Variable speed drives Altivar 12
Contents
1. m Drive with heatsink for normal environments and fan cooled enclosure O 100 120 V single phase 0 18 kW 0 25 HP to 0 75 kW 1 HP ATV12HeeeF 1 o 200 240 V single phase 0 18 kW 0 25 HP to 2 2 kW 3 HP ATV12HeeeM2 o 200 240 V three phase 0 18 kW 0 25 HP to 4 kW 5 HP ATV12HeeeM3 m Drive on a base plate for mounting on the machine frame the frame surface area should allow heat to dissipate o 100 120 V single phase 0 18 kW 0 25 HP to 0 37 kW 0 5 HP ATV12H018F1 P037F1 o 200 240 V single phase 0 18 kW 0 25 HP to 0 75 kW 1 HP ATV12H018M2 PeeeM2 o 200 240 V three phase 0 18 kW 0 25 HP to 4 kW 5 HP ATV12H018M3 PeeeM3 Note The Altivar 12 drive output voltage is 200 240 V three phase regardless of the type of drive line supply The Altivar 12 drive integrates as standard the Modbus communication protocol which can be accessed via the RJ45 connector located on the underside of the drive 1 witha 2 wire RS 485 physical interface To communicate on the network the Altivar 12 speed drive uses the Modbus RTU transmission mode For more information on the complementary characteristics of the Modbus port transmission speed address messaging please consult our website www schneider electric com The entire range conforms to international standards IEC EN 61800 5 1 and IEC EN 61800 3 is UL CSA C Tick NOM GOST certified and has been developed to meet the requirements of directives regarding the protection of2. 1 Heating Ventilation and Air Conditioning More technical information on www schneider electric com Altivar 212 variable speed drives Schneider Electric 0 75 90 1 125 OVD IO 4 120 IP 54 _ Equipped with a Vario switch disconnector 0 1 599 Hz from 0 75 to 45 kW 7 60 HP 0 1 500 Hz from 55 90 kW 75 125 HP Sensorless flux vector control Voltage frequency ratio 2 or 5 points Energy saving ratio Vector control without speed feedback 110 ofthe nominal motor torque for 60 seconds gt 100 4 20 o mO 4 YIS eNe Modbus and CANopen Modbus TCP Daisy Chain Modbus Uni Telway EtherNet IP DeviceNet PROFIBUS DP VO and V1 InterBus CC Link LonWorks METASYS N2 APOGEE FLN BACnet I O extension cards Controller Inside programmable card multi pump cards encoder interface cards IP 54 or IP 65 remote graphic display terminal SoMove Simple Loader Multi Loader 0 75 75 1 100 Oo 100 Equipped with a Vario switch disconnector 0 1 599 Hz from 0 75 to 37 kW 1 50 HP 0 1 500 Hz from 45 to 75 kW 60 700 HP Sensorless flux vector control Voltage frequency ratio 2 or 5 points ENA System Vector control with or without speed feedback 220 ofthe nominal motor torque for 2 seconds 170 for 60 seconds gt 150 220 u u eN o w Modbus TCP Daisy Chain Modbus Uni Telway EtherNet IP DeviceNet PROFIBUS DP VO and V1 InterBus CC Link Interface c
3. Controller Inside programmable card IEC 61800 3 environments 1 and 2 categories C1 to C3 IEC 61000 4 2 4 3 4 4 4 5 4 6 4 11 C UL CSA DNV C Tick NOM GOST ATV 61 ATV 71 Altivar 61 variable speed drives Altivar 71 variable speed drives 2 The type of cooling depends on the model Please consult pages 16 and 17 Qu More technical information on www schneider electric com Schneider Electric Selection guide IP 54 or IP 55 variable speed drives for asynchronous and synchronous motors 0 18 15 0 25 20 DES 20253 07215 0920 Pos Enclosure user definable up to 4 kW 5 HP Vario switch disconnector LEDs selector switch potentiometer 0 1 500 Hz Sensorless flux vector control Voltage frequency ratio 170 200 of the nominal motor torque Modbus and CANopen Modbus TCP Fipio PROFIBUS DP DeviceNet IP 65 remote terminal SoMove Simple Loader 0 75 75 1 100 ON Deo a i100 IP 55 01 2002 Sensorless flux vector control Voltage frequency ratio 2 points Energy saving ratio 120 of the nominal motor torque for 60 seconds 2 O N Y Modbus METASYS N2 APOGEE FLN BACnet LonWorks IP 54 or IP 65 remote graphic display terminal PCSoft for ATV 212 drive Multi Loader IEC 61800 5 1 IEC 61800 3 environments 1 and 2 categories C1 to C3 C UL CSA C Tick GOST ATV 31C ATV 212W Altivar 31C variable speed drives
4. 72x 143 x 121 2 ATV12H055M2 H075M2 HO75M3 72 x 189 5 x 131 2 72 x 143 x 131 2 5 ATV12H075F1 HU15M2 HU22M2 105 x 188 2 x 156 2 105 x 142 x 156 2 5 ATV12HU15M3 HU22M3 105 x 189 3 x 131 2 105 x 143 x 131 2 ATV12HU30M3 HU40M3 140 x 230 6 x 141 2 140 x 184 x 141 2 1 These values are given for a nominal switching frequency of 4 kHz for use in continuous operation If operation above 4 kHz needs to be continuous the nominal drive current should be derated by 10 for 8 kHz 20 for 12 kHz and 30 for 16 kHz The switching frequency can be set between 2 and 16 kHz for all ratings Above 4 kHz the drive will reduce the switching frequency automatically in the event of an excessive temperature rise ATV12HU15M2TQ 8 See the derating curves in the User Manual available on our website at www schneider electric com 2 Typical value for the indicated motor power and for the maximum prospective line Isc 3 Weight of product without packaging 4 Min U1 and max U2 nominal supply voltage 100 U1 120 V U2 200 U1 240 V U2 5 Due to the poor heat dissipation the ATV12H018ee drive is only supplied as a base plate version 6 This drive is delivered with a disconnectable category C1 EMC filter This drive complies with the IEC EN 61800 3 standard Environment 1 public network category C1 at 2 4 8 12 and 16 kHz for a shielded motor cable length inferior or equal to 5 m 7 Complies with the IEC EN 61800 3 standard Envir
