Hardware User Manual
Contents
1. Reserved Boot from serial SPI Memory Boot from SPI Host slave mode Boot from serial TWI memory Boot from TWI host slave mode Boot from UARTO host slave mode Table 6 3 Boot Mode CM BF537 Types Boot settings for CM BF561 S2 only Switches 1 3 are shown Attention Switch 4 8 are not used for boot mode settings Please refer to section 7 to see the settings for switch 4 8 If you are using a CM BF561 set switches 1 3 of S2 to OFF BEE Off 12345678 DEV BF5xxDA lite V5 x Hardware User Manual 22 Due to the limited number of pins on the two connectors the CM BF561 can only set its boot mode on the core module itself by changing the resistor settings See the CM BF561 manual for further details 7 Usinga Core Module with on board USB If you use a Core Module with USB feature for example the CM BF527 set switch 4 of S2 to on This connects the 5 0V pin of the USB connector X9 to pin 53 of the Core Module If you do not use a Core Module with on board USB feature the switch 4 of S2 should always remain off 8 Installation 8 1 Initial Board Setup The installation guide is written for Windows Windows 2000 and WinXP However for connecting the USB device the drivers for MAC and LINUX are available on the CD In order to set up und test the board the follow the next steps 1 Make sure the Jumper JP1 and JP2 are set and th2. DEV BF548 Lite DEV BF548DA Lite EXT Boards Software Support BLACKSheep LabVIEW uClinux Low cost Blackfin processor Evaluation Board with one socket for any Bluetechnix Blackfin Core Module Additional interfaces are available e g an SD Card Get ready to program and debug Bluetechnix Core Modules with this tiny development platform including an USB Based Debug Agent The DEV BF5xxDA Lite is a low cost starter development system including a VDSP Evaluation Software License Low cost development board with one socket for Bluetechnix CM BF548 Core Module Additional interfaces are available e g an SD Card USB and Ethernet Get ready to program and debug Bluetechnix CM BF548 Core Module with this tiny development platform including an USB Based Debug Agent The DEV BF548DA Lite is a low cost starter development system including a VDSP Evaluation Software License The following Extender Boards are available EXT BF5xx AUDIO EXT BF5xx VIDEO EXT BF5xx CAM EXT BF5xx EXP TR EXT BF5xx USB ETH2 EXT BF5xx AD DA EXT BF548 EXP and EXT BF518 ETH Furthermore we offer the development of customized extender boards for our customers The BLACKSheep VDK is a multithreaded framework for the Blackfin processor family from Analog Devices that includes driver support for a variety of hardware extensions It is based on the real time VDK kernel included within the VDSP development environment LabVIEW embedded su
3. D 14 ee ea aaa 14 Table 4 8 Connector X8 pin ASSIGNMENL ccecsssssesscsssessssssssssecscsssesscsesssscscsssessesesssessessssssescassesscsesssesueseassessessscsucseaeseseeseasassasseassssseess 16 Table 4 9 Connector X7 pin ASSIGNMENK ccecsssesessssssssscsesssssscscsssesscsssssesscsssessesesssessesesssscscsssesscsesssssucsesssessessacsucseseasseeseasassucscassesseees 18 Table 5 1 m u 19 Table 5 2 Core Module Configuration 1 3 are for Boot Mode 19 5 3 SING Nc 19 Table 5 4 Pin assignment of button 56 20 Table 55 Core Module p kikkri ga A OAN 20 Table lH Dia une P 20 Taple5 7 WEDS Tor Tae DEBUG Agent as nn 21 Table 6 1 Boot Mode CM BF527 21 Table 6 2 Boot Mod CM BF53 D a 22 Table 6 3 Boot Mode CM BF537 Type ssssssssssssssscssssssssssssessesssesscscsssssscsesssessessssssesesssessesesssucscsessssssessassessessassusseseasscseasassecseaseesacess 22 Table 10 1 Used without an Extender Board u csssssssssssssscsssssssscessssscscssssssesssssssscoesssscsesssesscscassesssscaesssecsesesesscacass
4. ECHNIX Hardware User Manual EVAL BF5xx V5 X DEV BF5xxDA lite V5 x maximum performance at minimum space Contact Bluetechnix Mechatronische Systeme GmbH Waidhausenstra e 3 19 A 1140 Vienna AUSTRIA EUROPE office bluetechnix at http www bluetechnix com Document No 100 2245 1 1 Document Revision 14 2010 07 13 DEV BF5xxDA lite V5 x Hardware User Manual Table of Contents g 2 PFOQUE IS anne ee an _______________ 5 6 deseo qe E B 7 1 1 guai ii E o 7 2 5 A SCI AO ag carer _________ ____66_____ 9 3 PCB Placement and Mechanical Outline eee e eee eee esee eee tenentes tates tates tata sento te states estote toos esee 10 3 1 10 3 2 Mechanical IULII M EO TERN 11 3 3 79 neuen een tod 12 4 ornate WSS CUO COUN mme ____________ ___ 4 13 4 1 X1 RJ45 Ethernet Connector e asa Pase 13 4 2 X2 SD Card Connector bottom 13 4 3 ByDass e 13 4 4 X4 KOAI T 13
