Supertramp Manual – English
Contents
1. Failure to connect these items properly may result in injury or death Care and Maintenance 1 While your product has been initially treated with UV protectant long term exposure to sunlight will damage the product Regularly apply a UV protectant to the exposed surface of the tube to ensure the life of your product We recommend using ONLY 303 UV Protectant intended for use on vinyl for this purpose Monthly application while the product is in use is required NOT DOING THIS WILL VOID THE WARRANTY 303 UV Protectant is available at most watersports dealers or online at www 303 products com 2 WARNING Certain products especially petrolium based solvents cleaners and protectants such as ArmorAll can damage the product and use of these products will void the warranty 3 WARNING Use of a high pressure washer will damage the product and void the warranty To clean use a soft bristle brush with mild soap and fresh water 303 UV Protectant contains a safe for vinyl cleaner and can be used to clean and protect the product at the same time 4 Check the inflation of your tube often Check for proper air pressure using a manometer It may appear to have lost air early in the morning but will expand once the sun warms it Maximum expansion will occur in the heat of the day Under inflation can cause excessive rubbing where the metal frame rests on the tube causing excessive wear Proper inflation is important as this will discourage marine2. 14 48 SuperTramp 17 64 Jumping Mat 1 SuperTramp M 23 104 Fastner Set Swimstep Platform 1 gt a Ee 8 bolts with Interloc Straps 2 a es Frame Sleeves 8 Repair Rit 1 Contains Owner s Manual q Patch Material i 4 Glue DJ Spring Hook Anchor Bridle 1 Allen Wrench Please Do Not Return This Product To The Store For questions regarding assembly parts or warranty contact our customer service department at 1 509 493 4938 or access product information at www aquaglide net Aquaglide Inc 1 North Shore Dr SE White Salmon WA 98672 TEL 01 509 493 4938 FAX 01 509 493 4966 www Aquaglide neit Aqua oo P L AT IN max 272kg 600lbs AQUAGLIDE INC WHITE SALMON WA U S A STANDARDS EN 15649 2012 0 083bar EN 913 2008 W A S 1 2psi PRODUCT SUPERTRAMP 14 MADE IN PR C YEAR 2013 DESIGNED IN U S A No protection against drowning Keine Schutz gegen Ertrinken Pas de protection contre la noayada No protege contra el ahogamiento Nessuna protezione contro l affogamentol Beschermt niet tegen verdrinken Only for swimmers Nur fur schwimmer Seulement pour les nageurs Solo para nadadoresi Solo per i nuotatori Alleen voor zwemmers 427 cm 168 427 cm 168 76cm 30 Supertramp 14 L W H 2012 d WARNING Prolonged exposure to salt water can damage and or shorten the expected lifetime o
3. 6 This warranty is voided if any unauthorized repair change or modification has been made to any part of the equipment Authorization for such must come in writing from Aquaglide Z The warranty for any repaired or replacement equipment is good from the date of the original purchase only 8 Any warranty claims must be accompanied by the original purchase receipt The name of the retailer and date of purchase must be clear and legible 9 There are no warranties which extend beyond the warranty specified here Returns and Service Policy Product can be returned only if a return autho Aquaglide Inc 1 North Shore Dr SE White Salmon WA 98672 TEL 509 493 4938 FAX 509 493 4966 be prepaid or it will not be accepted Upon receipt Aquaglide will make a determination within 30 days If the product is covered under warranty it will be returned to the customer at the expense of Aquaglide Inc after repairs can be made If not the customer will receive a quote for repair and or replacement as well as any necessary cleaning and shipping charges The customer will have 30 days to accept the quotation At the end of 30 days or upon refusal of the quote Aquaglide will return the product in the condition in which it was received at the customer s expense The customer agrees to authorize Aquaglide Inc to charge the customer s credit card for any costs not covered under the terms and conditions of the Aquaglide Warranty
