Home

Z1 PLUS DMX-512 LED CONTROLLER User Manual

1. 8 poles plug in screw connector LEDs cabling connection can be done with a standard UTP TIA EIA 568 A category 3 cable The maximum distance between power supply and the last LED lamp in the line should not exceed 100 meters IMPORTANT NEVER USE BOTH RJ45 AND 8 POLES RGBA OUTPUTS AT THE SAME TIME DOING SO YOU CAN SERIOUSLY DAMAGE THE POWER SUPPLY 5 Z1 PLUS LED Controller DMX SIGNAL CONNECTION The unit operates using a digital DMX 512 signal Connection between the controller and the unit or between units must be carried out using a two pair screened 0 5 mm cable and a CANNON XLR 5 poles connector Ensure that the conductors do not touch each other Do not connect the cable ground to the XLR chassis The plug housing must be isolated Connect the mixer signal to the DMX IN projector plug and connect it to the next projector by connecting the DMX OUT plug on the first unit to the DMX IN plug of the second one In this way all the projectors are cascade connected CONTROLLER STANDARD DM X 512 1 1 GND 2 DATA 3 DATA CN 3 P S If the display showing the DMX address flashes then one of the following errors has occurred DMX signal not present DMX reception problem For Installations where long distance DMX cable connections are needed we suggest to use a DMX terminator The DMX terminator is a male XLR 3 5 pins connector with a 120 ohm resistor Betw
2. 0 255 Proportionalcolour 29 Z1 PLUS LED Controller DMX PROTOCOL Z1 RGBA 4 CHANNELS LED OUTPUT 10 CHANNELS MODE Default 1 SHUTTER 2 DIMMER 3 RED 4 GREEN 5 BLUE 6 AMBER 7 WHITE Pre programmed whites at different colour temperatures 8 CTC 9 COLOURS MACRO 10 FUNCTIONS si Parameter SHUTTER Move DAMA mes range Mode Option Function Value E grees Black out AR Open 20 29 24 po Black out BA Strobe at variable speed from slow to fast 3700ms 20ms 120 149 Pulse open at variable speed from slow to fast 42 6s 100ms 150 1799 ss Pulse close at variable speed from slow to fast 42 6s 100ms 180 204 192 Random Strobe Master and RGB active 205 229 218 Random Strobe Full 230 234 Red Yellow Cyan and Blue colour effects at variable speed 235 255 245 Open DMX CHANNEL Parameter DIMMER ES Move DAMA renge range Mode Option Function Value E es A 0 255 Proportional dimmer DMX CHANNEL Parameter RED BE Move DAMA range range Mode Option Function Value AA grees 0 255 Proportionalcolour 30 Z1 PLUS LED Controller DMX CHANNEL ES Parameter GREEN NS Move DID renge range Mode Option Function Value SE Ceres 0 255 Proportionalcolour DMX CHANNEL Parameter BLUE as Move DMX range range Mode Option Function Value A eee 0255 Proportionalcolour DMX CHANNEL ue JE Parameter AMBER Move AMIR range Mode Option
3. 8 Projector 1 A001 DTS Wall mounted DMX controller 0514L007 assign 8 DMX Projector 2 A009 channels per unit also if some channels are not used Projector 3 A017 aes A projector6 A041 If you want to use the Z1 PLUS RGB in 9 channels mode select the 9 CH mode from the MODE menu and set the following addresses on the mixer Projector 1 A001 Projector 2 A010 If you want to select the next projector just add 9 Projector 3 A019 mon A projector 6 A046 If you want to use the Z1 PLUS RGBA in 10 channels mode select the 10 CH mode from the MODE menu and set the following addresses on the mixer Projector 1 A001 Projector 2 A011 If you want to select the next projector just add 10 Projector 3 A021 oie A projector 6 A051 Selelcting the DMX address 1 Press the UP DOWN key until you reach the required DMX address The numbers on the display will start to flash but the new DMX address hasn t yet been set 2 Press ENTER to confirm your selection The numbers on the display will stop flashing and the projector is now controlled by the new DMX address TIPS if you keep pushed the UP or DOWN keys the channels are calculated more quickly and you get a faster selection 7 Z1 PLUS LED Controller DISPLAY FUNCTIONS Z1 RGB Rift DISPLAY FUNCTIONS The Z1 PLUS display panel shows all the available functions Using these functions it is possible to change some of the parameters and add some functions
4. Macro 10 165179 Macro 1 180 194 Macro 12 195 209 Mao 18 210 225 Macro 4 226 239 Mater 1 240255 o gt Macrot 6 O 32 Z1 PLUS LED Controller DMX CHANNEL 9 Parameter COLOUR MACROS F ISS NAJE IS SIS EHLE PLEASE CHECK PAGE 12 Move degrees Aa No Function BRA Macrod BY Macro 2 _ 8 Macro amp 3946 pop Macro 7 TE Macros amp OGS 55620 Maro 63 700 Macro Bop pp Macros o 79 86 pop Mae 8794 Y Mao 10 95102 pp Mao 1 1030 pop Maori camas op Macrold amp 196 Macro 4 127434 Mao O 135 142 Macro 16 143150 Rainbow Speed 1 1 Sec 151 158 Rainbow Speed 2 5 Sec Casas o Rainbow Speed 3 10 Sec 167174 __ Rainbow Speed 4 20 Sec 175 182 __ Rainbow Speed 5 30 Sec 183 190 Rainbow Speed 6 60 Sec 191 198 Rainbow Speed 7 120 See 199206 Rainbow Speed 8 180 Sec 207214 Random Speed 1 0 5 sec _ 21522 Random Speed 2 1 Sec __ 223 230 RandomSpeed3 2See 231238 RandomSpeed4 SSec 1239246 Random Speed 5 10 Sec __ 247255 __ Random Speed 6 30 Sec _ Parameter FUNCTIONS Recall Create and Store the Custom white Move DMX range range Mode Option Function Value A degrees Os Custom White Recall Enable CH 7 for Custom white Recall 80 160 Custom White Create Enable CH 7 for C
5. S Illuminazione srl ITALY re Haning Company attp www dts lighting it P iii Made in Italy 2 Z1 PLUS LED Controller Le informazioni contenute in questo documento sono state attentamente redatte e controllate Tuttavia non assunta alcuna responsabilit per eventuali inesattezze Tutti i diritti sono riservati e questo documento non pu essere copiato fotocopiato riprodotto per intero o in parte senza previo consenso scritto della D T S DTS si riserva il diritto di apportare senza preavviso cambiamenti e modifiche estetiche funzionali o di design a ciascun proprio prodotto D T S non assume alcuna responsabilit sull uso o sull applicazione dei prodotti o dei circuiti descritti The information contained in this publication has been carefully prepared and checked However no responsibility will be taken for any errors All rights are reserved and this document cannot be copied photocopied or reproduced in part or completely without prior written consent from D T S D T S reserves the right to make any aesthetic functional or design modifications to any of its products without prior notice D T S assumes no responsibility for the use or application of the products or circuits described herein Les informations contenues dans le pr sent manuel ont t r dig es et contr l es avec le plus grand soin Nous d clinons toutefois toute responsabilit en cas d ventuelles inexactitudes Tous droits r serv s Ce docum