5. 2133584913 SD card Manufacture month 11 SD card Manufacture year 2004 il card Card Status SD card 51 in kb 252168 SD card Checking card for filesystem Error B Found Filesystem FATI6 Partition mounted as sd a Checking slot 1 Mo or illegal card found Error 1 Last address of BLACKSheep 0 2002811 Searching for 16 bit application in flash searching for 8 bit application in flash Ho application found in flash Searching for BS_BO0OT LDR on mass storage device No or invalid file BS was found on mass storage device Terminal ready Have a nice work CH BF361 gt Connected 05 39 05 ANSIW 115200 8 N 1 SCROLL CAPS NUM Capture Print echo This shows a sample boot screen Depending on the current software version you might get different boot Messages 8 You can find a simple hello world program on your support CD or at the download section of the product homepage To start the sample program type xmr UART on your terminal program then Transfer gt Send file select the appropriate file UART lar depending on your Core Module choose protocol Xmodem and send After the download has finished type exec UART to execute the sample program 9 Pressreset to return to the BLACKSheep command line 8 2 Debug Agent Setup Only for DEV BF5xxDA Lite If you have purchased a DEV BF5xxDA Lite board with the Debug Agent mounted on the bottom side of the board you can use it to download and d
6. This 8 pin DIP switch enables the Ethernet connector It is necessary to switch them on for the Core Modules CM BF527 and CM BF537E and off for all others Switch Settings Description NEAR CM BF527 CM BF537E 1273 4567 8 CM BF533 CM BF537U TCM BF537 CM BF561 EERE EEE 1234567 8 Table 5 1 Ethernet Switch 5 2 52 Core Module Configuration 5 2 1 SD Card CS and USB VBUS Switch Settings S2 only 5 8 shown Core Module inserted CM BF527 CM BF533 and CM BF561 CM BF537U CM BF537E and TCM BF537 12345 6 7 8 Table 5 2 Core Module Configuration 1 3 are for Boot Mode only For switch settings 1 3 please refer to chapter 6 Boot Mode Description 5 2 2 CAN Switch Settings S2 only 7 8 shown Core Module inserted CAN enable ADSP BF537 only CAN disable 1234567 8 Table 5 3 CAN disable 5 3 S4 UART Switch Move S4 to position 0 to route the Core Modules RX and TX signals to USB Move S4 to position 1 to route the Core Modules RX and TX signals to X5 DEV BF5xxDA lite V5 x Hardware User Manual 19 5 4 JP1 Power Supply Jumper This jumper can be removed in order to insert an AMPERE METER for current measurement of the entire Core Module 5 5 2 Power Jumper This jumper is used to connect the VddRTC pin of the Core Module to 3 3V You can also use this jumper to connect a battery Vcc to the i
7. 100BaseT Ethernet connection External Power Supply o The board is shipped with 12V external DC DC Power Supply Only available when using the CM BF561 Core Module DEV BF5xxDA lite V5 x Hardware User Manual 8 2 Functional Specification 60 pin Data amp Addr Us Mem Control PPI2 Power RJ 45 Connector DC DC Ethernet Power Supply Connector USB Device Connector USB UART Converter Coremodules CM BF533 5 CM BF537E UART CM BF537U Expansion USB UART uar CM BF561 Debug JTAG Switch TCM BF537 Agent Bypass SD Card SPI CM BF527 DEV BF5xx Connector DA Lite USB CAN T Connector CAN Trasceiver Connector 60 pin PPI 1 SPORTO SPORT1 UART SPI PFs Figure 2 1 Block Diagram Figure 2 1 shows a detailed block diagram of the Dev BF5xx Lite Board Power connector and Power supply The supplied power supply should be used It can deliver up to 1 25A at 12V The input voltage range of an alternative power supply must be within 6 16V and provide at least 9W The on board DC DC power supply generates 5V and 3 3V which are made available on the expansion connectors The maximum current that can be drawn from the 5V is 2A but take care as this includes the current going into the 3 3V regulator a
8. Analog Devices When an external JTAG emulator is attached the on board JTAG is bypassed and the external one is automatically used 4 4 X9 USB Connectors o 4 standard USB B Device Connector for the DEBUG AGENT PC Interface o X6isa standard USB B Device Connector for the USB to UART converter o X9isa standard USB 2 0 OTG Device Connector for the USB versions of the Core Modules 4 5 X5 UART Expansion Pads When S4 is at position 1 the UARTO TX RX is brought to the expansion pins and disconnected from the USB UART Chip Pin No Signal Signal Type 1 RxD Blackfin Input Core Module 2 TxD Blackfin Output Core Module 3 GND 4 3V3 Regulated Power Table 4 3 UART Connector DEV BF5xxDA lite V5 x Hardware User Manual 13 4 6 X7 X8 Expansion Connectors The Expansion Connectors on the Dev BF5xxDA Lite for a stacked height of 16mm are of the following type Part Manufacturer Manufacturer Part Nr X7 X8 AMP Stacked Height 16mm 5 5179010 2 Table 4 4 DEV board connector types The matching connector which is used for building an extender board can be ordered from Bluetechnix Part Manufacturer Manufacturer Part Nr Matching connector AMP 5179031 2 Table 4 5 DEV board matching connector types 4 7 10 Connector Pin No Signal Core Module Signal 1 I O 2 CAN I O Table 4 6 CAN Connector 4 8 X11 Power Connector The board is shipped with a 12V 2A external
