Honeywell SmartLine EU Meter Users manual, 34-ST-25-19
Contents
1. Engineering Units Meter The Engineering Units Meter EU is described briefly here only in the context of RMA 3000 application and installation For detailed information such as digital display features installation set up and operation refer to 34 ST 25 18 Engineering Unit Meter User s Guide Function The Engineering Unit Meter is an LCD indicator that provides a digital display of a transmitter s output PV when connected in a 4 to 20 mA analog loop The meter is compatible with Honeywell Smartline Transmitters operating in analog mode and with other non Honeywell transmitters operating in a 4 to 20 mA current loop Description The EU meter is designed to provide a simple indication of a transmitter s output value A multi segmented LCD display is encased in a circular black plastic frame for local installation to the transmitter A printed circuit assembly PW A is mounted behind the display and contains the electronics and wire connections for the meter The EU meter is powered from the transmitter loop current A momentary contact toggle switch is mounted on the PW A and is used for setting up and verifying the display indication 12 RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 Installation in Hazardous Locations For installation in hazardous locations the RMA 3000 must be configured and installed as detailed in the appropriate Honeywell certified engineering drawing s which conform to practices specified2. 30V Il 100mA 1 2W AMBIENT LIMITS 40 C TO 85 C ENCLOSURE IP 66 67 INSTALL PER 34 ST 25 19 034 50031953 001188 ASSEMBLED IN INDIA PUNE 411013 INDIA Nameplate 50031954 001 nA Zone 2 is mounted on the enclosure The following is a representation of this nameplate m Honeywell RMA 3000 REMOTE METER ASSEMBLY MODEL O CUST ID MFG DATE Ex nA IIC 40 TO 85 Ex tD A22 P6X T95 C Ta 85 C x II 3 GD ZONE 2 SUPPLY Ui 42V 23mA A C 3 AMBIENT LIMITS 40 TO 85 C ENCLOSURE IP 66 67 INSTALL PER 34 ST 25 19 K 50031954 001 155 B ASSEMBLED IN INDIA PUNE 411013 INDIA 28 RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 Special conditions for safe use Intrinsic Safety X The RMA 3000 Models RMA300 SM ME amp EU Remote Meter Assemblies are intrinsically safe apparatus that can be installed in potentially explosive atmospheres The power terminals must be connected only to a certified associated intrinsically safe apparatus The electrical parameters U I and P of the associated apparatus connected to the power terminals must not exceed the following values Ui x 30V Ili 100mA Pi lt 1 2 W Ambient temperature 20 to 60 40 C to 85 C Temperature classification T5 up to Ta lt 60 C T4 up to Ta lt 85 C Specific Parameters for Flameproof and
3. i EN 60079 26 2004Special Requirements for Construction Test and Marking of Electrical Apparatus of Equipment Group Il Category 1 G Notified EC Type Examination Certificates Production Quality Assurance Notification Bodies CIE Groupe Bureau Veritas 0081 KEMA Quality B V 0344 33 Avenue du G n ral Leclerc Utrechtseweg 310 92260 Fontenay aux Roses 6812 AR Arnhem France The Netherlands Certificate Protection Description Models RMA300ME RMA300SM RMA300EU Remote Meter Assemblies LCIE 08 ATEX 6045 X II 1 G Ex ia IIC Models RMA300DM RMA300SM RMA300ME amp LCIE 08 ATEX 6044 X 2 G Ex a IIC T5 RMA300EU Remote Meter Assemblies rerit Honeywell Automation India Ltd 56 amp 57 Hadapsar Ind Estate ocation Pune 411013 India The authorized signatory to this declaration on behalf of the manufacturer and the Responsible Person is identified below Honeywell Automation India Ltd 56 amp 57 Hadapsar Industrail Estate Bhavesh Varia Pune 411013 India Product Safety and Approval Engineer Issue Date 30 April 2008 30 RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 Appendix B Hazardous Location Wiring North America Class I Division 1 and Group Zone 1 Requirements Wiring shall be in accordance with the applicable portions of the National Electrical Code ANSI NFPA 70 NEC for the United States the Canadian Electrical Code CSA C22 1 C
4. 11 CSA HART Release 7 RMA 3000 Remote Meter Assemblies User Manual May 2011 23 Table 5 Wiring Overview DM ST 3000 Not Approved for HART DM Release 300 Transmitter With Lightning Protection Option Drawings Without Lightning Protection Option Drawings 51204241 5 FM 51204241 9 FM 51204242 5 CSA 51204242 9 CSA 24 RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 Installation in Non Hazardous Locations When installed in ordinary non hazardous locations wiring shall comply with National Electrical Code NEC or with local electrical code requirements Multiple Remote Meters The Honeywell certified engineering drawings of wiring configurations that have been approved by FM CSA and ATEX include only configurations that include a single meter SM DM ME or EU with a single Honeywell ST 3000 Pressure Transmitter However the Honeywell remote meter housing provides a convenient means of connecting multiple meters to a single transmitter in non hazardous locations Series Connected Meters As mentioned under Meter Types Options near the beginning of this manual the SM and the ME are current oriented series connected devices Multiple meters any combination of SM and ME may be connected to a given transmitter provided that the following condition is met Voltage pwr supply gt Minimum Terminal Voltage transmitter Number of SMs 2 3 volts Resistance Total Loop 22 mA
5. 3033 South Korea Honeywell Korea Co Ltd Phone 822 799 6114 Fax 822 792 9015 Thailand Honeywell Systems Thailand Ltd Phone 662 693 3099 FAX 662 693 3089 Taiwan R O C Honeywell Taiwan Ltd Phone 886 2 2245 1000 FAX 886 2 2245 3243 SE Asia Countries see Honeywell Pte Ltd Singapore for Philippines Pakistan Cambodia Guam Laos Myanmar Vietnam East Timor SE Asia Countries see Honeywell Automation India Ltd for Bangladesh Nepal Sri Lanka EUROPE Austria Honeywell Austria GmbH Phone 43 316 400123 FAX 43 316 40017 Belgium Honeywell SA NV Phone 32 0 2728 24 07 FAX 32 0 2728 22 45 Bulgaria Honeywell EOOD Phone 359 2 40 20 900 FAX 359 2 40 20 990 Czech Republic Honeywell spol s r o Phone 420 242 442 232 FAX 420 242 442 131 Denmark Honeywell A S Phone 45 39 55 55 55 FAX 45 39 55 55 58 Finland Honeywell OY Phone 358 0 20752 2753 FAX 358 0 20752 2751 France Honeywell SA Phone 33 0 1 60198075 FAX 33 0 1 60198201 Germany Honeywell AG Phone 49 69 8064 299 FAX 49 69 806497336 Hungary Honeywell Kft Phone 36 1 451 4300 FAX 36 1 451 4343 Italy Honeywell S p A Phone 390292146307 FAX 39 0292146377 The Netherlands Honeywell B V Phone 31 0 20 5656200 FAX 31 0 20 5656210 Norway Honeywell A S Phone 45 39 55 55 55 Poland Honeywell Sp zo o Phone 48 22 606