6. in AUTOMATIC MODE is active for all the programs SHUTTER function in AUTOMATIC MODE is active only for CU01 CU16 and Wh01 Wh16 macros ChPr MASTER SLAVE The first unit that will function as a Master must be set to Automatic mode AUTO the other units must be set to Slave mode SLAV selectable through the menu In this way all the Slave units will be synchronised with the master and running their own ChPr game On the master unit it is possible to vary the Speed time SPEE for the colour changhing and the Wait time UAIt between the steps Speed time and Wait time on the Master have priority on the slave units NB It is possible to run GA Pr on the other units even though these do not have GA Pr programmed You can do this by setting the units to 9 ch DMX MODE for Z1 PLUS RGB or 10 channels DMX mode for Z1 PLUS RGBA and selecting DMX address A001 18 Z1 PLUS LED Controller Rec mode It is possible to program your own game on the Z1 PLUS unit that will then run it in AUTO mode ChPr Each unit can have its own programmed game In REC mode the unit must be set to 9 channels mode for Z1 PLUS RGB and 10 channels mode for Z1 PLUS RGBA To program the ChPr by using a DMX controller you need 3 more channels in addition to the 9 10 channels necessary to control the unit So that in RECORDER mode via DMX the unit will need 12 13 DMX channels to be correctly programmed The three new DMX channels are Z1 PLUS IN RGB MODE 3 CHAN
7. typical IP protection grade IP 20 Output Power Output Range 6 100W per output 1 5 25W per channel Output Current 350 mA 100 per channel 500mA 100 per channel in BOOST Mode Output Voltage Vout 48V Max Load output 15 x MR16 RGB LED lamp or 15 x FOCUS RGB LED projector or 5 x MR16 full color LED lamp or 5 x FOCUS full color LED projector or 1 x HELIOS full color LED projector or 1 x FOS RGBA led bar Min Load output 1 x MR16 RGB LED lamp Control Input Control Signal DMX 512 Dimming System Constant Current PWM Address Range DMX 512 channels addressable by display APPLICATIONS Cinemas Restaurants and pubs Discoteques Architectural Interior and Exterior 4 Z1 PLUS LED Controller INPUT OUTPUT CONNECTIONS DMX IN OUT connectors STANDARD DM X 512 CONTROLLER Display OFP Digital Function Panel Mains 90 260 Vac 50 60 HZ RGBA outputs 8 pin Female RJ45 Infrared sensor input connector Pin 1 RED Pin 2 RED Pin 3 GREEN JL Pin 4 GREEN SE Pin 5 BLUE Con Pin 6 BLUE 8 1 Pin 7 AMBER Pin 8 AMBER 8 pin Female RJ45 RGBA outputs 8 poles plug in screw connector Pin 1 RED Pin 2 RED Pin 3 GREEN ms BLuE DU DOOSOS Pin 6 BLUE Pin 7 AMBER 1 PIN 8 Pin 8 AMBER
8. 1 Shutter Shutter level is active only for CU01 CU16 and Wh01 Wh16 macros ESC Esc from Automatic Mode Menu ENTER IPAS ENTER ua Up Down ENTER oa Up Down n 00 10 ENTER ENTER Up Down Es gt gt ENTER Up Down ENTER IS Ss Down Es Up Down e ENTER R Be AS Lc ECS ICHE REC MODE In DMX Recorder Mode it is possible to create and store the scenes of the ChPr by using an external DMX controller The unit must be set to 9 channels MODE 10 Z1 PLUS LED Controller DMX Recorder Mode For the programming of ChPr by using a DMX controller besides the 9 channels necessary to control the unit a further 3 DMX channels are needed So that in RECORDER mode via DMX the unit will need 12 channels to be correctly programmed The three new DMX channels are DMX channel 10 SCENES channel From 0 10 no function r001 From 11 255 are displayed the programmable scenes max 16 scenes from M001 to M0016 DMX channel 11 EDIT channel From 0 19 no function From 20 234 the unit runs the configuration given by the received input DMX values With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record the selected scene From 235 255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene With the channel REC it is possible to record the selected scene as last scene DM
9. AMBER RGBA WHITE IMPORTANT The maximum number of FOS 100 connectable to the Z1 Plus Power supply is 1 pcs The Maximum distance between the Z1 PLUS and FOS 100 unit should not exceed 100 meters NEVER CONNECT NOR DISCONNECT A LED UNIT WHEN THE POWER SUPPLY IS TURNED ON NEVER USE BOTH RJ45 AND 8 POLES SCREW CONNECTOR OUTPUTS AT THE SAME TIME 44 Z1 PLUS LED Controller D T S INFRARED 0749050 REMOTE SENSOR CODE 03 LA 016 __ a ur ra i no DVNWODONES i PIN S 8 poles plug in screw connector LEDS OUTPUT FOS 33 LEDS CABLE PINOUT 1 RED FC RGBA WHITE 2 RED FC RGBA WHITE 3 GREEN FC RGBA WHITE 4 GREEN FC RGBA WHITE 5 BLUE FC RGBA WHITE 6 BLUE FC RGBA WHITE 7 AMBER RGBA WHITE 8 AMBER RGBA WHITE IMPORTANT The maximum number of FOS 33 Led projectors connectable to the Z1 power supply is 3 pcs The Maximum distance between the Z1 PLUS and the last FOS 33 in the line should not exceed 100 meters NEVER CONNECT NOR DISCONNECT A LED UNIT WHEN THE POWER SUPPLY IS TURNED ON NEVER USE BOTH RJ45 AND 8 POLES SCREW CONNECTOR OUTPUTS AT THE SAME TIME NOTES NOTES NOTES The information contained in this publication has been carefully prepared and checked However no res