5. GV2L20 18 gt 100 4 pole C60N 20 10 3 ATV12eU30M3 GV2ME21 17 23 50 LC1D25 M1 GV2L22 25 50 200 240 V three phase asynchronous motor 4 pole C60N 20 10 4 5 ATV120U40M3 GV2ME32 24 32 50 LC1D25 Motor starter with three phase power supply GV2L22 25 50 4 pole C60N 32 10 6 25 A si 30 mA 10 25 A si 30 mA 16 25 A si 30 mA 20 25 A si 30 mA 32 40 A si 30 mA Recommendations for special uses m All RH10 RH21 RH99 RHU residual current protection devices with separate sensors are compatible as long as the type and sensitivity of the add on modules given in the table above are observed m Itis advisable to connect one RCD residual current device per drive In this case a type B RCD must not be located downstream of a type A or AC RCD 1 For a complete list of references for TeSys contactors please refer to the Motor starter solutions Control and protection components and Motor starters up to 150 A catalogues or visit www schneider electric com 2 Motor power indicated for combination with an ATV12Heeeee drive with the same rating For combination with an ATV12Peeeee drive refer to the specific manual for the Altivar 12 base plate version available on our website at www schneider electric com 3 TeSys motor circuit breakers GV2MEee Thermal magnetic motor circuit breakers with pushbutton control GV2Lee Magnetic motor circuit breakers with control by rotary knob 4 4 po
6. R 150 Q 4 T VW3A8306R 0 010 with connection via splitter box and RJ45 connectors Description of the Motion amp Drives Offer DVD ROM ATV12000000 VW3A8200 0 100 Contents 6 m Technical documentation m Catalogues m Brochures Fans ATV12H075F1 VZ3V1301 0 160 ATV12HU15M2 HU22M2 ATV12HU15M3 HU40M3 VZ3V1302 0 150 VZ3V1302 1 Motor cable length given for a switching frequency of4 kHz 2 Please refer to the Twido programmable controller catalogue 3 Cable depends on the type of controller or PLC 4 Order in multiples of 2 5 Depends on the bus architecture 6 The content of this DVD ROM is also available on our website at www schneider electric com Drives Accessories Configuration Options Motor starters page 16 page 18 page 19 page 20 page 22 Electric Schneider Combinations for customer assembly Variable speed drives Altivar 12 Motor starters Single phase supply voltages 100 120 V and 200 240 V The proposed combinations can m Protect people and equipment when a short circuit occurs m Maintain protection upstream of the drive in the event of a short circuit on the power stage Two types of combination are possible m Drive circuit breaker Minimum combination m Drive circuit breaker contactor Minimum combination with contactor when a control circuit is needed M1 A1 Q1 KM1 Single phase suppl
7. schneider electric com The information provided in this documentation contains general descriptions and or technical characteristics of the performance of the products contained herein This documentation is not intended as a substitute for and is notto be used for determining suitability or reliability ofthese products for specific user applications It is the duty of any such user or integrator to perform the appropriate and complete risk analysis evaluation and testing ofthe products with respect to the relevant specific application or use thereof Neither Schneider Electric nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein Design Schneider Electric Photos Schneider Electric Printed by January 2013 V1 0 DIA2ED2130101EN
8. which provide a high quality drive from the very first time the power is turned on The integration of Standard U f Performance sensorless flux vector control or SVC and Pump Fan quadratic profile Kn control profiles High dynamic performance on acceleration as well as on braking Excellent speed regulation on machine load surges e Reduced noise and maintenance No fan on models up to 0 75 kW at 240 V Cassette type fan operates automatically on detection of specific temperature setting e Designed for easy fitting and wiring of the drive A single tool Power terminals not tightened ready for wiring Easy access angles Numerous easy to identify markings e Fast detection and protection against the motor current peaks associated with certain applications motor switching catching on the fly etc e Perfect integration of single phase 240 V model into the electrical network thanks to its built in EMC filter The fan which is the only wearing Practical recyclable packaging You can part can be changed without the configure your product in its packaging need for any tool without breaking the guarantee seal Ecological e An average of 30 energy savings with the Pump Fan control profile for the majority of applications e Less cardboard to be recycled only one box is used for bulk orders Sturdy e New generation long life compo nents 10 year service life under normal operating conditions Cards a
9. 8M3 5 0 700 3 6 3 1 2 5 2 4 3 6 24 ATV12P037M3 6 0 700 6 3 5 3 2 2 5 4 2 6 3 41 ATV12P075M3 6 0 700 11 1 9 3 3 9 5 7 5 11 2 73 ATV12PU15M3 6 1 000 14 9 125 5 5 10 15 85 ATV12PU22M3 6 1 000 19 159 6 6 5 12 2 18 3 94 ATV12PU30M3 6 1 600 23 8 199 83 5 16 7 25 128 ATV12PU40M3 6 1 600 Dimensions overall ATV12P037F1 ATV12P037M2 P075M2 72 x 189 5 x 102 2 72 x 143 x 102 2 ATV12P037M3 P075M3 ATV12PU15M3 PU22M3 105 x 189 3 x 98 2 105 x 143 x 98 2 ATV12PU30M3 PU40M3 140 x 230 6 x 100 2 140 x 184 x 100 2 1 These values are given for a nominal switching frequency of 4 kHz for use in continuous operation If operation above 4 kHz needs to be continuous the nominal drive current should be derated by 10 for 8 kHz 20 for 12 kHz and 30 for 16 kHz The switching frequency can be set between 2 and 16 kHz for all ratings Above 4 kHz the drive will reduce the switching frequency automatically in the event of an excessive temperature rise See the derating curves in the User Manual available on our website at www schneider electric com 2 Typical value for the indicated motor power and for the maximum prospective line Isc 3 Weight of product without packaging 4 Min U1 and max U2 nominal supply voltage 100 U1 120 V U2 200 U1 240 V U2 5 Due to the poor heat dissipation the ATV12H018ee drive is only supplied as a base plate version 6 To size the ATV12Peeeee driv