6. B STA o LII T LOOP OR METER FAUI XMTR TUS T FAULT LAST KNOWN VALUE Figure 1 Overview of RMA Configuration Release 7 RMA 3000 Remote Meter Assemblies User Manual 9 May 2011 That is the explosion proof housing may be located atthe end of a wiring run for the transmitter loop or between the transmitter and the receiver devices This manual includes several sets of Honeywell certified engineering drawings that specify RMA 3000 configurations and conditions that are approved for use in hazardous environments by various approval agencies FM CSA and LCIE ATEX Each of these drawings shows a configuration similar to that shown in Figure 1 that is a single meter connected remote from a single transmitter In some selected cases such as operation in non hazardous locations it is possible to connect more than one meter to a given transmitter In these cases the additional meter s may be placed either at the end of a wiring run or at any location between the transmitter and other elements of the Remote Meter Assemblies configuration The number of meters that may be incorporated depends on the circuit configuration and on electrical characteristics of associated equipment For more information regarding the use of multiple remote meters with a single transmitter refer to the descriptions under the heading Multiple Remote Meters Meter Types Options Remote Meter Assemblie
7. Meter CSA Supersedes Sheet 1 of 51204242 Lightning Protection Option Sheet 2 RMA 300 SM Sheet 3 RMA 300 ME Sheet 4 RMA 300 ME Analog Meter Sheet 5 RMA 300 DM Non Lightning Protection Option Sheet 6 RMA 300 SM Sheet 7 RMA 300 ME Sheet 8 RMA 300 ME Analog Meter Sheet 9 RMA 300 DM For intrinsically safe application ATEX Lightning Protection Option Sheet 1 Intrinsically Safe ATEX Sheet 2 RMA 300 SM Sheet 3 RMA 300 ME Sheet 4 RMA 300 ME Analog Meter Non Lightning Protection Option Sheet 5 RMA 300 SM Sheet 6 RMA 300 ME Sheet 7 RMA 300 ME Analog Meter RMA 3000 Remote Meter Assemblies User Manual The certified and approved engineering drawings available for specific applications in hazardous locations are listed in Table 1 Some of the drawings include details of integral mounting of the meter in transmitters in addition to that for remote meter mounting 51204241 50029789 51204242 51204243 Release 7 May 2011 Application Document Description Drawing Number ST 3000 HART Series 100 and 900 For intrinsically safe application FM 51205784 Transmitters Lightning Protection Option Note these drawings are also included Sheet 1 Intrinsically Safe FM in Sheet 2 RMA 300 ME Analog Meter 34 ST 25 17 Sheet 3 RMA 300 SM Release 300 with HART Sheet 4 RMA 300 ME Communications Option User Manual Non Light
8. N3HAA C3MO TIOH 38 LS IN SNIMAO NOLEV TTV LSNI S H3HCLLOVATNVIN OI31VIDOSSV 03141932 OS 3l NOLLVOO T SDIOUH V ZVH NOSIA SS 12 NI C3TTVLSNI 38 AVA Sn vdvddv 0319120553 031511939 WSO 38 LSNN So vvddv O 31Vvi20SsV WAOSddV VS2 L YOHLIM O31LLIWH3d 51 9NIMYU SIHL O L NOISIA3H ON LHyd 3002 TV2I4L93T3 NVIOVNYO JHL 39NYOHOOOV NI 38 LSNA NOLLWTIVLSNI A 08 NVH1 31VH3N39 HO LON LSNW Sniivsvddv I31vI20SSsV OL I3193NNOO LNAWdINDA 10H1NO2 ONV TO 3 18v 2 03151 q q w rh co cn lt e 015 02 I 35 20A XBW NOLLVITTVA3 ALLLN3 SNOLLONYLSNI S H3 LOVAnNVIN HUM 39NYOHOOOV NI GSTIVLSNI 38 LSNW S3 va 0351 38 AVN Sarda 0340930 ATLEN3 HO AHLINYA Yd VSO L OGL 0 3IN DOE NA 0 0 ING DOEVINH 0 Jur z WS 00EvINH 0 n3 o0eviN 6 9 8 SILON GNNOYD T3IHS 9 I3dOMW AL3JVS 2ISNIHINI A CL vul Gzz Aver ps XPWA i i 3LON Sealaiiwvevd ALLLN3 6 ILON a aiHs JOMLNOD 9 ILON H31H3ANO2 S nlvHvddv g31vi2O0ssVv 3LON A lddfis INS DOEVINH 1H 00 VINH T SNOILdO amp 43l3lN 3 LOINd 000 VIA E E LV ELE AIO Ill 12 H 3 d9 IL AIO 1 19 S3OI 3U dOO 1 TIV JOT A46 E el 222 8 Vd9 LAIG 110 S3OI 3d dOO1 TIY JO D IqE39 lt ED DISNIHINI 35 3dVS ATIVOISNIHLNI 606 gt 25 EIX A F CF gt 20
9. Non Sparking Installation Power supply to field wiring terminals and Ucc lt 42 V Output Signal 4 20 mA Special conditions for safe use Flameproof and Non Sparking Installation Ambient operating temperature 40 to 85 C Release 7 May 2011 RMA 3000 Remote Meter Assemblies User Manual 29 51453800 Revision A DECLARATION OF CONFORMITY x ATEX C 0344 We declare under our sole responsibility that the following products RMA 3000 Remote Meter Assemblies to which this declaration relates are in conformity with the protection requirements of Council Directive 94 9 EC ATEX Directive on the approximation of the laws of the Member States concerning equipment and protective systems intended for use in potentially explosive atmospheres and 89 336 EEC EMC Directive as amended by 92 31 EEC 93 68 EEC and 2004 108 EC on the approximation of the laws of the Member States relating to Electromagnetic Compatibility The models covered by this Declaration and evidence of conformity with the ATEX Directive are shown below Conformity to the ATEX Directive is in accordance with the following European standards EN 60079 0 2004 Electrical Apparatus for Potentially Explosive Atmospheres General Requirements EN 60079 1 2004 Electrical Apparatus for Potentially Explosive Atmospheres Flameproof Enclosure d EN 60079 11 2007Electrical Apparatus for Potentially Explosive Atmospheres Part11 Intrinsic Safety
10. Option 21 Table 3 Wiring Overview SM ST 3000 Transmitter with HART Option 22 Table 4 Wiring Overview ME ST 3000 Transmitter with or without HART Option 23 Table 5 Wiring Overview DM ST 3000 Not Approved for HART 24 Mutual EM COE atiy uyu t a uve rain ud tata ee 34 Table 7 Canadian Standards Association CSA Certification ener ens 36 Table DER uiuos ito P a 38 MES CE x CIE OS O05 m 39 Table TO Sout Amei SAES NAN A IA u cb pi RI US DE 30 Figures Figure 1 Overview or RMA Configuration ER RA Ep ERE Ete pieta dero pl M e d LETS VES 9 2 T iehliehts ot Meter Reames REPE ta TE u MTM 10 Fisure y Examples ot Typical Conduit FUNES s s u uQ aq edt et eese et Or ptos EE 13 Figure Example Of Sealed Cable Gland m a dtt dites ied tae die gece lout 13 Assembly dor CE MiK eto Reti noe dm Meter vede oben e a TE 14 Figure o RMA 5000 TIntrirsto Safety Parattle fetis 15 Figure 7 Stylized Sample
11. Revision Notes About This Document About This Document The following list provides notes concerning all revisions of this document Doc ID Rel ID Date Notes 34 ST 25 19 Rev O 11 28 First issue of document 34 ST 25 19 Rev 1 6 25 04 Revised Appendix A ATEX Directive 94 9 EC 34 ST 25 19 Rev 2 8 19 05 Revised Appendix A D 34 ST 25 19 Rev 3 9 1 05 Revised Appendix C 34 ST 25 19 Rev 4 5 08 Remove STT150 References added EU Meter and Updated Appendices 34 ST 25 19 Rev 5 12 08 IECEx certification added 34 ST 25 19 Rev 6 10 09 CSA updates table 1 34 ST 25 19 Rev 7 May 2011 SAEx and ATEX approvals added Contacts World Wide Web The following lists Honeywell s World Wide Web sites that will be of interest to our customers Honeywell Organization WWW Address URL Corporate http www honeywell com ps hfs Honeywell Process Solutions International Telephone htto hosweb honeywell com Cultures en US http www honeywell com ps http www honeywell com business global asp Contact us by telephone at the numbers listed below By Telephone Additional Help By E Mail Problem Resolution Release 7 May 2011 Honeywell Solution Support Center Phone 1 800 423 9883 U S only Outside the U S call 1 602 313 6510 You may also seek additional help by contacting the Honeywell distributor who supplied your RMA 3000 transmitter You can also e mail your technical questions or comments about this product to Honeywell Solutio