4. clean 120 grit sand la to rough up the surface to be patched AND ALSO the back of the patch material Aquaglide Inc 1 North Shore Dr SE White Salmon WA 98672 TEL 01 509 493 4938 Repair instructions 5 Use solvent MEK or Rubbing Alcohol and a fresh cloth to clean the sanded areas removing all debris 6 Dry fit the patch again and use china marker provided to carefully outline where the patch will be located 7 Next use the glue provided Use a disposable chip brush to spread glue if needed Try to work neatly and quickly a Using disposable brush apply a thin even cil of glue to the repair area making sure to cover the area completely Stay INSIDE the china marker outline b Using disposable brush apply a thin even layer of glue to the to the back of the patch making sure to cover the area completely c Allow glue to cure for approximately 60 seconds d Starting at one corner carefully align the patch over the repair area using the china marker outline as a guide Once the 2 surfaces touch the bond will be immediate so take care e Starting at one corner and working outward carefully apply the patch to the repair area using very firm pressure f Rub the entire patch area and the edges of the patch using very firm pres sure g Allow to cure for at least 24 hours before inflating www Aquaglide net FAX 01 509 493 4966 NOTICE Release of Liability Claim Waiver and Assumption o
5. electrical outlet or extension cord 2 Unroll and place the PVC tube on the ground and locate the valve Remove valve cover and push valve plunger in Twist the valve stem 90 degrees to open or close the 1 Way valve feature Figure 1a a F N amie SED o i Del Rda a x i ol Vs Z OF DO VP a P al n ls L d P AS 3 Using a high output inflator deflator place the inflation hose with proper adaptor into the valve Inflate until tube is firm and tight with the following pressures Supertramp 14 1 2 psi 0 083 bar Supertramp 17 0 8 psi 0 055 bar Supertramp 23 0 8 psi 0 055 bar Check for proper air pressure using a manometer Inflation times can vary by inflator but the tube should be firm and tight when completely inflated In hot weather be sure to leave room for air expansion DO NOT OVER FILL After inflation twist valve stem to prevent passage Replace cover Warning Do not use an air compressor to inflate tube Air compressors are designed for high pressure inflation and can cause tube to burst if over inflated The inflator deflator described above cannot over inflate the tube 4 IMPORTANT Once the tube is inflated locate the Anchor Bridle and lay out 1 anchor bridle webbing strap at EVERY OTHER CORNER marked in Fig 1 as items A D As you assemble frame pieces in the following instruction you will slide the anchor bridle onto the frame at these locations 5 Locate the 8 steel frame p
6. rocks or stumps 3 Keep a safe distance from docks boats boat lifts and any other structures DO NOT tie the SuperTramp to a dock 4 Anchors and anchor line are sold separately from the SuperTramp We recommend at least 150 Ibs of weight for the 14 SuperTramp Ground screws or heavier anchors 300 Ibs or more should be used with 17 and 23 trampolines or on large or windy bodies of water 9 Attach anchor line securely to the anchor Use a buoy tied to the other end of the rope to easily locate your anchor 6 When the SuperTramp is in place remove the buoy and tie the anchor line to the swivel hook on the underside of the trampoline Allow AT LEAST several feet of slack in the line before securely connecting the anchor line at the swivel This will allow the tramp movement in wind or waves without displacing your anchor 7 If strong winds or storms are expected it is best to remove the SuperTramp from the water and deflate it You can also move it closer to shore and secure it with lines Operation 1 This item is a water trampoline Users bounce near the center of the item This item must be used with at least one Aquaglide Platinum boarding platform 2 When connecting multiple items use only Aquaglide Interloc straps and connecting rings according to the Interloc Strap instructions provided Make sure that the connection is tight and that there is NO GAP greater than 25mm 3 4 between items IMPORTANT