9. 0 M IUE 4 20 MK 5 TCH BF537 BE LIBI 7 2 60 le N X8 RxD TxD O 23 40 Figure 3 2 Mechanical Outline Expansion Connector Placement top view DEV BF5xxDA lite V5 x Hardware User Manual 11 ECHNIX 3 3 Extender Footprint If you want to design your own Extension Board for the DEV BF5xxDA Lite you can use the following Board dimensions Figure 3 3 2 65 00 1 2 x2 3 75 00 65 00 y 2 0 8 x2 37 50 3 0 6 0 40 00 1750 75 00 Figure 3 3 Recommended Footprint for Extension Boards top view 5 00 DEV BF5xxDA lite V5 x Hardware User Manual 12 ECHNIX 4 Connector Description In the following the connectors shown in section 3 1 are described 4 1 X1 45 Ethernet Connector Signal Core Module Description 5 Table 4 1 Ethernet Connector 4 2 X2 SD Card Connector bottom mount Signal Core Module Description SD Card 0 DAT2 1 nCS SD 5xx Pin 22 or 55 CD DAT3 2 MOSI Pin 24 CMD UJ NOURA a CD 0 WP 00 Table 4 2 SD Card Connector 4 3 JTAG Bypass Connector The JTAG connector is compliant with any Blackfin JTAG Emulator from
10. 4 5 AS UART EXPAN ON ae nee aan 13 4 6 EXDANSION ONIN en ee A E A TE OAO 14 4 7 CONTET O Beta ga err 14 4 8 AT Gis adeundi aided E 14 4 9 OM Connector 15 4 10 A7 Expansion ONNREIOL 2 a R 17 5 Switches Jumper and LED Deschiption u a anne 19 5 1 51 Ethernet Switch for the CM BF527and the 19 5 2 52 Core Module CONFIGUIATION cessssssessssssesscscsssssecsssssesscscsesscsesssessesesssessesssssucsescsucsescassesseseaesessesesesseseacaeseeseaees 19 5 2 1 SD card CS ana USB BUS 19 5 2 2 een 19 S AVARET Wien RR 19 54d JPT Powesr Supply JUDGE nennen aaa 20 5 5 ee iin erae ee 20 I OIM c c 20 SI USED E 20 5 8 DUNONG 335 Dasein UH 20 5 9 General Purpose LEDS sa cesisssssicsunssaccsssarcsacusepimaravdecardsisneesdeuncessavexsdsussidgousbsesbesabedsensyiuessusovsitebicesesessedenssbepemnusdscenedeistasesens 20 INO tt 20 5 11 LEEDS OF ENS DEBU
11. DC DC Power Supplv which should be used Pin No Signal Description 1 Vin 6V to 16V DC Input Supply Preferable 12V DC 1 2A 3 NC Table 4 7 Power Supply Vin GND Figure 4 1 Power connector To connect to X11 use a DCPP1 e g from Cliff Electronic Components 2 1 25 5mm 9 5mm plug to the power supply Outer contact is GND inner contact is Vin DEV BF5xxDA lite V5 x Hardware User Manual 14 ECHNIX 4 9 X8 Expansion Connector 1 Almost all pins of the Core Modules CM1 connector are connected to the expansion connector X8 Variations are marked RED X8 Pin No CM1 Pin No Detailed Description ______ 9 9 3 3V 10 10 3 3V 20 20 22 22 24 24 26 26 28 nc 30 5 0V 2 32 Vin of X11 37 37 39 39 41 41 43 43 46 46 DEV BF5xxDA lite V5 x Hardware User Manual 15 ECHNIX Table 4 8 Connector X8 pin assignment 1 Maximum current carrying capacity 1A 2 Pin 29 and 30 of the X8 connector are 5V stabilized from the DC DC that can be used for custom add on boards or the extender boards Maximum current carrying capacity 900mA Attention If Core Modules with USB in host mode are used the current must be shared with the connected USB device 3 Pin 31 and 32 of the X7 are Vin of the external power supply minus the input protection diode voltage These pins can be used for custom add on board power supplies Maximum current carrying capacity 1A DEV BF5xxDA lit
12. G EO 21 DEV BF5xxDA lite V5 x Hardware User Manual 2 G BO Mode 21 7 Using a Core Module with on board USB 23 3 01 18 0 A EE UE 23 8 1 Setup Tm 23 8 2 Debug Agent Setup Only for 26 9 Using the VDSP Flash Programming TOol csssessssssssesscsssssecsssssssessssssecscsssesscsssesecsesesssessesssssecseassssecscassesecsesssesseseasees 30 9 1 Developing an Application ang 30 9 2 Overwriting BLACKSheep Code esssssssssssssssssscsssescsssssscsesssessesssssessessssscsesssscscacsesecsesesesecseasaesesucsesssssaeseassessesees 30 10 Extender Board Compatibility List reete neret tette tete tnta tenen 30 10 1 Witnout en meet M 31 10 2 Experimental Extender Board ia bi De HEUTE 31 103 Video Extender gt NR 31 104 Audio Extender BOSE uii ee Nanc Mar E 31 105 Camera Extender BO ecce mentionem MH eee 31 10 6 Analog Digital Digital Analog Converter Extender Board 32 107 Extender SO nenne ee vain lu Ets CONG Ses deu 32 10 8 Video and Audio Extender Board sssuseneeoenoenenoensenensens
13. TCM BF537 CM BF561 Module EXT BF5xx i NT OK OK OK OK AD DA Table 10 6 Used with the Analog Digital Digital Analog Converter Extender Board 10 7 USB ETH Extender Board Core CM BF527 CM BF533 CM BF537E CM BF537U TCM BF537 CM BF561 Module EXT BF5xx Limited Limited Limited OK Limited USB ETH Table 10 7 Used with the USB ETH Extender Board Limited only the USB 2 0 Device functionality is available 10 8 Video and Audio Extender Board Module EXT BF5xx mE 5 Table 10 8 Used with the Video and the Audio Extender Board 10 9 Camera and Audio Extender Board Core ETA BF527 EZ BF533 EZZA BF537E EZEA BF537U TCM BF537 CM BF561 odule Camera UT TM EXT BF5xx l NT NT NT NT NT NT Audio Table 10 9 Used with the Camera and the Audio Extender Board 11 Anomalies For up to date information about this product please consult the product s homepage http www bluetechnix com goto dev bf5xxda lite DEV BF5xxDA lite V5 x Hardware User Manual 32 12 Document Revision History ja ER 2009 05 26 Table 5 3 added 2009 01 26 Picture of boot mode changed Getting started adapted Block diagrams updated 01 12 Chapter 2 Description changed 2008 12 15 Table 4 7 footnotes changed p 2008 05 08 Document Release Pye Pin A
