GETTING STARTED? EASY.
Contents
1. Lo bu N F D N A CE2. Make sure that the drain filter is not clogged Clean the filter if neces sary Refer to Care and cleaning Make sure that the connection of the drain hose is correct Set the drain programme if you set a programme without drain phase Set the drain programme if you set an option which ends with water in the tub The spin phase does not operate or the washing cy cle lasts longer than usual ly Set the spin programme Make sure that the drain filter is not clogged Clean the filter if neces sary Refer to Care and cleaning Adjust manually the items in the tub and start the spin phase again This problem may be caused by balance problems There is water on the floor Make sure that the couplings of the water hoses are tight and there is not water leakages Make sure that the drain hose have no damages Make sure you use the correct detergent and the correct quantity of it You cannot open the appli ance door Make sure that the washing programme is finished Set the drain or the spin programme if there is water in the drum Make sure that the appliance receives electrical power This problem may be caused by a failure of the appliance Contact the Authorised Service Centre If you need to open the door please read carefully Emergency door opening The appliance makes an unusual noise Make sure the levelling of the appliance is correct Refer to
3. Dryness Level Extra Dry For towelling materials Spin Suggested Type of fabric Load kg speed duration rpm mins Cottons and Linen 4 1400 190 210 bathrobes bath towels etc 3 1400 115 135 1 1400 55 65 Spin Suggested Dryness Level Type of fabric Load kg speed duration rpm mins Cupboard Dry Cottons and Linen 4 1400 180 200 For items to put away bathrobes bath towels etc 3 1400 105 125 1 1400 45 65 Cupboard Dry Synthetics and mixed fab 2 1200 95 110 For items to put away rics jumpers blouses underwear 1 1200 45 55 household linen Iron Dry Cottons and Linen 4 1400 150 170 Suitable for ironing sheets tablecloths shirts etc 3 1400 85 105 1 1400 35 45 Wool dry Wool 1 1200 80 100 wool jumpers CONSUMPTION VALUES i The data of this table are approximate Different causes can change the data the quantity and type of laundry the water and ambient temperature i At programme start the display shows the duration programme for the maximum load ca pacity During the washing phase the programme duration is automatically calculated and can be greatly reduced if the laundry load is lower than the maximum load capacity e g Cotton 60 C maximum load capacity 7 kg the programme duration exceeds 2 hours real load 1 kg the programme duration don t reach 1 hour When the appliance is calculating the real programme dur
4. User Manual GETTING STARTED SKS EN User Manual Washer Dryer ZANUSSI SAFETY INFORMATION Before the installation and use of the appliance carefully read the supplied instructions The manufacturer is not responsible if an incorrect installation and use causes injuries and damages Always keep the instructions with the appliance for future reference CHILDREN AND VULNERABLE PEOPLE SAFETY WARNING Risk of suffocation injury or permanent disability This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Do not let children play with the appliance Children of less than 3 years should be kept away unless continuously supervised Keep all packaging away from children Keep all detergents away from children Keep children and pets away from the appliance door when it is open If the appliance has a child safety device we recommend you activate it Cleaning and user maintenance shall not be made by children without supervision GENERAL SAFETY Do not change the specification of this appliance The appliance can be installed as freestanding or below the kitchen counter with correct space Do not install the ap
5. C with a load of 7 kg and the drying programme Cotton Dry are the reference programmes for the data entered in the energy label in compliance with EEC 92 75 standards The water temperature of the washing phase may differ from the temperature declared for the selected programme 2 Woolmark Apparel Care The wool wash cycle of this machine has been approved by The Woolmark Company for the washing of machine washable wool products provided that the products are washed ac cording to the instructions on the garment label and those issued by the manufacturer of this washing ma chine M1380 In UK Eire Hong Kong and India the Woolmark symbol is a certification trademark 3 During this cycle the drum rotates slowly to ensure a gentle washing It can seem that the drum doesn t rotate or doesn t rotate properly Consider this as a normal functioning of the appliance 4 The appliance performs the short heating phase if the water temperature is below 20 C The appliance can show the temperature setting as cold 5 This programme is for daily use and has lowest energy and water consumption maintaining a good washing performance 6 The maximum load refers to cottons items Reduce the load accordingly in case of other type of laundry 7 The maximum spin speed is related to cotton items Set the spin speed Make sure that it agrees with the laundry 8 Woolmark Apparel Care The wool drying cycle of this machine has been approved by The Wool ma