10. OFF Default White 1 i Default 255 ES MENU Up Down ENTER Es DEFAULT To restore default settings Internal Unit temperature LE no I LA Celsius MENU Up Down CDI ENTER TEMPERATURE Internal Unit temperature visualisation 11 Z1 PLUS LED Controller IS IS IS IS MENU Up Down ENTER Up Down LIFE TIME This menu show the total UNIT life time and the RGB life time Fo a MENU Up Down ENTER TEST MODE RGB colours test with rainbow E a MENU Up Down ENTER SOFTWARE Software version 12 Z1 PLUS LED Controller DISPLAY FUNCTIONS a erge Ge e or Digna Penas Hones Z1 RGBA DISPLAY FUNCTIONS The Z1 display panel shows all the available functions Using these functions it is possible to change some of the parameters and add some functions Changing the D T S setting can vary the functions of the unit so that it does not respond to the DMX 512 signal used to control it Carefully follow the instructions below before carrying out any variations or selections NOTE the symbol 3 shows which key has to be pushed to obtain the desired function Z1 RGBA 4 leds channels output PoS version 2 11 IS IS IS IF FO A ADO MENU Up Down ENTER Up Down ES ES Down AA postion ENTER REVERSE DISPLAY Reverses display s reading depending on o HH Lion IS the mounting position POSSO eee On the ground or suspended p Dawi DISPLAY STAND BY To turn off the display afte
11. SENSOR CODE 03 LA 016 ae 8 pin Female RJ45 RJ45 MALE TO M12 FEMALE CABLE CONVERTER D T S CODE 03 LA 061 FOS 33 all models M12 LED input Male cable connector on board FOS 33 all models 4 2 3 5 8 2 4 6 M12 FEMALE 7 Pint A A 3 M12 MALE FEMALE CABLE M12 MALES CONNECTOR PINOUT 1 RED FC RGBA WHITE 2 RED FC RGBA WHITE 3 GREEN FC RGBA WHITE 4 GREEN FC RGBA WHITE 5 BLUE FC RGBA WHITE 6 BLUE FC RGBA WHITE 7 AMBER RGBA WHITE M12 MALES 8 AMBER RGBA WHITE IMPORTANT The maximum number of FOS 33 Led projectors connectable to the Z1 power supply is 3 pcs The Maximum distance between the Z1 PLUS and the last FOS 33 in the line should not exceed 100 NEVER CONNECT NOR DISCONNECT A LED UNIT WHEN THE POWER SUPPLY IS TURNED NEVER USE BOTH RJ45 AND 8 POLES SCREW CONNECTOR OUTPUTS AT THE SAME TIME 43 Z1 PLUS LED Controller D T S INFRARED REMOTE SENSOR CODE 03 LA 016 migra a re A DODODOOS sE 1 _PIN _8 8 poles plug in screw connector LEDS OUTPUT FOS 100 LEDS CABLE PINOUT 1 RED FC RGBA WHITE 2 RED FC RGBA WHITE 3 GREEN FC RGBA WHITE 4 GREEN FC RGBA WHITE 5 BLUE FC RGBA WHITE 6 BLUE FC RGBA WHITE 7 AMBER RGBA WHITE 8
12. degrees 1829 Macro 1 a Mare O 45589 Macrod IET Macro 75 89 Macros A Marr tosto Maero 7 120134 oo Mero O 135 149 ooo Macro 9 O 150 164 Macro 10 O 165 179 Macro 1 180 194 Macro 12 195 209 Macro 18 210 2235 Macro OS 2262239 MacrolS O OS 240255 TT Macrot 6 O DMX CHANNEL 8 Parameter COLOUR MACROS IF EE ISIS isis EHER PLEASE CHECK PAGE 7 DMX range Value 23 Z1 PLUS LED Controller DMX CHANNEL 8 Parameter COLOUR MACROS IF EE ISIS HS EHER PLEASE CHECK PAGE 7 M DMX range su range Option Function Value degrees 143 150 Rainbow Speed 1 1 Sec 151 158 Rainbow Speed 2 5 Sec 159 166 Rainbow Speed 3 10 Sec 167 174 Rainbow Speed 4 20 Sec 175 182 Rainbow Speed 5 30 Sec 183 190 Rainbow Speed 6 60 Sec 191 198 Rainbow Speed 7 120 Sec PO a Ss a MO a SS 199 206 207 214 215 222 223 230 231 238 239 246 N da x N un un DMX CHANNEL 9 Parameter FUNCTIONS Recall Create and Store the Custom white DMX range Mode Option Function Value Custom White Recall Enable CH 6 for Custom white Recall 80 160 Custom White Create Enable CH 6 for Custom white Creation 161 255 Custom White Store Store the Custom White created 24 Z1 PLUS LED Controller WALL 6 CHANNELS MODE For use with DTS Wall mounted DMX co
13. plug the cable coming from the Power supply into OUT 1 or OUT 2 of the T BOX when other FOCUS FULL COLOUR are connected because a wrong connection can seriously damage the units The Maximum distance between the Z1 PLUS and the last FOCUS FULL COLOUR unit in the line should not exceed 100 meters NEVER CONNECT NOR DISCONNECT A LED UNIT WHEN THE POWER SUPPLY IS TURNED ON NEVER USE BOTH RJ45 AND 8 POLES SCREW CONNECTOR OUTPUTS AT THE SAME TIME a FOC FOCUS FULL COLOUR 6 pin Female RJ12 41 Z1 PLUS LED Controller D T S INFRARED REMOTE SENSOR CODE 03 LA 016 AI 8 pin Female RJ45 nl lee ls um eal on RJ45 MALE TO M12 FEMALE CABLE CONVERTER D T S CODE 03 LA 061 M12 LED input Male cable connector on board FOS 100 all models 7 Pint M12 MALE FEMALE CABLE CONNECTOR PINOUT 1 RED FC RGBA WHITE 2 RED FC RGBA WHITE 3 GREEN FC RGBA WHITE 4 GREEN FC RGBA WHITE 5 BLUE FC RGBA WHITE 6 BLUE FC RGBA WHITE 7 AMBER RGBA WHITE FOS 100 ALL MODELS IMPORTANT The maximum number of FOS 100 connectable to the Z1 Plus Power supply is 1 pcs The Maximum distance between the Z1 PLUS and FOS 100 unit should not exceed 100 meters NEVER CONNECT NOR DISCONNECT A LED UNIT WHEN THE POWER SUPPLY IS TURNED ON NEVER USE BOTH RJ45 AND 8 POLES SCREW CONNECTOR OUTPUTS AT THE SAME TIME 42 Z1 PLUS LED Controller J L S D T S INFRARED REMOTE
14. 16 FULL COLOUR 6 pin Male RJ12 Modular Plug 39 Z1 PLUS LED Controller D T S INFRARED REMOTE SENSOR CODE 03 LA 016 D T S T BOX CODE 03 LA 001 IMPORTANT The maximum number of MR16 FULL COLOUR lamps connectable to the Z1 PLUS Power supply is 5 pcs Never plug the cable coming from the Power supply into OUT 1 or OUT 2 of the T BOX when other MR16 FULL COLOUR lamps are connected because a wrong connection can seriously damage the lamps The Maximum distance between the Z1 PLUS and the last MR16 unit in the line should not exceed 100 meters In order to properly drive the MR16 FULL COLOUR lamps connected to Z1 PLUS power supply BOOST MODE should be disabled and the maximum intensity on Z1 PLUS Power Supply Dimmer Channel should not exeed 70 if all the 3 channels Red Green and Blue are turned ON at the same time and for a long period NEVER CONNECT NOR DISCONNECT A LED UNIT WHEN THE POWER SUPPLY IS TURNED ON NEVER USE BOTH RJ45 AND 8 POLES SCREW CONNECTOR OUTPUTS AT THE SAME TIME p A eel TN O MR16 FULL COLOUR 40 Z1 PLUS LED Controller J L S 0749050 e ORO D T S INFRARED SEO al REMOTE SENSOR SU 8 pin Female RJ45 Ao RA CODE 03 LA 016 D T S T BOX CODE 03 LA 001 IMPORTANT The maximum number of FOCUS FULL COLOUR connectable to the Z1 PLUS Power supply is 5 pcs 6 pin Male RJ12 Modular Plug Never