14. al Terms and Conditions AGB Information For further information on technology delivery terms and conditions and prices please contact Bluetechnix http www bluetechnix com Warning Due to technical requirements components may contain dangerous substances The Core Modules and development systems contain ESD electrostatic discharge sensitive devices Electro static charges readily accumulate on the human body and equipment and can discharge without detection Permanent damage may occur on devices subjected to high energy discharges Proper ESD precautions are recommended to avoid performance degradation or loss of functionality Unused Core Modules and Development Boards should be stored in the protective shipping DEV BF5xxDA lite V5 x Hardware User Manual 4 BLACKFIN Products Core Modules TCM BF518 CM BF527 CM BF533 TCM BF537 CM BF537E CM BF537U CM BF548 CM BF561 eCM BF561 The new Core Module CM BF518 is powered by Analog Devices single core ADSP BF518 processor up to 400MHz 32MB SDRAM up to 8MB flash The 2x60 pin expansion connectors are backwards compatible with other Core Modules The new Blackfin Processor Module is powered by Analog Devices single core ADSP BF527 processor key features are USB OTG 2 0 and Ethernet The 2x60 pin expansion connectors are backwards compatible with other Core Modules Blackfin Processor Module powered by Analog Devices single cor
15. e ADSP BF533 processor up to 600MHz 32MB SDRAM 2MB flash 2x60 pin expansion connectors and a size of 36 5x31 5mm Blackfin Processor Module powered by Analog Devices single core ADSP BF537 processor up to 500MHz 32MB SDRAM 8MB flash a size of 28x28mm 2x60 pin expansion connectors Ball Grid Array or Border Pads for reflow soldering industrial temperature range 40 C to 85 C Blackfin Processor Module powered by Analog Devices single core ADSP BF537 processor up to 600MHz 32MB SDRAM 4MB flash integrated TP10 100 Ethernet physical transceiver 2x60 pin expansion connectors and a size of 36 5x31 5mm Blackfin Processor Module powered by Analog Devices single core ADSP BF537 processor up to 600MHz 32MB SDRAM 4MB flash integrated USB 2 0 Device 2x60 pin expansion connectors and a size of 36 5x31 5mm The new Blackfin Processor Module is powered by Analog Devices single core ADSP BF548 processor key features are 64MB DDR SD RAM 2x100 pin expansion connectors Blackfin Processor Module powered by Analog Devices dual core ADSP BF561 processor up to 2x 600MHz 64MB SDRAM 8MB flash 2x60 pin expansion connectors and a size of 36 5x31 5mm Blackfin Processor Module powered by Analog Devices dual core ADSP BF561 processor up to 2x 600MHz 128MB SDRAM 8MB flash 2x100 pin expansion connectors and a size of 44x33mm DEV BF5xxDA lite V5 x Hardware User Manual 5 Development Boards EVAL BF5xx DEV BF5xxDA L ite
16. e V5 x Hardware User Manual 16 ECHNIX 4 10 X7 Expansion Connector 2 Almost all pins of the Core Modules CM2 connector are connected to the expansion connector X7 Variations are marked RED X7 Pin CM2 Pin No Detailed Description 2 62 3 63 4 64 5 65 A 7 67 ied gt 11 71 13 73 14 74 22 82 24 84 26 86 28 88 30 90 39 29 Reset O 100 101 102 103 104 105 106 N UJ Only available if JP5 is mounted 4 DEV BF5xxDA lite V5 x Hardware User Manual 17 47 48 49 50 51 52 53 54 56 57 58 59 60 Note Pin 17 and 44 of the X7 connector are not connected unless the solder jumper 4 and JP5 mounted on the bottom of the DEV BF5xx Lite board The signals of pin 77 and pin 104 of the inserted Core Module are routed directly to the USB connector X9 on the DEV BF5xx Lite board Figure 4 1 shows the position of JP4 and JP5 JP4 connects pin 17 and JP5 connects pin 44 see Figure 4 1 Important To use the DEV BF5xxD A lite in conjunction with the EXT BF5xx USB ETH you have to short JP4 and JP5 107 108 109 110 111 112 113 114 115 116 117 118 119 120 Table 4 9 Connector X7 pin assignment Figure 4 1 Position of JP4 and JP5 ar Kian A User f Ic C VU 5 Switches Jumper and LED Description 5 1 51 Ethernet Switch for the CM BF527and the CM BF537E
17. e shown Switch 4 is not used for boot mode settings so the Boot Modes 8 15 of the CM BF527 cannot be used For details of boot mode 8 15 see the datasheet of the processor Switch Settings Description BMODEO BMODE1 BMODE2 Idle No boot Boot from 8Bit or 16Bit EEPROM Flash Standard boot mode for BLACKSheep uBoot and uClinux Boot from 16 bit asynchronous FIFO Boot from serial SPI Memory Boot from SPI Host slave mode Boot from serial TWI memory Boot from TWI host slave mode Boot from UARTO host slave mode Table 6 1 Boot Mode CM BF527 Type Boot settings for CM BF533 S2 only Switches 1 3 are shown Switch Settings Boot Mode Description BMODEO BMODE1 Execute from16Bit ext mem Bypass ROM Standard boot mode for uBoot uClinux 12345678 DEV BF5xxDA lite V5 x Hardware User Manual 21 Boot from 8Bit or 16Bit EEPROM Flash Standard boot mode for BLACKSheep Boot from SPI 8Bit Boot from SPI 16Bit 12345678 Table 6 2 Boot Mode CM BF533 Boot settings for CM BF537E CM BF537U and TCM BF537 S2 only Switches 1 3 are shown Switch Settings Boot Mode Description BMODEO BMODE1 BMODE2 Execute from16Bit ext mem Bypass ROM Standard boot mode for uBoot uClinux Boot from 8Bit or 16Bit EEPROM Flash Standard boot mode for BLACKSheep
