User manual - Interfocos
Contents
1. button pilot light remains burning stand by position Pressing briefly the 4 small flame button gradually lowers the flames to the low position Pressing the 4 small flame button twice automatically lowers the flames to the low position When this happens the flames will first automatically go to maximum This is indicated by LO on the display 16 Instructions for use Bellfires English e Press button N large flame to increase the flame level and to turn on the burner from the stand by position Pressing briefly the A large flame button gradually increases the flames to the high position Pressing the N large flame button twice automatically increases the flames to the high position This is indicated by HI on the display Important If you turn on the main burner by pressing the Q large flame button it must ignite within 10 seconds AN If this does not happen immediately close the gas tap and warn the fitter s Ifthe main burner ignites with a pop immediately close the gas tap and warn the fitter e Press the small flame button to lower the flames or to switch off the main burner e Then press the OFF button to switch off the appliance including the pilot light e Press the O I switch on the gas control block to the O position This conserves battery life e Ifthe appliance is not to be used for some time please close the gas supply valve in the gas pipe Important If2. for use carefully before using the appliance for the first time Keep this booklet in a safe place 2 2 BUILT IN PROTECTION OF THE APPLIANCE The appliance is fully protected by means of a thermo electric pilot light shut off in the event of a gas escape from the main burner Do not place embers vermiculite granules wood logs or pebbles against the pilot light burner Make sure that the pilot flame can burn at all times freely over the main burner Only in this way is proper ignition of the main burner ensured Ignoring these directions could lead to a dangerous situation Do not place flammable objects within 100 cm of the appliance Pay special attention to furnishings and ornaments around the fire When igniting the pilot light and burner always keep a minimum distance of 100 cm from the front of the appliance If the pilot flame goes out for any reason wait for 5 minutes before attempting to re light it It is essential that the appliance the complete concentric flue system and the outlet are cleaned and inspected annually by a recognised fitter gas specialist The safe operation of the appliance will thus remain guaranteed For this please refer to the Installation instructions Chapter 2 Maintenance that are supplied separately with each appliance The gas fire must never be used with the door open or the door glass removed gt PERE gt Instructions for use 9 Bellfires Y S gt S English Never place fla
3. the pilot flame goes out for any reason wait for 5 minutes before attempting to T re light it Faults e If the signals from the hand held transmitter do not seem to be reaching the receiver the cause may be Spent batteries replace the batteries An electronic problem press the RESET button on the receiver e If the appliance regularly switches itself off please contact your installer Replacing the batteries e The hand held transmitter receiver batteries have a service life of approx one year We recommend you use alkaline batteries Rechargeable batteries are not permitted e The batteries must be replaced whenever 1 Hand held transmitter The battery symbol indicates this in the display NN Battery fully charged H Battery empty 2 Receiver 3x short audio signal audible when the motor knob operates Instructions for use 17 Bellfires English Hand held transmitter Open the cover on the back of the transmitter Carefully remove the 9V battery and disconnect it from the contact Do not pull the wires Connect the new battery and replace in the battery compartment Close the cover Receiver Carefully pull the receiver assembly out of the compartment behind the white panel door Open the cover Remove the batteries from the battery compartment Place four new 1 5V batteries LR6 or AA type as indicated in the battery compartment The negative end of the battery must always be at the c
4. Bellfires since 1928 INSTRUCTIONS FOR USE amp MANUAL DAILY MAINTENANCE VENTO CLASSIC SMALL Gas fire with closed combustion system Bellfires wishes you many cosy evenings with your new Bellfires gas fire This document is an essential part of your gas fire Read it carefully before use of the gas fire and keep it in a safe place Serial number Production date Bellfires English BELLFIRES GAS FIRE WITH CLOSED COMBUSTION SYSTEM Vento Classic Small VCS Instructions for use 3 Bellfires English 4 Instructions for use Bellfires English CONTENTS Page 1 WARRANTY TERMS eieiaeo nn nn RENAN Tei 7 2 INSTRUGTIONS FOR USE sue dt rares cae Ale ne 9 3 USING THE APPLIANCE FOR THE FIRST TIME eee eee 20 4 DAILY MAINTENANCE 2228 eet eee UR aici 20 5 ANNUAL MAINTENANCE disons ein eke ne ecg eee 21 Instructions for use 5 Bellfires English 6 Instructions for use Bellfires English 1 WARRANTY TERMS Interfocos Warranty terms Interfocos B V guarantees the quality of the supplied Bellfires hearth and the quality of the materials used All Bellfires hearths are developed and manufactured according to the highest possible quality standards If despite all this something should prove amiss with the Bellfires hearth you have purchased Interfocos B V offers the following manufacturer s warranty Article 1 Warranty 1 1 If Interfocos B V determines that the Bellfires hearth you have pur