10. A9524 0 190 ATV12HU15M2 HU22M2 ATV12HU15M3 HU22M3 ATV12PU15M3 PU22M3 ATV12HU30M3 HU40M3 VW3A9525 0 210 ATV12PU30M3 PU40M3 PF080667A 15 V 24 V voltage converter ATV12000000 VW3A9317 ll WE o Connects directly to the control terminals VW3A9524 Dimensions overall VW3A9804 77 5 x 143 6 x 37 9 VW3A9805 105 x 144 x 40 Drives Accessories Configuration Options Motor starters page 16 page 18 page 19 page 20 page 22 ES Schneider PF100898C References continued TCSWAAC13FB Configuring the drive in its packaging with the Multi Loader tool VW3A8121 cordset VW3A8126 Drives page 16 Variable speed drives Altivar 12 Configuration tools SoMove lite setup software and associated accessories SoMove lite setup software ATV12000000 1 For configuring adjusting and debugging the Altivar 12 drive Downloadable from our website www schneider electric com or available on the Description of the Motion amp Drives Offer DVD ROM VW3 A8 200 USB RJ45 cable ATV12000000 TCSMCNAM3M002P equipped with a USB connector and an RJ45 connector For connecting a PC to the Altivar 12 drive Length 2 5 m Modbus Uni Telway Bluetooth adaptor ATV12000000 TCSWAAC13FB For establishing a Bluetooth wireless connection between the Altivar 12 drive and a PC equipped with a Bluetooth wireless link Pack contents m 1 Bluetooth adaptor range 20 m class 2 with an RJ45
11. Drives Accessories Configuration Options Motor starters page 16 page 18 page 19 page 20 page 22 Schneider 154 Electric References Variable speed drives Altivar 12 Drives with heatsink PFO80604F ATV12H018M2 Single phase supply voltage 100 120 V 50 60 Hz 4 0 18 0 256 5 0 6 1 1 4 2 1 18 ATV12H018F1 5 0 700 0 37 05 MA 93 1 1 1 2 4 3 6 29 ATV12H037F1 0 800 0 75 1 18 9 15 7 1 9 1 4 2 6 3 48 ATV12H075F1 1 300 5 Single phase supply voltage 200 240 V 50 60 Hz 4 6 5 0 18 0 25 34 2 8 0 7 1 1 4 2 1 18 ATV12H018M2 0 700 5 7 10 0 37 0 55 5 9 4 9 1 2 1 2 4 3 6 27 ATV12H037M2 0 700 7 10 0 55 0 75 8 6 7 1 6 1 3 5 5 3 34 ATV12H055M2 0 800 7 10 0 75 1 10 2 8 5 2 1 4 2 6 3 44 ATV12H075M2 0 800 ATV12H075M2 P 7 Ca 1 5 2 17 8 14 9 3 6 1 7 5 11 2 72 ATV12HU15M2 1 400 8 9 2 2 3 24 20 2 4 8 1 10 15 93 ATV12HU22M2 1 400 8 9 Three phase supply voltage 200 240 V 50 60 Hz 4 E 0 18 0 25 2 1 7 0 7 5 1 4 2 1 16 ATV12H018M3 5 0 700 A 0 37 055 3 6 3 1 2 5 2 4 3 6 24 ATV12H037M3 0 800 0 75 1 6 3 5 3 2 2 5 4 2 6 3 41 ATV12H075M3 0 800 1 5 2 11 1 9 3 3 9 5 19 11 2 73 ATV12HU15M3 1 200 2 2 3 149 125 5 5 10 15 85 ATV12HU22M3 1 200 3 19 15 9 6 6 5 12 2 18 3 94 ATV12HU30M3 2 000 4 5 238 19 9 83 5 16 7 25 128 ATV12HU40M3 2 000 Dimensions overall ATV12HU40M3 ATV12H018F1 H018M2 H018M3 72 x 189 5 x 102 2 72 x 143 x 102 2 ATV12H037F1 HO37M2 HO37M3 72x 189 5 x 121 2
12. It provides access to the same functions as the Human Machine interface The following characteristics complement those introduced in the selection guide on pages 6 to 9 Environmental conditions m IEC 60721 3 3 classes 3C3 and 3S2 Ambiant air temperature around the device in operation m For ATV12H018F 1 HO37F1 HO18M2 HO75M2 HO18M3 HO75M3 and ATV12Pecececee a From 10 C to 40 C without derating o Up to 60 C with the protective blanking cover removed and current derating of 2 per additional degree 7 m For ATV12H075F1 12HU15M2 HU22M2 12HU15M3 HU40M3 o From 10 C to 50 C without derating o Up to 60 C with the protective blanking cover removed and current derating of 2 per additional degree 7 1 See the derating curves in the User Manual available on our website at www schneider electric com Configuration Options Motor starters page 19 page 20 page 22 Schneider G Electric Presentation continuea Variable speed drives Altivar 12 Analog input Al1 m Voltage analog input 0 5 V internal power supply only or 0 10 V impedance 30 kQ m Analog current input X Y mA by programming X and Y from 0 20 mA impedance 250 Q Sampling time lt 10 ms Resolution 10 bits Accuracy 1 at 25 C Linearity 0 3 of the maximum scale value Factory setting Input configured as voltage type Analog output AO1 1 software configurable voltage or current analog output m Analog vo
13. TV 71EXA5 IP 55 with external water cooled system on request Variable speed drives Altivar 71 and Altivar 71 Plus Qu More technical information on www schneider electric com Schneider Electric Presentation Variable speed drives Altivar 12 The Altivar 12 drive is a frequency inverter for three phase 200 240 V asynchronous motors rated from 0 18 kW 0 25 HP to 4 kW 5 HP PF513412 The Altivar 12 s ease of installation based on the principle of Plug amp Play its compact size its integrated functions and its alternative base plate version make it particularly suitable for applications involving simple industrial machines and certain consumer machines By taking account of the constraints governing installation and use at the product design stage we have been able to offer a cost effective solution to manufacturers of compact simple machines OEMs and installers Examples of solutions provided m Drive factory configured for start up without the need for any adjustment m Multi Loader configuration tool for loading a configuration onto the drive without taking it out of its packaging m Labelled terminals to reduce wiring time drive identification on the front panel m Alternative delivery option of multiple units in a single special package 7 Like with the individually shipped drives itis possible to load a configuration into each drive without taking them out of the packaging Applications for simple industr
14. Variable speed drives Altivar 12 For 3 phase asynchronous motors from 0 18 to 4kW 0 25 to 5 HP Catalogue January 2013 Schneider Contents Variable speed drives Altivar 12 E BIOCHUfer 22 ae aes eevee ee a ee ip de de IP 20 or IP 21 variable speed drives for asynchronous and synchronous motors selection guide lt lt lt IP 54 or IP 55 variable speed drives for asynchronous and synchronous motors selection guide lt lt lt Variable speed drives Altivar 61 Plus and Altivar 71 Plus Seleccion QUO 5 2 u u 00 un nn dhe a ee aha Presentation of the Altivar 12 speed drives Presenta ea He nn ne ne anne doe a arn ABPICAIONS 1 nu a a a Oe a ee IA E a a FONCIONS a a q EEE is ee an ANOPBMIZEOONER o espian earar ENEA E EANN Complementary characteristics us 10H ee References Drives wih hedateink cou ricardo eee eh Pe See da ei Dives Ona base plale 2 sis we ies us bee dhe ee nenn POCE ONE oc et noo eae ee Gas peda ne ae ae a ee eee CONNOUIAUONIOONS aia hee nee Remote display terminals and associated cordsetS 00005 Additional EMCINPDUETISES asa 01000 00 0d ww ge cid ae nn MOIOFCHOKES s4 cd acewe reat to bs Seeded rn a bs a re Modbus serial lINKS 1224 020 264 4e4 te decir de DOCUMENTO vrs dere ra vee es PREIS IVIL ANUS variar cria ee aeg Motor starters PODICAIONG cui asadas ura eee vee Motor STAES inserciones o oe ee Salas ee S Combinations cec