18. e switch 54 is in position 0 as shown in Figure 8 1 Console USB Connector Figure 8 1 Setup of the DEV BF5xxDA Lite Board 2 Setswitch S2 according chapter 5 2 and 6 Set switch S1 according chapter 5 1 3 Connectthe power supply to the power connector of the DEV BF5xxDA Lite board 4 Connect the DEV BF5xxDA Lite Board via USB to the PC The pre flashed BLACKSheep starts and the LED mounted on the EVAL board starts blinking On the PC usually the Found New Hardware Wizard opens DEV BF5xxDA lite V5 x Hardware User Manual 23 Welcome to the Found New Hardware Wizard Windows will search for current and updated software by looking an pour computer an the hardware installation CD or on the Windows Update Web site with your permission Head our privacy policy Can Windows connect windows Update ta search for software C Yes this time only C Yes now and every time connect a device not this time Click Next to continue If the wizard asks connect to the windows update site select No not this time Found New Hardware Wizard E This wizard helps you install software far USB ta Bridge Controller Q If your hardware came with an installation CD ar floppy disk insert it now What do you want the wizard to C Install the software automatically Recommended Click Nest to continue Back Cancel Choose Install from a list or
19. ebug your software with the VDSP development environment from Analog Devices An evaluation version is included in the support CD or you can download it from our website or the website from Analog Devices Currently the Debug Agent works only with version 4 5 of the VDSP IDE Note The Core Module will get warm while in use Please follow the instructions for installing and configuring VDSP to work with the Debug Agent 1 Install VDSP 4 5 2 If available install the latest update for VDSP 4 5 You can download updates from the Analog Devices website 3 Configure VDSP 4 5 to support the DEV BF5xxDA Lite by starting the Installer from your support CD Once started you should see the following dialog Note To run the installer the net framework is required DEV BF5xxDA lite V5 x Hardware User Manual 26 BLUE ECHNIX Installation progress o 4 Selectthe Core Module that you have inserted in the socket of your DEV BF5xxDA Lite 5 Press the Install button 6 You should get the following message 7 Besurethat the board is powered on 8 Connect X4 USB JTAG with a USB cable to a free USB port on your 9 Thefollowing dialog or a similar one should appear Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for USB Device If your hardware came with an installation CD or floppy disk insert it now What do you want the
20. elect Connection Type Select Processor Select Connection Type Select the type of target that you would like to connect to Select Platform EZKIT Lie gt Finish C Emulator C Simulator C Legacy target Configurator Licenses Licenses Clicking this button will launch the license manager From which you can add and view licenses teen 4 Select the platform that you have created with the VisualDSP Configurator and press Finish Select Platform Provide a name For the session and choose the specific platform it will connect to If connecting to an emulator and do not see an appropriate platform in the list click the Configurator to create one Welcome ifs Select Platform E Select Processor G Select Connection Type Session name 4DSP BF537 Bluetechnix CM BF537 Select Platform Finish Select your platform v ADSP B ite via Debug Agent Bluetechnix CM BF537 Show all platforms Configurator Licenses Next Go to the next page lt Back Next gt Finish Cancel 29 Now the session is ready and VDSP should start with these settings The Core Module on the DEV BF5xxDA Lite is now ready for debugging For further information about the session wizard and the VDSP tools please refer to the VDSP manuals downloadable from the Analog Devices website If you change your Core Module on the DEV BF5