6. Installa tion Make sure that the packaging and or the transit bolts are removed Re fer to Installation Add more laundry in the drum The load may be too small 23 Problem The cycle is shorter than the time displayed Possible solution The appliance calculates a new time according to the laundry load See the Consumption Values chapter The cycle is longer than the time displayed An unbalanced laundry load increases the duration time This is a nor mal behaviour of the appliance The washing results are not satisfactory Increase the detergent quantity or use a different detergent Use special products to remove the stubborn stains before you wash the laundry Make sure that you set the correct temperature Decrease the laundry load You cannot set an option Make sure that you press only the wanted button s The appliance does not dry or does not dry correctly Turn the water tap on Make sure the drain filter is not clogged Reduce the laundry load Make sure you have set the correct cycle if necessary set again a short drying time The laundry is full of differ ent colours fluff The fabrics washed in the previous cycle released fluff of a different colour The drying phase helps to eliminate some fluff Clean the clothes with a fluff remover In case of an excessive amount of fluff in the drum run the speci
7. HH comes on The indicator of the Dll goes off The door lock indicator o goes off You can open the door Remove the laundry from the appliance Make sure that the drum is empty Close the water tap Turn the programme knob to position O to deactivate the appliance Keep the door ajar to prevent the mildew and odours The washing programme is completed but there is water in the drum The drum turns regularly to prevent the creases in the laundry The door lock indicator ais on The indicator DI flashes The door stays locked You must drain the water to open the door To drain the water 1 If necessary decrease the spin speed If you set the appliance only drains 2 Press DI The appliance drains the water and spins 3 When the programme is completed and the door lock indicator D goes off you can open the door 4 Turn the programme knob to position O to deactivate the appliance The appliance drains and spins automatically after approximately 18 hours except for Wool programme STAND BY Some minutes after the end of the washing programme if you do not deactivate the appliance the energy saving status activates DAILY USE DRYING ONLY The energy saving status decreases the energy consumption when the appliance is on the stand by All indicators and the display go off The indicator of the DI flashes slowly Press one of the options to deactivate the energy savin
8. not the detergent dispenser with the flap device add the liquid detergents with a dosing ball supplied by the detergent s manufacturer ECOLOGICAL HINTS Set a programme without the prewash phase to wash laundry with normal soil Always start a washing programme with the maximum load of laundry f necessary use a stain remover when you set a programme with a low temperature To use the correct quantity of the detergent check the water hardness of your domestic system WATER HARDNESS If the water hardness in your area is high or moderate we recommend that you use a water softener for washing machines In areas where the water hardness is soft it is not necessary to use a water softener To know the water hardness in your area contact your local water authority Use the correct quantity of the water softener Obey the instructions that you find on the packaging of the product DRYING HINTS Prepare the drying cycle Open the water tap Do a check if the connection of the drain hose is correct Refer to installation chapter for more information For the maximum laundry load of the drying programmes refer to the drying programmes table ITEMS NOT TO DRY Do not set a drying programme for this laundry Very delicate items Synthetic curtains Pieces of clothing with metal inserts Nylon stockings Quilts Bed covers Duvets Anoraks Sleeping bags Fabrics with residue of hair sp
9. supply is stable I a a ES No communication between electronic elements of the appliance Switch off and switch on again A WARNING Deactivate the appliance before you do the checks Possible solution Make sure that the mains plug is connected to the mains socket Make sure that the appliance door is closed Make sure that there is not a damaged fuse in the fuse box Make sure that the Start Pause has been pressed down If the delay start is set cancel the setting or wait for the end of count Deactivate the Child Lock function if it is on The appliance does not fill with water properly Make sure that the water tap is open Make sure that the pressure of the water supply is not too low For this information contact your local water authority Make sure that the water tap is not clogged Make sure that the filter of the inlet hose and the filter of the valve are not clogged Refer to Care and cleaning Make sure that the inlet hose has no kinks or bends 22 Problem Possible solution Make sure that the connection of the water inlet hose is correct The appliance does not fill with water and drain imme diately Make sure that the drain hose is in the correct position The hose may be too low The appliance does not drain the water Make sure that the sink spigot is not clogged Make sure that the drain hose has no kinks or bends