5. bustion chamber a similar guarantee is given until after the first burning Article 6 Liability 6 1 A claim granted by Interfocos B V under this warranty does not automatically imply that Interfocos B V also accepts liability for any possible damage The liability of Interfocos B V never extends further than that stated in these warranty conditions Any liability of Interfocos B V for consequential damage is expressly excluded 6 2 That stated in this provision is not valid if and to the extent that is derives from a mandatory provision 6 3 All agreements entered into by Interfocos B V are unless specifically stated otherwise in writing and to the extent that they are permitted based on applicable law subject to the Conditions of the Dutch Metal and Engineering Association METAALUNIEVOORWAARDEN as filed with the registrar of the Court of Rotterdam on 1 January 2008 Interfocos B V Hallenstraat 17 5531 AB Bladel The Netherlands Tel 31 497339200 Email info Bellfires com Carefully retain the instructions for use they show the serial number of the hearth You will need this if you wish to claim under the warranty 8 Instructions for use Bellfires English 2 INSTRUCTIONS FOR USE 2 1 INTRODUCTION Congratulations on your purchase of this modern Bellfires gas fire This quality product will provide you with many years of enjoyment due to the flame effect and warmth that it provides Please read the instructions
6. chased is defective as a result of a flaw in the construction or material Interfocos B V guarantees to repair or replace the hearth free of charge without charging any costs for labour or spare parts Repair or replacement of the Bellfires hearth will be undertaken by Interfocos B V or by a Bellfires dealer as designated by Interfocos B V This warranty is supplementary to the existing legal national warranty of Bellfires dealers and Interfocos B V in the country of purchase and is not intended to restrict your rights and claims based on the applicable legal provisions Article 2 Warranty conditions 2 1 Should you wish to claim under the warranty please contact your Bellfires dealer 2 2 Complaints should be reported as quickly as possible after they have manifested themselves 2 3 Complaints will only be accepted if they are reported to the Bellfires dealer together with the serial number of the Bellfires hearth which is stated on the front of the instructions for use 2 4 In addition the original receipt invoice receipt cash receipt showing the date of purchase must also be submitted 2 5 Repairs and replacements during the warranty period do not give any entitlement to an extension of the warranty period After a repair or replacement of warranty parts the warranty period shall be deemed to have started on the date of purchasing the Bellfires hearth If a certain part is eligible for the warranty and the original part is no
7. d a cowl Should the pilot light go out you must wait five 5 minutes before attempting to re ignite the fire Important Once the fire is lit it must burn at maximum for approx 10 minutes to allow the chimney to come up to temperature 2 3 2 Hand held transmitter The remote control works by radio signal The hand held transmitter is configured in the factory with a unique signal code Figure 1 Hand held transmitter Instructions for use 11 Bellfires English Set the display Connect the batteries By simultaneously pressing OFF and small flame can be switched from F and 12 hour clock to C and 24 hour clock or vice versa The display will automatically return to mode after some time but you may immediately return to mode by pressing the OFF button Set the current time By simultaneously pressing N large flame and small flame the display flashes You are in SET mode While the screen is flashing you can adjust the time Press large flame to set the hour and small flame to set the minute Wait or press OFF to return to mode Important Setting up signal code before using the appliance for the first time Before the appliance can be used the receiver must first learn the hand held transmitter s signal code Press the RESET button on the receiver and keep this pressed until 2 audio signals are heard See figure 2 Release the RESET button after the second somewhat long