21. eseestacsesseaeacseesears 31 Table 10 2 Used with the Experimental Extender Board sssssesennnnzanminzaznnnnnznninnninesnnzzzannninzznzentrtinzanananaenerezzznnenananznstsnznzaa 31 Table 10 3 Used with the Video Extender Board FFS tote tt stata 31 Table 10 4 Used with the Audio Extender Board u cssssssssssssssssscsssssssscssssssssssssssssscsssessesesssesscsssessesescsssessessassesscsesesessesssssecseasessscess 31 Table 10 5 Used with the Camera Extender Board eee eee entere tentato testata tates 31 Table 10 6 Used with the Analog Digital Digital Analog Converter Extender Board sss 32 Table 10 7 Used with the USB ETH Extender Board cesssssssssssssssssscsssssscsssssssscscsssessesssssesscsesssecsesesesessesesssesecsesesessessassecseassssecens 32 Table 10 8 Used with the Video and the Audio Extender Board cessssssssssssssesesesssssseesesessssssesescsesesesessesesesesesesesssseseseseseacsees 32 Table 10 9 Used with the Camera and the Audio Extender Board sssssenenzannanznnnnnnnnnzaznnannannnennnnnannnsnnnanznzennznnenananznznsnanzna 32 Table 1215 Revision qd dh 33 DEV BF5xxDA lite V5 x Hardware User Manual 34
22. ge device socket 1 1 Overview The DEV BF5xx Lite Board includes the following components 60 Pin Expansion Connector 2 DC DC Power Supply 5V and 3V3 USB to UART Coremodules CM BF533 CM BF537E DEBUG CM BF537U USB OTG TCM BF537 SD Card CM BF527 45 for CM BF537E CAN CM BF527 60 Pin Expansion Connector 1 Figure 1 1 Overview of the Dev BF5xx Lite Board DC DC Converters o 5V 2A 3V3 1 5A draws its power from the 5V output of the DC DC 1 Core Module Slot o Supports all current Bluetechnix Blackfin based Core Modules DEV BF5xxDA lite V5 x Hardware User Manual 7 ECHNIX o Supports up to 915kbps UART USB conversion o Emulates a standard COM port on the computer o Drivers for Windows and Linux available u JTAG JTAG Plug that supports all analog Devices JTAG Emulators Expansion Connector 1 o SPORTO o UART o SPI o PPI1 Parallel Port Interface 1 o PFs Programmable Flags Expansion Connector 2 o DataBus o Address Bus o Memory Control Signals o PPI2 Parallel Port Interface 2 o PowerSupply 2 05 Connector optional o Can only be used together with the CM BF527 including USB2 0 OTG interface or the CM BF537U Core Module which has an on board NETPLX 2272 USB2 0 Device Chip RJ 45 Ethernet Plug o Only in combination with the CM BF527 and the CM BF537E module o Standard 10BaseT
23. ing tables show possible Board combinations DEV BF5xxDA lite V5 x Hardware User Manual 30 10 1 Without an Extender Board C gt CM BF527 CM BF533 CM BF537E CM BF537U TCM BF537 CM BF561 Module N gt OK OK OK OK OK OK Extender Table 10 1 Used without an Extender Board 10 2 Experimental Extender Board C E CM BF527 CM BF533 CM BF537E CM BF537U TCM BF537 CM BF561 Module EXT BF5xx idm OK OK OK OK OK OK EXP Table 10 2 Used with the Experimental Extender Board All boards can be used in combination with the Experimental Extender Board 10 3 Video Extender Board C CM BF527 CM BF533 CM BF537E CM BF537U TCM BF537 CM BF561 Module EXT BF5xx OK OK OK OK OK Video Table 10 3 Used with the Video Extender Board 10 4 Audio Extender Board C rn CM BF527 CM BF533 CM BF537E CM BF537U TCM BF537 CM BF561 Module EXT BF5xx SEDE NT NT NT NT NT NT Audio Table 10 4 Used with the Audio Extender Board 10 5 Camera Extender Board CM BF527 CM BF533 CM BF537E CM BF537U TCM BF537 CM BF561 EXT BF5xx Camera Table 10 5 Used with the Camera Extender Board Mono Camera or Display Stereo Camera or Mono Camera and Display DEV BF5xxDA lite V5 x Hardware User Manual 31 10 6 Analog Digital Digital Analog Converter Extender Board C us CM BF527 CM BF533 CM BF537E CM BF537U
24. lso because this regulator is powered by the 5V The maximum current that can be drawn from the 3 3V is 1 5A but note that this means at least 1A additional load on the 5V connector The serial port of the Core Module can be routed directly to the USB Port USB UART or to the UART Expansion Pads An SD Card connector mounted at the bottom of the board allows making use of file IO functions delivered with the BLACKSheep software BLACKSheep supports SD Cards and includes a FAT file system as well as the most relevant file IO functions The complete BLACKSheep software package can be purchased from Bluetechnix The 2 USB device connector colored in purple can only be used with the CM BF527 Core Module featuring USB2 0 OTG and the CM BF537U Core Module which has an on board USB V2 0 Device NET2272 by PLX technology The RJ 45 Ethernet connector colored in purple can only be used in combination with the CM BF527 or the CM BF537E Core Module which has an on board Ethernet physical chip DEV BF5xxDA lite V5 x Hardware User Manual 9 3 PCBPlacement and Mechanical Outline 3 1 PCB Placement 1 JP X3 Ext JTAG X4 USB JTAG X10 CAN X5 Uart Figure 3 1 Connector PCB Placement DEV BF5xxDA lite V5 x Hardware User Manual USB UART 3 2 75 00 Mechanical Outline 57 50 Bu HUM m 2 1500 m 000