12. of Certified Engineering DrawIng n nnnsnsnssnssse a sssssssssssssssssssssa 17 Figures Lesend Tor Wiring Diostan OVODVIe W spese uu sa OR bcd Mi nda Td ta o usq 20 vi RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 CE Conformity Europe Notice for Remote Meter Assemblies Abou Release 7 May 2011 RMA t Conformity and Special Conditions This product is in conformity with the protection requirements of 89 336 EEC the EMC Directive and of 94 9 EC the Explosive Atmospheres ATEX Directive Conformity of this product with any other Mark Directive s shall not be assumed Deviation from the installation conditions specified in this manual and the following special conditions may invalidate this product s conformity with the EMC Directive Shielded twisted pair cable such as Belden 9318 must be used for all signal power wiring The shield must be connected to ground at only one end of the cable Connect it to the power supply and the meter sides of the wiring leave the shield insulated at the transmitter side of the wiring n ATTENTION The emission limits of EN 50081 2 are designed to provide reasonable protection against harmful interference when this equipment is operated in an industrial environment Operation of this equipment in a residential area may cause harmful interference This equipment generates uses and can radiate r
13. which can be delivered by the associated apparatus considering faults and applicable factors In addition the maximum unprotected capacitance Ci and inductance Li of the intrinsically safe apparatus including interconnecting wiring must be less than or equal to the capacitance Ca and inductance La which can be safely connected to the associated apparatus If these criteria are met then the combination may be connected and remain intrinsically safe Both FMRC and CSA entity parameters are defined in Tables 6 and 7 Table 6 Factory Mutual FM Certification Description Explosion proof for Class I Division 1 Groups A B C amp D Dust Ignition proof for Class 11 Division 1 Groups E F amp G Suitable for Class 111 Division 1 Conduit seals required within 18 of enclosure Group A only Intrinsically Safe for use in Class I Division 1 Groups A B C D Class ll Division 1 Groups E F amp G Class lll Division 1 T4 at 40 T3A at 93 maximum ambient when connected in accordance with Honeywell drawing 50034080 Non incendive for use in Class l Division 2 Groups A B C amp D Suitable for Classes II amp 111 Division 2 Groups F amp G T4 at 93 C maximum ambient hazardous locations 42 Vdc max Environmental Indoor and outdoor hazardous locations NEMA 4X With no integral indicator or with integral Smart Meter option SM Li 150 uH With Analog Meter option ME Install in accordanc
14. 0900 FAX 48 22 6060901 Portugal Honeywell Portugal Lda Phone 351 21 424 5000 FAX 351 21 424 50 99 Romania Honeywell Bucharest Phone 40 0 21 2316437 FAX 40 0 21 2316439 Russian Federation RF Honeywell Field Solutions Kievskaya str 7 Moscow 121059 Russia Phone 7 495 796 98 60 Fax 7 495 797 99 64 Slovak Republic Honeywell s r o Phone 421 2 58247 410 FAX 421 2 58247 415 Spain Honeywell S A Phone 34 0 91313 61 00 FAX 34 0 91313 61 30 Sweden Honeywell AB Phone 46 8 775 55 00 FAX 46 8 775 56 00 Switzerland Honeywell AG Phone 41 18552448 FAX 41 1 855 24 45 Turkey Honeywell Turkey A S Phone 90 216 578 71 00 FAX 90 216 575 66 35 Ukraine Honeywell Tel 380 44 201 44 74 Fax 380 44 201 44 75 United Kingdom Honeywell Control Systems Ltd Phone 44 0 1344 655251 FAX 44 0 1344 655554 MIDDLE EAST Abu Dhabi U AE Middle East Headquarters Honeywell Middle East Ltd Phone 971 2 4041246 FAX 971 2 4432536 Sultanate of Oman Honeywell amp Co Oman LLC Phone 968 24 701153 Ext 33 FAX 968 24 787351 Saudia Arabia Honeywell Turki Arabia Ltd Jubail Office Phone 966 3 341 0140 Fax 966 3 341 0216 Honeywell ATCO Dammam Office Phone 0096638304584 Fax 0096638338059 Kuwait Honeywell Kuwait KSC Phone 965 242 1327 to 30 Fax 965 242 8315 And Phone 965 326 2934 1821F ax 965 326 1714 Specifications are
15. 9NYH2 9NIH33NION3 IllowAo9uoH 19 99 dl XF Oc 6 LV F1 0 9 2 9 dO L AIO T 19 JjOOHd NOISO IdX3 d3LlLIWNSNYVL a SS320ud i E i SniVvadvddv GALVIDOSSV ONIIM 1did 000 HLIM 3181lLvdlWO2 SH3ldivHvd VSO JISNIHANI 31IHP71035S 34VS ATIVOISNIHANI 1 9 93131999 YSI YSJ v ONISN 543814 ONY 15 0 LSNIYOv S3IH1N3 318v2 TWIS ISN LON SI LINGNOD Tv13W GIOI 343HM SNOILVTIVI SNI III 11559710 03 J3Wro0 viNH INC 00 VIA JSA SNJ 2 68267005 31l30v2 T6BFEO00 OO4 335 S IVAOSHddV 3597139 cl XNYSONVO NON 3N9IS30 153 LNSWS9V1d 3 1 SND 3HnSSV S INVS09 31334102 1N3NWdI03 133193NNO0293 30 INVAY NOISO 1dX3 Q 3f10STH 7 IN3WASSEEUH JAV SNOOHYZVH NON 38 OL NMONM SI V3HV JHL HO 440 I3HOLIMS N3H8 SVH H3MOd JHL SS3 TNI LNaMWdl 603 LOANNODSIO LON OG dvzvH NOISO dX3 9NINSVM SONINHVM ONIMOTIOJ JHL 3AH3S80 SHSIMMVE LNOHLIM SNOLLVTTV LSNI Z NOISIAIC NI ONIAVH 1 NOLLOSdSNI 77207 OL J318v1d322v SV 3002 TV2IH12313 NVIQVNYO JHL 3d NONOJ TVLIW GIOTH JO NOLLO3NNOO 304 SNOISIAOHd HUM 3408S019N3 318V1In v TIVM IHL H NOYHL NI CHTIVISNI N3HM Q 2 8 V Sd 1089 NOISIAIQ 1 SSV12 NI Sd3lddva LOOHLIM NOLEVTTVISNI H03 318V1Ins 0 ANO ONG ATdd NS 3HL LY T30NnO89 GT3IHS ALINDININI ONG 404 CSON3ININOO3H SI 3HIM lt WHO NVH1 553739 LSnIN HLVd ONNOYD JHL 30 39NVISISdH 1N3Mdi 103 SIHL ONITTV LSNI
16. A SHJLJWYHYd ALILNA 8I66G00 024 B50 v 8 A3 31v 9 NOISIA3H SIHL HLIEN ON TENOLUENHSTENI TISNLLSNCOH 6007 LHS HOO ui ima SNOGHVZVH Lg cd Ru pM C NOILVOOT1SnOGNVZVH NON 37 RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 Table 8 ATEX LCIE Certification Intrinsically Safe LCIE O2ATEX 6178X we Ww l 1GExiallC T5 Ta 40 to 60 eX Flameproof LCIE O2ATEX6177X fe Il 2 G Ex d IIC T6 Ta 40 to 65 C Ex Il 2 D Ex tD A21 IP6X T95 C at Ta 85 C orT80 C at Ta 65 C Sparking HON 02 202 I 3 G Ex nA IIC 6 40 lt Tas 65 Ex Il 3 D Ex tD A22 IP6X T95 C at Ta 85 C orT80 C at Ta 65 C Intrinsically Safe LCIE O2ATEX 6178X Il 1 G Ex ia T5 Ta 40 to 60 Flameproof LCIE O2ATEX6177X Ex Il 2 G Ex d IIC T6 Ta 40 to 65 C ve I 2 D Ex tD A21 IP6X T95 C at Ta 85 C orT80 C at Ta 65 C Non Sparking HON 02 202 Il 3 G Ex nA IIC T6 40 lt lt 65 CX II 3 D Ex tD A22 IP6X T95 C at Ta 85 C orT80 C at Ta 65 C The user must determine the type of protection required for installation the equipment The user shall then check the box a adjacent to the type of protection used on the equipment certification nameplate Once a type of protection has been checked on the nameplate the equipment shall not then be reinstalled using any of the other certificati
17. D3 SIHL ONITIV LENI N3HM G3NGO TIO4 38 LSNN ONIMIVO NOLLV TIV LSNI S YSUNLOWANNVN SNLYHYddY G31VID2OSSV amp NOSAC SSV T2 NI 38 AVN 03131920557 SdAOddV 38 LSNA I3LVIDOSSV IAOMHddVv LD IOHLIM O31LLIWH3d SI SNIMYHU SHL OL NOISIA3H ON VdJN 3009 MAAL TH TVNOLLVN JHL HUM 39NYOHO2OV NI 38 LENAN NOLLVTTv 1SNI A 062 NVHL SHOW 3L VH3N39 LON LSNA SALYA Ydd IHIVIDOSSV OL GS LOSNNOD INSWNdINOA TOHINO2 LLYN V ONISN SH38lH ONY 15 0 LSNIVOY S3lHIN3 TT8V2 138 3SN LON 51 LINGNOD MLIN III SNOLLVTIVISNI III 11 SSY TO HOS gSA SNJ 8 68 6 005 T T1302 AXXXXD0 023 335 IVAOHddV 3531395 cL SDOQHVZVH NON 38 OL NMONM SI IHL HO 440 Q3H21IMS N338 SVH H3MOd JHL SSAINN LNIANE 193NNO9SIO LON OG dH vZvH NOISO 1dX3 ONINHVM r oen cn qaanHHu 32 OS dl NOLUIV2OO 1 SnOOHVZVH INOZ SSv19 ed sf u NILLIS NV TO T18V2 031511 ed 07 02 10 35 20A XeulA NOLLVITTgAS ALLNI SNOLLONYLSNI 6 3LON admins Na 00 VIN SNOILdO 3L3W 3 LOIN38 000 VINA L AIG 119 z am a jG G Li a Tu Perr scene SSH ovanNvMW 39NvOHOOOV NI GSTTVLSNI 38 LSNA 8 038 38 AVN SHSM C3lHLEH39 ALLN HO G3AOHddV Wd L SILON 6 8 8 SILON GONNOYD T3IHS 9 AL3JVS 2OISNIHLNI 3LON INAWdINOA TOHLNOJ 9 3LON PO H31H3ANO2 maywa SNLYHY ddi aai