7. tear including but not limited to punctures advance The RA number must be on the outside ship to the original purchaser for the lifetime d agging the product over the ground damage of the package or it will not be accepted at our of the product This warranty is subject to due to excessive sun exposure or seam failure warehouse Freight on the returned product must the following limitations 1 Warranty is valid only with dated proof of pur chase in the form of the original invoice 2 Warranty is valid only when the product is used for normal recreational activities and does not cover use in schools or rental operations Warranty term for commercial use is 1 year 3 Aquaglide will make the final warranty determi nation which may require inspection and or photos of the product which clearly show defect s We require the above be sent to another location of our choice freight prepaid or by email to warranty aquaglide net 4 If a product is deemed to be defective by Aqua glide the warranty covers the repair or replacement of the defective product only Aquaglide will not be responsible for any costs losses or damages incurred as a result of loss of use of product o This warranty does not cover damage caused due to overinflation in the sun damage caused by improper handling and storage damage caused by use in waves or shore break and damage caused by anything other than defects in materials and workmanship
8. AMAGE CAUSED BY EXPOSURE TO SALT WATER IS NOT COVERED BY WARRANTY Aquaglide Inc 1 North Shore Dr SE White Salmon WA 98672 USA Compliant with DIN EN 15649 Watersports Safety Code Watersports are fun and challenging but involve inherent risks of injury or death To increase your enjoyment of the sport and to reduce your risks use common sense and follow these rules Before you start e Familiarize yourself with all applicable federal state and local laws the risks inherent in the sport and the proper use of the equipment e Know the waterways Use caution and common sense Do not use in recreational swimming pools or within 4 5m 15ft of boats docks or other hard obstructions Do not attempt or allow somersaults Landing on the head or neck can cause serious injury paralysis or death even when landing in the middle of the bounce surface Do not dive head first or swim under your SuperTramp Never use at night or in low light conditions Never use in poor weather conditions with excessive wind waves or lightning Do not use on dry land Do not use without proper anchoring Do not exceed maximum weight or maximum number of users for your particular SuperTramp Always maintain water depth of at least 8ft 2 44 m Take extreme care when swimming between the shore and the product Be cautious of any boat traffic or other obstructions Ensure all users are capable swimmers and are not excess
9. Owners Manual super alii Aqua oo Pe L A T REA LS en AQUAPARK SYSTEM PLAT Va 14 17 23 Owner s Manual A Stop Read this manual carefully before using this product Aqua Super IND It is the owner s responsibility to read the owner s manual Manual covers the Max Max Max and instruct all users in the safe operation of these products By inflat following products Jumpers Users Capacity ing these products you hereby agree to the Release of Liability Claim Waiver and Assumption of Risk Agreement in this manual Please read this manual prior to inflating and using these products and keep for Sils Li Si DI Three P 600 Ibs 272 kg future reference As with any action sport recklessness inexperience SuperTramp 17 ree our 800 Ibs 363 ka misuse or neglect of the equipment may result in serious injury SuperTramp 23 Three 3 Five 5 1000 Ibs 454 kg janet Contents Per Product No Special Tools Required To Assemble Your New SuperTramp SuperTramp 1 Inflatable Tube 1 Jumping Mat 1 Spring Pad Cover 8 Galvanized Frame Bars 8 Frame Sleeves 1 Fastener Set 1 Swimstep Access Platform 2 Interloc Straps 1 Anchor Bridle 1 Allen Wrench 1 Repair Kit 48 Springs SuperTramp 14 64 Springs SuperTramp 17 104 Springs SuperTramp 23 Galvanized Frame Bars 8 Inflatable tube 1 Spring Pad Cover 1 Springs per size SuperTramp
10. S ENCOUNTERED BY USERS THE CODE DOES NOT PURPORT TO COVER ALL INSTANCES OF RISK OR DANGER PLEASE USE COMMON SENSE AND GOOD JUDGMENT Please contact us if you have any questions on the proper selection function or safe use of this product A WARNING Watersports can be safe and fun for all levels of enthusiasts The Operator s Manual is presented to enhance USE OF THIS PRODUCT AND PARTICIPATION IN WATERSPORTS your enjoyment of the sport It is intended to alert you to some of the potentially dangerous conditions that INVOLVES INHERENT RISKS OF INJURY OR DEATH can arise in all watersports It is the owner s responsibility to read the owner s manual and instruct all users in the safe operation of these products By inflating these products you hereby agree to the Release of e Liability Claim Waiver and Assumption of Risk Agreement in the Owner s Manual This product should never be used by children except under adult supervision Not intended for use by children under 5 years of age To reduce the risk of injury or death follow these guidelines This product is not a personal flotation device eo e Carefully read the product Owner s Manual and follow the instructions Always wear a floatation vest PFD as required by the authorities in area of use Take all reasonable precautions in the use and operation of your trampoline and or aquapark Never place wrists or feet through handles under spring pad or frame e Teach anyone using your t
