User`s Manual for the M5-1003 DVI/USB/RS-232 and Audio
Contents
1. 2011 Opticis All Rights Reserved Revision 1 3 pTIcis www opticis com DVI USB RS 232 and Audio Optical Extender User s Manual Opticis Locations f OF th M 5 1 003 Headquarters Opticis Co Ltd 304 Byucksan Technopia 434 6 Sangdaewon Dong Chungwon Ku Sungnam City Gyeonggi Do 462 716 South Korea Tel 82 31 737 8033 8 Fax 82 31 737 8079 ATO FA g www opticis com A C For order support please contact your Distributor or Reseller For technical support check with the Opticis web site www opticis com or contact techsupp opticis com Manual Contents Manual Contents Welcome Product Description system Requirements for Setup Installation Operation Guide Self EDID Programming Procedure RS 232 cabling Troubleshooting Maintenance Technical Support Product Specifications Warranty Information Regulatory Statements Pictorials Figure 1 Overall Connection of M5 1003 Optical KVM Extender Figure 2 Connection of DVI USB RS 232 and Audio Cable to Transmitter Figure 3 Connection of Local Display and Keyboard Mouse Figure 4 Connection of DVI Cable Keyboard and Mouse to Receiver Figure 5 Connection of Two 2 Duplex LC Optical Fibers Figure 6 Connection of AC DC Power Adapter Figure 7 Switch for Selection Control Position Figure 8 Connection of Remote Switch and Indicator Figure 9 Position of EDID PRGM Button and Self EDID LED Figur2. installation procedure below Improper or no operation may result if the start up sequence is not correctly followed Step 1 Carefully unpack the contents of the shipping group Step 2 With system power turned off connect the Transmitter module to the DVI receptacle of PC or other video source equipment by a DVI copper cable If necessary connect the RS 232 cable and the audio cable to D sub 9 pin connector and audio jack Analog Audio Input DVI USB RS232 Input Control Server or PC Figure 2 Connection of DVI USB RS 232 and Audio Cable to Transmitter Module Step 3 Connect the Transmitter module to the display keyboard and mouse for local control You may skip Step 3 if you don t need local control In this case please see instructions on page 1 6 for Self EDID programming A a L Ze W lt Local Display A ts i Local Keyboard Mouse Se S y SS gt Ag Analog Audio Input re g DVI USB RS232 Input FS Control Server or PC j Figure 3 Connection of Local Display and Keyboard Mouse 1 3 Installation Step 4 Connect the Receiver module to the remote display keyboard and mouse If necessary connect the RS232 cable and the audio cable to audio output device and RS 232 device For proper RS 232 cable type please refer to Fig 10 PB BO Romote Display oS Remote Keyboard Mouse SS ie ie WA iad tein RS232 Output Device Figure 4 Connection of DVI cable keyboard and mouse
3. is decided by console switch Use of Console Switch and Indicator Console switch and indicator are optionally provided for easy and convenient control conversion Connection is like below picture Caution Please DO NOT look directly into the LC receptacles of Uplink module while they are powered on although they are regulated strictly enough to operate under the Laser Class 1 classified by CDRH FDA for eye safety 1 5 Oneration Guide Self EDID Programming Procedure The graphic source equipment generally requires communication of display information EDID Display information EDID contains resolution and timing information for your display Basically M5 1003 supports DDC2B with the local display M5 1003 also offers Self EDID programming Self EDID programming means that the EDID from the display is stored in the transmitter You should use Self EDID feature if you don t connect local monitor Follow these steps to record the EDID of the display into the transmitter unit Note1 If you know that EDID is not required by the source Auto EDID programming is not necessary Note2 The default EDID in factory ship out is programmed in the VESA standard of UXGA 1600x1200 60Hz Step 1 Power on the display Step 2 Insert the included 12V DC power adapter into the transmitter Step 3 Push the EDID PRGM button of the transmitter with a narrow pin After three times blinking of Self EDID LED it will stay on Self EDID
4. to Receiver Module Step 5 Remove dust covers and connect two 2 duplex LC fibers to LC receptacles of the Transmitter and Receiver modules as shown in Fig 5 Ensure the order of the duplex LC connectors is correct Figure 5 Connection of Two 2 Duplex LC Optical Fibers Step 6 Connect an AC DC power adapter to both Transmitter and Receiver modules as your availability of AC outlets You can find power indication LED lit on in the both modules x LS A Figure 6 Connection of AC DC Power Adapter Step 7 Power ON the PC and display Power on connected USB audio and RS 232 devices too For proper RS 232 cable type please refer to Fig 10 Tip 1 Avoid hot plugging the Uplink as this is not recommended practice with live digital voltages 1 4 Installation Operation Guide Selection of Control Position mS 1OG Con cis O SEDO O pkb O Power O la O ama O Optica TRANSMNNNISA Switch for decision of control position Figure 7 Switch for Selecting Control Position Graphic data is always transmitted to both local DVI out and remote DVI out However USB port for keyboard and mouse is selectable for control at specific position Controllable site is like the table below with the position of switch on the front panel of transmitter The position of Local Keyboard Mouse Remote Keyboard Mouse Switch 2 USB ports on Tx 4 USB ports on Rx Remote Disable Enable eee Console Control position