18. EC for Canada NEC Fixed wiring methods for Class I Division 1 locations specifies threaded rigid metal conduit threaded steel intermediate metal conduit type MI mineral insulated type MC metal clad or type ITC intermediate tray cable listed for use in Class I Division 1 locations with termination fittings approved for the location Division 1 Group C amp D Sealing and drainage shall be provided in accordance with Article 501 5 a c d and f Wiring methods for Class I Zone 1 locations allows all wiring methods permitted for Class I Division 1 locations above Wiring methods for Class 1 Zone 1 Class I Division 1 per Appendix 718 106 locations specifies threaded rigid metal conduit or cables approved for hazardous locations with associated cable glands explosion proof seal fittings that comply with Rule 18 100 and Appendix B18 100 When installed with rigid metal conduit explosion proof seal fittings approved for the location shall be installed in each conduit run within 3 8 cm 1 5 in of the Sensor Assembly explosion proof enclosure When installed with cable explosion proof seal fittings shall be installed within 3 5 cm 1 5 in of the Sensor Assembly explosion proof flameproof enclosure or explosion proof flameproof direct entry cable glands approved for the location shall be used Class I Division 2 and Group Zone 2 Requirements NEC Fixed wiring methods for Class I Division 2 lo
19. Enhanced mode e ST 3000 Smart Pressure Transmitter STT 3000 Smart Temperature Transmitter Electrical Characteristics The DM is a voltage oriented device that is connected in parallel with the transmitter via the Red positive wire and Yellow negative wire The DM is an AC coupled device that senses the magnitude of the voltage pulses sent by the transmitter Each DM draws 0 5 mA of current Several DM meters can be connected in parallel with the transmitter provided that the sum of the current loads imposed by each DM in the loop does not exceed the capacity of the power supply Release 7 RMA 3000 Remote Meter Assemblies User Manual 11 May 2011 ME Analog Meter Function The ME is an analog device that functions as an output indicator for any transmitter that operates in the 4 20 mA current mode Application The ME can be used as a Remote Meter Assembly component with any one of the following Smartline Transmitters operating in the analog 4 to 20 mA mode Electrical Characteristics The ME is an electromechanical device of the D Arsonval type That is the current passing through a coil in the meter is used to deflect a needle to indicate the magnitude of the current where a current of 4 20 mA represents 0 to 100 The ME can be used in combination with the SM in the same loop provided that the formula presented under the SM description above in electrical characteristics for multiple meters is obeyed EU
20. Honeywell RMA 3000 Remote Meter Assemblies User Manual Doc No 34 ST 25 19 Release 7 Last Revision Date May 2011 Honeywell Process Solutions Notices and Trademarks Copyright 2011 by Honeywell International Inc Release 7 May 2011 HART is a trademark of the Hart Communication Foundation Warranty Remedy Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship Contact your local sales office for warranty information If warranted goods are returned to Honeywell during the period of coverage Honeywell will repair or replace without charge those items it finds defective The foregoing is Buyer s sole remedy and is in lieu of all other warranties expressed or implied including those of merchantability and fitness for a particular purpose Specifications may change without notice The information we supply is believed to be accurate and reliable as of this printing However we assume no responsibility for its use While we provide application assistance personally through our literature and the Honeywell web site it is up to the customer to determine the suitability of the product in the application Honeywell Process Solutions 1860 West Rose Garden Lane Phoenix Arizona 850277 Honeywell is a U S registered trademark of Honeywell Other brand or product names are trademarks of their respective owners li RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011
21. NOTE Total loop resistance must Include wiring and cabling as well as for associated apparatus such as barrier devices and control equipment such as Field Terminal Assembly FTA and FTA cabling Parallel Connected Meters Release 7 May 2011 As mentioned under Meter Types Options near the beginning of this manual the Digital Enhanced meter DM is a voltage oriented device that is connected in parallel to a transmitter Each DM draws 0 5 mA of current Several DM meters can be connected in parallel with the transmitter via the yellow wire negative and red positive wires provided that the sum of the current loads imposed by each DM in the loop does not exceed the capacity of the power supply RMA 3000 Remote Meter Assemblies User Manual 25 Appendix A ATEX Certificate Purpose and Content This Manual includes information required under the ATEX Directive regarding of this Appendix T The appearance and meaning of each certification mark CE Mark that appears on the label s affixed to the product 2 Instructions for installation and use of the product Details regarding certification marks that appear in labeling for this product are given in this addendum Attention The publication cited above and the functioning and construction except for labeling of the devices described therein are essentially unchanged The purpose of this addendum is to provide details of the purpose and appearance of the labe
22. adio frequency energy and may cause interference to radio and television reception when the equipment is used closer than 30 meters 98 feet to the antenna e In special cases when highly susceptible apparatus is used in close proximity the user may have to employ additional mitigating measures to further reduce the electromagnetic emissions of this equipment RMA 3000 Remote Meter Assemblies User Manual vii RMA 3000 Description Function and Design The Honeywell RMA 3000 Remote Meter Assemblies provide various means of remote mounting a meter that is associated with a Honeywell Smartline Transmitter or a compatible non Honeywell transmitter The RMA 3000 includes a remote meter housing that can be used in hazardous environments or in ordinary environments When used in hazardous environments the remote housing must be configured as a flameproof explosion proof housing in which all points of entrance and exit for wiring are protected and sealed via rigid metal conduit or suitable cable gland fittings Four meter styles are available and with a few exceptions any of these may be connected in either of two basic physical wiring configurations as indicated in Figure 1 viii RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 Power Supply Transmitter Flameproof Control Equipment Explosion proof Barrier Converter Housing vv YV v v 0 100 IDID OM OM oy UTI NO DATA LAS WN VALUE L