11. Serial Number All Aquaglide Platinum products are marked with a serial number near the main inflation valve 1 The serial number may be stamped into the PVC directly around the valve or it may be visible on a welded plate near the valve Please include this number when you contact Aquaglide or your dealer with any warranty claim www Aquaglide net
12. animals from chewing and prevent damage from wear Storage 1 Before storing place the SuperTramp on a clean level area Clean with mild soap and water and allow to dry completely Apply 303 Protectant to the surface of the tube and spring pad cover before deflating 2 Remove the spring pad cover springs and all hardware and store in a sealed water proof container i e a plastic covered box or bin 3 Remove ALL of the air from the tube using the deflation end of the high output inflator deflator 4 Fold the deflated tube in thirds then roll loosely 9 Store the SuperTramp out of direct sunlight and protected from the environment in a clean dry location It is best to store inside a container with moth balls to prevent damage from rodents NEVER store uncovered in a damp location or on a concrete surface NEVER store at temperatures below 40 degrees F Aquaglide Inc 1 North Shore Dr SE White Salmon WA 98672 TEL 01 509 493 4938 FAX 01 509 493 4006 VV Aquaglide net Aqua oo PLAT IN Om WORK SPACE AND TOOLS 1 Take care to position yourself in a clean dry area with ae ventila tion For proper curing of adhesives temperature should remain above 10 C 50 F In most cases you will need enough room to inflate the product 2 Repair Kit Contents PVC Patch material PVC Glue Instructions 3 Additional items that MAY be needed Air pump Sharp scissors and or razor knife Dish washing liquid water smal
13. ep access platform and connect it to the SuperTramp BEFORE INFLATING the platform using the attached Interloc straps The access platform connects on the side of the trampoline where the warnings are located Find the D rings on the tube near the water line If there are more than 2 rings use the rings indicated in Fig 9 below Take the 2 Interloc straps and connect the access platform to the tube as shown in Fig 9a Secure the straps according to the Interloc instructions shown below Once the straps are connected inflate the boarding platform until it is firm as shown in figure 9c This will tighten the platform to the side of the SuperTramp Be careful not to over inflate the access platform Figure 9 Figure 9a Figure 9c www Aquagiide ne Swimstep boarding platform Interloc Strap Assembly Instructions Interloc Strap Assembly Interloc straps should already be attached to the boarding platform If not thread one end through the loop on the end of the strap and cinch tightly 1 Thread the end of the Interloc strap through the two D Rings on the SuperTramp then back through a single ring 1 2 Pull all the webbing through the rings until the white arrow of the Interloc logo stops at the D ring below Cinch until it is tight 2 4 J 3 Pass the end of the webbing back through the open area of the two D Rings on top as shown 3 4 Now bring the webbi
14. f this product The marine environment includes many damaging elements including corrosion abrasion and damage from marine life such as barnacles Regular cleaning and rinsing with fresh water can reduce these risks A PVC safe antifouling paint should be used to help protect this product against marine growth DAMAGE CAUSED BY EXPOSURE TO SALT WATER IS NOT COVERED BY WARRANTY N N o co o i um o E A h SL vn Aquaglide Inc 1 North Shore Dr SE Compliant vvith DIN EN 15649 Aqua oo P L AT IN max 363kg 8001bs AQUAGLIDE INC WHITE SALMON WA U S A STANDARDS EN 15649 2012 0 055bar EN 913 2008 W A S 0 8psi PRODUCT SUPERTRAMP 17 MADE IN PR C YEAR 2013 DESIGNED IN U S A No protection against drowning Keine Schutz gegen Ertrinken Pas de protection contre la noayada No protege contra el ahogamiento Nessuna protezione contro l affogamentol Beschermt niet tegen verdrinken Only for swimmers Nur fur schwimmer Seulement pour les nageurs S lo para nadadores Solo per i nuotatori Alleen voor zwemmers 518 cm 204 518 cm 204 91cm 36 Supertramp 17 L W H Quagrine 2012 d WARNING Prolonged exposure to salt water can damage and or shorten the expected lifetime of this product The marine environment includes many damaging elements including corrosion abrasion and damage from marine life such as bar