15. Changing the D T S setting can vary the functions of the unit so that it does not respond to the DMX 512 signal used to control it Carefully follow the instructions below before carrying out any variations or selections NOTE the symbol IRS shows which key has to be pushed to obtain the desired function Z1 PLUS RGB 3 leds channels output Software version 2 11 gr TE POST E MENU Up Down ENTER Up Down ENTER UN Down REVERSE DISPLAY Reverses display s reading depending on the mounting position On the ground or suspended DISPLAY STAND BY IS Stay E ENTER Es Down 2 Display OFF Floor AA oston BE Lion IF IR gt gt position To turn off the display after 5 seconds Display always ON ENTER DMX MODE To select DMX mode 9 DMX channels Or leave it always on IS NJE IS BS QCH 9 CHANNELS I Default DMX Mode 9 CH Up Down ENTER Up Down ENTER 6 CHANNELS mode default 5 DMX channels mode gt ENTER Shutter Dimmer RGB WALL mode IS 6 DMX channels for use with DTS Wall IS ICH 1 CHANNEL ENTER IS ENTER mounted DMX controller 0514L007 M3CH mode 4 DMX channels Dimmer RGB RGB mode 3 channels 1 DMX IS RGB 3 CHANNELS channel mode IS I Shutter Dimmer RGB AUX mode let you activate an external Up Down 5 CHANNELS ENTER IS ON OFF control on IR connector Mene IF M3CH 4 CHANNELS Up Down ENTER CUSTOM DMX mode let you set the parameters for Shutter Dimmer Re
16. DS CONNECTOR PINOUT 8 poles plug in screw connector Pin 1 RED Pin 2 RED Pin 3 GREEN Pin 4 GREEN Pin 5 BLUE Pin 6 BLUE Pin 7 AMBER Pin 8 AMBER LEDS CONNECTOR PINOUT M12 Pin 1 RED Pin 2 RED Pin 3 GREEN Pin 4 GREEN Pin 5 BLUE Pin 6 BLUE Pin 7 AMBER Pin 8 AMBER LED UNITS WIRING CONNECTIONS J L S as 8 pin Female RJ45 zn 6 pin Female RJ12 MR16 RGB 38 Z1 PLUS LED Controller 0749050 x D T S INFRARED REMOTE SENSOR CODE 03 LA 016 D T S T BOX CODE 03 LA 001 IMPORTANT The maximum number of MR16 RGB lamps connectable to the Z1 PLUS Power supply is 15 pcs Never plug the cable coming from the Power supply into OUT 1 or OUT 2 of the T BOX when other MR16 lamps are connected because a wrong connection can seriously damage the lamps The Maximum distance between the Z1 PLUS and the last MR16 unit in the line should not exceed 100 meters NEVER CONNECT NOR DISCONNECT A LED UNIT WHEN THE POWER SUPPLY IS TURNED ON NEVER USE BOTH RJ45 AND 8 POLES SCREW CONNECTOR OUTPUTS AT THE SAME TIME MR16 RGB LED UNITS WIRING CONNECTIONS J L S as 8 pin Female RJ45 os on mmm Li H RE 6 pin Female RJ12 AY o Y SE Le SS MR16 FULL COLOUR Con 6 pin Male RJ12 Modular Plug 6 pin Male RJ12 Modular Plug gt ari 3 SS MR
17. Down your camera recordings BOOST DRIVING This menu allow to increase the LED s current from 350mA to 500 mA rid 5 ENTER ES Down Gree E ENTER Es Down bLUE IS ENTER Es Down SAEH ES ENTER Es Down ES ENTER Up Down A ENTER Up Down iS IS ENTER Up Down Up Down ENTER Default 255 ENTER ENTER Default 255 SP ENTER ENTER Default 255 JQP ENTER Default 4 ENTER Off 25 ms Istant responce to DMX variation 20 250 ms Smooth response to DMX variation Linear Linear courrent output ENTER Quadratic Linear light ENTER output Range 610 Hz 10 KHz Default 610 Hz ENTER Boost mode activated MES ENTER Boost mode deactivated ENTER Whit BOOST active the LED s current is set to 500mA 30 more gain Default Disable O Z1 PLUS LED Controller JE AUEO SS T MENU Up Down ENTER ENTER Up Down AUTOMATIC MODE Automatic demo game without DMX controller ChPr Chase with 16 steps previously created in REC MODE Speed and Wait time selectable by user CUPr RGB values selectable by user Rainbow rAIn Rainbow colours effect Speed time selectable by user CU01 CU16 Color Macros as on DMX channel 8 Macro WHITE MACROS 16 macros for White color from 2000 to 7200 K DIMMER Dimmer level selectable by user as on DMX channel 2 Dimmer Dimmer level is active for all the programs and macros SHUTTER Shutter level selectable by user as on DMX channel
18. ES Whit BOOST active the LED s current is set to 500mA 30 more gain Default Disable TS AUEO SS 7 MENU Up Down ENTER ENTER Up Down AUTOMATIC MODE Automatic demo game without DMX controller ChPr Chase with 16 steps previously created in REC MODE Speed and Wait time selectable by user CUPr RGB values selectable by user Rainbow rAln Rainbow colours effect Speed time selectable by user CU01 CU16 Color Macros as on DMX channel 8 Macro WHITE MACROS 16 macros for White color from 2000 to 7200 K DIMMER Dimmer level selectable by user as on DMX channel 2 Dimmer Dimmer level is active for all the programs and macros SHUTTER Shutter level selectable by user as on DMX channel 1 Shutter Shutter level is active only for CU01 CU16 and Wh01 Wh16 Macros ESC Esc from Automatic Mode Menu Z1 PLUS LED Controller 14 ES SPEE IS Down 00 ifs ES Pas Anbr Anbr 00 iis 280 ids ENTER IS SPEE ES Up Down ENTER Up Down ENTER ENTER Up Down ENTER ES ES 5 Z1 PLUS LED Controller E Se EC OCA MENU Up Down ENTER ENTER REC MODE In DMX Recorder Mode it is possible to create and store the scenes of the ChPr by using an external DMX controller The unit must be setted to 10 channels MODE DMX Recorder Mode For the programming of ChPr by using a DMX controller besides the 10 channels necessary to control the unit a further 3 DMX ch
19. For technical personnel only To operate this menu Connect the unit to the main While reset is running press the MENU and ENTER keys at the same time CHANNELS This menu allow to set 3 channels or 4 channels LEDs output mode 3 LEDs channels output mode Z1 RGB 4 LEDs channels output mode Z1 RGBA Exit from hidden menu 17 Z1 PLUS LED Controller AUTOMATIC OPERATION AUTO Z1PLUS can work in automatic mode without a DMX controller First of all connect the projectors with a DMX cable picture below A maximum quantity of 32 slave units can be connected to the same Master unit MASTER SLAVE 1 SLAVE 2 SLAVE 3 SLAVE 32 ey Mi e ali am z nni 5 ca To activate Auto mode on the first unit use the menu to run through the different modes until AUTO appears on the display at this point press enter Now it is possible to choose between the different pre programmed games CUPr RAIn CU01 CU16 Wh01 Wh16 or ChPr which is user programmable through REC mode To confirm game activation press ENTER on the selected GAME CUPr RAIn CU01 CU16 Wh01 Wh16 The first unit that will work as a Master should be placed in Automatic mode AUTO the other units have to be placed in 9 channels DMX mode MODE 9CH for Z1 PLUS RGB or in 10 channels DMX mode MODE 10 CH for Z1 PLUS RGBA and the DMX address should be set at A001 For Raln rainbow game it is possible to select the speed for the colour changhing SPEE DIMMER function