8. er audio signal Press within 20 seconds the small flame button on the hand held transmitter until 2 short signals are heard The signal code has now been set up on the receiver If however a single long sound is heard this means that setting the signal code has failed or that the wiring has been connected incorrectly You only need to set up the signal code once It is not necessary when changing the batteries of the hand held transmitter or receiver Figure 2 Receiver RESET button 12 Instructions for use Bellfires English Operating possibilities It is possible to use the remote control in 3 ways to operate the appliance 1 MAN 2 Krew and D mP 3 3 You can cycle through the menu with operating possibilities by repeatedly depressing the SET button MAN D K TEMP gt TEMP gt TIMER gt MAN At the selected starting time P1 or P2 or stopping time P1 gt or P2 D is also shown Returning to is also possible by pressing the small flame or 4 large flame button MAN Manual operation Here you can turn the burner on and off and adjust the height of the flames e Press N large flame to turn on the burner and to increase the flame height e Press small flame decrease the flame height to turn the burner off The pilot light will keep burning Stand by position e The appliance will automatically revert to stand by if o the hand held transmitter is outs
9. er 3 ignition attempts close the gas tap and warn the fitter e Once the pilot light is burning the main burner must ignite within 10 seconds automatically If this does not happen immediately close the gas tap and warn the fitter s Ifthe main burner ignites with a pop immediately close the gas tap and warn the fitter Instructions for use 15 Bellfires English Connection Piezo Igniter only for MANual control ON OFF Switch Operating Knob 8 wire Receiver Jack Motor Knob in maximum position Microswitch Figure 3 Gas regulating block Operating Knob in ON position e Possible error messages 3x short audio signal audible when the motor knob operates Receiver batteries need changing soon having heard this signal the appliance can be ignited another ten times approximately 5 second unbroken tone Error For example one of the cables may not be properly connected the O I switch is not in the T position 5 short beeps Ignition of the pilot light and main burner failed Possible cause air in the pilot light pipe Important If the pilot flame goes out then wait for T at least 5 minutes before repeating the above procedure Setting the flame height extinguishing the fire e After ignition the burner automatically sets the flames to the maximum height e Press button small flame to lower the flames and to turn off the main burner Extinguishing the fire small flame
10. g periods P1 and P2 These heating periods repeat automatically every 24 hours Also see Programming the timer P1 and P2 The appliance works thermostatically at the pre set starting times P1 and P2 and the room temperature is automatically regulated to the pre set day temperature kr The appliance works thermostatically at the pre set stopping times P1 and P2 3 and the room temperature is automatically regulated to the pre set night temperature D rw In order to allow the appliance to regulate the temperature at night the night temperature D P must be set to at least 5 C If the setting is lowered to E the appliance will switch to stand by at night The appliance will automatically operate at the following day cycle N B The pre set temperature is shown on the screen every 30 seconds Setting the desired temperature Select the desired mode of operation Xue or 3 by pressing the SET button briefly e Press the SET button until the temperature indication on the display begins to flash Set the temperature with amp large flame or small flame e Wait or press the OFF button briefly to go to mode e If the temperature control in should be off lower battery consumption decrease the night temperature until G appears on the display Important Place the hand held transmitter in a place that is not A 14 influenced by direct sunlight draught heat from the appliance and other heat sou
11. gas supply valve to the fire Important If the pilot flame goes out for any reason T wait for 5 minutes before attempting to re light it Instructions for use 19 Bellfires English 3 USING THE APPLIANCE FOR THE FIRST TIME The gas fire is coated with a lacquer layer resistant to high temperature During the first hours of operation the burning in of the lacquer may result in an unpleasant smell This is harmless however Operating the gas fire at full capacity for a few hours while ventilating the room will eliminate the smell After using your gas fire for the first few times you may be aware of a light deposit on the inside off the glass This is caused by the paint curing Once your fireplace has cooled down this deposit can be removed with glass cleaner or ceramic hob cleaner 4 DAILY MAINTENANCE e Ensure that as little dust and as few particles of cigarette smoke candles and oil lamps as possible pollute the air in the room in which the appliance is used Heating of these particles by the convection system of the appliance could lead to discoloration of the walls and ceiling It is therefore very important to ensure that the room in which the appliance is located is sufficiently ventilated Regularly remove any dust deposits from behind the white panel door operating unit by means of a vacuum cleaner Important e Regularly clean the glass on the inside of the appliance with glass spray or ceramic hob cleaner A Attent