15. f Risk Agreement By opening and assembling this product you are agreeing 1 to be bound to the terms set forth below and 2 to require anyone using this product to be bound by such terms If you are unwilling to be bound by these terms return this product before use for a full refund ASSUMPTION OF RISK Use of this product and any of its components involves certain inherent risks dangers and hazards which can result in serious personal injury and death In using the product you freely agree to assume and accept any and all known and unknown risks of injury while using this equipment The risks inherent in the sport can be greatly reduced by abiding by the Warning Guidelines listed in this Owner s Manual and by using common sense RELEASE AND WAIVER OF CLAIMS AGREEMENT In consideration of the sale of the product to you you hereby agree to the fullest extent permitted by law as follows TO WAIVE ANY AND ALL CLAIMS that you have or may in the future have against North Sports Inc and Aquaglide Inc its distributors and dealers resulting from use of this product and any of its components TO RELEASE North Sports Inc and Aquaglide Inc from any and all liability for any loss damage injury or expense that you or any users of this product may sufer or that your next of kin may suffer as a result of the use of this product due to any cause whatsoever including negligence or breach of contract on the part of North Sports Inc and Aquagl
16. ide Inc in the design or manufacture of this product and any of its components ARBITRATION In further consideration of the sale to you of this product and any of its components you hereby agree to submit to binding arbitration any and all claims which you believe you may have against North Sports Inc and Aquaglide Inc arising from the use of any North Sports Inc and Aquaglide Inc equipment or products The arbitration shall be pursuant to the rules of the American Arbitration Association Arbitration shall be commenced within 1 year from the date on which any alleged claim first arose Further the arbitration shall be held in White Salmon Washington unless otherwise mutually agreed to by all parties The submission to the American Arbitration Association shall be unlimited and the arbitration award may be enforced by any Court of competent jurisdiction BINDING EFFECT OF AGREEMENT In the event of your death or incapacity this Agreement shall be effective and binding upon your heirs next of kin executors administrators assigns and representatives ENTIRE AGREEMENT in entering into this Agreement you are not relying upon any oral or written representations other than what is set forth in this agreement and the North Sports Inc and Aquaglide Inc Owner s Manual Aquaglide Inc warrants this Supertramp to PY misuse abuse neglect or normal wear and rization number RA is given by Aquaglide in be free of defects in material or workman
17. ieces protective sleeves and fastening hardware Slide the protective sleeves over each bar before assembling as shown in Fig 1 Use the straps to hold the frame in place Slide each bar into the bar holders and connect the frame bars at the point of each octagonal corner as shown in Fig 3 Fig 4 Do this by sliding the smaller end of bar into the larger end and secure with fastener set using the included Allen wrench NOTE For long term use seal fastener bolt threads with LocTite or similar Anti seize lubricant Make sure the spring slots are facing UPWARD and the protective sleeves are on each bar before bolting them together Spring holes face UP sleeve slides up to cover VA frame bolt e Pele a sleeve at each corner use straps to secure frame Aquaglide Inc 1 North Shore Dr SE White Salmon WA 98672 TEL 01 509 493 4938 FAX 01 509 493 4966 www Aquaglide net Bridle loop Figure 5a o gt Figure 5b Place anchor bridle cinch loop over frame at every other corner positions A D in Fig 1 Dl a 6 IMPORTANT Make sure to incorporate anchor bridle into frame as frame is assembled Pull the anchor bridle webbing through the bridle loop to make a cinch loop as shown in Fig 5a 5b As frame is assembled slide the anchor bridle onto the frame at every other corner as shown in Fig 6 7 Two people are recommended for attaching the springs Place black jump mat with warning label facing up