20. Function Value Es ERA 0 255 Proportionalcolour Parameter WHITE Pre programmed White at diff color temperature DMX range Mode Option Function Value 055 23 No Function 56 105 Full Red Green Blue Amber at Full 106 155 130 White DTS IF CHANNEL 10 FUNCTIONS CUSTOM WHITE RECALL Dmx range value 0 79 156 205 180 Custom White Recall 206 255 225 White CTC Channel 8 CTC enabled 256 color temp Correction Macros 2000 K 7200 K IF CHANNEL 10 FUNCTIONS CUSTOM WHITE CREATE Dmx range value 80 160 156 205 Custom White Create RGBA levels selectable by DMX 206 255 White CTC Channel 8 CTC enabled 256 color temp Correction Macros 2000 K 7200 K 31 Z1 PLUS LED Controller _DMX CHANNEL 8 Parameter CTC Color temperature correction Move DI 25 ronge range Mode Option Function Value degrees IF CHANNEL 7 White WHITE CTC Dmx range value 206 255 0 255 256 color temp Correction Macros 0 2000 K 128 5500 K 255 7200 IF CHANNEL 7 White NO FUNCTION Dmx range value 0 43 0255 No Function y Parameter COLOUR MACROS SS dc e E NAC ESBS GEAR PLEASE CHECK PAGE 12 Move DMX range range Mode Option Function Value E 0 14 14 No Function Function at 1 II Macro 48589 O Macrod __ O O _ IET Macro BA Macros 902104 Macro 6 ASA Magro O_O 120134 oo poo Mares O 135 149 ooo Macro 150 164
21. L xoia _ Parameter AMBER DMX range Value 2 0355 Proportional colour 36 Z1 PLUS LED Controller DMX PROTOCOL Z1 RGBA 4 CHANNELS LED OUTPUT RGBA mode 4 DMX channels 1 RED 2 GREEN 3 BLUE 4 AMBER CT AAA DMX range Mode Option Function Value 2 0255 Proportional colour SA DMX range Mode Option Function Value 0255 Proportional colour AS DMX range Mode Option Function Value 0255 Proportional colour Value 0255 Proportional colour 37 WIRING DIAGRAMS Z1 PLUS LED Controller Z1 is provided with two different connector models for LEDs output RJ45 female panel connector and 8 poles plug in screw connector RJ45 Female RJ45 LED input panel connector male cable connector on board Z1 PLUS LED CONTROLLER 1 EU 8 E ZI 8 8 pin Female RJ45 8 poles plug in screw connector on board Z1 PLUS LED CONTROLLER DIVWVE OVWQE SS 8 1 _PIN _8 poles plug in screw connector M12 LED input M12 LED output Male cable connector Female panel connector on board on board FOS 100 all models Z10 Z1 outdoor led controller LEDS CONNECTOR PINOUT Rj45 Pin 1 RED Pin 2 RED Pin 3 GREEN Pin 4 GREEN Pin 5 BLUE Pin 6 BLUE Pin 7 AMBER Pin 8 AMBER LE
22. NELS LED OUTPUT DMX channel 10 SCENES channel From 0 10 no function r001 From 11 255 are displayed the programmable scenes max 16 scenes from M001 to M0016 DMX channel 11 EDIT channel From 0 19 no function From 20 234 the unit runs the configuration given by the received input DMX values With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record the selected scene From 235 255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene With the channel REC it is possible to record the selected scene as last scene DMX channel 12 RECORDING channel Records the set scene with a variation between O to 255 the display flashes indicating that the scene has been recorded It is advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene If ChPr is not closed by indicating the last scene Edit channel between 235 255 in playback mode all 16 scenes will be played through even if not programmed Z1 PLUS IN RGBA MODE 4 CHANNELS LED OUTPUT DMX channel 11 SCENES channel From 0 10 no function r001 From 11 255 are displayed the programmable scenes max 16 scenes from M001 to M0016 DMX channel 12 EDIT channel From 0 19 no function From 20 234 the unit runs the configuration given by the received input DMX values With the channel SCENES it is p
23. RED MODE NOTE Infrared remote control External infrared remote sensor By activating Ir MODE it will be needed possible to navigate trought the D T S Code 03 LA 016 unit functions by using the D T S infrared remote control D T S Code 0514L008 gt IR IS IS MENU Up Down ENTER Up Down FAN SPEED CONTROL Internal Fan Speed control selectable by user Range OFF 24 volt Default 12 volt m a 4 m ENTER Fan Speed Control Range OFF 24 volt Default 12 volt a gt gt ENTER Up Down ere MENU Up Down CIICI IS ES EMERGENCY Emergency operating mode By setting Emergency mode it will be possible to select one of the 16 preprogrammed WHITE cues that will then ran if DMX Signal is missing or not available Usefull for Emergency EXIT ilumination on public areas ENTER Default OFF Default White 1 Default 255 m m Z Z m m 7 7 y 16 Z1 PLUS LED Controller MENU Up Down ENTER ENTER DEFAULT To restore default settings Internal Unit temperature ENTER ENTER Celsius MENU Up Down TEMPERATURE Internal Unit temperature visualisation IS IS IS IF MENU Up Down ENTER Up Down LIFE TIME This menu show the total UNIT life time and the RGBA life time ENTER ez AS i MENU Up Down ENTER TEST MODE RGB colours test with rainbow IS IF IS E MENU Up Down ENTER SOFTWARE Software version Nu e e HIDDEN MENU
24. X channel 12 RECORDING channel Records the set scene with a variation between 0 to 255 the display flashes indicating that the scene has been recorded It is advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene If ChPr is not closed by indicating the last scene Edit channel between 235 255 in playback mode all 16 scenes will be played through even if not programmed Slave mode for ChPr program All slave units will be synchronised with master unit running their own Chpr program IS IS IS IS MENU Up Down ENTER Up Down INFRARED MODE Infrared remote control By activating Ir MODE it will be possible to navigate trought the unit functions by using the D T S infrared remote control D T S Code 0514L008 LES IR IS IS MENU Up Down ENTER Up Down FAN SPEED CONTROL Internal Fan Speed control selectable by user Range OFF 24 volt Default 12 volt IS FH CNic_ IS IS MENU Up Down II Ls ENTER Up Down SEL IS ENTER ES Down a ENTER ENTER NOTE External infrared remote sensor needed D T S Code 03 LA 016 ENTER Fan Speed Control Range OFF 24 volt Default 12 volt EMERGENCY Emergency operating mode By setting Emergency mode it will be possible to select one of the 16 preprogrammed WHITE cues that will then ran if DMX Signal is missing or not available Usefull for Emergency EXIT ilumination on public areas Default