23. by various approval agencies Installation requirements vary somewhat among approval agencies Wiring Port Seals at Remote Housing When used in hazardous environments the remote housing may be configured as a flameproof explosion proof housing in which all points of entrance and exit for wiring are protected and sealed via rigid metal conduit or suitable cable gland fittings Examples of metal conduit fittings are shown in Figure 3 and an example of a sealed cable gland is shown in Figure 4 Conduit Fireproof Explosion proof Vertical Seal Expanded Fil Seal w Drain Horizontal Hawke ICG 623 EEx d EEx e 72 NPT Sealing Non Armored Figure 4 Example of Sealed Cable Gland Release 7 RMA 3000 Remote Meter Assemblies User Manual 13 May 201 1 SM Meter Assembly The SM Meter assembly includes an integral filter plate and an associated mounting plate in the flameproof explosion proof housing as shown in Figure 5 To install an SM 3000 Smart Meter Remove the cap from the housing Rotate the meter assembly counter clockwise until it can be pulled from the mounting plate in the housing Connect field wiring to the terminal block in the housing Align four stand offs on the bottom of the meter assembly with holes in the mounting plate insert bottom of stand offs in the holes and turn the meter assembly clockwise to lock it in place Ensure that the meter is oriented properly for viewing through the cap window Lub
24. cations specifies threaded rigid metal conduit threaded steel intermediate metal conduit type MI mineral insulated type MC metal clad type ITC intermediate tray cable or type TC tray cable listed for use in Class I Division 2 locations with cable with termination fittings approved for the location Division 2 Group C amp D Sealing and drainage shall not be required to be explosion proof and shall be provided in accordance with Article 501 5 b c d and f Wiring methods for Class I Zone 2 locations allows all wiring methods permitted for Class I Division 2 locations above CEC Wiring methods for Class I Zone 2 Class I Division 2 per Appendix B18 156 locations specifies threaded rigid metal conduit or cables approved for hazardous locations with associated cable glands that comply with Rule 18 100 or type TC cable installed in cable tray in accordance with Rule 12 2204 or type ACWU cable with associated cable glands that comply with the requirements of Rule 18 150 or type ACIC control and instrument cables with interlocking metallic armor and a continuous jacket with associated cable glands that comply with the requirements of Rule 18 150 Cable Systems for Division 1 Zone 1 and Division 2 Zone 2 Marine Shipboard Cable Installations on Offshore Oil Rigs and Drilling Platforms Cable and fittings for threaded connection to equipment in hazardous locations shall conform to the installation and use provis
25. e with Honeywell drawing 50034080 RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 d Iv 2s NOISN3MIO Y TON 080v 006 GI31DN SS3INn 39N YH3 TO 2e 6 IV 9L 0 2 8 d9 I AIG 119 STFAOYHddY O3zrioHln JjOOtd NOISO IdX4 3g LSNW 023 843030 3NVHOONNZONONI _ I1N3M 200 NOLLY2131L832 051 n 0 12 JN O0 VIAH o n D 5 WO DOEVIWH 4Ue9 19 WS 0OEVIWH 0 r1 0 5 00 vIWH M L xewd Wu GZ A V F XEUIA SddldWveva ALLLN3 SS320Hd JW 00 VINH IWCFO0EVINH INS O0EVINH snlVavddyY 31190557 ONY ONIIM 07131 000 VW HUM d THLEV dINOO sudlLa3Wvavd 34vs ATIVOISNISINI Oe 6 LY PLL AIO TIE TO 9 H3 dO L AIG ITO Oe 5 1 V FL Oll 0 INOZ 1 10 0 9 2 8 V dO JJ4VS A TIVOISNIS LNI SONINHYM ONIMOTIOS JHL 3 3580 6 1 SNOLLYTIVLSNI Z INOZ Z NOISIAIG NI NOLLOIGSIHRP NIAVH NOLLOSASNI T907 JHL OL 31814399V SV O vdHN 3000 TvOI8193 TH TWNOLLWN JHL Yad LINGNOD TLAN GOTH JO NOLE 3NNOO SNOISIAOMd HUM 3150 1ON3 318V1I0S v 40 TIVM IHL HONOYHL NI G3TIV1SNI N3HM Z INOZ ISSV T2 0 9 2 SdNOY9 NOISIAI 1 SSV12 NI SH3IMHVB LNOHLIM NOLLWTIVISNI HO4 318v Ins 0 ANO ATddns IHL 1v CONDOMNO GTIIHS ALINDINITOWS G3ON3WAOO3M 51 SHIM G3 THS WHO SS31 38 15nIN HLYd ONNOYO IHL 4O 39Nv1SIS3H 79 99 di XP 3dAL ENSE SENE 1N3MdIni
26. ifications of the housing or as intrinsically safe and of the installation practices used therewith When installed as intrinsically safe external wiring shall be in accordance with ordinary location requirements that is NEC or CEC or local codes For information regarding integral installation in Honeywell Smart Transmitters refer to the following publications ST 3000 Smart Pressure Transmitters 34 ST 25 14B 34 ST 25 17 34 ST 25 33 ST 3000 Smart Transmitter Release 300 and SFC Smart Field Communicator Model STS 103 User s Manual ST 3000 Smart Transmitter Release 300 with HART Communications Option User Manual ST 3000 Smart Transmitter Release 300 and SFC Smart Field Communicator Model STS 103 User s Manual RMA 3000 Remote Meter Assemblies User Manual 15 16 ST 3000 Smart Temperature Transmitters EN1I 6190_Feb11 ENI1I 6190 Mar10 Legacy ENII 6162 ENII 6196 STT 3000 Series STT250 Temperature Transmitter Models STT25H STT25D STT25M STT25T STT25S Operator Manual STT 3000 Series STT250 Temperature Transmitter Models STT25H STT25D STT25M STT25T Operator Manual STT 3000 Smart Temperature Transmitter Models STT350 Operator Manual STT 3000 Smart Temperature Transmitter Models STT35F Operator Manual RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 Approvals for Specific Configurations Certified Drawings Release 7 May 2011 Several specific configurat
27. ion DEKRA Quality B V Arnhem the Netherlands 0344 e Complete model number See the Model Selection Guide 34 ST 16 46 The serial number is 10 digits long The first digit is the STT Type R U or S The second digit is the year code 0 9 The third and fourth digits are the week code in hexadecimal The remaining six digits are the serial number Marking and Inscriptions Nameplate 50031950 001 is mounted on the enclosure The following is a representation of this nameplate E ic d Omm Buc pant H e UR dq nay uie x Honeywell REMOTE METER ASSEMBLY MODEL CUST ID MFG DATE mom LCIE 08 ATEX 6044X Ex d IIC 6 Ta 20 TO 65 5 40 TO 85 C Ex tD A21 IPEX T95 C Ta 85 C TB0 C Ta 65 SUPPLY Veo 42 Voce OUTPUT 4 20 mA II 2 G WARNING DO NOT WHEN ENERGIZED AFTER CX DE ENERGIZING DELAY 1 MINUTE BEFORE OPENING N AMBIENT LIMITS 20 C TO 65 C 40 C TO 485 C 0344 ENCLOSURE 66 67 INSTALL PER 34 57 25 19 x 50031950001 155 ASSEMBLED IN INDIA PUNE 411013 INDIA ju u X s Release 7 RMA 3000 Remote Meter Assemblies User Manual 27 May 2011 Nameplate 50031953 001 ia is mounted on the enclosure The following is a representation of this nameplate MODEL LCIE 08 ATEX 6045X Ex la G T4 Ta 40 TO 85 C T5 Ta 20 TO 60 C Ex tD 20 IP6X T95 C 85 C T80 C 65 pll 1 GD Ul
