits or revenue or for any resulting indirect or consequential loss or damage 4 10 IDROPAN DELL ORTO DEPURATORI SRL s aggregate liability in respect of all claims under the Warranty shall not exceed the original purchase price of the Product or at IDROPAN DELL ORTO DEPURATORI SRL s option the cost of replacing the Product 4 11 This warranty does not cover normal wear and tear of the Product or parts 4 12 IDROPAN DELL ORTO DEPURATORI SRL excludes all other warranties conditions terms representations and undertakings whether express or implied Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification 1 3 Applications Plimmer Cubetto Delta Plus can be used in
14. ll in one machine Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification Figure 1 Idropan dell Orto riserve the right to modify or change the tecnica and aesthetic characteristics of all equipment Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification 4 Assembling Accessories may defer according to local regulation Please make sure that you follow these correctly 4 1 Installation examples Cubetto machines are made to simplify setup and startup Plumbings connection are 3 with male 3 4 thread Equipment is supplied with 3 meters of power cable and requie a 220V power supply 4 2 Electricity supply Plimmer demand an electricity supply that according with the different models could be 220V monophase Earthing TABLE OF ELECTRICAL CONSUMES Average power consumption 150 160 W Peak power consumption 750 780 W Power consumption is related to water salinity and effective flow Reported values are calculated on a 2
15. opyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification LED WEIGHT FUNCTION 1 20 2 40 Show the percentage of the current phase 3 60 For short phases led will increment quickly 4 80 5 1 6 2 Phase number espresse as binary number 7 4 8 8 Red lights 1 6 Alarm zone CONDITION 1 2 3 4 5 Wait X Powering on X Q Working X 3 D Shutting off X Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification 8 1 Maintenance Plimmer is a machine that does not need large amounts of maintenance However it is possible due to inappropriate discharge water value adjustments that calcium carbonate precipitates on the cell electrodes The condition above is very easy to spot the user will notice The flow will reduce The quality of the water will reduce In this case the maintenance process with citric acid is necessary Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD
16. rademarks are registered by their respective owners All the data can change without notification MAINTENANCE TIME SET AND TIME SET Press the select key until Time icon position on the bottom line Press the confirm key E A sheen light will switch on over the Time icon and a red light will switch on over the 1 alarm zone At this moment it is possible to set time for antifouling maintenance and sanitizing maintenace Bottom line shows a maximum of 12 yellow leds and the last led on the right means AM or PM led on Regulation can be done with one hour step Following is to set time to have Plimmer clock synchronized with real time When maintenance time is set you can choose If you do not want to set system time press confirm key iat to exit l If you want to set system time press ON OFF 2 red leds will switch on 1 and 2 alarm zone and it is possible to set first cipher of hour between 0 and 2 yellow led When the right value is set press the ON OFF key 3 red leds will switch on 1 2 and 3 alarm zone and it is possible to set second cipher of hour between 0 and 9 yellow led When the right value is set press the ON OFF key 4 red leds will switch on 1 2 3 and 4 alarm zone and it is possible to set first cipher of minutes between 0 and 5 yellow led When the right value is set press the ON OFF key 5 red leds will switch on 1 2 3 4 and 5 alarm zone and it is possible to s
17. removal it is possible to spray water inside the tank during operation To enable disable the pump follow the procedure Move under number 5 with select key Press confirm key j Led will stop flickering for a while and led 5 will stay on or off Led off Pump off Led on Pump on Now working mode will swap and led will confirm it for three seconds System will automatically exit from function Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification 7 3 Panel for debug mode Based on lights showed in Figure 2 point 6b main panel show equipment status There are 3 modes 5 6 Function Meaning OFF OFF Status See description OFF ON Out pressure 1 Led 0 4 Bar ON ON Tank level 1 Led 10 STATUS MODE 1 FAILURE BYPASS UV KR U N ANTIFOULING ul SANITIZING POWERING ON WORKING SHUTTING OFF oO Oo N QA WAIT 10 ON OFF KEY There is a more advanced diagnostic view that can be activated in the following way Unlock the keyboard With the selection key go to the last position Press confirm key This view will last till select key press that will recover back Plimmer in normal operation mode Rev 1 0 ENG 29 06 2012 C
18. sult in your warranty becoming void When asking our sales and after sales services for technical information or spare parts please indicate the model identification and construction numbers found on the nameplate The following instructions and warnings refer to the standard model for any variations or characteristics of the special versions please refer to the sales contract For any instructions or situations not referred to in this manual or in the sales documentation please contact our sales service 1 1 Preliminary inspection 1 1 1 VISUAL CHECK Upon delivery check the integrity of the packaging After unpacking the Plimmer make sure that no damage has occurred during shipping Should the Plimmer be damaged please inform our agent within 8 days from the delivery date 1 1 2 MATERIALS HANDLING AND STORAGE The product must be handled with care impacts can cause damage without any visible external signs During shipping and handling protect Plimmer against wet freezing and physical damage Rev 1 0 ENG 29 06 2012 Copyright Notice 2011 Idropan Dell Orto Depuratori s r l IDD and Plimmer are registered trademarks by Idropan Dell Orto Depuratori s r l All the other trademarks are registered by their respective owners All the data can change without notification 1 2 Warranty STANDARD WARRANTY TERMS AND CONDITIONS 1 GENERAL TERMS AND CONDITIONS 1 1 Plimmer has been manufactured to the highest quali
19. ty standards and is warranted to the original purchaser recipient only This warranty is not transferable 1 2 The product is guaranteed to be free from defects in workmanship and parts for a period of 12 months from the date of purchase Defects that occur within this warranty period under normal use and care will be repaired or replaced at our discretion solely at our option with no charge for parts or labour 1 3 IDROPAN DELL ORTO DEPURATORI SRL reserves the right to replace the Product or relevant part with the same or equivalent product or part rather than repair it Where a replacement is provided the Product or part replaced becomes the property of IDROPAN DELL ORTO DEPURATORI SRL IDROPAN DELL ORTO DEPURATORI SRL may replace parts with refurbished parts Replacement of the Product or a part does not extend or restart the Warranty period 1 4 The benefits conferred by this warranty are in addition to all rights and remedies in respect of the product that the consumer has under the Trade Practices Act and similar state and territory laws 1 5 The Warranty is transferable to a new owner in the event of sale of the Product provided the new owner has the receipt of purchase and the Product is still within the guaranteed period 2 PROOF OF PURCHASE 2 1 Please keep your purchase docket or receipt as proof of purchase and as proof of the date on which the purchase was made The purchase docket or receipt must be presented when
Download Pdf Manuals
Related Search