15. a ea eae a ew ae iaa iia dad E 0 0 0 8 0 0 0 0 0 0 0 O O O 8 O O0 O O 0 MB Product reference index una nn annann Schneider Electric Designing technology that frees you from technical tasks Small Intuitive Reliable High performance With the Altivar 12 you get greater reliability and simplicity of operation and save even more time for all your applications e The smallest drive with integrated EMC for compact machines Collaborative design e Ever more intuitive and user friendly programming We surveyed our and mmens customers and users to deter e Can be configured in complete safety with the power off E even in Its packaging The result is A design that can withstand even the harshest AS environments e Quick and simple to set up e With no compromise on quality and components designed to last 10 years Make the most of your energy Combining efficiency with intelligence The Altivar 12 is particularly suitable for use in applications involving simple industrial machines or certain consumer machines Its compact size high performance and discreet appearance make it particularly attractive for use in the following sectors e The food industry ventilation of catering kitchens bagging machines bakers kneading machines greenhouses etc e Small handling applications car washes conveyors etc e The medical and health sector medical beds fitness machines e Machines with a si
16. ards for incremental resolver SinCos SinCos Hiperface EnDat or SSI encoders I O extension cards Controller Inside programmable card IEC 61800 5 1 IEC 61800 3 environments 1 and 2 categories C1 to C3 IEC 61000 4 2 4 3 4 4 4 5 4 6 4 11 C UL CSA DNV C Tick NOM GOST ATV 61W ATV 61E5 ATV 71W ATV 71E5 Altivar 61 variable speed drives Q gt More technical information on www schneider electric com Altivar 71 variable speed drives Schneider Electric Selection guide Variable speed drives Altivar 61 Plus and Altivar 71 Plus Integrated solutions a 90 630 125 900 90 800 125 900 630 2400 800 2500 90 630 90 630 630 1400 125 900 125 900 900 2000 90 630 630 1800 125 800 800 2500 110 800 800 2400 With enhanced protection With enhanced protection and integrated cooling circuit Ready to use Standard offer Modular with integrated options User definable on request 0 1 500 Hz Sensorless flux vector control Voltage frequency ratio 2 or 5 points Energy saving ratio Flux vector control without speed feedback 120 of the nominal motor torque for 60 seconds Modbus and CANopen Modbus TCP Modbus Uni Telway EtherNet IP DeviceNet PROFIBUS DP VO and V1 InterBus CC Link LonWorks METASYS N2 APOGEE FLN BACnet Controller Inside programmable card Multi pump cards IP 54 with separate air flows IP 23 compact vers
17. bile phone using a Bluetooth wireless connection Requires the Modbus Bluetooth adaptor VW3A8114 see page 17 It can also be used to back up configurations which can be imported or exported from a PC SoMove Mobile software can be downloaded from our website www schneider electric com 1 Available on our website www schneider electric com 2 Also includes other components for connecting compatible Schneider Electric devices 3 The SoMove Mobile software requires a basic mobile phone please consult our website www schneider electric com Accessories Configuration Options Motor starters page 18 page 19 page 20 page 22 Schneider Electric 19 PF080659B PFO80669A PF080672A References continuea Variable speed drives IE VW3A 1006 with cover open RUN FWD REV and STOP buttons accessible ATV12H075M2 with EMC kit Altivar 12 Remote display terminals additional EMC input filters Remote display terminals IP 54 degree of protection ATV12ececeecee VW3A1006 0 250 For fixing the Human Machine interface P 65 degree of protection ATV12eceeceee VW3A1007 0 275 on an enclosure door with IP 54 or IP 65 degree of protection Aremote fixing cordset VW3A1104Ree is also required Remote fixing cordsets Length 1m ATV12000000 VW3A1104R10 0 050 equipped with 2 RJ45 connectors Length 3m ATV12000000 VW3A1104R30 0 150 For connecting the VW3 A1 006 or VW3A1007 remote display terminal
18. connector m For SoMove 1 x 0 1 m cordset with 2 RJ 45 connectors 2 m For TwidoSuite 1 x 0 1 m cordset with 1 RJ 45 connector and 1 connector of mini DIN type USB Bluetooth adaptor for PC VW3A8115 Required for a PC which is not equipped with Bluetooth technology Connects to a USB port on the PC Range of 10 m class 2 Simple Loader Multi Loader configuration tools and associated cable Simple Loader tool ATV12000000 VW3A8120 For duplicating one drive configuration on another drive The drives must be powered up The tool is supplied with a cordset equipped with 2 RJ45 connectors 0 032 0 200 Multi Loader tool 1 ATV12000000 VW3A8121 For copying a configuration on a PC or drive and duplicating it on another drive The drives do not need to be powered up Supplied with the tool m 1 cordset equipped with 2 RJ45 connectors m 1 cordset equipped with a USB type A connector and a USB Mini B type connector m 1x2 GB SD memory card m 1female female RJ45 adaptor m 4 AA LR6 1 5 V batteries Cordset for Multi Loader tool 2 ATV12000000 in VW3A8126 For connecting the Multi Loader tool to the Altivar 12 drive in its its packaging packaging Equipped with a non locking RJ45 connector with special mechanical catch on the drive end and an RJ45 connector on the Multi Loader end SoMove Mobile software for mobile phone SoMove Mobile software allows you to edit drive parameters from ATV12e00000 1 3 a mo