25. nnensenensensnnensensnnensnnensenensensnsensnsensensnsensensnsensnsensssensenensensenen 32 10 9 Camera and Audio Extender Board useseoseneeoenoensenensensnnensnsensenensensnnensensnnensnnensenensensnsensensnsensnsensensnsensesensenensensenen 32 11 nien wv 32 12 Document Revision 33 A Listof Figures and Tables 33 DEV BF5xxDA lite V5 x Hardware User Manual 3 Edition 2008 09 O Bluetechnix Mechatronische Systeme GmbH 2008 All Rights Reserved The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics Terms of delivery and rights of technical change reserved We hereby disclaim any warranties including but not limited to warranties of non infringement regarding circuits descriptions and charts stated herein Bluetechnix makes and you receive no warranties or conditions express implied statutory or in any communication with you Bluetechnix specifically disclaims any implied warranty of merchantability or fitness for a particular purpose Bluetechnix takes no liability for any damages and errors causing of the usage of this board The user of this board is responsible by himself for the functionality of his application He is allowed to use the board only if he has the qualification More information is found in the Gener
26. nternal RTC of the Blackfin For connecting GND use pin 3 of the UART expansion pads 5 6 JP3 For the CM BF527 JP3 is used to connect the USB ID pin to the Core Module For all other Core Modules leave it open 5 7 JP6USB ID For the CM BF527 JP6 is used to force the USB OTG master mode For all other Core modules leave it open 5 8 Buttons 53 S6 The Button 593 is the main Reset Button of the Core Module The Button S6 is a general purpose input button on pin 18 of the Core Module Core Module Button S6 CM BF527 PF14 CM BF533 PF5 CM BF537U PG14 CM BF561 PF46 TCM BF537 PG14 CM BF537E PG14 Table 5 4 Pin assignment of button S6 5 9 General Purpose LEDs The LED V14 indicates that the board is powered The LED s V9 and V10 are connected to general purpose 10 pins 45 and 16 respectively Core Module LED V10 CM BF527 PF10 CM BF533 PF9 CM BF537E PG10 CM BF537U PG10 CM BF561 PF42 TCM BF537 PG10 Table 5 5 Core Module LEDs 5 10 Ethernet LEDs Designator Color Function V1 Yellow Full Duplex V2 Green Activity V3 Green 100MB Speed LED Table 5 6 Ethernet LEDs DEV BF5xxDA lite V5 x Hardware User Manual 20 5 11 LEDs of the Debug Agent Designator Color Function Table 5 7 LEDs for the Debug Agent 6 BootMode Description Only switch 1 3 of S2 are described in this section Please refer to section 5 2 to see the settings for switch 4 8 Boot settings for CM BF527 S2 only Switches 1 3 ar
27. pport for Bluetechnix Core Modules is done by Schmid Engineering AG http www schmid engineering ch All the Core Modules are fully supported by uClinux The required boot loader and uClinux can be downloaded from http blackfin uClinux org Upcoming Products and Software Releases Keep up to date with all the changes to the Bluetechnix product line and software updates at http www bluetechnix com BLACKFIN Design Service Based on more than five years of experience with Blackfin Bluetechnix offers development assistance as well as custom design services and software development DEV BF5xxDA lite V5 x Hardware User Manual 6 BLUE ECHNIX 1 Introduction NOTE The DEV BF5xxDA Lite has an on board Debug Agent which is not available on the EVAL BF5xx Board All other features are identical In this document when describing both boards the name DEV BF5xx Lite is used The DEV BF5xx Lite Board is a lightweight development platform for all current and future Bluetechnix Core Modules CM BF527 CM BF533 CM BF561 CM BF537U CM BF537E TCM BF537 On the DEV BF5xxDA Lite board a bottom mounted tiny high performance Debug Agent fully compatible with Visual DSP allows programming and debugging any of the Blackfin Processors The small baseboard has all hardware necessary to test the performance of the Core Modules including a high speed serial port directly connectable to a computer USB port a CAN Interface and an SD Card mass stora
28. specific location The driver is located on your support CD DEV BF5xxDA lite V5 x Hardware User Manual 24 Please choose your search and installation options Lal M STOVE This procedure has to be done twice because at first the USB driver will be installed Then the Hardware Wizard opens again because the UART bridge driver has to be installed in addition using the same driver file Simply repeat this step 5 Open Windows device manager Control Panel gt System gt Hardware to see which COM port number has been assigned to the CP2101 UART to USB Chip This number differs from computer to computer based on the already installed COM ports e g 4 6 Open a Terminal program like HyperTerminal included in Windows operating systems and open the respective COM port with 115200 Baud 8 Data bits No Parity and 1 Stop bit disable the Hardware flow control 7 Reset the DEV BF5xxDA Lite Board Press the main reset button After this you will see the BLACKSheep boot screen showing up If you disconnect the device you have to reconnect DEV BF5xxDA lite V5 x Hardware User Manual 25 ECHNIX g com 1 HyperTerminal l Bl xl File Edit View Call Transfer Help Checking for SD cards Checking slot Card found Checking card SD card Command response B SD card Product name SD256 SD card Manufacturer ID SD card Application ID SD card Product revision gt SD card Serial number