12. ide the range of the receiver for more than 6 hours o the batteries in the hand held transmitter are almost depleted o the batteries in the receiver are fully depleted The pilot light will also be turned off This also applies to the Thermostat and Timer operation e When one of the buttons on the hand held transmitter is pressed except the SET button the transmission symbol F appears on the screen The receiver confirms the transmission with an audio signal TEMP Operating day temperature thermostat Appliance is in the stand by position and the pilot light is burning Automatic temperature regulation of the pre set day temperature The room temperature is measured and compared with the pre set day temperature The flame height is automatically regulated so as to reach the pre set day temperature Also see Setting the desired temperature Instructions for use 13 Bellfires English Operating the night temperature thermostat Appliance is in the stand by position and the pilot light is burning Automatic temperature regulation of the pre set night temperature The room temperature is measured and compared with the pre set night temperature The flame height is automatically regulated so as to reach the pre set night temperature Also see Setting the desired temperature Timer operation Appliance is in the stand by position and the pilot light is burning Appliance functions automatically according to the two pre set heatin
13. ing down the recessed switch press the square piezo button several times the piezo button is alongside the O T switch to ignite the pilot light Check whether the pilot light has been lit through the glass Once the pilot light is lit the recessed switch must be kept down for a further ten seconds after which it can be released Important If the pilot flame goes out then wait for T at least 5 minutes before repeating the above procedure e Move the operating knob to the ON position Depending on the position of the motor knob the burner will either ignite or not e By turning the motor knob anti clockwise to the desired position the burner will ignite and the flame height can be controlled Important s When the main burner is switched on by turning the motor knob to the left the burner must A ignite within 10 seconds If this does not happen immediately close the gas tap and warn the fitter s If the main burner ignites with a pop immediately close the gas tap and warn the fitter Extinguishing the fire e Turn the motor knob on the gas regulating block as far as it will go in a clockwise direction The knob will audibly click The burner is now switched off The pilot light will remain lit e Press the O I switch on the gas regulating block to the O position The pilot light will be extinguished e If the gas fire is not going to be used for a long period of time it is recommended to close the
14. ion If the glass is not cleaned on time this can result in becoming dull and difficult if not impossible to clean See installation instructions for dismantling assembling the glass s Ifthe glass is broken or cracked it must be immediately replaced before operating the gas fire again Ceramic heat resistant glass may not be placed in AN the glass container but must be included in normal household waste e If anything is spilt on the fire switch it off immediately and wait for it to cool down sufficiently before cleaning Never use scouring powder aggressive cleaners or fire polish on the gas fire Use only a dry lint free cloth e Heat resistant lacquer in aerosols can be obtained from your distributor During the yearly maintenance the lacquer can be used to repair small areas of damage 20 Instructions for use Bellfires English 5 ANNUAL MAINTENANCE Instructions for use It is essential that the appliance the complete concentric flue system where possible and the outlet are cleaned and inspected annually by a recognised fitter gas specialist The safe operation of the appliance will thus remain guaranteed Please refer also to the Installation instructions that are supplied separately with each appliance 21 Bellfires 22 English Instructions for use Bellfires since 1928 Your Bellfires dealer 02 011112 331775