18. ively fatigued Do not allow anyone to attempt to swim to or from the product that are not physically able to do so Always ensure that the swimming area around the trampoline is free of submerged logs rocks and sandbars Ask about the local water conditions before use Only allow use of the product with proper supervision Secure the product when not in use to prevent access by any other users Do not jump or dive from this item Do not jump onto this item from any other item Do not use in water where there are sharks or other animals that could pose a threat to humans e If product is used indoors always ensure adequate ceiling height overhead e Always remove personal items such as rings watches or other sharp objects before use Your Equipment e Check all equipment prior to use Inspect your SuperTramp for missing defective or worn parts Never use your SuperTramp without the Spring Pad Cover in place and securely fastened to the frame e Always check for proper inflation before each use Temperature and environmental changes can cause changes in tube pressure Using the product over or under inflated is dangerous and can cause damage to the product voiding the warranty Always check security of the anchor and all attachments before each use Always wear a floatation vest PFD as required by the authorities in area of use THE WARNINGS AND PRACTICES SET FORTH ABOVE IN THE WATERSPORTS SAFETY CODE REPRESENT SOME COMMON RISK
19. l bowl or id bottle 120 Grit sandpaper solvent such as MEK Methyl Ethy Ketone or Rubbing alcohol china marker small chip brush or disposable paint brush LOCATE LEAKIS 1 ue is a problem with air leaks you will need to locate the leak s irst 2 Inflate your Aquaglide Platinum product fully Some small leaks can close themselves at lower air pressures so it is best to maintain full pressure by re inflating periodically while checking for leaks 3 Use a soapy water solution 50 50 dish soap amp water and a cloth to check for leaks Work slowly around the product Re or swabbing on soapy water solution Look for growing bubbles which indicate a leak 4 u leak is confirmed dry the area well mark it and prepare to patch PATCHING Reinforced PVC Patch with high grade adhesive IMPORTANT leaks must be patched with the item completely deflated and patches must be allowed to cure for 24 hours 1 DEFLATE your Aquaglide Platinum product completely 2 a cut PVC patch material to size using sharp scissors or razor nife a Patch should be least 3 5cm 1 2 larger than hole IN ALL DIRECTIONS around any air leak This means a minimum patch size of 5cm x 5cm 2 x 2 for a pinhole leak The larger the better b Square patches with rounded corners are usually best as this reduces the risk of peeling 3 Dry fit the patch over the area to be repaired to ensure good fit and coverage 4 Use a
20. nacles Regular cleaning and rinsing with fresh water can reduce these risks A PVC safe antifouling paint should Aquaglide Inc 1 North Shore Dr SE White Salmon WA 98672 USA Compliant with DIN EN 15649 be used to help protect this product against marine growth DAMAGE CAUSED BY EXPOSURE TO SALT WATER IS NOT COVERED BY WARRANTY Aqua vo P L AT IN Super iii AQUAGLIDE INC WHITE SALMON WA U S A STANDARDS EN 15649 2012 0 055bar EN 913 2008 W A S 0 8psi PRODUCT SUPERTRAMP 23 MADE IN PR C YEAR 2013 DESIGNED IN U S A No protection against drowning Keine Schutz gegen Ertrinken Pas de protection contre la noayada No protege contra el ahogamiento Nessuna protezione contro l affogamentol Beschermt niet tegen verdrinken Only for swimmers Nur fur schwimmer Seulement pour les nageurs Solo para nadadores Solo per i nuotatori Alleen voor zwemmers 686 cm 270 686 cm 270 95 cm 38 Supertramp 23 L W H Q 9 amp N q 2012 d WARNING Prolonged exposure to salt water can damage and or shorten the expected lifetime of this product The marine environment includes many damaging elements including corrosion abrasion and damage from marine life such as barnacles Regular cleaning and rinsing with fresh water can reduce these risks A PVC safe antifouling paint should be used to help protect this product against marine growth D