19. e correctly see the specific manual for the Altivar 12 base plate version available on our website at www schneider electric com 7 This drive is delivered with a disconnectable category C1 EMC filter This drive complies with the IEC EN 61800 3 standard Environment 1 public network category C1 at 2 4 8 12 and 16 kHz for a shielded motor cable length inferior or equal to 5 m and category C2 from 2 to 12 kHz fora shielded motor cable length inferior or equal to 5m and at 2 4 and 16 kHz for a shielded motor cable length inferior or equal to 10 m 8 Available in lots of 14 add TQ at the end of the reference For example ATV12H018M2 becomes ATV12H018M2T0Q Drives Accessories Configuration Options Motor starters page 16 page 18 page 19 page 20 page 22 Schneider EZ References continued Variable speed drives Altivar 12 Accessories PF080670A Fixing plates for fixing on 35 mm wide LJ rail ATV12H018F 1 HO37F 1 VW3A9804 0 290 ATV12H018M2 HO75M2 ATV12H018M3 HO75M3 ATV12H075F1 VW3A9805 0 385 ATV12HU15M2 HU22M2 ATV12HU15M3 HU22M3 EMC conformity kits ATV12H018F1 HO37F1 VW3A9523 0 170 These provide a connection compliant with EMC standards ATV12H018M2 HO75M2 for further information please consult our website ATV12H018M3 HO75M3 www schneider electric com ATV12P037F 1 The kit consists of ATV12P037M2 P075M2 3 m The EMC plate ATV12P037M3 P075M3 g m Clamps m Fixing accessories ATV12H075F1 VW3
20. ial machines m Handling small conveyors etc m Packaging small labelling machines small bagging machines etc m Pumping applications suction pumps centrifugal pumps circulating pumps mono pump and multi pump stations etc m Machines equipped with a fan air or smoke extraction plastic film making machines ovens boilers washing machines etc ATV12 controlling an access barrier PF513418 Applications for consumer machines m Handling access barriers rotating advertising hoardings etc m Machines for health related areas medical beds hydromassage equipment running machines etc m Food and beverage industry machines mills kneading machines mixers etc Other types of application m Food and beverage industry battery farming greenhouses etc m Miscellaneous applications mobile machines and small appliances equipped with a power socket etc m Applications which traditionally use other solutions ATVT2 controlling a mixer o 2 speed motor DC motor mechanical drive etc O Single phase motor for pump and fan applications using mechanical control the Altivar 12 three phase motor solution adapts the power to the requirements of the driving application thus reducing energy consumption 1 Depending on the model see page 16 Drives Accessories Configuration Options Motor starters page 16 page 18 page 19 page 20 page 22 Schneider PF 513419 PF 513415 Presen
21. ion With integrated air cooled ATV 61ES5 ATV 61EXC2 circuit IP 54 compact version IP 23 ATV 61EXA2 ATV 61EXC5 IP 54 ATV 61EXA5 IP 54 with separate air flows With external water cooled ATV 61EXS5 system IP 55 on request ATV 61 Plus Variable speed drives Altivar 61 and Altivar 61 Plus More technical information on www schneider electric com 10 Schneider Electric 90 500 125 700 90 630 125 700 90 500 90 500 125 109 125 700 z 90 500 129 100 110 630 With enhanced protection Ready to use Standard offer Modular with integrated options User definable on request 0 1 500 Hz Flux vector control with or without sensor Voltage frequency ratio 2 or 5 points ENA System Vector control with or without speed feedback 220 of the nominal motor torque for 2 seconds 170 of the nominal motor torque for 60 seconds Modbus and CANopen Modbus TCP Modbus Uni Telway EtherNet IP DeviceNet PROFIBUS DP VO and V1 InterBus CC Link Controller Inside programmable card IP 54 with separate air flows ATV 71ES5 IP 23 compact version ATV 71EXC2 IP 54 compact version ATV 71EXC5 IP 54 with separate air flows ATV 71EXS5 ATV 71 Plus A 500 2000 550 2100 500 1300 550 1800 500 1500 700 2100 630 2000 With enhanced protection and integrated cooling circuit IP 23 with integrated air cooled circuit ATV 71EXA2 IP 54 with integrated air cooled circuit A
22. le C60N modular circuit breaker 5 For additional protection against direct contact with a three phase power supply and access to the DC bus terminals PA and PC the add on module must be type B with a sensitivity of 30 mA Drives Accessories Configuration Options Motor starters page 16 page 17 page 18 page 19 page 22 Electric Schneider Index ATV12H018F1 ATV12H018M2 ATV12H018M3 ATV12H037F1 ATV12H037M2 ATV12H037M3 ATV12H055M2 ATV12H075F1 ATV12H075M2 ATV12H075M3 ATV12HU15M2 ATV12HU15M3 ATV12HU22M2 ATV12HU22M3 ATV12HU30M3 ATV12HU40M3 ATV12P037F 1 ATV12P037M2 ATV12P037M3 ATV12P055M2 ATV12P075M2 ATV12P075M3 ATV12PU15M3 ATV12PU22M3 ATV12PU30M3 ATV12PU40M3 16 17 16 17 16 17 16 16 16 16 16 16 16 16 16 16 LU9GC3 TCSMCAM3M002P TCSWAAC13FB 19 VW3A1006 VW3A1007 VW3A1104R10 VW3A1104R30 VW3A4416 VW3A4417 VW3A4418 VW3A4419 VW3A4551 VW3A4552 VW3A4553 VW3A4554 VW3A8115 VW3A8120 VW3A8121 VW3A8126 24 VW3A8200 VW3A8306R VW3A8306R03 VW3A8306R10 VW3A8306R30 VW3A8306RC VW3A8306TF03 VW3A8306TF10 VW3A9317 VW3A9523 VW3A9524 VW3A9525 VW3A9804 VW3A9805 VZ3V1301 VZ3V1302 21 21 21 21 21 21 21 21 18 18 18 18 18 18 21 21 Product reference index Schneider Electric Schneider Electric 25 Schneider Electric Industries SAS Head Office 35 rue Joseph Monier F 92500 Rueil Malmaison France ART 059361 www
23. ltage output 0 10 V minimum load impedance 470 Q m Analog current output O to 20 mA maximum load impedance 800 Q Update time lt 10 ms Resolution 8 bits Accuracy 1 at 25 C Relay outputs R1A R1B R1C 1 protected relay output 1 N O contact and 1 N C contact with common point Response time 30 ms maximum Minimum switching capacity 5 mA for 24 V Maximum switching capacity m On resistive load cos y 1 and L R 0 ms 3 Aat 250 V or 4Aat 30 V m On inductive load cos 0 4 and L R 7 ms 2A at 250 V or 30 V Logic inputs LI1 L14 4 programmable logic inputs compatible with PLC level 1 standard IEC EN 61131 2 24 V Z internal power supply or 24 V external power supply min 18 V max 30 V Sampling time lt 20 ms Sampling time tolerance 1 ms Factory set with 2 wire control in transition mode for machine safety reasons m LI1 forward m LI2 L14 not assigned Multiple assignment makes it possible to configure several functions on one input for example LIT assigned to forward and preset speed 2 LI3 assigned to reverse and preset speed 3 Impedance 3 5 kQ Logic outputs LO LO One 24 V logic output assignable as positive logic Source or negative logic Sink open collector type compatible with level 1 PLC standard IEC EN 61131 2 Maximum voltage 30 V Linearity 1 Maximum current 10 mA 100 mA with external power supply Impedance 1 kQ Update time lt 20 ms