28. ions of Remote Meter Assemblies have been approved for use in hazardous locations by various approval agencies Each of these specific configurations has been documented by Honeywell in controlled Engineering Drawings that are certified by Honeywell and approved by the appropriate body FM CSA and ATEX Copies of the certified drawings are included in this publication at the end of this section For descriptive purposes a stylized generic sample of these drawings in given in Figure 7 below As indicated in Figure 7 each drawing or set of drawings shows alternate wiring methods for placing the meter between the Power Supply Control Equipment Approved Associated Apparatus and the Transmitter or for placing the meter at the end of the wiring loop In many cases wiring methods are similar for several configurations approved by various notified bodies However notes that specify entity parameters and special conditions are unique for each approval agency and for each configuration covered by that approving body It is very important to select the correct drawing s and to comply with all notes regarding special conditions in the drawings When installed in ordinary non hazardous locations wiring shall comply with National Electrical Code NEC or with local electrical code requirements WARNING For use of the RMA in hazardous locations It is the user s responsibility to select the appropriate engineering drawings and to ensure that all co
29. ions of Sub part 111 60 of the United States Coast Guard Electrical Engineering Regulations Subchapter J Title 46 Code of Federal Regulations Part 110 to 113 inclusive as applied by the authority having jurisdiction for the installation Release 7 RMA 3000 Remote Meter Assemblies User Manual 31 May 2011 European Union and Countries That Follow ATEX IECEx Practices Cables for Fixed Apparatus shall be thermoplastic sheathed cables thermosetting sheathed cables elastomeric sheathed cables or mineral insulated metal sheathed cables for fixed wiring Cables for fixed wiring shall have flame propagation characteristics that enable them to withstand the tests according to EN 60332 1 1 and EN 60332 1 2 Cable entry systems cable glands shall comply with all of the requirements referred to in the appropriate apparatus standards EN 60079 0 and EN 60079 1 the cable entry device is appropriate to the type of cable employed and maintains the respective method of protection The cable entry system shall comply with one of the following a Cable terminal compartment with cable entry device and a particular type of cable in compliance with EN 60079 1 b Thermoplastic thermosetting or elastomeric cable that is substantially compact and circular has extruded bedding and the fillers if any are non hygroscopic may utilize flameproof cable entry devices incorporating a compression seal c Mineral insulated cable with or without plastic ou
30. l 41 Sales and Service For application assistance current specifications pricing or name of the nearest Authorized Distributor contact one of the offices below Asia Pacific Global Technical Support Field Instruments Phone 65 6580 3156 Fax 65 6445 3033 Australia Honeywell Limited Phone 61 7 3846 1255 FAX 61 7 3840 6481 Toll Free 1300 36 39 36 Toll Free Fax 1300 36 04 70 China Beijing Honeywell China Inc Phone 86 10 8458 3280 Fax 86 10 8458 4650 China Shanghai Honeywell China Inc Phone 86 21 5257 4568 Fax 86 21 6237 2826 China Chengdu Honeywell China Inc Phone 86 28 6613 5078 Fax 86 28 8678 7061 China PRC Xi an Honeywell China Ltd Xi an Phone 86 29 8833 7490 Fax 86 29 8833 7489 China Shenzhen Honeywell China Inc Phone 86 755 2518 1226 Fax 86 755 2518 1221 Indonesia PT Honeywell Indonesia Phone 62 21 535 8833 FAX 62 21 5367 1008 Honeywell Automation India Ltd Honeywell Ltd Phone 91 6603 9400 Fax 91 6603 9600 Japan Honeywell Inc Phone 81 3 6730 7197 Fax 81 3 6730 7228 Malaysia Honeywell Engineering Sdn Bhd Phone 603 7958 4788 Fax 603 7958 8922 New Zealand Honeywell Limited Phone 64 9 623 5050 Fax 64 9 623 5060 Toll Free 0800 202 088 Singapore Honeywell Pte Ltd Phone 65 6580 3278 Fax 65 6445
31. ls attached to each device under ATEX Directive 94 9 EC Attention Before installing the equipment in a potentially explosive atmosphere please read the information provided in this Manual which supports the ATEX certifications for this product CE Conformity The Honeywell RMA 3000 Models RMA300 DM SM ME and EU Remote Meter Assemblies are in conformity with the protection requirements of the following European Council Directives 94 9 EC the Explosive Atmospheres ATEX Directive and 2004 108 EC the EMC Directive Conformity of this product with any other CE Mark Directive s shall not be assumed Deviation from the installation procedures and conditions specified in the Operator s Manual may invalidate this product s conformity with the ATEX and EMC Directives Conformity of this product with any other CE Mark Directive s shall not be assumed 26 RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 Marking Honeywell s RMA 3000 Models RMA300 DM SM ME amp EU Remote Meter ATEX Directive Assemblies with the following nameplates attached has been certified to comply with Directive 94 9 EC of the European Parliament and the Council as published in the Official Journal of the European Communities No L 100 1 on 19 April 1994 The following information is provided as part of the labeling of the transmitter e Name and Address of the manufacturer Honeywell Phoenix AZ 85053 USA e Notified Body identificat
32. n Support Center e mail ace honeywell com If itis determined that a hardware problem exists a replacement transmitter or part will be shipped with instructions for returning the defective unit Please do not return your transmitter without authorization from Honeywell s Solution Support Center or until the replacement has been received RMA 3000 Remote Meter Assemblies User Manual iii Symbol Definitions The following table lists those symbols used in this document to denote certain conditions Symbol Definition This CAUTION symbol on the equipment refers the user to the Product Manual for additional information This symbol appears next to required information in the manual WARNING PERSONAL INJURY Risk of electrical shock This symbol warns the user of a potential shock hazard where HAZARDOUS LIVE voltages greater than 30 Vrms 42 4 Vpeak or 60 VDC may be accessible Failure to comply with these instructions could result in death or serious injury gt gt ATTENTION Electrostatic Discharge ESD hazards Observe precautions for da handling electrostatic sensitive devices Protective Earth PE terminal Provided for connection of the protective earth green or green yellow supply system conductor 8 IF p lt Functional earth terminal Used for non safety purposes such as noise immunity improvement NOTE This connection shall be bonded to protective earth at the source of supply in accordance with national l