21. ng through the opening in the single D Ring on the platform as shown 4a 9 Fold the strap over onto the velcro 4b and Place the other Velcro tab in place to lock the strap 4c Aquaglide Inc 1 North Shore Dr SE White Salmon WA 98672 TEL 01 509 493 4938 FAX 01 509 493 4966 WWW Aquaglide net 11 Congratulations You are now ready to place your SuperTramp in the water Make sure to have at least 3 4 people evenly spaced around the trampoline to help carry the SuperTramp NEVER DRAG YOUR SUPERTRAMP YOU MUST LIFT AND SET TO AVOID ANY ACCIDENTAL TEARING ON SHARP OBJECTS Anchoring IMPORTANT Proper anchoring is essential to the safety and performance of your product Due to the wide variety of conditions we advise using a professional skilled in mooring and anchoring and experienced with local conditions If improperly anchored the product can move and or float away Aquaglide Inc is not responsible for any damage injuries or losses due to improper anchoring Here are some general guidelines for anchoring your product These guidelines are not intended to replace the need for professional installation 1 Choose your location for your SuperTramp Place the trampoline in at least 8 ft of water depth and in an area protected from the wind and boat traffic Review any rules and restrictions with your local authorities 2 Carefully check area under the trampoline for sharp or dangerous objects i e
22. rampoline and or aquapark about safe guidelines prior to use Never use the trampoline without the spring pad cover secured Know your own limits Stop when you are tired Act responsibly Be in good physical A condition and be cautious in your use of this or any other water sports product Do not use in shallow water less than 8ft 2 44m deep e Periodically check mooring bridles and or lines to ensure safety Replace any portion of Do not use within 15ft 4 57m of shore docks pilings or other hard objects mooring and or connection system that shows signs of wear Never swim under this product e Do not add any hardware or attachments not otherwise supplied by the manufacturer PO Not EMP Or dive fom ipa THE WARNINGS AND PRACTICES SET FORTH ABOVE REPRESENT SOME COMMON RISKS I Do not exceed the manufacturer s recommended number of users for ENCOUNTERED BY USERS AND DOES NOT PURPORT TO COVER ALL INSTANCES OF RISK OR DANGER this particular product PLEASE USE COMMON SENSE AND GOOD JUDGMENT Do not use while under the influence of alcohol or drugs Read Operator s Manual before use Please contact the dealer or manufacturer of this product if you have any questions about proper selection function or safe use of this product Made in China p Made in China Aquagide Inc 1 North Shore Dr SE White Salmon WA 98672 TEL 01 509 493 4938 FAX 01 509 493 4966 MrWW Aguaglide net Assembly 1 Locate a flat dry area with access to
23. ward in the center of the SuperTramp Work across from each other placing a spring from the metal triangle on the jump mat first and then pulling toward the corresponding slot in the frame bar Always start at the middle triangle and stretch the spring to the corresponding middle slot in the frame bar USE SPRING HOOK provided AND OR GLOVES TO PROTECT YOUR HANDS FROM PINCHING DURING ASSEMBLY 8 Once you have placed the first two springs opposite each other consider this position 1 and 2 as shown in Fig 7 Now locate position 3 and 4 and repeat the same instructions The jump mat is now supported by the 4 springs Again working across from each other place the remaining springs into the triangles on the jump mat and pull them into the slots on the frame bar until all springs are connected Aquaglide Inc 1 North Shore Dr SE White Salmon WA 98672 TEL 01 509 493 4938 FAX 01 509 493 4966 MriWww Aguaglide net 9 Next unfold the white spring pad cover and place it over the springs and frame until they are all covered Line up the spring pad cover to match the octagonal shape of the tube and frame as shown in Fig 8 Reach underneath the spring pad cover in all 8 corners Feed the webbing strap under the bottom of the frame bar then through the buckle as shown in Fig 8a Secure the spring pad cover to the frame in each corner Cinch each strap to ensure a snug fit Figure 8 cinch Ny gt 5 Figure 8a 10 Roll out your Swimst
Download Pdf Manuals
Related Search