10. the appliance to pause Press until the display shows D Press DI again to start the programme immediately INTERRUPTING A PROGRAMME AND CHANGING THE OPTIONS You can change only some options before they operate 1 Press Dll The indicator flashes 2 Change the options 3 Press Dll again The programme continues CANCELLING A RUNNING PROGRAMME 1 Turn the programme knob to position O to cancel the programme and to deactivate the appliance 2 Turn the programme knob again to activate the appliance Now you can set a new washing programme Before starting the new programme the appliance could drain the water In this case make sure that the detergent is still in the detergent compartment if not fill the detergent again i OPENING THE DOOR a CAUTION If the temperature and level of the water in the drum are too high and the drum still rotates you cannot open the door While a programme or the delay start operates the appliance door is locked and the display shows the indicator 0 Open the appliance door when the programme or the delay start operates 1 Press DI to pause the appliance 2 Wait until the door lock indicator o goes off 3 Open the door 4 Close the door and press again DI The programme or delay start continues to operate AT THE END OF THE PROGRAMME The appliance stops automatically The acoustic signal operates if it is activated In the display
11. ESCALING If the water hardness in your area is high or moderate we recommend that you use a water descaling product for washing machines Regularly examine the drum to prevent limescale and rust particles To remove rust particles use only special products for washing machine Do this separately from the laundry wash Always obey the instructions that you find on the packaging of the product CLEANING THE DETERGENT DISPENSER MAINTENANCE WASH With the low temperature programmes it is possible that some detergent stays in the drum Make regularly a maintenance wash To do this Remove the laundry from the drum Set the cotton programme with the highest temperature with a small quantity of detergent DOOR SEAL Regularly examine the seal and remove all ob jects from the inner part CLEANING THE DRAIN FILTER WARNING Do not clean the drain filter if the water in the appliance is hot 20 No gt CLEANING THE INLET HOSE AND THE VALVE FILTER EMERGENCY DRAIN Because of a malfunction the appliance cannot drain the water If this occurs do steps 1 through 9 of Cleaning the drain filter If necessary clean the pump When you drain the water with the emergency drain procedure you must activate again the drain system 1 When you drain the water with the emergency drain procedure you must activate again the drain s
12. G The laundry can also be dried with a manual timed drying 1 Press amp again and again to set the time value see the Programmes for timed drying table The display shows 10 minutes Each time you press this touchpad the time value increases by 5 minutes The display shows the set time value for example 40 After some seconds the display shows a new time value 43 The appliance calculates also the duration of the anti crease and the cooling phases 2 Press Dll to start the programme The display shows regularly a new time value The drying indicator starts to flash The display shows the door locked indicator TI If you set only 10 minutes of drying the appliance performs only a cooling phase If the laundry is not sufficient dry set again a short drying time END OF THE DRYING PROGRAMME The appliance stops automatically The acoustic signals operate if they are active DAILY USE WASHING amp DRYING mn In the display Li comes on The indicator DI goes off The last minutes of the drying cycle the appliance performs a cooling and anti crease phase The door is still locked When the door locked U goes off in the display you can open the door 1 Turn the programme knob to O to deactivate the appliance After some minutes from the end of the programme the energy saving function automatically deactivates the appliance 2 Remove the laundry fr
13. NCE OVERVIEW INSTALLATION ON SUSPENDED FLOORING Suspended wooden floors are particularly susceptible to vibration To help prevent vibration we recommend you place a waterproof wood panel at least 15 mm thick under the appliance secured to at least 2 floor beams with screws the wood panel must extend beyond the front feet If possible install the appliance in one of the corners of the room where the floor is more stable FIXING PLATE KIT 4055171146 Available from your authorized dealer Worktop Detergent dispenser Control panel EX Door handle Rating plate J Drain pump filter Feet for the appliance level If you install the appliance on a plinth secure the appliance in the fixing plates Read carefully the instructions supplied with the accessory HOW TO ACTIVATE THE CHILD SAFETY DEVICE This device prevents children or pets to be closed in the drum Turn the device clockwise until the groove is horizontal You cannot close the door N CONTROL PANEL To close the door turn the device anticlockwise until the groove is vertical CONTROL PANEL DESCRIPTION 30 30 M cotton Cotton er Dry Y amp Economy Syne Le e A Synthetics Wool Dry De Wool Rinse zz E Delicates Spin _ Se A Lux Mix 20 Drain by N Super Eco ee m90 m60 m 40 F yo 7 Drying Time Prewash TT Sn g 30