5. LED ms 1I005 bp Ticis KVM Oma titan GFTIECAL OVV RS HEE UEEAUDIO EXTENDER Oum Ofaa Ocma TRANSMITTER EDID PRGM Button Figure 9 Position of EDID PRGM Button and Self EDID LED Step 4 Connect the Local Display port in transmitter to the display while turned on over DVI cable The LED on the front panel will begin to blink rapidly Blinking indicates reading the EDID LED will be turned OFF after blinking for about 8 sec The monitor EDID has been recorded Step 5 Disconnect the transmitter from the display Then LED ON again 1 6 Self EDID Programming Procedure RS 232 Cabling 1 When you connect PC to PC over RS 232 with M5 1003 please use male to female straight type cable between PC and M5 1003 TX and male to male cross type cable between PC to M5 1003 RX PC PC Male to Female Male to Male Straight Cable Cross Cable RS232_Male M5 1003 TX M5 1003 RX 2 When you connect PC to RS 232 device DUT over RS 232 with M5 1003 please use male to female straight type cable between PC and M5 1003 TX and male to female straight type cable between RS 232 device to M5 1003 RxX PC DUT RS232_ Female Male to Female Male to Female Straight Cable Straight Cable RS232_ Female RS232_Male M5 1003 TX M5 1003 RX Figure 10 Proper RS 232 cable type around M5 1003 1 7 RS 232 Cabling Troubleshooting The display shows only black screen e Check that all AC and DC plugs and jacks u
6. e 10 RS 232 cable type around M5 1003 1 0 1 1 1 2 1 3 1 5 1 6 1 7 1 8 1 9 1 10 1 11 1 3 1 3 1 4 1 4 1 4 1 5 1 5 1 6 1 7 Welcome Congratulations on your purchase of the M5 1003 DVI USB RS 232 and audio optical extender This manual contains information that will assist you in installing and operating the product Product Description M5 1003 offers extremely long extension of DVI USB serial control data and audio up to 2 km over single mode fiber cables with two 2 duplex LC connectors It is tremendously long over the limits of copper extensions like a few of meter of DVI and USB Designed for high resolution performance it guarantees lossless image quality and no frame dropping to deliver perfect graphic data transmission up to WUXGA 1920x1200 at 60Hz refresh rate It is designed to multiplex and de multiplex DVI USB RS232 and stereo audio so as to be linked over four 4 single mode LC fibers at 1310nm 1550nm It provides Self EDID programming feature that makes the installation of M5 1003 more easy and flexile at any variable resolution Optionally we could include convenient remote console switch and indicator for selecting local control or remote control Shipping Group of M5 1003 DVI USB Audio and RS 232 optical extender O Tx and Rx boxes One Transmitter module amp One Receiver module O AC DC power adapter Two 12V 3A units including AC cord Oo User s Manual O Option Remote cons
7. nse repair the defective product or part deliver to customer an equivalent product or part to replace the defective item or refund to customer the purchase price paid for the defective product All products that are replaced will become the property of Opticis Replacement products may be new or reconditioned Any replaced or repaired product or part has a ninety 90 day warranty or the reminder of the initial warranty period whichever is longer Opticis shall not be responsible for any software firmware information or memory data of customer contained in stored on or integrated with any products returned to Opticis for repair under warranty or not Warranty Limitation and Exclusion Opticis shall have no further obligation under the foregoing limited warranty if the product has been damaged due to abuse misuse neglect accident unusual physical or electrical stress unauthorized modifications tampering alterations or service other than by Opticis or its authorized agents causes other than from ordinary use or failure to properly use the product in the application for which said product is intended Dispose of Old Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate systems This symbol on the product or on its packaging indicates that this product shall not be treated as household waste Instead it shall be handed over to the applicable collection point for the rec