25. annels are needed So that in RECORDER mode via DMX the unit will need 13 channels to be correctly programmed The three new DMX channels are DMX channel 11 SCENES channel From 0 10 no function r001 From 11 255 are displayed the programmable scenes max 16 scenes from M001 to M0016 DMX channel 12 EDIT channel From 0 19 no function From 20 234 the unit runs the configuration given by the received input DMX values With the channel SCENES it is possible to pass from one step to the next while with REC it is possible to record the selected scene From 235 255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene With the channel REC it is possible to record the selected scene as last scene DMX channel 13 RECORDING channel Records the set scene with a variation between 0 to 255 the display flashes indicating that the scene has been recorded It is advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene If ChPr is not closed by indicating the last scene Edit channel between 235 255 in playback mode all 16 scenes will be played through even if not programmed Fu SL AU SUPE SS p Down ENTER ENTER Up Down SLAVE MODE Slave mode for ChPr program All slave units will be synchronised with master unit running their own Chpr program ENTER IS IS gt gt MENU Up Down ENTER Up Down INFRA
26. d IS SEL Green Blue Ctc Macro and Function to sit E Li Down the desired DMX channels Ig not yet implemented ae Ge Show Custom settings Dimmer RGB SELIR Custom mode enabled ENTER Parameters Setting on MACRO Custom Mod MACRO Function enable channel SS ra mapping macro rainbow effects Corea External ON OFF control on STD default Ue Dow Coase ene ES IR connector Standard mode enabled Mor _ Up Down 101 IL d IS Re mode enabled IES Rainbow effects on MACRO channel Is is Down pa ENTER Default ENTER 8 Z1 PLUS LED Controller IF IF IF IF MENU Up Down ENTER Up Down LED RGB Min Max Smooth Compression Sync and Boost level values settings Up Down IR RGB MINIMUM VALUES This menu allow to select the minimum levels for Red Green and Blue RGB MAXIMUM VALUES This menu allow to select the maximum levels for Red Green and blue Up Down IR These settings have priority on Master Dimmer channel Up Down IR SMOOTH VALUE This menu allow to select the value of the delay in millisecons for RGB and Dimmer channels reaction to DMX or Program variation Off 25 ms delay Fast response 20 250 ms delay Slow response COMPRESSION This menu allow to select between Linear courrent output or Quadratic courrent output for LEDs Default Linear Up Down SYNC This menu allow to adjust the PWM frequency value Hz in order to reduce flickering in the process of Up
27. e open at variable speed from slow to fast 42 6s 100ms 150 179 a Pulse close at variable speed from slow to fast 42 6s 100ms 180 204 192 Random Strobe Master and RGB active 205 229 218 Random Strobe Full 230 234 Red Yellow Cyan and Blue colour effects at variable speed 235 255 245 o Open DMX CHANNEL Parameter DIMMER DMX range Value DMX range Value 0255 Proportional colour 26 Z1 PLUS LED Controller ae ms DMX range Mode Option Function Value 0255 Proportional colour Pr DMX range Mode Option Function Value 0255 o op Proportional colour 27 Z1 PLUS LED Controller DMX PROTOCOL Z1 RGB 3 CHANNELS LED OUTPUT M3CH mode 4 DMX channels Dimmer RGB 1 DIMMER 2 RED 3 GREEN 4 BLUE DMX CHANNEL Parameter DIMMER DMX range Value DMX range Mode Option Function Value prep Proportional colour e DMX range Mode Option Function Value 0255 o Proportional colour an Pa DMX range Mode Option Function Value 0255 o op Proportional colour 28 Z1 PLUS LED Controller DMX PROTOCOL Z1 RGB 3 CHANNELS LED OUTPUT RGB mode 3 DMX channels 1 RED 2 GREEN 3 BLUE DET Move DAMA range range Mode Option Function Value Se Og 0 255 Proportional colour IA Move L AIDE range range Mode Option Function Value PA Og 0 255 Proportional colour TE Move DID range range Mode Option Function Value SE I
28. een pin 2 and 3 The DMX terminator must be plugged into the last unit DMX out panel connector of the DMX line PLACE A 120 OHM RESISTOR BETWEEN PIN 2 AND 3 OF A MALE XRL CONNECTOR AND PLUG IT INTO THE DMX OUT PANEL CONNECTOR OF THE LAST UNIT CONNECTED TO THE DMX LINE PIN 3 PIN 2 The standard configuration of the Z1 PLUS is with XLR 5 pins connectors 6 Z1 PLUS LED Controller DMX ADDRESS Z1 PLUS can be set at 3 RGB or 4 RGBA leds channels output please refer to page 16 for details Z1 PLUS RGB can be used in seven different modes 9 DMX channels mode default 5 DMX channels mode Shutter Dimmer RGB WALL mode 6 DMX channels for use with DTS Wall mounted DMX controller 0514L007 M3CH mode 4 DMX channels Dimmer RGB RGB mode 3 channels 1 DMX channel mode or CUSTOM DMX mode not yet implemented Z1 PLUS RGBA can be used in seven different modes 10 DMX channels mode default 6 DMX channels mode Shutter Dimmer RGBA WALL mode 6 DMX channels for use with DTS Wall mounted DMX controller 0514L007 M4CH mode 5 DMX channels Dimmer RGBA RGBA mode 4 channels 1 DMX channel mode or CUSTOM DMX mode not yet implemented If you want to use the Z1 PLUS RGB in WALL mode select the WALL mode from the MODE menu and set the following addresses on the mixer To be used only with DTS Wall mounted DMX controller 0514L007 If you want to select the next projector just add