14. al pro gramme to clean it refer to Fluff in the fabrics for more details After the check activate the appliance The programme continues from the point of interruption If the problem occurs again contact the Authorised Service Centre If the display shows other alarm codes Deactivate and activate the appliance If the problem continues contact the Authorised Service Centre EMERGENCY DOOR OPENING In case of power failure or appliance failure the appliance door remains locked The washing programme continues when the power is restored If the door remains locked in case of failure it is CAUTION Make sure that the drum is not rotating Wait till the drum stops rotating if necessary A possible to open it using the emergency unlock feature Before opening the door 24 CAUTION Make sure that the water temperature and the laundry are not hot Wait till they Make sure that the water level inside the drum is not too high Proceed with an emergency drain if necessary refer to Emergency drain in Care and cleaning chapter i cool down if necessary To open the door proceed as follows 1 Turn the selector to O position to switch the appliance off 2 Disconnect the mains plug from the mains socket 3 Open the filter flap 4 Keep the emergency unlock trigger pulled downward and at the same time open the appliance door TECHNICAL DATA 5 Take out the laund
15. ash with a special detergent heavy soil stains Be careful with the curtains Remove the hooks or put the curtains in a washing bag or pillowcase Do not wash in the appliance laundry without hems or with cuts Use a washing bag to wash small and or delicate items e g underwired bras belts tights etc A very small load can cause balance problems with the spin phase If this occurs adjust manually the items in the tub and start the spin phase again STUBBORN STAINS For some stains water and detergent is not sufficient We recommend that you remove these stains before you put the items in the appliance Special stain removers are available Use the special stain remover that is applicable to the type of stain and fabric DETERGENTS AND ADDITIVES Only use detergents and additives specially made for washing machines powder detergents for all types of fabric powder detergents for delicate fabrics 40 C max and woollens liquid detergents preferably for low temperature wash programmes 60 C max for all types of fabric or special for woollens only Do not mix different types of detergents To help the environment do not use more than the correct quantity of detergent Obey the instructions that you find on the on packaging of these products Use the correct products for the type and colour of the fabric the programme temperature and the level of soil If your appliance has
16. ation a dot blinks in the display Energy con Water con Approximate pro Programmes Load kg sumption sumption litre gramme duration mi kWh p nutes Cottons 60 C 7 1 25 70 146 Economy Cotton Energy Saving Pro 7 1 02 53 238 gramme 60 C Cottons 40 C 7 0 78 70 161 Synthetics 40 C 3 5 0 47 50 171 Energy con Water con Approximate pro Programmes Load kg sumption sumption litre gramme duration mi kWh amp nutes Delicates 40 C 3 5 0 53 62 121 Wool Handwash 30 C 1 5 0 25 45 58 1 Cotton Energy Saving programme at 60 C with a load of 7 kg is the reference programme for the data entered in the energy label in compliance with EEC 92 75 standards OPTIONS TEMP 8 Set this option to change the default temperature Indicator cold water The display shows the set temperature SPIN With this option you can change the default spin speed The indicator of the set speed comes on Additional spin options No Spin 6 Set this option to deactivate all spin phases Only the drain phase is available The related indicator comes on Set this option for very delicate fabrics The rinses phase uses more water for some washing programmes Rinse Hold L_ Set this option to prevent the laundry creases The related indicator comes on There is a water in the drum when the programme is completed The drum turns regularly to preven
17. g status i If you set a programme or an option that ends with water in the drum the energy saving status function doesn t activate to remind you to drain the water IN WARNING Refer to Safety chapters DRYING SETTING WARNING Make sure that the water tap is open 1 Turn the programme knob to O to activate the appliance 2 Load the laundry one item at a time 3 Turn the programme dial to the programme applicable for the items to dry The display shows the drying indicator ss i To have a good drying performance do not exceed the maximum drying loads recommended in the user manual Do not set a spin speed lower than the automatic speed of the set programme DRYING AT AUTOMATIC LEVELS The laundry can be dried at pre defined levels of dryness 1 Press ff again and again until the display shows one of the dryness level indicator IRON DRY level indicator for cotton items J CUPBOARD DRY level indicator for cotton and synthetic items EXTRA DRY level indicator for cotton items The display shows a time value calculated on the default load size If the amount of your laundry is more or less than the default size the appliance adjusts automatically the time value during the cycle 2 Press DI to start the programme The display shows the door locked indicator i The drying indicator ss starts to flash You cannot set all dryness levels for any type of laundry TIMED DRYIN
18. he energy consumption decreases and the time of the washing programme is ex tended A Synthetics 3 5 kg Synthetic items or mixed fabric items Nor y 1200 rpm mal soil 60 C X Cold Wool 1 5 kg Machine washable wool hand washable x 1200 rpm wool and delicate fabrics with hand wash 40 C W Cold ing care symbol amp Delicates 3 5 kg Delicate fabrics as acrylics viscose poly 1200 rpm ester items Normal soil 40 C Cold lo Mix 20 3kg Special programme for cotton synthetic and 20 C 900 rpm mixed fabrics with light soil Set this programme to decrease the energy consumption Make sure that the detergent is for low temperature in order to have good washing results Super Eco 3 kg Mixed fabric cotton and synthetic items Cold 1200 rpm by Diain 7 kg To drain the water in the drum All fabrics Sain 7 kg To spin the laundry and to drain the water in the a 4 drum All fabrics 1400 rpm Rinse 7 kg To rinse and spin the laundry All fabrics 1400 rpm OS Wool Dry 1 kg Drying programme for woollen A Synthetics Dry 2 kg Drying programme for synthetic items Cotton Dry 4kg Drying programme for cotton items Maximum load Programme x f Programme description Temperature range e Type of load and soil level Y ET 1 5 kg A short cycle for synthetics and delicate Sn Mi iprogramme 800 rpm items with light soil level or for items to freshen up 1 The washing programme Economy at 60