24. lti Loader IEC 61800 5 1 0 18 15 0 25 20 0 18 0 18 ESTE omor AN ET 13102920 3020 215 720 IP 21 Heatsink 0 1 500 Hz Standard voltage frequency Performance sensorless flux vector control Energy saving ratio 170 200 of the nominal motor torque 50 16 Modbus and CANopen CANopen Daisy Chain DeviceNet PROFIBUS DP Modbus TCP Fipio IP 54 or IP 65 remote terminal IP 54 remote graphic display terminal 75 1 100 0 75 30 1 40 0 75 75 1 100 0 5 200 Hz Sensorless flux vector control Voltage frequency ratio 2 points Energy saving ratio 120 ofthe nominal motor torque Modbus METASYS N2 APOGEE FLN BACnet LonWorks IP 54 or IP 65 remote graphic display terminal PCSoft for ATV 212 Multi Loader IEC 61800 3 environments 1 and 2 categories C1 to C3 cat C1 with option for ATV 212 C UL CSA C Tick NOM GOST C UL CSA DNV C Tick NOM GOST EN 55011 Group 1 classA and class B with option card CE UL CSA C Tick NOM ATV 12 ATV 312 ATV 212 Altivar 12 variable speed drives Altivar 312 variable speed drives 1 Heating Ventilation and Air Conditioning More technical information on www schneider electric com Schneider Electric Altivar 212 variable speed drives 0 37 800 0 5 900 Vera OU Zo 0 75 630 7 900 Zena oO 2 2 800 3 800 IP 20 Heatsink or wa
25. nal accessories and options External accessories and options can be used with Altivar 12 drives m EMC conformity kits plates for direct mounting on 35 mm 1 38 in Lr rail etc m Motor chokes additional EMC input filters etc Dialogue and configuration tools The 4 digit display 2 can be used to display states and faults access parameters and modify them via the navigation button 3 The RUN and STOP buttons 4 can be made accessible on the front panel by removing the blanking plate 5 from the door they must be configured in order to be active The Simple Loader tool enables one powered up drive s configuration to be duplicated on another powered up drive The Multi Loader tool enables configurations from a PC or drive to be copied and duplicated on another drive the drives do not need to be powered up The SoMove setup software can be used with the Altivar 12 drive for configuration adjustment debugging using the Oscilloscope function and maintenance just as it can for all other Schneider Electric variable speed drives and starters It can also be used to customize the integrated display terminal menus It can be used with a direct connection or a Bluetooth wireless connection EMOTE OISPDI ermi al The Altivar 12 drive can be connected to a remote display terminal available as an option This terminal can be mounted on an enclosure door with IP 54 or IP 65 degree of protection The maximum operating temperature is 50 C
26. ngle phase socket wood working machines surface polishing and cleaning machines swimming pool or irrigation pumps hydromassage bathtubs etc e New markets solar applications etc e Simple mechanical applications 2 speed motors DC motors mechanical drives etc ud 1 ME OPO a REED iz a A C PESE i A design focussed on integration e Upgrade your machines and make them more competitive with its advanced functions integrated PID multi speed the Altivar 12 increases your productivity e Communicate easily with all the other parts of your machine via the integrated universal Modbus serial link e Reduce the depth of your equipment the baseplate mounted version dissipates heat into the machine frame Economical e Design Save time by using the SoMove software Small The small format and advanced functions of the Altivar 12 mean workshop that it can easily replace any e Commissioning Quicker configuration with the existing drive in its category power off download function e Wiring and mounting Quicker and easier installation with integrated Modbus communication Choose peace of mind The Altivar 12 integrates as standard all the technologies that will make you forget it is there Its design and choice of components make the Altivar 12 an extremely efficient reliable and durable drive No compromise on quality e Ever higher performance for your motors assured by The factory settings
27. onment 1 public network category C2 from 2 to 12 kHz for a shielded motor cable length inferior or equal to 5 m and at 2 4 8 12 and 16 kHz for a shielded motor cable length inferior or equal to10 m 8 Complies with the IEC EN 61800 3 standard Environment 1 public network category C2 from 4 to 16 kHz for a shielded motor cable length inferior or equal to 5 m and at 2 4 and 16 kHz for a shielded motor cable length inferior or equal to10 m 9 Available in lots of 7 add TQ at the end of the reference ATV12HU22M2 becomes ATV12HU22M2TRQ 10 Available in lots of 14 add TQ at the end of the reference For example ATV12H018M2 becomes ATV12H018M2TQ Drives Accessories Configuration Options Motor starters page 18 page 19 page 20 page 22 Electric Schneider PF080623D References continued Variable speed drives Altivar 12 Drives on a base plate ATVERAS Single phase supply voltage 100 120 V 50 60 Hz 4 0 18 0 25 6 5 0 6 1 1 4 2 1 18 ATV12H018F1 5 0 700 11 4 9 3 1 1 1 2 4 3 6 29 ATV12P037F1 6 0 700 Single phase supply voltage 200 240 V 50 60 HZ 4 7 0 18 0 25 3 4 2 8 0 7 1 1 4 2 1 18 ATV12H018M2 5 8 0 700 5 9 4 9 1 2 1 2 4 3 6 27 ATV12P037M2 6 0 700 8 6 7 1 6 1 3 5 5 3 34 ATV12P055M2 6 0 700 10 2 8 5 2 1 4 2 6 3 44 ATV12P075M2 6 0 700 Three phase supply voltage 200 240 V 50 60 Hz 4 0 18 0 25 2 1 7 0 7 5 1 4 2 1 16 ATV12H01