33. nditions specified in those drawings are adhered to in every respect ST 3000 Pressure Transmitter POWER SUPPLY ENTITY NOTE APPROVED ASSOCIATED APARATLIS CONTROL ARR CONVERTER EQUIPMENT NOTES MOTE Explosion proof Housing RED POWER SUPPLY ENTITY NOTE APPROVED ASSOCIATED CONTROL IBAR 2 B 88 EQUIPMENT NOTES MOTE Figure 7 Stylized Sample of Certified Engineering Drawing RMA 3000 Remote Meter Assemblies User Manual 17 List of Certified Engineering Drawings Wiring Diagrams 18 ST 3000 Release 300 Series 100 and 900 Transmitters Note these drawings are also included in 34 ST 25 14 ST 3000 Smart Transmitter Release 300 and SFC Smart Field Communicator Model STS103 User Manual 34 ST 33 39 ST 3000 Smart Transmitter Release 300 and SFC Smart Field Communicator Model STS103 Installation Guide Table 1 Certified Engineering Drawings Wiring Diagrams Application Document Description Drawing Number For intrinsically safe application FM Lightning Protection Option Sheet 1 Intrinsically Safe FM Sheet 2 RMA 300 SM Sheet 3 RMA 300 ME Sheet 4 RMA 300 ME Analog Meter Sheet 5 RMA 300 DM Non Lightning Protection Option Sheet 6 RMA 300 SM Sheet 7 RMA 300 ME Sheet 8 RMA 300 ME Analog Meter Sheet 9 RMA 300 DM For intrinsically safe application CSA Interconnection Diagram RMA3000 Remote
34. ning Protection Option Sheet 5 RMA 300 ME Analog Meter Sheet 6 RMA 300 SM Sheet 7 RMA 300 ME For intrinsically safe application CSA Interconnection Diagram RMA3000 50029789 Remote Meter CSA Supersedes Sheet 1 of 51450806 Lightning Protection Option 51450806 Sheet 2 Communicator Sheet 3 RMA 300 ME Analog Meter Sheet 4 RMA 300 SM Sheet 5 RMA 300 SM Sheet 6 RMA 300 ME Sheet 7 RMA 300 ME Non Lightning Proof Option Sheet 8 RMA 300 ME Analog Meter Sheet 9 RMA 300 SM Sheet 10 RMA 300 ME Sheet 11 RMA 300 ME Release 7 RMA 3000 Remote Meter Assemblies User Manual 19 May 2011 Wiring Drawings Overview The wiring drawings included in the following tables are included in this manual to provide a quick reference for interpreting the information given in the Honeywell certified engineering drawings referenced in the tables These simplified drawings are intended for use along with certified engineering drawings to indicate the similarities differences among various wiring configurations WARNING These simplified drawings are not intended as a substitute for the certified drawings The certified drawings must be used as the sole source for wiring installation instructions A legend for use with the wiring diagrams overview is given in Figure 8 In this illustration the power source shown at left in a dashed outline represents all of the following com
35. ocal electrical code requirements Earth Ground Functional earth connection NOTE This connection shall be bonded to Protective earth at the source of supply in accordance with national and local electrical code requirements Chassis Ground Identifies a connection to the chassis or frame of the equipment shall be bonded to Protective Earth at the source of supply in accordance with national and local electrical code requirements 17 RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 Contents CE Conformity Europe Notice for Remote Meter Assemblies RMA vil About Conformity and Special CondltlOris u uuu u u a oua tu vade vii RMA O000 DOSCIHDIU OP c eda nondam 8 Funcion and MEETS 8 Meter TY DCS SOPUN T kanas 10 Installation in Hazardous Locations nnne nnn nnne nnns 13 Wiring Port Seals at Remote Housing nnns nan nnn nn nnns 13 SM Meter Assembly ES La tule bt csi estt 14 Specific Parameters of the Mode of Protection Intrinsic 14 Abprovals CertllCalloliS ss uuu L iha a obire o pida 15 Approvals for Specific Configurati
36. on types Certification and Conformity Details ATEX Intrinsic Safety Parameters Ui 30 V li 100 mA Pi 1 2 W Ci 4 2 nF Ri 0 Li 0 With no integral indicator or with integral Smart Meter option SM Li 150 uH With Analog Meter option ME D Install in accordance with Honeywell drawing 51204243 38 RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 Table 9 IECEx LCIE 08 0034 Intrinsically Safe Ex ia IIC T4 Ta 40 C to 85 C T5 Ta 20 C to 60 C Flameproof Ex d IIC T6 Ta 20 C to 65 C T5 Ta 40 C to 85 C IECEx Intrinsic Safety Entity Parameters Ui 30V li 100 mA Pi 1 2 W Ci 4 2 nF Ri 0 Li 0 With no integral indicator or with integral Smart Meter option SM Li 150 uH With Analog Meter option ME Table 10 South Africa SAEx S 09 341X Intrinsically Safe Ex ia IIC T4 Ta 40 C to 85 C T5 Ta 20 C to 60 C Flameproof Ex d IIC T6 Ta 20 C to 65 C T5 Ta 40 C to 85 SAEx Intrinsic Safety Entity Parameters Ui 30V li 100 mA Pi 1 2 W Ci 4 2 nF Ri 0 Li 0 With no integral indicator or with integral Smart Meter option SM 150 With Analog Meter option ME Release 7 RMA 3000 Remote Meter Assemblies User Manual 39 May 2011 40 RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 Release 7 May 2011 RMA 3000 Remote Meter Assemblies User Manua
37. ons Certified Drawings 17 List of Certified Engineering Drawings Wiring Diagrams 18 Wiring Drawings 20 Installation in Non Hazardous 25 Multiple Remote Meters uuu 25 Appendix A ATJEX CeortifieKdgleu uuu uuu uu su ama ERE cum datae uris dau 26 Marking and InseriptionS RH 27 DECLARATION OF CONFORMITY R a oU eu ie 30 Appendix B Hazardous Location Wiring 31 NOMDAMSUC Ssni a a a a Sauna 31 Cable Systems for Division 1 Zone 1 and Division 2 Zone 2 31 Appendix C Hazardous Locations Certification 33 ENUM cR rnc ter 34 Certification and Conformity Details a 38 Release 7 RMA 3000 Remote Meter Assemblies User Manual May 2011 Tables Table Engimeerme Drawings Wiring Diagrams ias ipeo uri d ea e asi i el nuusan a ta 18 Table 2 Wiring Overview SM ST 3000 Transmitter without HART
38. ponents shown in the certified drawings e Power Supply e Control Equipment e Approved Associated Apparatus Transmitter Remote Meter Housing LEGEND se Black dots on schematic represent Connectors T inside Remote Meter Housing Figure 8 Legend for Wiring Diagrams Overview 20 RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 Table 2 Wiring Overview SM ST 3000 Transmitter without HART Option SM for Release 300 Transmitter without HART Option Without Lightning Protection Option Drawings With Lightning Protection Option Drawings 51204241 6 FM 51204242 6 CSA 51204243 5 ATEX 51204241 2 FM 51204242 2 CSA 51204243 2 ATEX Release 7 RMA 3000 Remote Meter Assemblies User Manual 21 May 2011 Table 3 Wiring Overview SM ST 3000 Transmitter with HART Option SM with HART Option With Lightning Protection Option Drawings Without Lightning Protection Option Drawings 51205784 3 FM 51205784 6 FM 5145080644 5 CSA 51450806 9 CSA 22 RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 Table 4 Wiring Overview ME ST 3000 Transmitter with or without HART Option Without Lightning Protection Option Drawings With Lightning Protection Option Drawings 51204241 3 FM 51204241 7 FM 51204242 3 CSA 51204242 7 CSA 51204243 3 ATEX 51204243 6 ATEX 51205784 4 FM HART 51205784 7 FM HART 51450805 6 7 CSA HART 51450806 10
39. ricate the threads and the o ring on the meter housing with a silicone grease such as Dow 33 or equivalent Replace the cap Meter with Filter Assembly Cap with Figure 5 SM Meter Assembly for CE Mark Specific Parameters of the Mode of Protection Intrinsic Safety The specific parameters for the mode of protection Intrinsic Safety for the Analog Meter ME and for the Smart meter SM are listed in Appendix C under the specific agency A diagram of the field connections in from the flameproof explosion proof housing is given in Figure 6 14 RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 Analog Assembly ME IS Parameters Ui lt 30 V li lt 100 mA Pi x 1 2 W Ci lt 0 Li lt 150 uH Ri 0 4 20 mA Analog 30751118 TAB N rE cO 6 LL D QQ QQ QQ Smart Meter FL Ci lt 6 nF 51308619 002 Smart Meter Assembly SM with Filters IS Parameters Ui lt 30 V li lt 100 mA Pi lt 1 2 W Filter Plate Assy Ci x 18 nF 51204200 001 Li 0 negligible Approvals Certifications Release 7 May 2011 Figure 6 RMA 3000 Intrinsic Safety Parameters Each of the meter selections SM DM ME EV itself carries no approvals or certifications for use in hazardous areas or for RFI etc However when it is properly installed in the flameproof explosion proof housing or when installed as intrinsically safe the meter is covered by the approvals and cert