19. ing dried in the wash dryer Do not use the appliance if industrial chemicals have been used for cleaning Do not dry unwashed items in the wash dryer Items such as foam rubber latex foam shower caps waterproof textiles rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the wash dryer Fabric softeners or similar products should be used as specified by the fabric softener instructions Remove all objects from pockets such as lighters and matches Never stop the wash dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated The final part of a wash dryer cycle occurs without heat cool down cycle to ensure that the items are left at a temperature that ensures that the items will not be damaged Do not use water spray and steam to clean the appliance Clean the appliance with a moist soft cloth Only use neutral detergents Do not use abrasive products abrasive cleaning pads solvents or metal objects Before maintenance deactivate the appliance and disconnect the mains plug from the mains socket SAFETY INSTRUCTIONS INSTALLATION Do not use multi plug adapters and extension cables Do not pull the mains cable to disconnect the appliance Always pull the mains plug Do not touch the mains cable or the mains plug with wet hands Only for UK and Ireland The appliance has a 13 amp mains
20. m20 u m 1400m 1200m 800 400 6 oO amp amp Start Pause Programme knob Spin reduction Spin Temperature Temp EX Display Drying time er Drying Time g Prewash phase LJ Prewash DISPLAY Additional rinse 5 Extra Rinse 8 Automatic drying level Auto Dry E Start Pause Dll Start Pause Delay start Time save amp van be gl 1 se 3 7 Q O 0 GF E D The time area le 5 The programme duration Selected drying time Ch The delay start Eed The alarm codes Cr The message of error i The programme is completed Time programme indicators 77 Normal duration indicator Quick indicator 7 Super quick indicator Delay start indicator FA The child safety lock indicator The door locked indicator jo The indicators of dryness level The drying phase indicator The washing phase indicator PROGRAMMES PROGRAMME CHART Programme Temperature range Maximum load Maximum spin Programme description Type of load and soil level speed Washing programmes Cotton 7kg White cotton and coloured cotton Normal 1400 rpm soil and light soil 90 C X Cold YQ Economy 7 kg White cotton and colour fast cotton Nor 60 C 40 C y 1400 rpm mal soil T
21. new time value The last minutes of the drying cycle the appliance performs the anti crease and the cooling phases WASHING amp TIMED DRYING To have a good drying the appliance does not let you set a too low spin speed for the items to be washed and dried s 1 Press amp to set the drying time value The display shows 10 minutes The indicator comes on in the display The display shows the set drying value time for example 40 After some seconds the display shows the final time value 20 J that is the total duration of the washing and drying cycles washing drying anti crease cooling phases i If you set only 10 minutes of drying after washing the appliance calculates also the duration of the anti crease and the cooling phases 2 Press DI to start the programme In the display the indicator O comes on The door is locked The display shows regularly a new time value END OF THE PROGRAMME The appliance stops automatically The acoustic signals operate if they are active For more information see At the end of the drying programme of the previous chapter 1 Remove the laundry from the appliance Make sure that the drum is empty 2 Keep the door ajar to prevent mildew and odours 3 Close the water tap FLUFF IN THE FABRICS During the washing and or drying phase some types of fabric sponge wool sweatshirt could release fluff HINTS AND TIPS The released fluff co
22. no soil SETTINGS Some programmes accept only one of these options CHILD Lock E With this option you can prevent that the children play with the control panel s To activate deactivate this option press and at the same time until the indicator B comes on goes off You can activate this option After you press DI the options and the programme knob are locked Before you press DI the appliance cannot start PERMANENT EXTRA RINSE With this option you can permanently have an extra rinse when you set a new programme BEFORE FIRST USE To activate deactivate this option press amp and UJ at the same time until the indicator comes on goes off ACOUSTIC SIGNALS The acoustic signals operate when The programme is completed The appliance has a malfunction To deactivate activate the acoustic signals press ff and at the same time for 6 seconds i If you deactivate the acoustic signals they continue operate when the appliance has a malfunction 1 Put 2 litre of water in the detergent compartment for washing phase This activates the drain system 2 Puta small quantity of detergent in the compartment for washing phase DAILY USE WASHING ONLY 3 Set and start a programme for cotton at the highest temperature without laundry This removes all possible dirt from the drum and the tub LOADING THE LAUNDRY Open the water tap Connec