28. plate version available on our website at www schneider electric com 3 TeSys motor circuit breakers GV2 MEee Thermal magnetic motor circuit breakers with pushbutton control GV2 Lee Magnetic motor circuit breakers with control by rotary knob 4 2 pole C60N modular circuit breaker 5 Can be integrated in devices connected to a power socket If the line current iss 16 A connection to a single phase power socket 10 16 A 250 Vx If the line current is gt 16 A connection to a single phase power socket conforming to standard IEC 60309 Drives Accessories Configuration Options Motor starters page 16 page 17 page 18 page 19 page 22 Electric Schneider Combinations for Variable speed drives customer assembly Altivar 12 Motor starters Three phase supply voltage continued 200 240 V M1 A1 Q1 KM1 Q1 a Three phase supply voltage 200 240 V 50 60 Hz C60N4P GV20000 0 18 025 ATV12H018M3 GV2ME07 1 6 25 gt 100 LC1K09 GV2L07 2 5 gt 100 4 pole C60N 6 10 0 37 0 55 ATV120e037M3 GV2ME08 25 4 gt 100 LC1K09 GV2L08 4 gt 100 oleo 4 pole C60N 6 10 KM1 l i Ob Wl AAA TeSys LC1eeee EY y i i a 0 75 1 ATV120075M3 GV2ME14 6 10 gt 100 LC1K09 if control circuit ION GV2L14 10 gt 100 al i ol 4 pole C60N 10 10 A1 1 5 2 ATV12eU15M3 GV2ME16 9 14 gt 100 LC1K12 ATV120000M3 GVL16 14 gt 100 4 pole C60N 16 10 2 2 3 ATV12eU22M3 GV2ME20 13 18 gt 100 LC1D18
29. re coated as standard and resistance to disturbed power supplies has been increased to withstand harsh environments Easy to identify e All the identification markings on the product are on a hinged door on the front panel e Easy identification of the connections Communicate intuitively with all your applications The Altivar 12 is immediately operational It is configured using the notched wheel or from the SoMove software workshop The Tile that is generated can be downloaded to the product even while it Is still In its packaging using the Multi Loader console You save commis sioning time so that you can spend more time doing your job Save time on commissioning e The drive can be configured before it is received by the distributor during storage by the storekeeper or during fitting before the electrical enclosure is powered up for the first time e No adjustment is required and there is a quick start guide for immediate setup e Work in the language of your choice with the SoMove software workshop that can be downloaded free of charge from www schneider electric com e Select the functions you need from the menu e Bluetooth option for PC for greater ease of use Save time on wiring e Easy access to all the wiring and adjustment functions on the front panel via a sealable hinged door e Integrated EMC filter in 240 V single phase versions e No need to remove the terminal cover to wire the power sec
30. tarters page 16 page 18 page 19 page 20 page 22 Electric Schneider PF080647A References continuea Variable speed drives Altivar 12 Motor chokes modbus serial links documentation replacement parts Motor chokes ATV12H018F 1 HO37F1 VW3A4551 Required ATV12H018M2 H055M2 m When connecting more than ATV12H018M3 HO37M3 2 motors in parallel ATV12P037F1 m When the motor cable length L ATV12P037M2 P055M2 including tap offs is ATV12P037M3 O 50 100 m for a shielded motor 10 ATV12H075F1 VW3A4552 3 700 cable 1 ATV12H075M2 HU15M2 ATV12VW3A455 o 100 200 m for an unshielded ATV12H075M3 HU15M3 Motor choke motor cable 1 ATV12P075M2 ATV12P075M3 PU15M3 16 ATV12HU22M2 VW3A4553 4 100 ATV12HU22M3 HU30M3 ATV12PU22M3 PU30M3 30 ATV12HU40M3 VW3A4554 6 150 ATV12PU40M3 Dimensions overall VW3A4551 100 x 135 x 60 VW3A4552 A4553 130 x 155 x 90 VW3A4554 155x 170x135 Connection via splitter box and RJ45 connectors D De att Modbus splitter box 1 LU9GC3 0 500 controller 2 10 RJ45 connectors and 1 screw terminal T 2 S D Cordsets for Modbus serial link 2 0 3 VW3A8306R03 0 025 2 equipped with 2 RJ45 connectors 1 VW3A8306R10 0 060 3 3 VW3A8306R30 0 130 Modbus T junction boxes 3 0 3 VW3A8306TF03 0 190 with integrated cable 1 VW3A8306TF10 0 210 E E m Line terminators R 1200 4 VW3A8306RC 0 010 4 5 C 1nf ATV 12 For RJ45 connector Example of Modbus diagram
31. tation continued energy saving Last fault occurred No faut Device state Ready Preset speeds with SoMove Drive with heatsink ATV12H075M2 ATV12H075M2 with door on front panel open Project Loaded Morir Drive on base plate ATV12P075M2 Variable speed drives Altivar 12 In addition to the functions usually available on this type of drive the Altivar 12 drive also features the following Application functions 7 m Switching between local control and control via the terminals m Motor control profiles standard performance and pump fan m Frequency skip m Preset speeds m PID regulator m Sramp U ramp ramp switching m Freewheel stop fast stop m Jog operation m Configuring the logic and analog I O m Underload and overload detection m Viewing the state of the logic inputs on the drive display m Configuring how the parameters are displayed m Error log etc Functions for pumping applications m Sleep wake up m PID functions m Protection functions o Protection against overloads and overcurrents in continuous operation pump jamming o Machine mechanical protection with control of operating direction Oo Protection of the installation by means of underload and overload detection The Altivar 12 range of variable speed drives extends across a range of motor power ratings from 0 18 kW 0 25 HP to 4 kW 5 HP on three types of power supply Two standard versions are available
32. ter cooled system 0 1 500 Hz for the entire range 0 1 599 Hz up to 37 kW 50 HP at 200 240 V and 380 480 V Sensorless flux vector control Voltage frequency ratio 2 or 5 points Energy saving ratio Vector control without speed feedback 120 of the nominal motor torque for 60 seconds 100 NOADNOv N O 4 Modbus and CANopen Modbus TCP Daisy Chain Modbus Uni Telway EtherNet IP DeviceNet PROFIBUS DP VO and V1 INTERBUs CC LINK LonWorks METASYS N2 APOGEE FLN BACnet I O extension cards Controller Inside programmable card multi pump cards encoder interface cards IP 54 or IP 65 remote graphic display terminal SoMove Simple Loader Multi Loader IEC 61800 5 1 0 37 630 0 5 700 OIN ao DN O S SV ao C AOS 100 0 75 500 1 700 laoo hZ u 1 5 630 2 700 Heatsink base plate or water cooled system 0 1 500 Hz for the entire range 0 1 599 Hz up to 37 kW 50 HP at 200 240 V and 380 480 V Flux vector control with or without sensor Voltage frequency ratio 2 or 5 points ENA System Vector control with or without speed feedback 220 of the nominal motor torque for 2 seconds 170 for 60 seconds gt 150 16 2 4 N 6 1 OF 2 KR w Modbus TCP Daisy Chain Modbus Uni Telway EtherNet IP DeviceNet PROFIBUS DP VO and V1 InterBus CC Link Interface cards for incremental resolver SinCos SinCos Hiperface EnDat or SSI encoders I O extension cards