29. ssignment Changed m to 5 04 Several Changes IN mE 04 01 Extender Board Compatibility List 2007 03 01 Initial release of the document Table 12 1 Revision History A List of Figures and Tables Figures Figure 1 1 Overview of the Dev BF5xx Lite Board sssrsnnznzanznzanenzanennazananzananzananzanonanzananponanzananansenananzananzanananzananzananzanansnnananzananzata 7 Figure 2 1 BIOcK DI GA ee 9 Figure 3 1 Connector PCB Placem ii een een ee ren 10 Figure 3 2 Mechanical Outline Expansion Connector Placement top view 11 Figure 3 3 Recommended Footprint for Extension Boards top 12 Figure4 T Position or JPS ea en 18 Figure 8 1 Setup of the DEV BF5xxDA Lite Board eee eee eee ee teen tente tentato ta tentata senta testa totes tote npnzonanzananzanananzanaa 23 DEV BF5xxDA lite V5 x Hardware User Manual 33 BLUE ECHNIX Tables intel o tmt 13 Table 2 2 SD Care anode 13 He tub ip e MUS 13 Table 4 4 DEV board connector typ6s sek 14 Table 4 5 DEV board matching connector tyPES csssssssesecscsssesscsssssscsesssessescsssessessssscsssssessesssssecsescsssessessssscsesesesessesesssasscassesecees 14 130245 CAN taka nad eee
30. the Session List window that appears on startup of VDSP 2 Selectthe processor corresponding to your Core Module and press Next DEV BF5xxDA lite V5 x Hardware User Manual 28 DEV BF5xxDA lite V5 x Hardware User Manual Session six Select Processor Choose a target processor sy Welcome Select Processor Select Processor E 2 00 Select Connection Type Processor family Blackfin I Select Platform Finish Choose a target processor Processor Description ra ADSP BF531 Blackfin Processor 800 MMACS 52K bytes 03 ADSP BF532 Blackfin Processor 800 MMACS 84K bytes on PA ADSP BF533 Blackfin Processor 1512 MMACS 148K bytes o 02 ADSP BF534 Blackfin Processor 500 2 132K bytes on chi 02 ADSP BF535 Blackfin Processor 700 MMACS 308K bytes on 03 ADSP BF536 Blackfin Processor 100K bytes on chip memory ADSP BF53 Blackfin Processor 132K bytes on chip memory Show all processors Configurator Licenses Choose a target processor Displays the list of processors that belong to the specified family processor is grayed out if it is not licensed and the Show all processors option is checked lt Back Next gt 3 Select EZ KIT Lite and press Next Select Connection Type Choose the type of connection that you would like establish For the previously chosen processor below Welcome S
31. wizard to do Install the software automatically Recommended Install from list or specific location Advanced Click Next to continue 10 Choose Install the software automatically press Next and follow the on screen instructions After the install process you have to create a Platform using the Platform Wizard of the VDSP Follow the instructions to create a valid Platform for the Bluetechnix USB Debug Agent 1 Open the VisualDSP Configurator from the start menu entry of VisualDSP 4 5 2 Select New 3 In the Type box select the Bluetechnix entry corresponding to the Core Module on your DEV BF5xxDA Lite board 4 Entera Name for the Platform for example Bluetechnix CM BF537 DEV BF5xxDA lite V5 x Hardware User Manual 27 ECHNIX Platform Properties Bluetechnix CM BF537 j gt _____ Device 0 LInknown TE 5 Select Ok The created platform should appear in the Platforms section of the configurator window E VisualDSP Configurator H9 ADSP 21065L EZ KIT Lite ADSP 21160 EZ KIT Lite EB ADSP 21161 EZ KIT Lite 6 Press Ok to close the VisualDSP Configurator The last step is the creation of a VDSP debug session Follow the instructions below 1 Open the New Session Wizard from the pulldown menu of the VDSP Session New Session or press the New Session button on
32. xxDA Lite you have to reconfigure VDSP starting with the install tool as described above 9 Usingthe VDSP Flash Programming Tool 9 1 Developing an Application If you are developing your own projects with the VDSP development tools including the JTAG provided by Analog Devices you can use the flash programming tool included in the VDSP environment in order to flash your program on the Core Module You have to load the flash driver located on your EVAL board support CD corresponding to the inserted Core Module 9 2 Overwriting BLACKSheep Code If you overwrite intentionally or unintentionally the section in the flash containing the BLACKSheep code you will need a JTAG device and the VDSP flash tool to reprogram the flash Flashing the appropriate BLACKSheep loader file Idr located on CD reinstalls the BLACKSheep code The examples drivers and the BLACKSheep software are under permanent development Please refer to the download section of www bluetechnix com to get the latest versions or updates 10 Extender Board Compatibility List This chapter points out the compatibility of the EVAL BF5xx and DEV BF5xxDA Lite with Core Module and Extension Boards Please refer to the Extender board and Core Module Hardware Manuals for further information Legend OK Full functional OK Functional but not all features are available NO Not functional NG Functionality not guaranteed NT Not tested yet Limited Limited In the follow
Download Pdf Manuals
Related Search