23. om the appliance Make sure that the drum is empty 3 Keep the door ajar to prevent mildew and odours 4 Close the water tap A WARNING Refer to Safety chapters NON STOP PROGRAMME 1 Turn the programme knob to O to activate the appliance 2 Load the laundry one item at a time i To have a good drying performance do not exceed the maximum drying loads recommended in the user manual Do not set a spin speed lower than the automatic speed of the set programme 3 Put the detergent and the additives in the appropriate compartment 4 Turn the programme dial to the washing programme The display shows the indicators of the different washing phases 5 Set the available options WASHING amp AUTOMATIC DRYING 1 Press again and again until the display shows one of the dryness level indicator OF IRON DRY level indicator for cotton items 0 CUPBOARD DRY level indicator for cotton and synthetic items EXTRA DRY level indicator for cotton items The display shows the indicator s The time value on the display is the duration of the washing drying cycles calculated on a default load size i To have a good drying the appliance does not let you set a too low spin speed for the items to be washed and dried 2 Press DI to start the programme In the display the indicator of the set dryness level stays on The door locked indicator U goes on The display shows regularly a
24. pliance behind a lockable door a sliding door or a door with a hinge on the opposite side where the appliance door can not be fully opened Connect the mains plug to the mains socket only at the end of the installation Make sure that there is access to the mains plug after the installation The ventilation openings in the base if applicable must not be obstructed by a carpet Ensure you have good ventilation in the installation room to avoid the back flow of gases into the room from appliances burning other fuels including open fires Exhaust air must not be discharged into a flue which is used for exhausting fumes from appliances burning gas or other fuels if applicable The operating water pressure minimum and maximum must be between 0 5 bar 0 05 MPa and 8 bar 0 8 MPa Obey the maximum load volume of 7 kg refer to the Programme chart chapter The appliance is to be connected to the water mains using the new supplied hose sets Old hose sets must not be reused If the supply cord is damaged it must be replaced by the manufacturer its Authorised Service Centre or similarly qualified persons in order to avoid a hazard Wipe away lint that has accumulated around the appliance Items that have been soiled with substances such as cooking oil acetone alcohol petrol kerosene spot removers turpentine waxes and wax removers should be washed in hot water with an extra amount of detergent before be
25. plug If it is necessary to change the fuse in the mains plug use a 13 amp ASTA BS Remove all the packaging and the transit bolts Keep the transit bolts When you move the appliance again you must block the drum Always be careful when you move the appliance because it is heavy Always wear safety gloves Do not install or use a damaged appliance Obey the installation instruction supplied with the appliance Do not install or use the appliance where the 1362 fuse temperature is less than O C or where it is This appliance complies with the E E C exposed to the weather Directives Make sure that the floor where you install the WATER CONNECTION appliance is flat stable heat resistant and clean Do not install the appliance where the appliance Make sure not to cause damage to the water door can not be fully opened hoses Always move the appliance vertically Before you connect the appliance to new pipes The rear surface of the appliance must be put or pipes not used for a long time let the water against the wall flow until it is clean Make sure that there is air circulation between The first time you use the appliance make sure the appliance and the floor that there is no leakage Adjust the feet to have the necessary space between the appliance and the carpet USE When the appliance is put in its permanent u position check if it is fully level with the aid of a WARNING Risk of injury electrical spiri
26. ramme knob to switch the appliance on and set the required programme The indicator DI flashes The display shows the level of the Time Manager the programme duration and the indicators of the phases of the programme 2 If necessary change the temperature and the spin speed or add available options When you activate an option the indicator of the set option comes on i STARTING A PROGRAMME WITHOUT THE DELAY START Press Dll The indicator of DI stops to flash and stays on The indicator ul starts to flash on the display The programme starts the door locks the display shows the indicator o If you set something incorrect the display shows the message crr The drain pump can operate for a short time when the appliance fills water After approximately 15 minutes from the start of the programme The appliance adjusts automatically the programme duration agree with the laundry load The display shows the new value STARTING A PROGRAMME WITH THE DELAY START 1 Press again and again until the display shows the delay you want to set The related indicator comes on the display 2 Press Dll The appliance starts the countdown The door locks the display shows the indicator o When the countdown is completed the programme starts automatically You can cancel or change the set of the delay start before you press the Dll To cancel the delay start Press DI to set
