Instructions Manual Clasus Interactive Board, Video - AV
Contents
1. the Interactive Board on the stand and make sure the upper attachment point matches the attachment point of the IB 11 Fix the IB to the stand using the two screws available on the back of the IB fastening it from back to front and between the stand and the IB at the position according to the below illustration 12 Remove the external control keyboard from the video projector Optional To remove the control keyboard Find the screws in the below edge of the control keyboard Unfasten the screws Remove the video projector control keyboard After removing the video projector control keyboard use the supplied rubber cover to protect the keyboard contacts 13 Fix the Video projector setting cover to the video projector using the three indicated positions 14 Fix the video projector setting cover with the video projector to the sustentation arm through the three indicated positions 15 Connect the RS 232 interface to the IB 18 16 Connect the VGA and audio cables to the video projector VIDEO S VIDEO D SUB OUT 17 18 Connect the VGA cable to the computer graphic card and the USB RS 232 cable to one available USB port 19 Turn on the computer 20 Turn on the video projector and using the remote control select D Sub Comp as source D Sub Comp aw E UVA DvD a Video S Video NOTE For more information s about the video proj2. Instructions Manual Clasus Interactive Board Video Projector and Height Adjustable Stand Vers o 1 1 2008 Legend Instructions additional instructions Q Note Problems that could occur and how to avoid them 4 Warning Circumstances to avoid as could result in damage Previous Considerations A Even if powered only with low voltage to reduce the risk of fire or electric shock do not expose your Clasus Interactive Board to rain or moisture Please make sure that your Clasus Interactive Board is firmly attached to the wall or stand before using it Keep your Clasus Interactive Board away from direct sunlight Read the safety warnings and precautions published by the projector manufacturer Do not stare or allow others to stare directly into the projector s projection beam You can use water ink based dry pen to write on your Clasus Interactive Board Do not never use abrasive or corrosive products to clean An wet tissue should be enough to the worst cases Do not never use permanent markers on you Clasus Interactive Board surface Avoid to scratch the frontal surface of your Clasus Interactive Board with cutting or sharp objects Apply the adequate force when working with the digital pen on the Clasus Interactive Board Do not never allow infiltrations of any kind of liquids or dust in your Clasus Interactive Board Table of Contents P gina glogo lu CHOU ree PC PE 4 PreparingInstallatlolis ies e
3. e you should find 1 One Clasus Interactive Board CiO Z UN 1 1 Accessories Components list component aum DVD Software A MIGO V1 0 2 0 Stands Wall mount stand Video projector sustentation arm Video projector setting cover Nuts Hex socket screws Hex screws Phillips screw Wall plugs 3 0 Video projector Model Included accessories BENQ MP771 User manual Quick initiation guide User manual in the CD Remote control Batteries for RC O 00 Co ouro e o Transport luggage VGA Cable USB Cable PWR Cable o Necessary Equipment To install the CLASUS solution you will need the following tools Drill Side cutters Socket wrench set Drill bits 6mm Hexagon keys Slotted screwdriver Hammer JO Z S Tape measure Combination pliers Double open ended wrench 10mm Pencil Utility knife Phillips screwdriver Carpenter s level Installation Before starting make sure the installation place is cleared from any object that could harm the normal installation procedure Also verify if any electrical cable or specific pipes are fixed inside the wall and move the drilling position in way to avoid any contact with them Make sure the wall is tough enough to securely hang the Interactive Board stand The following list of procedures illustrates the Interactive Board IB stand assembly process in a wall 1 Using t
4. ector usage please read the user manual included in the CD that comes with it 21 Using the two regulation areas available over the video projector or the keystone function of the video projector centre the image projected to the IB a Using the two regulation areas available over the video projector i Use it whenever the projected image is not vertically or horizontally within the IB area Examples b Using the keystone function of the video projector i Use it whenever the projected image assumes a trapezoidal format Examples 20 22 Insert the security lock for protection against stealing attempts of the video projector You can also apply the Kensington type cable optional 23 Final arrangements Optional For a better appearance of the final solution and cables protection consider the use of trunking and the correspondent necessary accessories 21 24 IB height regulation 25 Final testing After concluding all the installation process test the whole installed solution to make sure all its components are working properly and securely CLASUS solution installation process ended 22
5. he pencil and the tape measure draw a vertical line in the wall centred in the middle of the future Interactive Board position 2 The first position to mark on the wall must be coincident with the bottom left fixation position of the stand according to the below measures Horizontal starting from the middle point centred in the wall 54 cm a Vertical 80 cm b 3 Next using the correspondent tool drill on the marked position just the first of four and proceed by applying the wall plugs and the hex screws 4 Place the IB stand supported by the bottom left fixation position Assisted by a second person and using the carpenter s level set the stand correctly and mark the remain fixation positions 5 Remove the stand and complete the remaining three marked positions following the indications described for the first one 6 Place the stand lined up with the four fixation positions and fasten all the four screws Ensure there weren t any changes with the stand levelling 7 Place the VGA Audio and Power video projector cables inside its sustentation arm 8 Place the video projector sustentation arm in the Clasus Lift stand making it steady using the correspondent screw 9 Place the USB RS 232 cable in the stand Make sure to leave the RS 232 interface on the IB side and the USB to connect on the computer 10 Install
6. xeun E M RPM RENE A PERDE EU 5 Necessary EQUIDMEN ssa eic ceteaiiswtcesscewenignesesca fia sa inicia ana 9 lg cirs rsid o tr Er 10 Introduction Your CLASUS Interactive Board is a product of raised quality that uses the best available technology providing and efficient work environment In fact the use of the Wireless Electromagnetic technology is the key factor that allows a work speed up to 6 meters per second throughout an area with 77 inches of diagonal length combined with an exterior resolution up to 205 lines per inches Using the CLASUS Interactive Board combined with a video projector and a desktop or notebook computer you can make the difference when making your presentations guide your lessons or carries through your meetings Making full use of this set harnessing the Interactive and Multimedia concepts is a tremendous opportunity to go far beyond levels never before achieved Typical Assembly and use Scheme Projector QUADRO CLASUS QUADRO CLASUS REMOTO Projector Internet Imprimir A4 PC Remoto Guardar Automaticamente System Requirements Microsoft Windows version Minimal configuration Recommended configuration Hardware CPU 1GHz CPU 1 7 GHz RAM 128 MB RAM 256 MB Software Windows 2000 XP Vista Windows 2000 XP Vista Microsoft Internet Explorer 6 0 0 Microsoft Internet Explorer 6 0 0 Firefox 2 x Firefox 2 x Preparing Installation In your Clasus Interactive Board packag
Download Pdf Manuals
Related Search