29. ent ne peut tre copi photocopi ou reproduit dans sa totalit ou partiellement sans le consentement pr alable de D T S D T S se r serve le droit d apporter toutes modifications et am liorations esthetiques fonctionnelles ou de design sans pr avis a chacun de ses produits D T S d cline toute responsabilit sur l utilisation ou sur l application des produits ou des circuits d crits Las informaciones contenidas en este documento han sido cuidadosamenteredactadas y controladas Con todo no se asume ninguna responsabilidad por eventuales inexactitudes Todos los derechos han sido reservados y este documento no puede ser copiado fotocopiado o reproducido total o parcialmente sin previa autorizaci nescrita de D T S D T S se reserva el derecho a aportar sin previo aviso cambios y modificaciones de car cter est tico funcional o de dise o a cada producto suyo D T S no se asume responsabilidad de ning n tipo sobre la utilizaci n o sobre la aplicaci n de los productos o de los circuitos descritos 3 Z1 PLUS LED Controller IMPORTANT SAFETY INFORMATION Fire prevention Never locate the fixture on any flammable surface Minimum distance from flammable materials 10 cm Replace any blown or damaged fuses only with those of identical value Prevention from electric shock High voltage is present inside the unit Unplug the unit prior to performing any operation which involves touching the inside of the unit This equi
30. er DUE CHANNEL EN Parameter GREEN Ga Move DAMA camge range Mode Option Function Value Se 0 255 Proportionalcolour DMX CHANNEL Parameter BLUE a Move DMX range range Mode Option Function Value aS os 0 255 Proportional colour DMX CHANNEL 6 Parameter WHITE Pre programmed White at diff color temperature DMX range Mode Option Function Value 055 No Function 56 105 80 Full Red Green Blue at Full 106 155 130 White DTS IF CHANNEL 9 FUNCTIONS CUSTOM WHITE RECALL Dmx range value 0 79 156 205 180 Custom White Recall 206 255 225 White CTC Channel 7 CTC enabled 256 color temp Correction Macros 2000 K 7200 K IF CHANNEL 9 FUNCTIONS CUSTOM WHITE CREATE Dmx range value 80 160 156 205 Custom White Create RGB levels selectable by DMX 206 255 White CTC Channel 7 CTC enabled 256 color temp Correction Macros 2000 K 7200 K _DMX CHANNEL 7 Parameter CTC Color temperature correction Move ee range Mode Option Function Value degrees IF CHANNEL 6 White WHITE CTC Dmx range value 206 255 0 255 256 color temp Correction Macros 0 2000 K 128 5500 K 255 7200 K IF CHANNEL 6 White NO FUNCTION Dmx range value 0 55 0255 No Function 22 Z1 PLUS LED Controller DMX CHANNEL 8 Parameter COLOUR MACROS IF Ss IS IS HIS GL S PLEASE CHECK PAGE 7 Move DMA range range Mode Option Function Value
31. ns PROG In Automatic mode let you scroll between the selectable games OK RED GREEN YELLOW BLUE buttons Hi Direct acces to Automatic mode for Red Green Blue Yellow colour macros Red CU01 Green CU07 Yellow CU04 Blue CU13 Navigation buttons Same as UP DOWN on unit display OK button Same as ENTER on unit display MENU button Same as MENU on unit display ON OFF Button 1 9 Buttons PROG Buttons R G Y B Buttons MENU Button 20 Z1 PLUS LED Controller DMX PROTOCOL Z1 PLUS RGB 3 CHANNELS LED OUTPUT 9 CHANNELS MODE Default 1 SHUTTER 2 DIMMER 3 RED 4 GREEN 5 BLUE 6 WHITE Pre programmed whites at different color temperatures 7 CTC 8 COLOURS MACRO 9 FUNCTIONS DMX DMX CHANNEL Em Parameter SHUTTER Move Value E Black out O Open 20 29 CA Black out 30 119 Strobe at variable speed from slow to fast 3700ms 20ms 120 149 Pulse open at variable speed from slow to fast 42 6s 100ms 150 179 Lg Pulse close at variable speed from slow to fast 42 6s 100ms 180 204 192 Random Strobe Master and RGB active 205 229 218 Random Strobe Full 230 234 Red Yellow Cyan and Blue colour effects at variable speed 235 255 245 _____ Open DMX CHANNEL Parameter DIMMER ai Move DAMA panes range Mode Option Function Value mans 0 255 Proportional dimmer BE Move Value Se Ceres 0 255 Proportional colour 21 Z1 PLUS LED Controll
32. ntroller 0514L007 IS IS IS IS IS GREEN MEN Up Down ENTER Up Down O CHANNELS ENTER 1 2 RED 3 BLUE 4 DIMMER 5 NOT USED 6 SHUTTER DMX CHANNEL 1 Parameter GREEN DMX range Mode Option Function Value 0255 Proportional colour DMX CHANNEL 2 Parameter RED DMX range Mode Option Function Value 0255 gt op Proportional colour Parameter BLUE DMX range Mode Option Function Value Parameter DIMMER DMX range Value DMXCHANNEL 5 Parameter NOT USED DMX range Value DMX CHANNEL 6 Parameter SHUTTER 098 5 Black out 1019 Open Black out Strobe at variable speed from slow to fast 3700ms 20ms 120 149 a Pulse open at variable speed from slow to fast 42 6s 100ms 150 179 nd Pulse close at variable speed from slow to fast 42 6s 100ms DMX range Value 180 204 192 nn Random Strobe Master and RGB active 205 229 218 Random Strobe Full 230 234 Red Yellow Cyan and Blue colour effects at variable speed 235 255 245 Open 25 Z1 PLUS LED Controller DMX PROTOCOL Z1 RGB 3 CHANNELS LED OUTPUT 5 CHANNELS MODE Shutter Dimmer RGB 1 SHUTTER 2 DIMMER 3 RED 4 GREEN D BLUE jt 1 Parameter SHUTTER Move DAD denge range Mode Option Function Value n ss Black out a a EL Open 2029 24 Black out 30 119 Strobe at variable speed from slow to fast 3700ms 20ms 120 149 Puls
33. ossible to pass from one step to the next while with REC it is possible to record the selected scene From 235 255 the unit runs the configuration given by the received input DMX values closing the sequence as last scene With the channel REC it is possible to record the selected scene as last scene DMX channel 13 RECORDING channel Records the set scene with a variation between O to 255 the display flashes indicating that the scene has been recorded It is advised that you keep the REC channel set to 0 and to run through the 255 only once you have decided to save the scene If ChPr is not closed by indicating the last scene Edit channel between 235 255 in playback mode all 16 scenes will be played through even if not programmed 19 Z1 PLUS LED Controller INFRARED REMOTE CONTROL By activating Ir MODE on Z1 PLUS Menu it will be possible to navigate trought the unit functions by using the D T S infrared remote control D T S Code 0514L008 Please note that external infrared remote sensor is also needed D T S Code 03 LA 016 Infrared remote control functions ON OFF and MUTE buttons 7 In Automatic mode let you stop the games running Button Master and slaves will go in Stand by mode 1 9 buttons VOL In Automatic mode let you select the colour macros 1 9 DALE 1 Button In Automatic mode let you select the colour macros 10 16 VOL NAVIGATION In Automatic mode let you select the desired value for DIMMER Butto