15. longer available Interfocos B V shall ensure that an alternative part of at least the same quality shall be provided Article 3 Warranty exclusions 3 1 The warranty on the Bellfires hearth ceases to be in effect if a itis not installed according to the supplied installation instructions and to national and or local regulations b it has been installed connected or repaired by a non Bellfires dealer Instructions for use 7 Bellfires English it has not be used or maintained according to the instructions for use it has been changed neglected or roughly treated it has been damaged as a result of external causes outside the hearth itself for example lightning strike water damage or fire 3 2 In addition the warranty lapses if the original purchase receipt shows any change deletion removal or if it is illegible Article 4 Warranty area 4 1 The warranty is only valid in those countries where Bellfires hearths are sold through an official dealer network Article 5 Warranty period 5 1 This warranty will only be granted during the warranty period 5 2 The body of the Bellfires hearth is guaranteed for a period of 10 years against construction and or material faults starting from the moment of purchase 5 3 For other parts of the Bellfires hearth a similar warranty applies from the moment of purchase for a period of one year 5 4 For user parts such as glass glass cord thermocouple and the interior of the com
16. mmable material on the ceramic log set The filling of the main burner with embers vermiculite granules wood logs or pebbles may not under any circumstances be changed or added to Do not place easily flammable materials such as nylon clothing or flammable liquids in the vicinity of the gas fire Ensure at all times that children and other people who are not aware of the operation of the gas appliance are only in the vicinity of the appliance exclusively under supervision Use a fireguard to protect the people and children mentioned above against possible burns 2 3 OPERATION REMOTE CONTROL 10 Instructions for use Bellfires English 2 3 1 General Read these instructions carefully before lighting the fire The appliance is opperated by radio remote control This comprises a hand held transmitter and a receiver The receiver is part of the gas control block assembly The receiver and the gas control block are behind the white panel door operating unit next to the appliance Press the door inwards to open this will release the catch and the door will spring out The hand held transmitter and receiver are powered by batteries Hand held transmitter 1x 9V battery Receiver 4x 1 5V battery type LR6 or AA Option 6V adapter 230 VAC Available from your fitter Note Hand held transmitter and receiver are not interchangeable with previous models The pilot light is situated in the front of the burner behin
17. ontact spring end of the compartment Close the cover and place the receiver back in its holder If the batteries are inserted incorrectly the electronics or drive may be irreparably damaged Only replace the batteries when the appliance has been completely switched off 2 3 4 Operation Hand control In an emergency it is possible to operate the appliance manually To do so the ignition piezo cable must first be removed and transferred carefully to the piezo connector on the gas control block Piezo button only for MANual control Connection Piezo Igniter only for MANual control Metallic Core for Manual Ignition recessed switch ON OFF Switch Operating Knob in Position for Manual Ignition 8 Wire Receiver Jack Motor Knob in maximum position Microswitch Figure 4 Gas regulating block Operating Knob in MAN position 18 Instructions for use Bellfires English Igniting the fire e Open the gas supply valve in the gas pipe to the fire e Switch the O I switch on the gas regulating block to the T position e Turn the motor knob on the gas regulating block completely to the right in the OFF position The switch will audibly click e Turn the operating knob on the gas control block to the MAN position A recessed switch within the knob will become visible e Press the recessed switch Use a pen or similar instrument to do this Gas will now flow to the pilot light e While hold
18. rces Instructions for use Bellfires English Programming the timer P1 and P2 Select the desired mode of operation TER by pressing the SET button briefly Press the SET button until P1x heating period 1 and the time appear in the display The time indication flashes Set the time for the beginning of the first heating period by pressing N large flame for houre and amp small flame for minute setting Press the SET button briefly P1 appears on the display Set the time for the end of the first heating period Press SET again to set the second heating period P2 heat ON and P29 heat OFF Wait a moment or press OFF to switch back to mode 2 3 3 Operation Remote Control Igniting the fire Open the gas supply valve in the gas pipe to the fire Press the O I switch on the gas control block to the T position Turn the operating knob on the gas control block to the ON position Switch the hand held transmitter to the position On the hand held transmitter press the OFF and N large flame buttons simultaneously A short tone will signal the start Release the buttons Short beeps will then follow until the pilot light and main burner are ignited Once the main burner has been ignited the flame height will automatically rise to the maximum position Important Ifthe pilot flame goes out for any reason wait for 5 minutes before attempting to re light it A N s Ifthe pilot light does not ignite aft
Download Pdf Manuals
Related Search