27. rays nail solvents or similar Garments with foam rubber or materials similar to foam rubber GARMENT LABELS When you dry the laundry obey the indications on the labels of the manufacturers g The item can be tumble dried N rs z The drying cycle is at reduced temperature 1 The item can not be tumble dried The drying cycle is at high temperature DRYING CYCLE DURATION The drying time can change depending on speed of the last spin dryness level type of laundry weight of the load size ADDITIONAL DRYING If at the end of the drying programme the laundry is still damp set a short drying cycle again WARNING To avoid creases of fabrics or shrinks of the clothing do not over dry the laundry GENERAL TIPS Refer to the Drying programmes table to find the average drying times The experience will help you to dry the laundry in a more correct way Take note of the duration drying time of the cycles done before To avoid the static charge at the end of the drying cycle 1 Use fabric conditioner in the washing cycle 2 Use special fabric conditioner for tumble dryers When the drying programme is completed remove the laundry in a short time CARE AND CLEANING IN WARNING Refer to Safety chapters EXTERNAL CLEANING Clean the appliance only with soap and warm water Fully dry all the surfaces CAUTION Do not use alcohol solvents or chemical products D
28. rk Company for the drying of machine washable wool products provided that the products are washed and dried according to the instructions on the garment label and those issued by the manufacturer of this machine M1381 In UK Eire Hong Kong and India the Woolmark symbol is a certification trademark Programme options compatibility Programme CL LL amp Er en e Programme Oo ul amp amp kg E CI m 30 30 1 Only the QUICK option is available 2 Available only if the last spin speed step is lower than 800 rpm PROGRAMMES FOR AUTOMATIC DRYING Dryness Level Type of fabric Load Extra D Cottons and Linen upto4kg For en bathrobes bath towels etc 0 1 Cottons and Linen up to 4 kg en bathrobes bath towels etc Synthetics and mixed fab upto2kg rics jumpers blouses underwear household linen X Iron Dry Cottons and Linen up to 4 kg Suitable for ironing sheets tablecloths shirts etc 1 Hints for test institute The test performance in accordance with EN 50229 must be carried out with a FIRST drying load of the maximum declared drying capacity load composition according to EN61121 by setting the AUTOMATIC CUPBOARD DRY programme for Cotton The SECOND drying load with the residual load must be tested by setting the AUTOMATIC CUPBOARD DRY programme for Cotton PROGRAMMES FOR TIMED DRYING
29. ry and then close the appliance door 6 Close the filter flap Dimension Width Height Depth To tal depth 600 mm 850 mm 522 mm 540 mm Electrical connection Voltage 230 240 V Overall power 2200 W Fuse 13A Frequency 50 Hz Level of protection against ingress of solid particles and IPX4 moisture ensured by the protective cover except where the low voltage equipment has no protection against moisture Water supply pressure Minimum 0 5 bar 0 05 MPa 1 Maximum 8 bar 0 8 MPa Maximum wash load Cotton 7 kg Maximum dry load Cotton 4kg Synthetics 2kg Spin Speed Maximum 1400 rpm 1 The appliance works correctly if the water pressure is not less than 0 05 MPa 0 5 bar If you can not connect the water inlet hose to the cold water tap of the primary hydraulic system connect it to your do mestic cold water storage system Make sure not to have more than a distance of 5 02 m 16 5 ft be tween the appliance inlet hose and the bottom of the water storage tank ENVIRONMENT CONCERNS In Recycle the materials with the symbol TO Put the packaging in applicable containers to recycle it Help protect the environment and human health and to recycle waste of electrical and electronic appliances Do not dispose appliances marked with the symbol a with the household waste Return the product to your local recycling facility or contact your municipal office 25 26 27 WWW ZANUSSI COM SHOP
30. t level If it is not adjust the feet until it is shock fire burns or damage to the appliance ELECTRICAL CONNECTION Use this appliance in a household only WARNING Risk of fire and electrical Do not change the specification of this shock appliance Do not put flammable products or items that are The appliance must be earthed wet with flammable products in near or on the Always use a correctly installed shockproof appliance socket Do not touch the glass of the door while a programme operates The glass can be hot Do not dry the damaged items which contain padding or fillings If you have washed your laundry with a stain remover start an extra rinse cycle before you start a drying cycle Make sure that you remove all metal objects from the laundry Only dry fabrics which are applicable to dry in the washer dryer Follow the instructions on the fabric label Plastic items are not heat resistant Ifyou use a detergent ball remove it before you set the drying programme Do not use a detergent ball when you set a non stop programme PRODUCT DESCRIPTION WARNING Risk of injury or damage to the appliance Do not sit or stand on the open door Do not dry dripping wet clothes in the appliance DISPOSAL Disconnect the appliance from the mains supply Cut off the mains cable and discard it Remove the door catch to prevent children and pets to get closed in the appliance APPLIA