34. pment must be grounded do not connect to non grounded supplies The use of a thermal magnetic circuit breaker is recommended for each Z1 PLUS Use only AC supplies 90 260V 50 60Hz The unit should never be located in position exposed to rain or in areas of extreme humidity A good air ventilation is essential for proper equipment work Safety The external surface of the unit may exeed 50 C never handle the unit until at least 5 minutes have elapsed since the unit was turned off Never install the unit in an enclosed area lacking sufficient air flow The ambient temperature should not exeed 40 C and should not be lower than 10 C DESCRIPTION Z1PLUS DMX 512 LED controller is a unit dedicated to the following LED products by D T S MR16 RGB LED lamp MR16 full color LED lamp FOCUS LED projectors HELIOS LED projectors FOS led bars 4 channels output DMX 512 Power interface able to drive RGB AMBER LED units Max 100W per output 25W per channel 25W Red 25W Green 25W Blue 25W Amber 4 x 350mA electronically dimmable led control outputs 500mA 100 per channel in BOOST Mode Main Input voltage range is 90V 260V 50 60 HZ It is possible to use this item through every DMX 512 mixer or by using the DTS InfraRed control MAIN ELECTRICAL CHARACTERISTICS Input Voltage Range Vin 90 260 Vac Frequency 50 60 HZ Power Consumption Range 8 100 W Power Factor Pf 0 95 electronic PFC controller Efficiency 90
35. ponsibility will be taken for any errors All rights are reserved and this document cannot be copied photocopied or reproduced in part or completely without prior written consent from D T S D T S reserves the right to make any aesthetic functional or design modifications to any of its products without prior notice D T S assumes no responsibility for the use or application of the products or circuits described herein MADE IN ITALY C The Lighting Company ISO 9001 2000 D T S quality system is certified to the ISO 9001 2000 standard D T S products are designed and manufactured at the D T S plants in Italy 05171184 D T S Illuminazione s r l Via Fagnano Selve 10 12 14 47843 Misano Adriatico RN Italy Tel 39 0541 611131 Fax 39 0541 611111 info dts lighting it www dts lighting it
36. r 5 seconds Display TES Or leave it always on always ON ENTER RS RS RS RS 10 CHANNELS Is Default DMX Mode 10 CH MENU Up Down ENTER Up Down DMX MODE IR 6 CHANNELS Up Down ENTER To select DMX mode 10 DMX channels mode default 6 DMX channels mode Shutter Dimmer RGBA WALL E 1 CHANNEL n mode 6 DMX channels for use with DTS Wall mounted DMX controller 0514L007 M4CH mode 5 DMX gt RGBA 4 CHANNELS ENTER channels Dimmer RGBA RGBA mode 4 channels 1 DMX channel mode ks 6 CHANNELS Up Down ENTER AUX mode let you activate an external ON OFF control on IR connector not yet implemented LSA M4CH 5 CHANNELS T Dimmer RGBA CUSTOM DMX mode let you set the RS SELIR Custom mode enabled parameters for Shutter Dimmer Red Up Down IS is Down ENTER not yet implemented Parameters Setting on ENTER Custom Mode Green Blue Amber Ctc Macro and Function to the desired DMX channels Brel Shot E Show Custom settings MACRO MACRO Function enable channel la rs 10 104 AUX MODE External ON OFF control on ME rainbow effects US MU ENTER IR connector Standard mode enabled na r r ES Default Up Pown me en mode enabled IES Rainbow effects on MACRO channel ENTER 3 Z1 PLUS LED Controller IF gt IS IF MENU Up Down ENTER Up Down LED RGBA Min Max Smooth and Compression level values settings Up Down IE RGBA MINIMUM VALUES This menu allow to select the minimum levels for Red G
37. reen Blue and Amber Up Down IR RGBA MAXIMUM VALUES This menu allow to select the maximunm levels for Red Green Blue and Amber These settings have priority on Master Dimmer Up Down SMOOTH VALUE This menu allow to select the value IR of the delay in millisecons for RGBA and Dimmer channels reaction to DMX or Program variation Off 25 ms delay Fast response 20 250 ms delay Slow response COMPRESSION This menu allow to select between Up Down Linear current output or Quadratic current output for LEDs Default Linear SYNC This menu allow to adjust the PWM Up Down frequency value Hz in order to reduce flickering in the process of your camera recordings BOOST DRIVING This menu allow to increase the LED s current from 350mA to 500 mA ENTER m a 4 m ENTER ENTER Oni IL ENTER gt gt Up Down Up Down Up Down Up Down Up Down Up Down Up Down Up Down Up Down Default 0 Default 255 ENTER Default 0 E a Default 255 m 4 m A Default 0 Default 255 a Default 0 RRP Default 255 m A m A Range Off 20 IS Default 4 ENTER Off 25 ms Istant responce to DMX variation 20 250 ms Smooth response to DMX variation Linear Linear courrent output ENTER Quadratic Linear light ENTER output Range 610 Hz 10 KHz ENTER Default 610 Hz Boost mode activated IS ENTER Boost mode deactivated
38. ustom white Creation 161 255 D Custom White Store Store the Custom White created 33 Z1 PLUS LED Controller DMX PROTOCOL Z1 RGBA 4 CHANNELS LED OUTPUT 6 CHANNELS MODE Shutter Dimmer RGBA SHUTTER DIMMER RED GREEN BLUE AMBER O U1 W N M PE 1 Parameter SHUTTER DMX range Mode Option Function Value Black out a A ERE Open 2029 a Black out 30 119 Strobe at variable speed from slow to fast 3700ms 20ms 120 149 Pulse open at variable speed from slow to fast 42 6s 100ms 150 179 Pulse close at variable speed from slow to fast 42 6s 100ms 180 204 192 Random Strobe Master and RGB active 205 229 218 Random Strobe Full 230 234 Red Yellow Cyan and Blue colour effects at variable speed 235 255 245 Open DMX CHANNEL Parameter DIMMER DMX range Value DMX range Value 0255 Proportional colour 34 Z1 PLUS LED Controller ae ms DMX range Mode Option Function Value 0255 Proportional colour Pr DMX range Mode Option Function Value 0255 Proportional colour CT tn DMX range Mode Option Function Value 02585 o op Proportional colour 35 Z1 PLUS LED Controller DMX PROTOCOL Z1 RGBA 4 CHANNELS LED OUTPUT M4CH mode 5 DMX channels Dimmer RGBA DIMMER RED GREEN BLUE AMBER U A WN re DMX CHANNEL Parameter DIMMER DMX range Value DMX range Value DMX range Value DMX range Value DMX CHANNE

Z1 PLUS DMX-512 LED CONTROLLER User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents