UPGRADE KIT USER`S MANUAL
Contents
1. 2007 All rights are strictly reserved No part of this documentation may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying or otherwise without the prior written consent of Posiflex Technologies Inc the publisher of this Slee P N 19850900010 TRADE MARKS AND SERVICE MARKS POSIFLEX is a registered trademark of Posiflex Technologies Inc an ISO 9001 and ISO 14001 certified manufacturer Other brand and product names are trademarks and registered trademarks and service marks of their respective owners ll INSTALLATION 1 HARDWARE INSTALLATION For SD 600 series ordered with the host system KS series it is installed on the system at delivery For separately ordered SD 600 series it is delivered separately from the system and needs to be fixed onto the system per following instructions before use You may find two screw holes on back of the right side of the main unit of Jiva KS series Remove these 2 screws to remove the cover for side mount upgrade kit Take out the cable inside this cover as circled in right picture and connect it to connector inside the side mount upgrade kit SD 600 as arrowed in same picture Gently arrange the excessive length of this cable back in the hole and use the 2 original screws to fit SD 600 back to the position originally occupied by the cover if the SD 600 is not installed with the iButton reader the triangle marked cables would b2. POSIFLEX SD 600 Series UPGRADE KIT USER S MANUAL Rev Original l FEATURES Upgrade kit for fan free touch terminals Jiva KS series Optional iButton Dallas key reader Options for MSR heads covering ISO 1 amp 2 all 3 tracks or JIS VII 3 tracks type MSR can read also AAMVA and CA DMV card Magnetic Stripe Reader in USB full speed HID interface Optional audio connectors if no MSR installed Total power consumption 300 mA 5V DC through proprietary USB port FCC NOTICE This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual may cause interference to radio communications It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC Rules which are designed to provide reasonable protection against interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference WARRANTY LIMITS Warranty will terminate automatically when the equipment is opened by any person other than the authorized technicians The user should consult his her dealer for the problem happened Warranty voids if the user does not follow the instructions in application of this merchandise The manufacturer is by no means responsible for an
3. e present Connection of this would not be necessary if the SD 600 contains only the iButton reader no MSR and no audio ports Please reserve the cover if there is chance to have the side mount kit removed in the future When the SD 600 is installed with iButton receptor there will be 2 additional cables marked with a triangle in the above picture coming out of the bottom side of SD 600 Connect the longer one with a RJ45 type 10 pin modular plug to one of the COM ports for iButton reader setup and data connection DON T confuse the COM ports with the LAN port in KS systems As a general tip the COM ports are in dark color without metal shield while the LAN port has bright metal shield Connect the shorter cable through a USB PS 2 conversion cable as arrowed in the left picture to one of the USB ports inside cable cover area Route the cables through the side opening of the cable cover on KS series as illustrated in the right picture and close the cable cover This paragraph of operations won t be required if iButton reader is not installed on SD 600 Page 1 2 2 DRIVER INSTALLATION 1 For iButton reader The configuration of the iButton reader can be programmed through Hyper Terminal function at the COM port that the RJ45 type cable of SD 6000 is connected to The reader can be programmed to output through the USB port connected with the conversion cable as an USB KB or through RS232 interface as the application software
4. requires Please enter the Hyper Terminal function on KS system and select the COM port Type fully capitalized SETUP and press enter key All available configuration parameters will then be presented 2 For MSR The magnetic stripe reader in SD 600 no matter how many tracks are in the reader head connects to the host through the proprietary internal USB port working as a USB KB and therefore requires no driver installation For application in OS other than Windows such as MS DOS or Linux some technical internal modifications will be required and it is most advised to specify such conditions clearly when ordering the SD 600 For application of MS DOS model please also enable the USB keyboard in system CMOS setup Refer to Operation Guide for manipulation over the reader configuration lil OPERATION GUIDE 1 iBUTTON READER Each iButton receptor is delivered with 2 iButton keys attached Each iButton key carries a unique ID Whenever the user places an iButton key to the reading area of the iButton reader the key will stick to the reader by magnetism and the unique ID will be sent to the KS system through USB or RS232 interface as preprogrammed Please approach your dealer for purchase of any additional iButton key required 2 MAGNETIC STRIPE READER For magnetic stripe card reading be sure to insert the card to the bottom with magnetic stripe facing the mark aside the slot The movement of the card can be either inse
5. rting the card from the top surface then sliding the card down out of the slot or sliding the card upward from the lower side of the slot till it reaches the top end as long as the card is a standard one A non standard card recorded without complete degaussing prior to recovery may accept only one direction in card reading The MSR in SD 600 reads an ISO or JIS magnetic stripe card without driver Yet there is a Posiflex USB MSR Manager program provided to control some parameter configuration for ISO MSR The features controllable in this program covers each track enable disable Alt Num approach for ASCII codes and Leading Stop code enable disable The function for enabling each track of course comes in effect only when the track is physically available Please find in the Product Information CD delivered with KS system the folder Drivers SD_Series USBMSR_xxx and SetUp this manager program or download the installation program from our web http www posiflex com or http www posiflex com tw 3 SOUND PORTS The audio port in KS system is arranged to have an internal audio speaker with maximum audio power of 2 W at lower left corner of the main unit but no direct access port in the main unit The external access to audio ports can be found in the side mount option kit SD 600 with a Microphone in and a stereo line out jacks at its bottom surface as circled in the right picture The internal speaker will be automatically disconnec
6. ted when a plug is inserted in the line output jack the lower one in the circle Page 2 2
7. y damage or hazard caused by improper application The hardware utility program including instructions for its use is provided AS IS without warranty of any kind Posiflex Technologies Inc further disclaims all implied warranties including without limitation any implied warranties of merchantability or of fitness for a particular purpose the entire risk arising out of the use or performance of the software and documentation remains with you ABOUT THIS MANUAL This manual is written in an attempt with full strength to assist the user to utilize the upgrade kit SD 600 for the Posiflex fan free touch terminals Jiva KS systems This series of products incorporate 2 delicately designed POS peripherals each can be used as an excellent tool to accommodate the required security specially involved in POS business kiosk and hospitality operation This manual covers the conceptual and operational aspects of these units For technical aspects involving opening of the unit or option implementation it is only available to the authorized distributors The manufacturer of the SD 600 series heartily apologizes to the user for reserving the right to change or to modify this manual without notice due to the rapid and constant progress and improvement on science and technology The user may always obtain the most up to date information through any of our web sites http www posiflex com or http www posiflex com tw Copyright Posiflex Technologies Inc
Download Pdf Manuals
Related Search