31. t the laundry creases The door stays locked You must drain the water to unlock the door To drain the water refer to At the end of the programme DRYING TIME With this option you can set the time for the fabrics you have to dry The display shows the set value Each time you press this touchpad the time value increases by 5 minutes You cannot set all time values for different types of fabrics i AUTO DRY 55 With this option you can set an automatic level of dryness for the laundry The display shows the symbol of the set level Extra dry level for cotton items Cupboard dry level for cotton and synthetic items O Iron dry level for cotton items PREWASH LI With this option you can add a prewash phase to a washing programme Use this option for heavy soil When you set this option the programme duration increases The related indicator comes on EXTRA RINSE With this option you can add some rinses to a washing programme Use this option for persons allergic to detergents and in areas where the water is soft The related indicator comes on DELAY START With this option you can delay the start of a programme from 30 minutes to 20 hours The display shows the related indicator TIME SAVE C gt Press Time Save to decrease the programme time You can select QUICK to wash items with daily soil 7 SUPER QUICK to wash quickly items with almost
32. t the mains plug to the mains socket 1 Pull the door handle to open the appliance door 2 Put the laundry in the drum one item at a time 3 Shake the items before you put them in the appliance Make sure not to put too much laundry in the drum Refer to max loads indicated in Programme chart 4 Close the door CAUTION Make sure that no laun dry stays be tween the seal and the door There is a risk of water leak age or dam age to the laundry USING DETERGENT AND ADDITIVES Measure out the de tergent and the fabric conditioner Put the detergent and the fabric condi tioner into the com partments Carefully close the detergent drawer DETERGENT COMPARTMENTS Detergent compartment for pre wash phase Detergent compartment for washing phase 4 B 4 Position B for liquid de tergent 5 Close the detergent dispenser Compartment for liquid additives fabric conditioner starch SEE Flap for powder or liquid deter gent AI LIQUID OR POWDER DETERGENT A 1 Position A for powder detergent factory setting 2 Extract the detergent dispenser 3 Turn the flap down wards When you use the liquid deter gent Do not use gelatinous or thick liq uid detergents Do not put more liquid then the maximum level Do not set the prewash phase Do not set the delay start SETTING A PROGRAMME 1 Turn the prog
33. uld stick to the fabrics during the next cycle This inconvenient increases with technical fabrics To prevent the fluff in your laundry we recommend that you To do not wash dark fabrics after you washed and dried light coloured fabrics new sponge wool sweatshirt and the contrary To dry this type of fabrics at open air when they are washed the first time To clean the drain filter After the drying phase clean the empty drum the gasket and the door with a wet cloth HOW TO REMOVE THE FLUFF IN THE GARMENTS To remove the fluff inside the drum set a special programme 1 Empty the drum 2 Clean the drum the gasket and the door with a wet cloth 3 Set the rinse programme Press at the same time LU and s to activate the cleaning function until the display shows CLE 5 Press l to start the programme IN WARNING Refer to Safety chapters THE LAUNDRY LOAD Divide the laundry in white coloured synthetics delicates and wool Obey the washing instructions that are on the laundry care labels Do not wash together white and coloured items Some coloured items can discolour with the first wash We recommend that you wash them separately for the first times Button up pillowcases close zippers hooks and poppers Tie up belts Empty the pockets and unfold the items Turn inside out multilayered fabrics wool and items with painted illustrations Remove hard stains W
34. ystem Put 2 litres of water in the main wash compartment of the detergent dispenser 2 Start the programme to drain the water FROST PRECAUTIONS If the appliance is installed in an area where the temperature can be less than 0 C remove the remaining water from the inlet hose and the drain pump 1 Disconnect the mains plug from the mains socket 2 Close the water tap 3 Put the two ends of the inlet hose in a container and let the water flow out of the hose 4 Empty the drain pump Refer to the emergency drain procedure 5 When the drain pump is empty install the inlet hose again 21 IN WARNING Make sure that the temperature is more than 0 C before you use the appliance again The manufacturer is not responsible for damages caused by low temperatures TROUBLESHOOTING A WARNING Refer to Safety chapters INTRODUCTION The start of the appliance does not occur or it stops during operation First try to find a solution to the problem refer to the table If not contact the Authorised Service Centre With some problems the acoustic signals operate and the display shows an alarm code Eid The appliance does not fill with water properly POSSIBLE FAILURES Problem The programme does not start Ecd The appliance does not drain the water E40 The appliance door is open or not closed correctly Please check the door EHO The mains supply is unstable Wait until the mains
Download Pdf Manuals
Related Search