40. s provide for four meter types The features of each are highlighted in Figure 2 and are described after the figure Lingen P Lu i e Pep OO DILE nm LIT ZLOUTMIEN URN GPP A MUT BEANIE Figure 2 Highlights of Meter Features 10 RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 SM Smart Meter The Smart Meter SM is described briefly here in a context of RMA installation only For detailed information on digital enhanced operating mode display features operation and calibration refer to 34 ST 25 08D SM 3000 Smart Meter User s Manual Function The Smart Meter SM is a digital device that functions as an output and status indicator for a compatible Honeywell Smartline Transmitter or just as an output indicator for a non Honeywell transmitter operating in a 4 to 20 mA current loop It can operate in the analog mode 4 20 mA or can operate in the Honeywell proprietary Digital Enhanced DE mode Application The SM can be used as a Remote Meter Assemblies component with any one of the following Smartline Transmitters e ST 3000 Smart Pressure Transmitter e STT 3000 Smart Temperature Transmitter As indicated in the illustration the SM is similar in appearance to the DM That is they both have a multi segment fan style bargraph that indicates from 096 to 10046 and both include status indicators However the SM can be easily distinguished from the DM in that
41. subject to change without notice AFRICA Mediterranean amp African Distributors Honeywell SpA Phone 39 02 250 10 604 FAX 39 02 250 10 659 South Africa Republic of and sub saharan Honeywell Southern Africa Honeywell S A Pty Ltd Phone 27 11 6958000 FAX 27 118051504 NORTH AMERICA Canada Honeywell LTD Phone 1 800 737 3360 FAX 1 800 565 4130 USA Honeywell Process Solutions Phone 1 800 423 9883 Or 1 800 343 0228 Email ask ssc honeywell com SOUTH AMERICA Argentina Honeywell S A 1 C Phone 54 11 4383 3637 FAX 54 11 4325 6470 Brazil Honeywell do Brasil amp Cia Phone 55 11 7266 1900 FAX 55 11 7266 1905 Chile Honeywell Chile S A Phone 56 2 233 0688 FAX 56 2 231 6679 Mexico Honeywell S A de C V Phone 52 55 5259 1966 FAX 52 55 5570 2985 Puerto Rico Honeywell Inc Phone 809 792 7075 FAX 809 792 0053 Trinidad Honeywell Inc Phone 868 624 3964 FAX 868 624 3969 Venezuela Honeywell CA Phone 58 2 238 0211 FAX 58 2 238 3391 Honeywell Honeywell Process Solutions 1860 West Rose Garden Lane Phoenix Arizona 85027 www honeywell com ps hfs 34 ST 25 19 Rev 7 May 2011 02011 Honeywell International Inc
42. ter covering with appropriate flameproof entry device d Flameproof sealing device e g a stopper box or sealing chamber specified in the apparatus documentation or having component approval and employing cable entry devices appropriate to the cables used The sealing devices such as stopper boxes or sealing chambers shall incorporate compound or other appropriate seals which permit stopping around individual cores Sealing devices shall be fitted at the point of entry of the cables to the apparatus e Flameproof cable entry devices incorporating compound filled seals or other equivalent sealing arrangements f Other means which maintain the integrity of the flameproof enclosure 32 RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 Appendix C Hazardous Locations Certification Copies of the certificates can be found at http hpsweb honeywell com Cultures en US Products Approvals documents htm Release 7 RMA 3000 Remote Meter Assemblies User Manual May 2011 33 Entity Concept 34 Under entity requirements the concept allows interconnection of intrinsically safe apparatus to associated apparatus not specifically examined in such combination The criteria for interconnection is that the voltage Vmax and current Imax which intrinsically safe apparatus can receive and remain intrinsically safe considering faults must be equal to or greater than the voltage Voc or Vt and current Isc or It levels
43. the SM has e 7 segment bargraph compared to 25 for the DM e more status indicators than the DM e three wire connections Red Blue and Yellow to other components whereas the DM has two wire connections Red and Yellow e The SM has aconfiguration button on the periphery of the case at lower left Electrical Characteristics The SM is a current oriented device that is connected in series with the transmitter via the Yellow and Blue wires The Red wire carries virtually no current its purpose is to provide a digital communication signal voltage for the meter In non hazardous locations the RMA 3000 can include more than one SM and can be used in combination with the ME analog meter For more information refer to the paragraphs under the heading Multiple Remote Meters DM Digital Enhanced Meter The Digital Enhanced Meter DM is described briefly here only in the context of RMA 3000 application and installation For detailed information such as DE operating mode display features operation and calibration refer to 34 ST 25 07A DE 3000 Smart Meter User s Manual Function The Digital Enhanced Meter DM functions as an output and status indicator for a compatible Honeywell Smartline Transmitter operating in the DE mode only that is it cannot be used in the analog mode as can the SM Application The DM can be used as an RMA 3000 component with any one of the following Smartline Transmitters operating in the DE Digital
44. vi2ossv 3LON Adds S32I dd dOO1 40 3Iqg2 lt E S3ol add dOO JO D lt EJ Gec gt 38 F F gt 30A SHadldvHvdad A LILNd SnlOCHVZVH NON j Jj j G i i 35 RMA 3000 Remote Meter Assemblies User Manual Release 7 May 201 1 Table 7 Canadian Standards Association CSA Certification Explosion Proof for Class I Division 1 Groups B C amp D Dust Ignition Proof for Class II Division 1 Groups E F amp G Class Ill Division 1 Conduit seals not required 42 Vdc max Intrinsically Safe for Class 1 Groups A B C amp D Class II Groups E F amp G Class Ill Divisions 1 T4 at 40 T3A at 93 C maximum ambient Install per Honeywell drawing 50029789 Suitable for Class Il amp 111 Division 2 Groups A B C D E F amp G hazardous locations T4 at 93 42 Vdc max Environmental Indoor and outdoor hazardous locations Encl 4X CSA Certified Barriers Class I II III Division 1 and 2 Groups D Install in accordance with Honeywell drawing 50029789 RMA 3000 Remote Meter Assemblies User Manual Release 7 May 2011 L dO L LHS NOISN3MICG HY INONY aasn INON d Tv 2s CALON SSSINN SONVHSTOL 8 VSO UYSLSW SLOWSY 0008 WW yx SAN NOLLO3NNOOM3INI rd ZOZO wax 4 OOHO zoezo NMvud SNIJ33NISN3 S vAOuddV Q3zldOHln v 3g LSNA 8023 544040 3
Download Pdf Manuals
Related Search