8. ole switch and indicator Duplex LC Patch Cord Single or Multi mode glass fiber Local Control Remote Control Romote Display Remote Keyboard Mouse Local Display Local Keyboard Mouse Analog Audio Input a Foy amp ME Audio amp gt TY D g 4 Output Device DVI USB RS232 Input U7 Sp we CO woe Control Server or PC bg ai ae Figure 1 Overall connection of M5 1003 Optical KVM Extender 1 1 Welcome Product Description System Requirements for Setup O Hardware requirements Local display and remote display should have same graphic resolution m You have a graphic controller card with a DVI port in your Windows Mac Mac is option or SUN system It should support the maximum graphic resolution feature of the display to be connected m In case of using a computer no special memory size CPU speed and chipsets are required E Proper initial trial of the entire platform with its application using a short length copper cable is recommended prior to install with the optical link O Software requirements No special needs if the DVI graphic controller and display peripheral are operational with the platform s OS and application O AC DC Power Adapter Technical Advisory The power of M5 1003 is designed to supply to each module of Transmitter and Receiver modules by plugging to each of the power plugs 1 2 System Requirements for Setup Installation Important Please use the
9. sed by external power supplies both Opticis and others are firmly connected e Ensure that power LED lit ON e Ensure that the Transmitter and Receiver modules connected correctly to the PC and display respectively e Check if the PC and display are powered on and properly booted e Reset the M5 1003 using Reset button on Uplink and Downlink modules e Re boot up the system after reconnecting the LC optical fibers Screen is distorted or displays noises e Check if the graphic resolution is properly set Go to the display properties and tap the settings e Reset the M5 1003 using Reset button on Transmitter and Receiver modules e Reset the system e Power down disconnect and reconnect the LC optical fiber or DC power adaptors and power up Maintenance No special maintenance is required for this product Ensure that this product is stored or used in a benign environment free from liquid or dirt contamination There are no user serviceable parts Refer all service and repair issues to Opticis or its authorized distributor Technical Support and Service For commercial or general product support contact your reseller For technical service contact Opticis by email techsupp opticis com or visit its website at www opticis com 1 8 Troubleshooting Maintenance Technical Support Product Specifications M5 1003 Optical KVM Extender O Compliance with DVI standard supports DVI 1 0 of DDWG using fiber optic comm
10. unication links and DDC2B O Compliance with USB 1 1 standard O Extension limit 2km 6 560feet for WUGA 1920x1200 24bit color at 60Hz refresh rate O Audio 3 5mm analog stereo audio O RS 232 D sub 9 Pin O Fiber optic Connection The transmitter and receiver boxes of M5 1003 have two 2 duplex LC receptacles connected to two 2 duplex Single Mode or Multi Mode optical patch cords O Mechanical specifications of Transmitter and Receiver boxes m Dimensions 320 x 44 X 130mm W H D m Weight 460 10 0 gram for each of Uplink and Downlink module O Environmental Specifications m Operating temperature 0 C to 50 C m Storage temperature 10 C to 85 C m Humidity 5 to 85 AC DC Power Adapter O Power Input Universal AC 85 264V 50 60Hz AC power cord with power jack O Power Output 12 V 3 0 A SMPS DC power Adapter O Cord DC Jack amp length Core is 12 V and outer cylinder is GND Length is 18 5 cm AC Cord length 1 8m Certification PSE UL cUL FCC CE TUV GS 1 9 Product Specifications Warranty Information 1 One Year Warranty Opticis warrants this Digital Video Audio and Serial I O Optical Extender to be free from defects in workmanship and materials under normal use and service for a period of one 1 year from the date of purchase from Opticis or its authorized resellers lf a product does not work as warranted during the applicable warranty period Opticis shall at its option and expe
11. will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Re orient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult a service representative for help Properly shielded and grounded cables and connectors must be used in order to comply with FCC CE emission limits Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Certification for Safety The extension system is certified pursuant to IEC60065 and its AC DC power adapter is certified by UL1310 1950 60950 for North America cUL or CSA for Canada TUV CE amp GS for EU and PSE for Japan Certification of Eye Safety This laser product is inside implemented by using 1310nm 1550nm Bi di Transceivers manufactured by Opticis Co Ltd which are all certified by CDRH FDA referred in Accession Number 0210774 as classified in Laser Class 1 11 Regulatory Statements
12. ycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product The recycling of materials will help to conserve natural resources For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product 1 10 Warranty Information FCC CE Statement for Regulation of Electro magnetic Emission This device complies with part 15 of FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 and 2 of FCC Rules EN 55022 55024 61000 3 for CE certification These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction guide may cause harmful interference to radio communications However there is no guarantee that interference
Download Pdf Manuals
Related Search