33. the environment ROHS WEEE as well as those of European Directives to obtain the C mark 1 For the implementation of functions please consult the user manual on our website www schneider electric com Drives page 16 Accessories page 18 Configuration Options Motor starters page 19 page 20 page 22 Schneider 13 Electric Presentation continued ATV12H075M2 with door on front panel open Multi Loader configuration tool 009 oo Musas Remote terminal with cover closed Drives page 16 14 o Mv Remote terminal with cover open RUN FWD REV and STOP buttons accessible Accessories page 18 Variable speed drives Altivar 12 Electromagnetic compatibility EMC The integration of a level C1 EMC filter in ATV12eeeeM2 drives and the handling of EMC simplify installation and make it very inexpensive to bring the device into conformity to obtain the C mark This EMC filter can be disconnected via an internal switch 1 This filter is conform to the IEC61800 3 standard environnement 1 categories C1 and C2 depending on the model and on the motor cable length see pages 16 et 17 ATV12e0 0eeF 1 and ATV12e000M3 drives are designed without an EMC filter Filters are available as an option and can be installed by the customer to reduce the level of emissions see page 18 The ATV12eeeeM2 speed drives can also have an additionnal filter see page 19 Exter
34. tion e Only one screwdriver needed for wiring both the control and power sections e Less wiring due to the integrated Modbus communication Save time on programming e Anavigation button for easy menu access you can set the parameters of your applica tion with just a few clicks e A three level tree structure Reference Mode In local operation On Off buttons and for speed adjustment and display Monitoring Mode For displaying parameters Configuration Mode For configuring your applications and settings Use SoMove to customise your menus and save time during operation possible for up to 25 parameters Fast With the Multi Loa der console you can configure 10 drives in their packaging is less than 5 minutes with no power supply Versatile The Altivar 12 range is designed for 120 to 240 V power supplies For your productivity re quirements in the most varied applications see the complete Altivar range on our website www schneider electric com IP 20 or IP 21 variable speed drives for asynchronous and synchronous motors 0 18 4 0 25 5 Orica 072025 OA 2210253 0 18 4 0 25 5 IP 20 Heatsink or base plate 0 1 400 Hz Standard voltage frequency Performance sensorless flux vector control Pump fan Kn quadratic ratio 150 170 of the nominal motor torque 40 SN se se RES Ba 100 Modbus IP 54 or IP 65 remote terminal SoMove Simple Loader Mu
35. to the Altivar 12 drive Dimensions overall VW3A1006 50 x 70 x 22 7 For compliance with the requirements of standard IEC EN 61800 3 category C1 C2 or C3 in Environment 1 public network or Environment 2 industrial network depending on the drive rating ATV12H018F1 H037F1 5 20 20 VW3A4416 1 120 ATV12P037F1 ATV12H018M2 HO75M2 20 50 50 ATV12P037M2 P075M2 ATV12H075F1 5 20 20 VW3A4417 1 455 ATV12HU15M2 HU22M2 20 50 50 ATV12PU15M2 PU22M2 ATV12H018M3 HO75M3 20 20 VW3A4418 1 210 ATV12P037M3 PO75M3 ATV12HU15M3 HU22M3 5 20 20 VW3A4419 1 440 ATV12PU15M3 PU22M3 Dimensions overall VW3A4416 75 x 194 x 30 VW3A4417 117 x 184 x 40 VW3A4418 75 x 194 x 40 VW3A4419 117 x 190 x 40 1 The filter choice table gives the maximum lengths of the shielded cables between the motors and the drives These maximum lengths are given for indication because they depend on the motor properties and on the used cables In the case of parallel motors the total addition of the lengths must be taken into account VW3A9523 fixed on EMC 2 IEC 61800 3 standard EMC immunity and EMC conducted and radiated emissions filter VW3A4416 categories C1 et C2 public network category C3 industrial network For further information see the Conducted EMC emissions and Radiated EMC emissions characteristics on our website www schneider electric com Drives Accessories Configuration Options Motor s
36. y voltage 100 120 V 50 60 Hz 5 0 18 0 25 ATV12H018F1 GV2ME14 6 10 gt 100 LC1K09 Q1 Q1 C60N2P GV20000 Sal ae gt 10 2 pole C60N 10 10 0 37 0 5 ATV120037F1 GV2ME16 9 14 gt 100 LC1K12 GV2L16 14 gt 100 2 pole C60N 16 10 0 75 1 ATV12H075F1 GV2ME21 17 23 50 LC1D25 KM1 cd GV2L22 25 gt 50 TeSys LC1ee0ee i i 1 if control circuit MA 2 pole C60N 20 10 Single phase supply voltage 200 240 V 50 60 Hz 5 rer 0 18 0 25 ATV12H018M2 GV2ME08 2 5 4 gt 100 LC1K09 ATV120000F1 GV2L08 4 gt 100 ATV120000V 2 2 pole C60N 6 10 0 37 ATV120037M2 GV2ME14 6 10 gt 100 LC1K09 GV2L10 6 3 gt 100 2 pole C60N 10 10 0 55 ATV120055M2 GV2ME14 6 10 gt 100 LC1K09 M1 200 240 V three phase GV2L14 10 gt 100 asynchronous motor 2 pole C60N 10 10 0 75 7 ATV120075M2 GV2ME16 9 14 gt 100 LC1K12 Motor starter with single phase power supply GVL16 14 gt 100 2 pole C60N 16 10 1 5 2 ATV12HU15M2 GV2ME21 17 23 50 LC1D18 GV2L20 18 gt 100 2 pole C60N 20 10 2 2 3 ATV12HU22M2 GV2ME32 24 32 50 LC1D25 GV2L22 25 50 2 pole C60N 32 10 1 For a complete list of references for TeSys contactors please refer to the Motor starter solutions Control and protection components and Motor starters up to 150 A catalogues or visit www schneider electric com 2 Motor power indicated for combination with an ATV12Heeeee drive with the same rating For combination with an ATV12Peeeee drive refer to the specific manual for the Altivar 12 base
Download Pdf Manuals
Related Search